- Add Daniel Thompson as Maintainer.
- Add new files
- Shift Jingoo down the list due to a lack of time.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Adds some trace points showing input compressed stream or
output decoded frame information.
Adds an unconditional trace point when streaming starts showing
the compressed stream and the decoded frame information.
Adds an unconditional trace point at instance closure summarizing
into a single line the decoding process (stream information, decoded
and output frames number, potential errors observed).
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds support of DELTA MJPEG video decoder back-end,
implemented by calling JPEG_DECODER_HW0 firmware
using RPMSG IPC communication layer.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
EOS (End Of Stream) support allows user to get
all the potential decoded frames remaining in decoder
pipeline after having reached the end of video bitstream.
To do so, user calls VIDIOC_DECODER_CMD(V4L2_DEC_CMD_STOP)
which will drain the decoder and get the drained frames
that are then returned to user.
User is informed of EOS completion in two ways:
- dequeue of an empty frame flagged to V4L2_BUF_FLAG_LAST
- reception of a V4L2_EVENT_EOS event.
If, unfortunately, no buffer is available on CAPTURE queue
to return the empty frame, EOS is delayed till user queue
one CAPTURE buffer.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
IPC (Inter Process Communication) support for communication with
DELTA coprocessor firmware using rpmsg kernel framework.
Based on 4 services open/set_stream/decode/close and their associated
rpmsg messages.
The messages structures are duplicated on both host and firmware
side and are packed (use only of 32 bits size fields in messages
structures to ensure packing).
Each service is synchronous; service returns only when firmware
acknowledges the associated command message.
Due to significant parameters size exchanged from host to copro,
parameters are not inserted in rpmsg messages. Instead, parameters are
stored in physical memory shared between host and coprocessor.
Memory is non-cacheable, so no special operation is required
to ensure memory coherency on host and on coprocessor side.
Multi-instance support and re-entrance are ensured using host_hdl and
copro_hdl in message header exchanged between both host and coprocessor.
This avoids to manage tables on both sides to get back the running context
of each instance.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Helper functions used by decoder back-ends to allocate
physically contiguous memory required by hardware video
decoder.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
For debugging and testing it is useful to see the converted alias
string. Add support to perf stat/record and perf list to print the alias
conversion. The text string is saved in the alias structure. For perf
stat/record it is folded into the normal -v. For perf list -v was taken,
so we use --debug.
Before:
% perf list
...
cache:
l1d.replacement
[L1D data line replacements]
l1d_pend_miss.fb_full
[Cycles a demand request was blocked due to Fill Buffers inavailability]
After
% perf list --debug
...
cache:
l1d.replacement
[L1D data line replacements]
cpu/umask=0x1,period=2000003,event=0x51/
l1d_pend_miss.fb_full
[Cycles a demand request was blocked due to Fill Buffers inavailability]
cpu/umask=0x2,period=2000003,cmask=1,event=0x48/
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/20170128020345.19007-6-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The code for handling pmu aliases without specifying the PMU hardcoded
only supported the cpu PMU.
This patch extends it to work for all PMUs. We always duplicate the
event for all PMUs that have an matching alias. This allows to
automatically expand an alias for all instances of a PMU (so for example
you can monitor all cache boxes with a single event)
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/20170128020345.19007-5-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add support for registering json aliases per PMU. Any alias with an unit
matching the prefix is registered to the PMU. Uncore has multiple
instances of most units, so all these aliases get registered for each
individual PMU (this is important later to run the event on every
instance of the PMU).
To avoid printing the events multiple times in perf list filter out
duplicated events during printing.
v2: Rely on uncore_ prefix already in unit
v3: Document why calls were reordered
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/20170128020345.19007-4-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Handle the "Unit" field, which is needed to find the right PMU for an
event. We call it "pmu" and convert it to the perf pmu name with an
uncore prefix.
Handle the "ExtSel" field, which just extends the event mask with an
additional bit.
