This function wasn't being called in this particular case when the MC
reboots. This caused resource reallocations to not be handled properly
and often ended up disabling the interface.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is mainly to prepare for a future overlay networking patch that
could cause an MC reset at probe time if the UDP tunnel port list is
set immediately upon driver load.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the csum_level for encapsulated packets where the encapsulation
type, l3 class and l4 class are sets that need it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RX checksum offload of encapsulated packets. This
essentially just means paying attention to the inner checksum flags
in the RX event, and if *either* checksum flag indicates a fail then
don't tell the kernel that checksum offload was successful.
Also, count these checksum errors and export the counts to ethtool -S.
Test the most common "good" case of RX events with a single bitmask
instead of a series of ifs. Move the more specific error checking
in to a separate function for clarity, and don't use unlikely() there
since we know at least one of the bits is bad.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function igmpv3/mld_add_delrec() we allocate pmc and put it in
idev->mc_tomb, so we should free it when we don't need it in del_delrec().
But I removed kfree(pmc) incorrectly in latest two patches. Now fix it.
Fixes: 24803f38a5 ("igmp: do not remove igmp souce list info when ...")
Fixes: 1666d49e1d ("mld: do not remove mld souce list info when ...")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a crash when running out of grant refs when creating many
queues across many netdevs.
* If creating queues fails (i.e. there are no grant refs available),
call xenbus_dev_fatal() to ensure that the xenbus device is set to the
closed state.
* If no queues are created, don't call xennet_disconnect_backend as
netdev->real_num_tx_queues will not have been set correctly.
* If setup_netfront() fails, ensure that all the queues created are
cleaned up, not just those that have been set up.
* If any queues were set up and an error occurs, call
xennet_destroy_queues() to clean up the napi context.
* If any fatal error occurs, unregister and destroy the netdev to avoid
leaving around a half setup network device.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Brüns says:
====================
Fixes for sierra_net driver
When trying to initiate a dual-stack (ipv4v6) connection, a MC7710, FW
version SWI9200X_03.05.24.00ap answers with an unsupported LSI. Add support
for this LSI.
Also the link_type should be ignored when going idle, otherwise the modem
is stuck in a bad link state.
Tested on MC7710, T-Mobile DE, APN internet.telekom, IPv4v6 PDP type. Both
IPv4 and IPv6 connections work.
v2: Do not overwrite protocol field in rx_fixup
v3: Remove leftover struct ethhdr *eth declaration
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the context is deactivated, the link_type is set to 0xff, which
triggers a warning message, and results in a wrong link status, as
the LSI is ignored.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a context is configured as dualstack ("IPv4v6"), the modem indicates
the context activation with a slightly different indication message.
The dual-stack indication omits the link_type (IPv4/v6) and adds
additional address fields.
IPv6 LSIs are identical to IPv4 LSIs, but have a different link type.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
With hopefully most/all users of module.h that were looking for
exception table functions moved over to the new extable.h header,
we can remove the back-compat include that let us transition
without introducing build regressions.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Jessica Yu <jeyu@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files were including module.h for exception table related
functions. We've now separated that content out into its own file
"extable.h" so now move over to that and where possible, avoid all
the extra header content in module.h that we don't really need to
compile these non-modular files.
Note:
init/main.c still needs module.h for __init_or_module
kernel/extable.c still needs module.h for is_module_text_address
...and so we don't get the benefit of removing module.h from the cpp
feed for these two files, unlike the almost universal 1:1 exchange
of module.h for extable.h we were able to do in the arch dirs.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Jessica Yu <jeyu@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Dmitry reported a kernel warning:
WARNING: CPU: 3 PID: 2936 at net/kcm/kcmsock.c:627
kcm_write_msgs+0x12e3/0x1b90 net/kcm/kcmsock.c:627
CPU: 3 PID: 2936 Comm: a.out Not tainted 4.10.0-rc6+ #209
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:15 [inline]
dump_stack+0x2ee/0x3ef lib/dump_stack.c:51
panic+0x1fb/0x412 kernel/panic.c:179
__warn+0x1c4/0x1e0 kernel/panic.c:539
warn_slowpath_null+0x2c/0x40 kernel/panic.c:582
kcm_write_msgs+0x12e3/0x1b90 net/kcm/kcmsock.c:627
kcm_sendmsg+0x163a/0x2200 net/kcm/kcmsock.c:1029
sock_sendmsg_nosec net/socket.c:635 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:645
sock_write_iter+0x326/0x600 net/socket.c:848
new_sync_write fs/read_write.c:499 [inline]
__vfs_write+0x483/0x740 fs/read_write.c:512
vfs_write+0x187/0x530 fs/read_write.c:560
SYSC_write fs/read_write.c:607 [inline]
SyS_write+0xfb/0x230 fs/read_write.c:599
entry_SYSCALL_64_fastpath+0x1f/0xc2
when calling syscall(__NR_write, sock2, 0x208aaf27ul, 0x0ul) on a KCM
seqpacket socket. It appears that kcm_sendmsg() does not handle len==0
case correctly, which causes an empty skb is allocated and queued.
