Wire-up flush_dcache, readq- and writeq-like gic-v3-its assessors, so
GICv3 ITS gets all it needs to be built and run.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
readq and writeq type of assessors are not supported in AArch32, so we
need to specialise them and glue later with series of 32-bit accesses
on AArch32 side.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
It'd be better to switch to CMA... but before that done redirect
flush_dcache operation, so 32-bit implementation could be wired
latter.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
GITS_BASER<n>'s Entry Size is much smaller than 64-bit, but when it
used as a divider it forces compiler to generate __aeabi_uldivmod if
build in 32-bit mode. So, casting it to int (like it is done in other
places) where used as a divider would give a hint to compiler that
32-bit division can be used.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Make sure that constants which are supposed to be applied on 64-bit
data is actually unsigned long long, so they won't be truncated when
used in 32-bit mode.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The workaround for Cavium ThunderX erratum 23154 has a homebrew
pipeflush built out of NOP sequences around the read of the IAR.
This patch converts the code to use the new nops macro, which makes it
a little easier to read.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The GIC system registers are accessed using open-coded wrappers around
the mrs_s/msr_s asm macros.
This patch moves the code over to the {read,wrote}_sysreg_s accessors
instead, reducing the amount of explicit asm blocks in the arch headers.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
TPS65217 INT pin is used for the system wakeup from suspend mode.
This patch enables push button or charger input event as a wakeup source.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Rework the IRQ handler by using HW IRQ number and status bit.
Each HW IRQ number is matched with TPS65217 register layout[*].
(USB IRQ number is 0, AC is 1, Push button is 2)
When an interrupt is enabled, mask bit should be cleared (unmasked).
If an interrupt is disabled, then mask bit should be set (masked).
This mask value is updated into the TPS65217 register in irq_sync_unlock().
Mask bit and interrupt status bit can be handled with HW IRQ number.
Eventually, additional IRQ data, 'tps65217_irqs[]' and the function,
'irq_to_tps65217_irq()' are not necessary.
[*] TPS65217 interrupt register layout
Bit7 6 5 4 3 2 1 0
----------------------------------------------
| x | PBM | ACM | USBM | x | PBI | ACI | USBI
PBM: Push button status change interrupt mask
ACM: AC interrupt mask
USBM: USB power status change interrupt mask
PBI: Push button status change interrupt
ACI: AC power status change interrupt
USBI: USB power status change interrupt
x: Not used
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
TPS65217 interrupt register includes read/writeable mask bits with
read-only status bits. (bit 4, 5, 6 are R/W, bit 0, 1, 2 are RO)
And reserved bit is not required.
Register update operation is preferred for disabling all interrupts during
the device initialisation.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
TPS65217 MFD is an interrupt controller and MFD slave devices like
tps65217-charger and tps65217-pwrbutton request an interrupt to handle
each HW event.
Currently, TPS65217 IRQ name is not defined, so the result is as below.
root@arm:~# cat /proc/interrupts
...
182: 0 INTC 7 Level tps65217-irq
183: 0 - 1 Edge tps65217-charger
185: 0 - 2 Edge tps65217_pwrbutton
This patch specifies the name of the interrupt controller.
182: 0 INTC 7 Level tps65217-irq
183: 0 tps65217 1 Edge tps65217-charger
185: 0 tps65217 2 Edge tps65217_pwrbutton
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
palmas_dev and palmas_power_off are always assigned together.
So the check for palmas_dev inside palmas_power_off function
is redundant. Removing the same.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As DCVDD will often be supplied by a child node of the MFD, we
can't call mfd_remove_devices as the first step in arizona_dev_exit
as might be expected (tidy up the children before we tidy up the
MFD). We need to disable and put the DCVDD regulator before we call
mfd_remove_devices, to prevent PM runtime from turning this back on we
also need to disable the PM runtime before we do this. Finally we can
not clean up the IRQs until all the MFD children have been removed, as
they may have registered IRQs themselves.
This creates a window of time where the interrupts are enabled but
the PM runtime, on which the IRQ handler depends, is not available,
any interrupts in this window will go unhandled and fill the log with
failed to resume device messages. To avoid this we simply disable the
main IRQ at the start of arizona_dev_exit, we don't need to actually
handle any IRQs in this window as we are removing the driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds support to PM8821 PMIC and interrupt support.
PM8821 is companion device that supplements primary PMIC PM8921 IC.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Enable MWI mechanism if PCI bus master supports it.