Handle the "Filter" field which adds parameters to the main event
to configure filtering.
Handle the "Unit" field which declares the unit the values should be
scaled too (similar to what the kernel exports)
Set up the "perpkg" field for uncore events so that perf knows they are
per package (similar to what the kernel exports)
Then output the fields into the pmu-events data structures which are
compiled into perf.
Filter out zero fields, except for the event itself.
v2: Fix compilation. Add uncore_ prefix at pre-processing time.
Move eventcode change to separate patch.
v3: Remove extra __maybe_unused
v4: dont duplicate aliases for cpu pmu events
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/20170128020345.19007-3-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The next patch needs to modify event code. Previously eventcode was just
passed through as a string. Now parse it as a number.
v2: Don't special case 0
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/20170128020345.19007-2-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
These two debug messages are missing the trailing newline.
Signed-off-by: He Kuang <hekuang@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Bintian Wang <bintian.wang@huawei.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20170207073412.26983-2-hekuang@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Since HAVE_KPROBES can be enabled in arm64, this patch introduces
regs_query_register_offset() to convert register name to offset for
arm64, so the BPF prologue feature is ready to use.
Signed-off-by: He Kuang <hekuang@huawei.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Bintian Wang <bintian.wang@huawei.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20170207073412.26983-1-hekuang@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When a sequencer queue is created in snd_seq_queue_alloc(),it adds the
new queue element to the public list before referencing it. Thus the
queue might be deleted before the call of snd_seq_queue_use(), and it
results in the use-after-free error, as spotted by syzkaller.
The fix is to reference the queue object at the right time.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On some newer boards using mkbp we're hooking up non-matrix buttons and
switches to the EC but NOT to the main application processor.
Let's add kernel support to handle this. Rather than creating a whole
new input driver, we'll continue to use cros_ec_keyb and just report the
new keys.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We're using non-canonical addresses in drm_mm, and we're making sure that
userspace is using canonical addressing - both in case of softpin
(verifying incoming offset) and when relocating (converting to canonical
when updating offset returned to userspace).
Unfortunately when considering the need for relocations, we're comparing
offset from userspace (in canonical form) with drm_mm node (in
non-canonical form), and as a result, we end up always relocating if our
offsets are in the "problematic" range.
Let's always convert the offsets to avoid the performance impact of
relocations.
Fixes: a5f0edf63b ("drm/i915: Avoid writing relocs with addresses in non-canonical form")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Reported-by: Michał Pyrzowski <michal.pyrzowski@intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207195559.18798-1-michal.winiarski@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 038c95a313)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The goal of the WARN was to catch when we are still actively using the
fence as we go into the runtime suspend. However, the reg->pin_count is
too coarse as it does not distinguish between exclusive ownership of the
fence register from activity.