Fix this by skipping the skb allocation for len==0 case.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 90c311b0ee ("xen-netfront: Fix Rx stall during network
stress and OOM") caused the refill timer to be triggerred almost on
all invocations of xennet_alloc_rx_buffers for certain workloads.
This reworks the fix by reverting to the old behaviour and taking into
consideration the skb allocation failure. Refill timer is now triggered
on insufficient requests or skb allocation failure.
Signed-off-by: Vineeth Remanan Pillai <vineethp@amazon.com>
Fixes: 90c311b0ee (xen-netfront: Fix Rx stall during network stress and OOM)
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Postpone axis initialization to the first open instead of doing it
in joydev_connect. This is to make sure the generated startup events
are representative of the current joystick state rather than what
it was when joydev_connect() was called, potentially much earlier.
Once the first user is connected to joydev node we'll be updating
joydev->abs[] values and subsequent clients will be getting correct
initial states as well.
This solves issues with joystick driven menus that start scrolling
up each time they are started, until the user moves the joystick to
generate events. In emulator menu setups where the menu program is
restarted every time the game exits, the repeated need to move the
joystick to stop the unintended scrolling gets old rather quickly...
Signed-off-by: Raphael Assenat <raph@raphnet.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull SCSI target fixes from Nicholas Bellinger:
"This target series for v4.10 contains fixes which address a few
long-standing bugs that DATERA's QA + automation teams have uncovered
while putting v4.1.y target code into production usage.
We've been running the top three in our nightly automated regression
runs for the last two months, and the COMPARE_AND_WRITE fix Mr. Gary
Guo has been manually verifying against a four node ESX cluster this
past week.
Note all of them have CC' stable tags.
Summary:
- Fix a bug with ESX EXTENDED_COPY + SAM_STAT_RESERVATION_CONFLICT
status, where target_core_xcopy.c logic was incorrectly returning
SAM_STAT_CHECK_CONDITION for all non SAM_STAT_GOOD cases (Nixon
Vincent)
- Fix a TMR LUN_RESET hung task bug while other in-flight TMRs are
being aborted, before the new one had been dispatched into tmr_wq
(Rob Millner)
- Fix a long standing double free OOPs, where a dynamically generated
'demo-mode' NodeACL has multiple sessions associated with it, and
the /sys/kernel/config/target/$FABRIC/$WWN/ subsequently disables
demo-mode, but never converts the dynamic ACL into a explicit ACL
(Rob Millner)
- Fix a long standing reference leak with ESX VAAI COMPARE_AND_WRITE
when the second phase WRITE COMMIT command fails, resulting in
CHECK_CONDITION response never being sent and se_cmd->cmd_kref
never reaching zero (Gary Guo)
Beyond these items on v4.1.y we've reproduced, fixed, and run through
our regression test suite using iscsi-target exports, there are two
additional outstanding list items:
- Remove a >= v4.2 RCU conversion BUG_ON that would trigger when
dynamic node NodeACLs where being converted to explicit NodeACLs.
