It is the 10th processor in the well-known imx6 series, and derived
from imx6ul but cost optimized. The more information about imx6ull
can be found at:
http://www.nxp.com/products/microcontrollers-and-processors/
arm-processors/i.mx-applications-processors/i.mx-6-processors
/i.mx6qp/i.mx-6ull-single-core-processor-with-arm-cortex-a7-core
:i.MX6ULL
imx6ul.dtsi is the SoC common stuff for both imx6ul and imx6ull;
imx6ul-14x14-evk.dts is the board common stuff for both imx6ul
and imx6ull 14x14 evk. In this patch, for SoC part, the
imx6ull.dtsi includes imx6ul.dtsi; for board part, imx6ull-14x14-evk.dts
includes imx6ul-14x14-evk.dts.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the latest revision of the datasheet, the LVDS I/O pins
must be enabled before starting the PLL. Fix it.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The VSL and HSL bits in the DSMR register set the corresponding
horizontal and vertical sync signal polarity to active high. The code
got it the wrong way around, fix it.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
There is a bug in the setting of the DES (Display Enable Signal)
register. This current setting occurs 1 dot left shift. The DES
register should be set minus one value about the specifying value
with H/W specification. This patch corrects it.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Dot clock routing is setup through different registers depending on the
DU generation. The code has been designed for Gen2 and hasn't been
updated since. This works thanks to good reset default value, but isn't
very safe. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Document the R8A7796-specific DT bindings and support them in the
driver. The HDMI output is currently not supported.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add support for the R8A7792 DU; it has 2 DPAD (RGB) outputs.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
It isn't safe to call drm_dev_unregister() without first initializing
mode setting with drm_mode_config_init(). This leads to a crash if
either IO memory can't be remapped or vblank initialization fails.
Fix this by reordering the initialization sequence. Move vblank
initialization after the drm_mode_config_init() call, and move IO
remapping before drm_dev_alloc() to avoid the need to perform clean up
in case of failure.
While at it remove the explicit drm_vblank_cleanup() call from
rcar_du_remove() as the drm_dev_unregister() function already cleans up
vblank.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The previous commit 1535aa75a3 ("qla2xxx: fix invalid DMA access after
command aborts in PCI device remove") introduced a regression during an
EEH recovery, since the change to the qla2x00_abort_all_cmds() function
calls qla2xxx_eh_abort(), which verifies the EEH recovery condition but
handles it heavy-handed. (commit a465537ad1 "qla2xxx: Disable the
adapter and skip error recovery in case of register disconnect.")
This problem warrants a more general/optimistic solution right into
qla2xxx_eh_abort() (eg in case a real command abort arrives during EEH
recovery, or if it takes long enough to trigger command aborts); but
it's still worth to add a check to ensure the code added by the previous
commit is correct and contained within its owner function.
This commit just adds a 'if (!ha->flags.eeh_busy)' check around it.
(ahem; a trivial fix for this -rc series; sorry for this oversight.)
With it applied, both PCI device remove and EEH recovery works fine.
Fixes: 1535aa75a3 ("scsi: qla2xxx: fix invalid DMA access after command aborts in PCI device remove")
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use correct index on q, use h->intr_mode instead of i. Issue detected
using static analysis with cppcheck
Fixes: bc2bb1543e ("scsi: hpsa: use pci_alloc_irq_vectors and automatic irq affinity")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to typo "repsonse" to "response" in dev_dbg message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake "suspeneded" to "suspended" in dev_warn
messages.
[mkp: corrected description. Patch is against the isci driver, not iscsi]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A couple of dev_printk messages spans two lines and the literal string
is missing a white space between words. Add the white space.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is required to hold the queue lock when calling blk_run_queue_async()
to avoid that a race between blk_run_queue_async() and
blk_cleanup_queue() is triggered. Additionally, remove the get_device()
and put_device() calls from fc_bsg_goose_queue. It is namely the
responsibility of the caller of fc_bsg_goose_queue() to ensure that the
bsg queue does not disappear while fc_bsg_goose_queue() is in progress.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: James Smart <james.smart@avagotech.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When dynamically unloading overlays, it is important that freed pins are
restored to being inputs to prevent functions from being enabled in
multiple places at once.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Contrary to the documentation, the BCM2835 GPIO controller actually
has four interrupt lines - one each for the three IRQ groups and one
common. Confusingly, the GPIO interrupt groups don't correspond
directly with the GPIO control banks. Instead, GPIOs 0-27 generate IRQ
GPIO0, 28-45 IRQ GPIO1 and 46-53 IRQ GPIO2.