I've not improved on the WARN, nor have we captured this WARN in an
exact igt, but it is showing up regularly in the wild:
[ 1915.935332] WARNING: CPU: 1 PID: 10861 at drivers/gpu/drm/i915/i915_gem.c:2022 i915_gem_runtime_suspend+0x116/0x130 [i915]
[ 1915.935383] WARN_ON(reg->pin_count)[ 1915.935399] Modules linked in:
snd_hda_intel i915 drm_kms_helper vgem netconsole scsi_transport_iscsi fuse vfat fat x86_pkg_temp_thermal coretemp intel_cstate intel_uncore snd_hda_codec_hdmi snd_hda_codec_generic snd_hda_codec snd_hwdep snd_hda_core snd_pcm snd_timer snd mei_me mei serio_raw intel_rapl_perf intel_pch_thermal soundcore wmi acpi_pad i2c_algo_bit syscopyarea sysfillrect sysimgblt fb_sys_fops drm r8169 mii video [last unloaded: drm_kms_helper]
[ 1915.935785] CPU: 1 PID: 10861 Comm: kworker/1:0 Tainted: G U W 4.9.0-rc5+ #170
[ 1915.935799] Hardware name: LENOVO 80MX/Lenovo E31-80, BIOS DCCN34WW(V2.03) 12/01/2015
[ 1915.935822] Workqueue: pm pm_runtime_work
[ 1915.935845] ffffc900044fbbf0 ffffffffac3220bc ffffc900044fbc40 0000000000000000
[ 1915.935890] ffffc900044fbc30 ffffffffac059bcb 000007e6044fbc60 ffff8801626e3198
[ 1915.935937] ffff8801626e0000 0000000000000002 ffffffffc05e5d4e 0000000000000000
[ 1915.935985] Call Trace:
[ 1915.936013] [<ffffffffac3220bc>] dump_stack+0x4f/0x73
[ 1915.936038] [<ffffffffac059bcb>] __warn+0xcb/0xf0
[ 1915.936060] [<ffffffffac059c4f>] warn_slowpath_fmt+0x5f/0x80
[ 1915.936158] [<ffffffffc052d916>] i915_gem_runtime_suspend+0x116/0x130 [i915]
[ 1915.936251] [<ffffffffc04f1c74>] intel_runtime_suspend+0x64/0x280 [i915]
[ 1915.936277] [<ffffffffac0926f1>] ? dequeue_entity+0x241/0xbc0
[ 1915.936298] [<ffffffffac36bb85>] pci_pm_runtime_suspend+0x55/0x180
[ 1915.936317] [<ffffffffac36bb30>] ? pci_pm_runtime_resume+0xa0/0xa0
[ 1915.936339] [<ffffffffac4514e2>] __rpm_callback+0x32/0x70
[ 1915.936356] [<ffffffffac451544>] rpm_callback+0x24/0x80
[ 1915.936375] [<ffffffffac36bb30>] ? pci_pm_runtime_resume+0xa0/0xa0
[ 1915.936392] [<ffffffffac45222d>] rpm_suspend+0x12d/0x680
[ 1915.936415] [<ffffffffac69f6d7>] ? _raw_spin_unlock_irq+0x17/0x30
[ 1915.936435] [<ffffffffac0810b8>] ? finish_task_switch+0x88/0x220
[ 1915.936455] [<ffffffffac4534bf>] pm_runtime_work+0x6f/0xb0
[ 1915.936477] [<ffffffffac074353>] process_one_work+0x1f3/0x4d0
[ 1915.936501] [<ffffffffac074678>] worker_thread+0x48/0x4e0
[ 1915.936523] [<ffffffffac074630>] ? process_one_work+0x4d0/0x4d0
[ 1915.936542] [<ffffffffac074630>] ? process_one_work+0x4d0/0x4d0
[ 1915.936559] [<ffffffffac07a2c9>] kthread+0xd9/0xf0
[ 1915.936580] [<ffffffffac07a1f0>] ? kthread_park+0x60/0x60
[ 1915.936600] [<ffffffffac69fe62>] ret_from_fork+0x22/0x30
In the case the register is pinned, it should be present and we will
need to invalidate them to be restored upon resume as we cannot expect
the owner of the pin to call get_fence prior to use after resume.
Fixes: 7c108fd8fe ("drm/i915: Move fence cancellation to runtime suspend")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98804
Reported-by: Lionel Landwerlin <lionel.g.landwerlin@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Imre Deak <imre.deak@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.10-rc1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170203125717.8431-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit e0ec3ec698)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add the missing INTEL_OUTPUT_DP_MST case in bxt_get_dpll()
to correctly initialize the crtc_state and port plls when
link training a DP MST monitor on BXT/APL devices.