The patch drops the BUG_ON to follow how pre RCU conversion worked
for this special case (Benjamin Estrabaud)
- Add ibmvscsis target_core_fabric_ops->max_data_sg_nent assignment
to match what IBM's Virtual SCSI hypervisor is already enforcing at
transport layer. (Bryant Ly + Steven Royer)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
ibmvscsis: Add SGL limit
target: Fix COMPARE_AND_WRITE ref leak for non GOOD status
target: Fix multi-session dynamic se_node_acl double free OOPs
target: Fix early transport_generic_handle_tmr abort scenario
target: Use correct SCSI status during EXTENDED_COPY exception
target: Don't BUG_ON during NodeACL dynamic -> explicit conversion
The Generic PHY drivers gets assigned after we checked that the current
PHY driver is NULL, so we need to check a few things before we can
safely dereference d->driver. This would be causing a NULL deference to
occur when a system binds to the Generic PHY driver. Update
phy_attach_direct() to do the following:
- grab the driver module reference after we have assigned the Generic
PHY drivers accordingly, and remember we came from the generic PHY
path
- update the error path to clean up the module reference in case the
Generic PHY probe function fails
- split the error path involving phy_detacht() to avoid double free/put
since phy_detach() does all the clean up
- finally, have phy_detach() drop the module reference count before we
call device_release_driver() for the Generic PHY driver case
Fixes: cafe8df8b9 ("net: phy: Fix lack of reference count on PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the latest series of ThinkPads, the button events for the TrackPoint
are reported through the touchpad itself as opposed to the TrackPoint
device. In order to report these buttons properly, we need to forward
them to the TrackPoint device and notify psmouse to send the button
presses/releases.
Signed-off-by: Lyude Paul <thatslyude@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch does several cleanup changes to F30 code
- switch to using BIT() macro
- use DIV_ROUND_UP() where appropriate
- factor out code setting up and reporting buttons
- use single loop when reporting buttons: arithmetic is cheap compared to
conditionals and associated branch misprediction.
Tested-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of using custom method of "passing" extended buttons from the
touchpad to trackstick, let's switch to the newly introduced SERIO_OOB_DATA
channel.
Tested-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=uxqv
-----END PGP SIGNATURE-----
Merge tag 'pstore-v4.10-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore fix from Kees Cook:
"Fix pstore regression (boot Oops) when ftrace disabled, from Brian
Norris"
* tag 'pstore-v4.10-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
pstore: don't OOPS when there are no ftrace zones
Pull input fixes from Dmitry Torokhov:
"A fix for a crash in uinput, and a fix for build errors when HID-RMI
is built-in but SERIO is a module"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - select 'SERIO' when needed
Input: uinput - fix crash when mixing old and new init style
We'll OOPS in ramoops_get_next_prz() if the platform didn't ask for any
ftrace zones (i.e., cxt->fprzs will be NULL). Let's just skip this
entire FTRACE section if there's no 'fprzs'.
Regression seen on a coreboot/depthcharge-based Chromebook.
Fixes: 2fbea82bbb ("pstore: Merge per-CPU ftrace records into one")
Cc: Joel Fernandes <joelaf@google.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
The tracksticks on the Lenovo thinkpads have their buttons connected
through the touchpad device. We already fixed that in synaptics.c, but
when we switch the device into RMI4 mode to have proper support, the
pass-through functionality can't deal with them easily.
We add a new PS/2 flag and protocol designed for psmouse. The RMI4 F03
pass-through can then emit a special set of commands to notify psmouse the
state of the buttons.
This patch implements the protocol in psmouse, while an other will
do the same for rmi4-f03.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The deamon through which the kernel module communicates with the userspace
part of Orangefs, the "client-core", sends initialization data to the
kernel module with ioctl. The initialization data was built by the
client-core in a 2k buffer and copy_from_user'd into a 1k buffer
in the kernel module. When more than 1k of initialization data needed
to be sent, some was lost, reducing the usability of the control by which
debug levels are set. This patch sets the kernel side buffer to 2K to
match the userspace side...
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
This patch is simlar to one Dan Carpenter sent me, cleans
up some return codes and whitespace errors. There was one
place where he thought inserting an error message into
the ring buffer might be too chatty, I hope I convinced him
othewise. As a consolation <g> I changed a truly chatty
error message in another location into a debug message,
system-admins had already yelled at me about that one...