Awkwardly, the GPIOs for IRQ GPIO1 straddle two 32-entry GPIO banks,
so split out a function to process the interrupts for a single GPIO
bank.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add "rockchip,rk1108-dw-mshc", "rockchip,rk3288-dw-mshc" for
dwmmc on rk1108 platform.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
->queue_rq() should return one of the BLK_MQ_RQ_QUEUE_* constants, not
an errno.
f4aa4c7bba ("block: loop: convert to per-device workqueue")
Signed-off-by: Omar Sandoval <osandov@fb.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull networking fixes from David Miller:
1) Fix off by one wrt. indexing when dumping /proc/net/route entries,
from Alexander Duyck.
2) Fix lockdep splats in iwlwifi, from Johannes Berg.
3) Cure panic when inserting certain netfilter rules when NFT_SET_HASH
is disabled, from Liping Zhang.
4) Memory leak when nft_expr_clone() fails, also from Liping Zhang.
5) Disable UFO when path will apply IPSEC tranformations, from Jakub
Sitnicki.
6) Don't bogusly double cwnd in dctcp module, from Florian Westphal.
7) skb_checksum_help() should never actually use the value "0" for the
resulting checksum, that has a special meaning, use CSUM_MANGLED_0
instead. From Eric Dumazet.
8) Per-tx/rx queue statistic strings are wrong in qed driver, fix from
Yuval MIntz.
9) Fix SCTP reference counting of associations and transports in
sctp_diag. From Xin Long.
10) When we hit ip6tunnel_xmit() we could have come from an ipv4 path in
a previous layer or similar, so explicitly clear the ipv6 control
block in the skb. From Eli Cooper.
11) Fix bogus sleeping inside of inet_wait_for_connect(), from WANG
Cong.
12) Correct deivce ID of T6 adapter in cxgb4 driver, from Hariprasad
Shenai.
13) Fix potential access past the end of the skb page frag array in
tcp_sendmsg(). From Eric Dumazet.
14) 'skb' can legitimately be NULL in inet{,6}_exact_dif_match(). Fix
from David Ahern.
15) Don't return an error in tcp_sendmsg() if we wronte any bytes
successfully, from Eric Dumazet.
16) Extraneous unlocks in netlink_diag_dump(), we removed the locking
but forgot to purge these unlock calls. From Eric Dumazet.
17) Fix memory leak in error path of __genl_register_family(). We leak
the attrbuf, from WANG Cong.
18) cgroupstats netlink policy table is mis-sized, from WANG Cong.
19) Several XDP bug fixes in mlx5, from Saeed Mahameed.
20) Fix several device refcount leaks in network drivers, from Johan
Hovold.
21) icmp6_send() should use skb dst device not skb->dev to determine L3
routing domain. From David Ahern.
22) ip_vs_genl_family sets maxattr incorrectly, from WANG Cong.
23) We leak new macvlan port in some cases of maclan_common_netlink()
errors. Fix from Gao Feng.
24) Similar to the icmp6_send() fix, icmp_route_lookup() should
determine L3 routing domain using skb_dst(skb)->dev not skb->dev.
Also from David Ahern.
25) Several fixes for route offloading and FIB notification handling in
mlxsw driver, from Jiri Pirko.
26) Properly cap __skb_flow_dissect()'s return value, from Eric Dumazet.
27) Fix long standing regression in ipv4 redirect handling, wrt.
validating the new neighbour's reachability. From Stephen Suryaputra
Lin.
28) If sk_filter() trims the packet excessively, handle it reasonably in
tcp input instead of exploding. From Eric Dumazet.