Fixes: a277ca7dc0 ("drm/i915: Split bxt_ddi_pll_select()")
Bugs: https://bugs.freedesktop.org/show_bug.cgi?id=99572
Reviewed-by: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Gary C Wang <gary.c.wang@intel.com>
Reviewed-by: Ciobanu, Nathan D <nathan.d.ciobanu@intel.com>
Reviewed-by: Herbert, Marc <marc.herbert@intel.com>
Reviewed-by: Bride, Jim <jim.bride@intel.com>
Reviewed-by: Navare, Manasi D <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Lee, Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1486096329-6255-1-git-send-email-shawn.c.lee@intel.com
(cherry picked from commit 0aab2c721d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This fixes a race condition that may occur whenever ST micro busy end
interrupt is raised just after being unmasked but before leaving mmci
interrupt context.
A dead-lock has been found if connecting mmci ST Micro variant whose amba
id is 0x10480180 to some new eMMC that supports internal caches. Whenever
mmci driver enables cache control by programming eMMC's EXT_CSD register,
block driver may request to flush the eMMC internal caches causing mmci
driver to send a MMC_SWITCH command to the card with FLUSH_CACHE operation.
And because busy end interrupt may be mistakenly cleared while not yet
processed, this mmc request may never complete. As a result, mmcqd task
may be stuck forever.
Here is an instance caught by lockup detector which shows that mmcqd task
was hung while waiting for mmc_flush_cache command to complete:
..
[ 240.251595] INFO: task mmcqd/1:52 blocked for more than 120 seconds.
[ 240.257973] Not tainted 4.1.13-00510-g9d91424 #2
[ 240.263109] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.270955] mmcqd/1 D c047504c 0 52 2 0x00000000
[ 240.277359] [<c047504c>] (__schedule) from [<c04754a0>] (schedule+0x40/0x98)
[ 240.284418] [<c04754a0>] (schedule) from [<c0477d40>] (schedule_timeout+0x148/0x188)
[ 240.292191] [<c0477d40>] (schedule_timeout) from [<c0476040>] (wait_for_common+0xa4/0x170)
[ 240.300491] [<c0476040>] (wait_for_common) from [<c02efc1c>] (mmc_wait_for_req_done+0x4c/0x13c)
[ 240.309224] [<c02efc1c>] (mmc_wait_for_req_done) from [<c02efd90>] (mmc_wait_for_cmd+0x64/0x84)
[ 240.317953] [<c02efd90>] (mmc_wait_for_cmd) from [<c02f5b14>] (__mmc_switch+0xa4/0x2a8)
[ 240.325964] [<c02f5b14>] (__mmc_switch) from [<c02f5d40>] (mmc_switch+0x28/0x30)
[ 240.333389] [<c02f5d40>] (mmc_switch) from [<c02f0984>] (mmc_flush_cache+0x54/0x80)
[ 240.341073] [<c02f0984>] (mmc_flush_cache) from [<c02ff0c4>] (mmc_blk_issue_rq+0x114/0x4e8)
[ 240.349459] [<c02ff0c4>] (mmc_blk_issue_rq) from [<c03008d4>] (mmc_queue_thread+0xc0/0x180)
[ 240.357844] [<c03008d4>] (mmc_queue_thread) from [<c003cf90>] (kthread+0xdc/0xf4)
[ 240.365339] [<c003cf90>] (kthread) from [<c0010068>] (ret_from_fork+0x14/0x2c)
..
..
[ 240.664311] INFO: task partprobe:564 blocked for more than 120 seconds.
[ 240.670943] Not tainted 4.1.13-00510-g9d91424 #2
[ 240.676078] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.683922] partprobe D c047504c 0 564 486 0x00000000
[ 240.690318] [<c047504c>] (__schedule) from [<c04754a0>] (schedule+0x40/0x98)
[ 240.697396] [<c04754a0>] (schedule) from [<c0477d40>] (schedule_timeout+0x148/0x188)
[ 240.705149] [<c0477d40>] (schedule_timeout) from [<c0476040>] (wait_for_common+0xa4/0x170)
[ 240.713446] [<c0476040>] (wait_for_common) from [<c01f3300>] (submit_bio_wait+0x58/0x64)
[ 240.721571] [<c01f3300>] (submit_bio_wait) from [<c01fbbd8>] (blkdev_issue_flush+0x60/0x88)
[ 240.729957] [<c01fbbd8>] (blkdev_issue_flush) from [<c010ff84>] (blkdev_fsync+0x34/0x44)
[ 240.738083] [<c010ff84>] (blkdev_fsync) from [<c0109594>] (do_fsync+0x3c/0x64)
[ 240.745319] [<c0109594>] (do_fsync) from [<c000ffc0>] (ret_fast_syscall+0x0/0x3c)
..