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Instead we submit the discard requests and use another workqueue to
release the extents from the extent busy list.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Sort busy extents by the full block number instead of just the AGNO so
that we can issue consecutive discard requests that the block layer could
merge (although we'll need additional block layer fixes for fast devices).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
- Fix regression in attaching groups to existing container for
SPAPR IOMMU backend (Alexey Kardashevskiy)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=iCg7
-----END PGP SIGNATURE-----
Merge tag 'vfio-v4.10-final' of git://github.com/awilliam/linux-vfio
Pull VFIO fix from Alex Williamson:
"Fix regression in attaching groups to existing container for SPAPR
IOMMU backend (Alexey Kardashevskiy)"
* tag 'vfio-v4.10-final' of git://github.com/awilliam/linux-vfio:
vfio/spapr_tce: Set window when adding additional groups to container
To address new warnings emmited by gcc 7, e.g.::
CC /tmp/build/perf/util/intel-pt-decoder/intel-pt-pkt-decoder.o
CC /tmp/build/perf/tests/parse-events.o
util/intel-pt-decoder/intel-pt-pkt-decoder.c: In function 'intel_pt_pkt_desc':
util/intel-pt-decoder/intel-pt-pkt-decoder.c:499:6: error: this statement may fall through [-Werror=implicit-fallthrough=]
if (!(packet->count))
^
util/intel-pt-decoder/intel-pt-pkt-decoder.c:501:2: note: here
case INTEL_PT_CYC:
^~~~
CC /tmp/build/perf/util/intel-pt-decoder/intel-pt-decoder.o
cc1: all warnings being treated as errors
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-mf0hw789pu9x855us5l32c83@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Pull ARM fixes from Russell King:
"A couple more fixes for 4.10:
- fix addressing the short regset write issue (Dave Martin)
- fix for LPAE systems which leave a pending imprecise data abort
before entering the kernel (Alexander Sverdlin)"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8643/3: arm/ptrace: Preserve previous registers for short regset write
ARM: 8642/1: LPAE: catch pending imprecise abort on unmask
Set the timeout for TCP connections to be 1 lease period to ensure
that we don't lose our lease due to a faulty TCP connection.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Rather than doing a module request from within the init function, add
a soft dependency on the available IOMMU backend drivers. This makes
the dependency visible to userspace when picking modules for the
ram disk.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When the NFSv4 server tells us the lease period, we usually want
to adjust down the timeout parameters on the TCP connection to
ensure that we don't miss lease renewals due to a faulty connection.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Currently we force the log and simply try again if we hit a busy extent,
but especially with online discard enabled it might take a while after
the log force for the busy extents to disappear, and we might have
already completed our second pass.
So instead we add a new waitqueue and a generation counter to the pag
structure so that we can do wakeups once we've removed busy extents,
and we replace the single retry with an unconditional one - after
all we hold the AGF buffer lock, so no other allocations or frees
can be racing with us in this AG.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
We don't just need the structure to track busy extents which can be
avoided with a synchronous transaction, but also to keep track of
pending discard.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
If pag cannot be allocated, the current error exit path will trip
a null pointer deference error when calling xfs_buf_hash_destroy
with a null pag. Fix this by adding a new error exit labels and
jumping to those accordingly, avoiding the hash destroy and
unnecessary kmem_free on pag.
Up to three things need to be properly unwound:
1) pag memory allocation
2) xfs_buf_hash_init
3) radix_tree_insert
For any given iteration through the loop, any of the above which
succeed must be unwound for /this/ pag, and then all prior
initialized pags must be unwound.
Addresses-Coverity-Id: 1397628 ("Dereference after null check")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bill O'Donnell <billodo@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
We're changing both metadata and data, so we need to update the
timestamps for clone operations. Dedupe on the other hand does
not change file data, and only changes invisible metadata so the
timestamps should not be updated.
This follows existing btrfs behavior.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
[darrick: remove redundant is_dedupe test]
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The SPE architecture requires each exception level to enable access
to the SPE controls for the exception level below it, since additional
context-switch logic may be required to handle the buffer safely.
This patch allows EL1 (host) access to the SPE controls when entered at
EL2.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that we have a workaround for Hisilicon erratum 161010101, notes
this in the arm64 silicon-errata document.