29) Fix handling of napi hash state when copying channels in sfc driver,
from Bert Kenward.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (121 commits)
mlxsw: spectrum_router: Flush FIB tables during fini
net: stmmac: Fix lack of link transition for fixed PHYs
sctp: change sk state only when it has assocs in sctp_shutdown
bnx2: Wait for in-flight DMA to complete at probe stage
Revert "bnx2: Reset device during driver initialization"
ps3_gelic: fix spelling mistake in debug message
net: ethernet: ixp4xx_eth: fix spelling mistake in debug message
ibmvnic: Fix size of debugfs name buffer
ibmvnic: Unmap ibmvnic_statistics structure
sfc: clear napi_hash state when copying channels
mlxsw: spectrum_router: Correctly dump neighbour activity
mlxsw: spectrum: Fix refcount bug on span entries
bnxt_en: Fix VF virtual link state.
bnxt_en: Fix ring arithmetic in bnxt_setup_tc().
Revert "include/uapi/linux/atm_zatm.h: include linux/time.h"
tcp: take care of truncations done by sk_filter()
ipv4: use new_gw for redirect neigh lookup
r8152: Fix error path in open function
net: bpqether.h: remove if_ether.h guard
net: __skb_flow_dissect() must cap its return value
...
Add new compatible string "brcm,iproc-pcie-paxc-v2" to the iProc PCIe
device tree binding document. "brcm,iproc-pcie-paxc-v2" is for the second
generation of the Broadcom iProc PCIe PAXC host controller.
Update the binding document with more detailed description of each
compatible string and compatible SoCs.
Add description of optional property "msi-map", for use with MSI
controllers with sideband data.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
During enumeration with multi-function EP devices, access to the
configuration space of a non-existent function results in an unsupported
request being returned as expected. By default the PAXB-based iProc PCIe
controller forwards this as an APB error to the host system and that causes
an exception, which is undesired.
Disable this undesired behaviour and let the kernel PCI stack deal with an
access to the non-existent function, in which case a vendor ID of 0xffff is
returned and handled gracefully.
Reported-by: JD Zheng <jiandong.zheng@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: JD Zheng <jiandong.zheng@broadcom.com>
Reviewed-by: Oza Oza <oza.oza@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Pull arch/tile bugfix from Chris Metcalf:
"This just fixes an incompatibility with tile __ro_after_init"
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: handle __ro_after_init like parisc does
Drivers:
- asm9260: fix module autoload
- cmos: fix crashes
- omap: fix clock handling
-----BEGIN PGP SIGNATURE-----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=jG9+
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fixes from Alexandre Belloni:
"Here are a few driver fixes for 4.9. It has been calm for a while so I
don't expect more for this cycle.
Drivers:
- asm9260: fix module autoload
- cmos: fix crashes
- omap: fix clock handling"
* tag 'rtc-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: omap: prevent disabling of clock/module during suspend
rtc: omap: Fix selecting external osc
rtc: cmos: Don't enable interrupts in the middle of the interrupt handler
rtc: cmos: remove all __exit_p annotations
rtc: asm9260: fix module autoload
The iProc PCIe driver is currently using type IPROC_PCIE_PAXB for the
following SoCs: NS, NSP, Cygnus, NS2, and Pegasus. In fact, the BCMA-based
NS uses a legacy PAXB controller that is slightly different from the PAXB
controller used in the rest of SoCs, e.g., some registers are missing and
it does not require software configuration of outbound/inbound address
mapping.
Add a new type, IPROC_PCIE_PAXB_BCMA, to allow us to properly support the
BCMA-based NS along with other iProc-based SoCs going forward.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
During initialization, the current iProc PCIe host driver resets PAXC and
the downstream internal endpoint device that PAXC connects to. If the
endpoint device is already loaded with firmware and has started running
from the bootloader stage, this downstream reset causes the endpoint device
to stop working.
Signed-off-by: Ray Jui <raj.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
The tile architecture already marks RO_DATA as read-only in
the kernel, so grouping RO_AFTER_INIT_DATA with RO_DATA, as is
done by default, means the kernel faults in init when it tries
to write to RO_AFTER_INIT_DATA. For now, just arrange that
__ro_after_init is handled like __write_once, i.e. __read_mostly.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Since commit b45f64d16d ("mlxsw: spectrum_router: Use FIB notifications
instead of switchdev calls") we reflect to the device the entire FIB
table and not only FIBs that point to netdevs created by the driver.
During module removal, FIBs of the second type are removed following
NETDEV_UNREGISTER events sent. The other FIBs are still present in both
the driver's cache and the device's table.