Here is the detailed sequence showing when this issue may happen:
1) At probe time, mmci device is initialized and card busy detection based
on DAT[0] monitoring is enabled.
2) Later during run time, since card reported to support internal caches, a
MMCI_SWITCH command is sent to eMMC device with FLUSH_CACHE operation. On
receiving this command, eMMC may enter busy state (for a relatively short
time in the case of the dead-lock).
3) Then mmci interrupt is raised and mmci_irq() is called:
MMCISTATUS register is read and is equal to 0x01000440. So the following
status bits are set:
- MCI_CMDRESPEND (= 6)
- MCI_DATABLOCKEND (= 10)
- MCI_ST_CARDBUSY (= 24)
Since MMCIMASK0 register is 0x3FF, status variable is set to 0x00000040 and
BIT MCI_CMDRESPEND is cleared by writing MMCICLEAR register.
Then mmci_cmd_irq() is called. Considering the following conditions:
- host->busy_status is 0,
- this is a "busy response",
- reading again MMCISTATUS register gives 0x1000400,
MMCIMASK0 is updated to unmask MCI_ST_BUSYEND bit.
Thus, MMCIMASK0 is set to 0x010003FF and host->busy_status is set to wait
for busy end completion.
Back again in status loop of mmci_irq(), we quickly go through
mmci_data_irq() as there are no data in that case. And we finally go
through following test at the end of while(status) loop:
/*
* Don't poll for busy completion in irq context.
*/
if (host->variant->busy_detect && host->busy_status)
status &= ~host->variant->busy_detect_flag;
Because status variable is not yet null (is equal to 0x40), we do not leave
interrupt context yet but we loop again into while(status) loop. So we run
across following steps:
a) MMCISTATUS register is read again and this time is equal to 0x01000400.
So that following bits are set:
- MCI_DATABLOCKEND (= 10)
- MCI_ST_CARDBUSY (= 24)
Since MMCIMASK0 register is equal to 0x010003FF:
b) status variable is set to 0x01000000.
c) MCI_ST_CARDBUSY bit is cleared by writing MMCICLEAR register.
Then, mmci_cmd_irq() is called one more time. Since host->busy_status is
set and that MCI_ST_CARDBUSY is set in status variable, we just return from
this function.
Back again in mmci_irq(), status variable is set to 0 and we finally leave
the while(status) loop. As a result we leave interrupt context, waiting for
busy end interrupt event.
Now, consider that busy end completion is raised IN BETWEEN steps 3.a) and
3.c). In such a case, we may mistakenly clear busy end interrupt at step
3.c) while it has not yet been processed. This will result in mmc command
to wait forever for a busy end completion that will never happen.
To fix the problem, this patch implements the following changes:
Considering that the mmci seems to be triggering the IRQ on both edges
while monitoring DAT0 for busy completion and that same status bit is used
to monitor start and end of busy detection, special care must be taken to
make sure that both start and end interrupts are always cleared one after
the other.
1) Clearing of card busy bit is moved in mmc_cmd_irq() function where
unmasking of busy end bit is effectively handled.
2) Just before unmasking busy end event, busy start event is cleared by
writing card busy bit in MMCICLEAR register.
3) Finally, once we are no more busy with a command, busy end event is
cleared writing again card busy bit in MMCICLEAR register.
This patch has been tested with the ST Accordo5 machine, not yet supported
upstream but relies on the mmci driver.