The new config option is too long to fit in the existing kconfig column,
so this is widened to accomodate it. At the same time, an existing
whitespace error is corrected, and the existing pattern of a line space
between vendors is enforced for recent additions.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
[Mark: split patch, reword commit message, rework table]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Addressing a few cases spotted by a new warning in gcc 7:
tests/parse-events.c: In function 'test_pmu_events':
tests/parse-events.c:1790:39: error: '%s' directive output may be truncated writing up to 255 bytes into a region of size 90 [-Werror=format-truncation=]
snprintf(name, MAX_NAME, "cpu/event=%s/u", ent->d_name);
^~
In file included from /usr/include/stdio.h:939:0,
from /git/linux/tools/perf/util/map.h:9,
from /git/linux/tools/perf/util/symbol.h:7,
from /git/linux/tools/perf/util/evsel.h:10,
from tests/parse-events.c:3:
/usr/include/bits/stdio2.h:64:10: note: '__builtin___snprintf_chk' output between 13 and 268 bytes into a destination of size 100
return __builtin___snprintf_chk (__s, __n, __USE_FORTIFY_LEVEL - 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
__bos (__s), __fmt, __va_arg_pack ());
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
tests/parse-events.c:1798:29: error: '%s' directive output may be truncated writing up to 255 bytes into a region of size 100 [-Werror=format-truncation=]
snprintf(name, MAX_NAME, "%s:u,cpu/event=%s/u", ent->d_name, ent->d_name);
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Fixes: 945aea220b ("perf tests: Move test objects into 'tests' directory")
Link: http://lkml.kernel.org/n/tip-ty4q2p8zp1dp3mskvubxskm5@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Addressing this warning from gcc 7:
CC /tmp/build/perf/bench/numa.o
bench/numa.c: In function '__bench_numa':
bench/numa.c:1582:42: error: '%d' directive output may be truncated writing between 1 and 10 bytes into a region of size between 8 and 17 [-Werror=format-truncation=]
snprintf(tname, 32, "process%d:thread%d", p, t);
^~
bench/numa.c:1582:25: note: directive argument in the range [0, 2147483647]
snprintf(tname, 32, "process%d:thread%d", p, t);
^~~~~~~~~~~~~~~~~~~~
In file included from /usr/include/stdio.h:939:0,
from bench/../util/util.h:47,
from bench/../builtin.h:4,
from bench/numa.c:11:
/usr/include/bits/stdio2.h:64:10: note: '__builtin___snprintf_chk' output between 17 and 35 bytes into a destination of size 32
return __builtin___snprintf_chk (__s, __n, __USE_FORTIFY_LEVEL - 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
__bos (__s), __fmt, __va_arg_pack ());
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Petr Holasek <pholasek@redhat.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-twa37vsfqcie5gwpqwnjuuz9@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The pclk is necessary for zx2967 I2S controller. the driver
currently doesn't handle it. This is something we need to fix.
In turn, the driver supports zx296718's I2S controller.
By the way, this patch also change the clock name from tx to wclk
to make it clear.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ZTE's zx2967 I2S controller driver introduces pclk, this
patch documents this fact.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes the condition where the controller has not fully completed its
final transfer and leaves the bus and controller in a undesirable state.
At the end of the last transmitted byte, the existing driver would just
signal for a STOP condition to be transmitted then immediately signal
completion. However, the full STOP procedure might not have fully taken
place by the time the runtime PM shuts off the peripheral clock, leaving
the bus in a suspended state.
Alternatively, the STOP condition on the bus may have completed, but when
the next transaction is requested by the upper layer, not all the
necessary register cleanup was finished from the last transfer which made
the driver return BUS BUSY when it really wasn't.
This patch now makes all transmit and receive transactions wait for the
STOP condition to fully complete before signaling a completed transaction.
With this new method, runtime PM no longer seems to be an issue.
Fixes: 310c18a414 ("i2c: riic: add driver")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix the following sparse warnings:
drivers/edac/fsl_ddr_edac.c:148:1: warning:
symbol 'dev_attr_inject_data_hi' was not declared. Should it be static?
drivers/edac/fsl_ddr_edac.c:150:1: warning:
symbol 'dev_attr_inject_data_lo' was not declared. Should it be static?
drivers/edac/fsl_ddr_edac.c:152:1: warning:
symbol 'dev_attr_inject_ctrl' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170209150424.15124-1-weiyj.lk@gmail.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Intel Gemini Lake has the same SMBus host controller than Intel Broxton.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