Fix this by iterating over all the FIB tables in the device and flush
them. There's no need to take locks, as we're the only writer.
Fixes: b45f64d16d ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In similar spirit to x86 and arm64 support, add a make_nop_arm()
to replace calls to mcount with a nop in sections that aren't
traced.
Link: http://lkml.kernel.org/r/20161018234200.5804-1-sboyd@codeaurora.org
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The trace_events_file.c filter logic can be a bit complex. I copy this into
a userspace program where I can debug it a bit easier. One issue is the op
is defined in most places as an int instead of as an enum, and gdb just
gives the value when debugging. Having the actual op name shown in gdb is
more useful.
This has no functionality change, but helps in debugging when the file is
debugged in user space.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Currently the filter logic for comparisons (like greater-than and less-than)
are used, they share the same function and a switch statement is used to
jump to the comparison type to perform. This is done in the extreme hot path
of the tracing code, and it does not take much more space to create a
unique comparison function to perform each type of comparison and remove the
switch statement.
Also, a bug was found where the binary and operation for 64 bits could fail
if the resulting bits were greater than 32 bits, because the result was
passed into a 32 bit variable. This was fixed when adding the separate
binary and function.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Use glob_match() to support flexible glob wildcards (*,?)
and character classes ([) for ftrace.
Since the full glob matching is slower than the current
partial matching routines(*pat, pat*, *pat*), this leaves
those routines and just add MATCH_GLOB for complex glob
expression.
e.g.
----
[root@localhost tracing]# echo 'sched*group' > set_ftrace_filter
[root@localhost tracing]# cat set_ftrace_filter
sched_free_group
sched_change_group
sched_create_group
sched_online_group
sched_destroy_group
sched_offline_group
[root@localhost tracing]# echo '[Ss]y[Ss]_*' > set_ftrace_filter
[root@localhost tracing]# head set_ftrace_filter
sys_arch_prctl
sys_rt_sigreturn
sys_ioperm
SyS_iopl
sys_modify_ldt
SyS_mmap
SyS_set_thread_area
SyS_get_thread_area
SyS_set_tid_address
sys_fork
----
Link: http://lkml.kernel.org/r/147566869501.29136.6462645009894738056.stgit@devbox
Acked-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
As the number of iProc PCIe core registers starts to grow and differ
between different revisions of the iProc PCIe controllers, the
current way of populating each individual unsupported register with
value 'IPROC_PCIE_REG_INVALID' with a table entry has become a bit
messy and is difficult to scale up in the future.
Improve the current driver by populating the invalid entries with code
instead of through individual table entries. This helps to avoid a
significant number of invalid table entries when support for the next
revision of the iProc controller is added.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
While it is useful to know which MDIO driver is being registered, demote
the pr_info() to a pr_debug().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 52f95bbfcf ("stmmac: fix adjust link call in case of a switch
is attached") added some logic to avoid polling the fixed PHY and
therefore invoking the adjust_link callback more than once, since this
is a fixed PHY and link events won't be generated.
This works fine the first time, because we start with phydev->irq =
PHY_POLL, so we call adjust_link, then we set phydev->irq =
PHY_IGNORE_INTERRUPT and we stop polling the PHY.
Now, if we called ndo_close(), which calls both phy_stop() and does an
explicit netif_carrier_off(), we end up with a link down. Upon calling
ndo_open() again, despite starting the PHY state machine, we have
PHY_IGNORE_INTERRUPT set, and we generate no link event at all, so the
link is permanently down.
Fixes: 52f95bbfcf ("stmmac: fix adjust link call in case of a switch is attached")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value of function macvlan_addr_busy is used as bool value,
so use bool value instead of integer number "1" and "0".
Signed-off-by: Gao Feng <gfree.wind@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a module is first loaded and its function ip records are added to the
ftrace list of functions to modify, they are set to DISABLED, as their text
is still in a read only state. When the module is fully loaded, and can be
updated, the flag is cleared, and if their's any functions that should be
tracing them, it is updated at that moment.
But there's several locations that do record accounting and should ignore
records that are marked as disabled, or they can cause issues.
Alexei already fixed one location, but others need to be addressed.
Cc: stable@vger.kernel.org
Fixes: b7ffffbb46 "ftrace: Add infrastructure for delayed enabling of module functions"
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
ftrace_shutdown() checks for sanity of ftrace records
and if dyn_ftrace->flags is not zero, it will warn.