It might be potential benefit in some cases. Documentation [1] says that
standard Memory Write might supply more current data than in the CPU modified
cache line and "trashing a line in the cache may trash some data that is more
current that in the memory line". This allows to avoid potential retries and
other performance degradation issues on the bus.
[1] PCI System Architecture, 4th edition, ISBN: 0-201-30974-2, pp.117-119.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is,
the differences are:
+ DCDC4/DCDC5
+ LDO7-10
+ Slightly different output voltage/currents
+ 32kHz Output
+ RTC
+ USB Charger detection
Signed-off-by: Pierre-Hugues Husson <phh@phh.me>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP806 supports either master/standalone or slave mode.
Slave mode allows sharing the serial bus, even with multiple
AXP806 which all have the same hardware address.
This is done with extra "serial interface address extension",
or AXP806_BUS_ADDR_EXT, and "register address extension", or
AXP806_REG_ADDR_EXT, registers. The former is read-only, with
1 bit customizable at the factory, and 1 bit depending on the
state of an external pin. The latter is writable. Only when
the these device addressing bits (in the upper 4 bits of the
registers) match, will the device respond to operations on
its other registers.
Add these 2 registers to the regmap so we can access them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix a typo in MODULE_DEVICE_TABLE(). 'pmic_acpi_ids' should be
'bxtwc_acpi_ids'.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Make sure to drop the reference taken by bus_find_device_by_name()
before returning from mfd_clone_cell().
Fixes: a9bbba9963 ("mfd: add platform_device sharing support for mfd")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
'i2c_new_dummy()' does not return an error pointer, so the test can be
simplified to be more consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The new sun4i mfd driver is lacking a dependency, triggering very rarely
int randconfig kernel builds:
drivers/mfd/sun4i-gpadc.o: In function `sun4i_gpadc_probe':
sun4i-gpadc.c:(.text.sun4i_gpadc_probe+0x110): undefined reference to `devm_regmap_add_irq_chip'
This adds a 'select REGMAP_IRQ', as the other drivers with this problem do.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config ABX500_CORE
drivers/mfd/Kconfig: bool "ST-Ericsson ABX500 Mixed Signal Circuit register functions"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We replace module.h with init.h and export.h ; the latter since the
file does export some symbols.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config AB8500_CORE
drivers/mfd/Kconfig: bool "ST-Ericsson AB8500 Mixed Signal Power Management chip"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
We replace module.h with init.h and export.h -- the latter since the file
does make use of EXPORT_SYMBOL.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config AB8500_GPADC
drivers/mfd/Kconfig: bool "ST-Ericsson AB8500 GPADC driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config AB8500_DEBUG
drivers/mfd/Kconfig: bool "Enable debug info via debugfs"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config AB8500_CORE
drivers/mfd/Kconfig: bool "ST-Ericsson AB8500 Mixed Signal Power Management chip"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We replace module.h with moduleparam.h ; the latter since this file
was implicitly relying on getting it.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config AB3100_CORE
drivers/mfd/Kconfig: bool "ST-Ericsson AB3100 Mixed Signal Circuit core functions"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only. In doing
so, the debugfs unregister fcn becomes unused so we remove it too.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Trivial spelling mistake fixes in dev_err message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
No need to use irq_create_mapping (although there is no issue with
doing so) when we are only looking up an existing mapping. Just to
streamline things a little and make the code a little more clear
change some calls from irq_create_mapping to irq_find_mapping.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The kernel WARNs and then crashes today if wm8994_device_init() fails
after calling devm_regulator_bulk_get().
That happens because there are multiple devices involved here and the
order in which managed resources are freed isn't correct.
The regulators are added as children of wm8994->dev. Whereas,
devm_regulator_bulk_get() receives wm8994->dev as the device, though it
gets the same regulators which were added as children of wm8994->dev
earlier.
During failures, the children are removed first and the core eventually
calls regulator_unregister() for them. As regulator_put() was never done
for them (opposite of devm_regulator_bulk_get()), the kernel WARNs at
WARN_ON(rdev->open_count);
And eventually it crashes from debugfs_remove_recursive().
Fix the kernel warnings and crashes by using regulator_bulk_get()
instead of devm_regulator_bulk_get() and explicitly freeing the supplies
in exit paths.
Tested on Exynos 5250, dual core ARM A15 machine.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
mach/hardware.h is needed on C source code side, not header.
And struct davinci_vc is duplicated definition.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the trailing spaces on the register default lines to
stop checkpatch complaining.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When building for X86 using COMPILE_TEST we get this warning:
../drivers/mfd/sun4i-gpadc.c: In function ‘sun4i_gpadc_probe’:
../drivers/mfd/sun4i-gpadc.c:110:10: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Since an integer and a pointer are difference sizes on 64bit architectures.