It can happen that 'flags' are set to FTRACE_FL_DISABLED at this point,
since some module was loaded, but before ftrace_module_enable()
cleared the flags for this module.
In other words the module.c is doing:
ftrace_module_init(mod); // calls ftrace_update_code() that sets flags=FTRACE_FL_DISABLED
... // here ftrace_shutdown() is called that warns, since
err = prepare_coming_module(mod); // didn't have a chance to clear FTRACE_FL_DISABLED
Fix it by ignoring disabled records.
It's similar to what __ftrace_hash_rec_update() is already doing.
Link: http://lkml.kernel.org/r/1478560460-3818619-1-git-send-email-ast@fb.com
Cc: stable@vger.kernel.org
Fixes: b7ffffbb46 "ftrace: Add infrastructure for delayed enabling of module functions"
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Use DEVICE_ATTR_RW for read-write attributes. This simplifies the source
code, improves readability, and reduces the chance of inconsistencies.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@rw@
declarer name DEVICE_ATTR;
identifier x,x_show,x_store;
@@
DEVICE_ATTR(x, \(0644\|S_IRUGO|S_IWUSR\), x_show, x_store);
@script:ocaml@
x << rw.x;
x_show << rw.x_show;
x_store << rw.x_store;
@@
if not (x^"_show" = x_show && x^"_store" = x_store)
then Coccilib.include_match false
@@
declarer name DEVICE_ATTR_RW;
identifier rw.x,rw.x_show,rw.x_store;
@@
- DEVICE_ATTR(x, \(0644\|S_IRUGO|S_IWUSR\), x_show, x_store);
+ DEVICE_ATTR_RW(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Replace the custom u64_to_ptr() function with the u64_to_user_ptr()
macro.
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when users shutdown a sock with SEND_SHUTDOWN in sctp, even if
this sock has no connection (assoc), sk state would be changed to
SCTP_SS_CLOSING, which is not as we expect.
Besides, after that if users try to listen on this sock, kernel
could even panic when it dereference sctp_sk(sk)->bind_hash in
sctp_inet_listen, as bind_hash is null when sock has no assoc.
This patch is to move sk state change after checking sk assocs
is not empty, and also merge these two if() conditions and reduce
indent level.
Fixes: d46e416c11 ("sctp: sctp should change socket state when shutdown is received")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new helper function could be used by host drivers to get the limitaion
of max link speed provided by DT. If the property isn't assigned or is
invalid, it will return -EINVAL to the caller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Some of the host drivers have the requirement of knowing whether the EP
would never train at some link speed at all. For instance, on some boards,
the link won't train at 5 GT/s but the host driver still sacrifice some
cycles to wait for the result of training at 5 GT/s as the host could
actually support 5 GT/s. So we could parse this new property and make the
host drivers be aware of these cases.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Baoquan He says:
====================
bnx2: Wait for in-flight DMA to complete at probe stage
This is v2 post.
In commit 3e1be7a ("bnx2: Reset device during driver initialization"),
firmware requesting code was moved from open stage to probe stage.
The reason is in kdump kernel hardware iommu need device be reset in
driver probe stage, otherwise those in-flight DMA from 1st kernel
will continue going and look up into the newly created io-page tables.
However bnx2 chip resetting involves firmware requesting issue, that
need be done in open stage.
Michale Chan suggested we can just wait for the old in-flight DMA to
complete at probe stage, then though without device resetting, we
don't need to worry the old in-flight DMA could continue looking up
the newly created io-page tables.
v1->v2:
Michael suggested to wait for the in-flight DMA to complete at probe
stage. So give up the old method of trying to reset chip at probe
stage, take the new way accordingly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In-flight DMA from 1st kernel could continue going in kdump kernel.
New io-page table has been created before bnx2 does reset at open stage.
We have to wait for the in-flight DMA to complete to avoid it look up
into the newly created io-page table at probe stage.
Suggested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3e1be7ad2d.
When people build bnx2 driver into kernel, it will fail to detect
and load firmware because firmware is contained in initramfs and
initramfs has not been uncompressed yet during do_initcalls. So
revert commit 3e1be7a and work out a new way in the later patch.
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>