Convert to case to a long instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The i2c subsys does not load modules by compatible, only by
i2c-id, with e.g. a modalias of: "i2c:axp209".
Populate the axp20x_i2c_id[] table with supported ids, so that
module auto-loading will work.
Reported-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap devicetree binding documentation states that a native-endian
property should be supported as well as big-endian & little-endian,
however syscon in its duplication of the parsing of these properties
omits support for native-endian. Fix this by setting
REGMAP_ENDIAN_NATIVE when a native-endian property is found.
Cc: linux-mips@linux-mips.org
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Tested-by: Maciej W. Rozycki <macro@imgtec.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
DEV_OFF and DEV_OFF_RST functions for RK808 are designed error that
only DEV_OFF_RST can power off supplies. RK818 has been fixed this
issue, so that DEV_OFF is used to power off supplies.
Signed-off-by: Jianhong Chen <chenjh@rock-chips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/mfd/fsl-imx25-tsadc.ko | grep alias
alias: platform:mx25-tsadc
After this patch:
$ modinfo drivers/mfd/fsl-imx25-tsadc.ko | grep alias
alias: platform:mx25-tsadc
alias: of:N*T*Cfsl,imx25-tsadcC*
alias: of:N*T*Cfsl,imx25-tsadc
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/mfd/hi655x-pmic.ko | grep alias
After this patch:
$ modinfo drivers/mfd/hi655x-pmic.ko | grep alias
alias: of:N*T*Chisilicon,hi655x-pmicC*
alias: of:N*T*Chisilicon,hi655x-pmic
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver only has runtime but no build time dependency with ARCH_U300 ||
ARCH_U8500 So it can be built for testing purposes if COMPILE_TEST option
is enabled.
This is useful to have more build coverage and make sure that the driver
is not affected by changes that could cause build regressions.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver is meant for Exynos systems so do not offer the option
elsewhere unless build-testing.
Cc: Inha Song <ideal.song@samsung.com>
Cc: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When building with extra warnings enabled, most files including
linux/mfd/tps65912.h warn about a static variable defined in the
header:
include/linux/mfd/tps65912.h:331:35: warning: 'tps65912_regmap_config' defined but not used [-Wunused-const-variable=]
We also duplicate the data structure between the i2c and spi front-end
drivers. Moving it into the driver code avoids the warning and
the duplication.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The order in which resources were freed in wm8994_device_exit() isn't
correct. The regulators are removed before they are disabled.
Fix it by reordering code a bit, which makes it exact opposite of
wm8994_device_init() as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These can fit in a single line (80 columns), don't split lines
unnecessarily.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The OF is not a strict build-time dependency so max77620 and max77686
can be compile tested to increase build coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the correct function name in one case and adjust a variable name to
that of the corresponding function parameter in another case.
Issue detected using Coccinelle (http://coccinelle.lip6.fr/)
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Allwinner SoCs all have an ADC that can also act as a touchscreen
controller and a thermal sensor. For now, only the ADC and the thermal
sensor drivers are probed by the MFD, the touchscreen controller support
will be added later.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Altera Arria10 Devkit System Resource chip is a Multi-Function
Device with a GPIO expander.
This patch adds documentation for the Altera A10-SR DT bindings.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We get the following warning with the driver is compiled in:
WARNING: modpost: Found 1 section mismatch(es).
To see full details build your kernel with:
'make CONFIG_DEBUG_SECTION_MISMATCH=y'
With CONFIG_DEBUG_SECTION_MISMATCH enabled, the details are reported:
WARNING: vmlinux.o(.text+0x55d014): Section mismatch in reference from the
function fsl_guts_probe() to the function
.init.text:of_flat_dt_get_machine_name()
The function fsl_guts_probe() references
the function __init of_flat_dt_get_machine_name().
This is often because fsl_guts_probe lacks a __init
annotation or the annotation of of_flat_dt_get_machine_name is wrong.
This patch fixes the issue by using the normal DT/OF API rather than
the of_flat_* one.
Cc: Scott Wood <oss@buserror.net>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC of T4240-R1.0-R2.0 has incorrect vender version and spec version.
Acturally the right version numbers should be VVN=0x13 and SVN = 0x1.
This patch adds the GUTS driver support for eSDHC driver to match SoC.
And fix host version to avoid that incorrect version numbers break down
the ADMA data transfer.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Scott Wood <oss@buserror.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>