Signed-off-by: Sarang Mairal <sarang.mairal@garmin.com>
Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add the defines for the new buttons and switches connected to the CrosEC.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Apparently there are machines out there with Skylake CPU and KabyPoint
PCH. Judging from our driver code, there doesn't seem to be any code
paths that would do anything different between SunrisePoint and
KabyPoint PCHs, so it would seem okay to accept the combo without
warnings.
Fixes: 22dea0be50 ("drm/i915: Introduce Kabypoint PCH for Kabylake H/DT.")
References: https://lists.freedesktop.org/archives/intel-gfx/2017-February/118611.html
Reported-by: Rainer Koenig <Rainer.Koenig@ts.fujitsu.com>
Cc: Rainer Koenig <Rainer.Koenig@ts.fujitsu.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: <stable@vger.kernel.org> # v4.8+
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485956769-26015-1-git-send-email-jani.nikula@intel.com
(cherry picked from commit 3aac4acb89)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Commit 920cf41949 ("drm/i915: Introduce an internal allocator for
disposable private objects") introduced a regression for the kernel
running as Xen dom0: when switching to graphics mode a GPU HANG
occurred.
Reason seems to be a missing adaption similar to that done in
commit 7453c549f5 ("swiotlb: Export swiotlb_max_segment to users")
to i915_gem_object_get_pages_internal().
So limit the maximum page order to be used according to the maximum
swiotlb segment size instead to the complete swiotlb size.
Fixes: 920cf41949 ("drm/i915: Introduce an internal allocator for disposable private objects")
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202094711.939-1-jgross@suse.com
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.10-rc1+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 5584f1b1d7)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On a non-llc system, the objects are created with .cache_level =
CACHE_NONE and so the transition to uncached for scanout is a no-op.
However, if the object was never written to, it will still be in the CPU
domain (having been zeroed out by shmemfs). Those cachelines need to be
flushed prior to display.
Reported-and-tested-by: Vito Caputo
Fixes: a6a7cc4b7d ("drm/i915: Always flush the dirty CPU cache when pinning the scanout")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.10-rc1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170109111932.6342-1-chris@chris-wilson.co.uk
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 69aeafeae9)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When we send a deauth to a station we don't know about, we
need to use the PROBE_RESP queue. This can happen when we
send a deauth to a station that is not associated to us.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When NSSN is behind the reorder buffer due to timeout
the reorder timer isn't getting re-armed until NSSN
catches up. Fix it.
Fixes: 0690405fef ("iwlwifi: mvm: add reorder timeout per frame")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode, first_agg_queue is initialized to
IWL_MVM_DQA_MIN_DATA_QUEUE. This causes two bugs in the tx response
flow:
1. When TX fails, we set IEEE80211_TX_STAT_AMPDU_NO_BACK regardless
if we actually have aggregation open on the queue. This causes
mac80211 to send a BAR frame even though there is no aggregation
open.
Fix that by simply checking the AMPDU flag that is set on by
mac80211 for AMPDU packets.
2. When reclaiming frames in aggregation mode, we reclaim based on
scheduler ssn and not the SN.
The reason is that scheduler ssn may be ahead of SN due to a hole
in the BA window that was filled.
However, if we have aggregations open on IWL_MVM_DQA_BSS_CLIENT_QUEUE
the reclaim flow will still go to the code of non-aggregation
instead of the aggregation code since IWL_MVM_DQA_BSS_CLIENT_QUEUE
is smaller than IWL_MVM_DQA_MIN_DATA_QUEUE, although it is a valid
aggregation queue.
Fix that by always using the aggregation reclaim code by default in
DQA mode (currently it is implicitly used by default for all queues
except the reserved BSS queue).
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Handling of the number of space time streams was missing for HT rate in
rate printing function. Fix it.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When getting RF_KILL and disabling radio, the device gets stopped
and reset. This erases the IVAR table that matches the interrupt
to its cause, and is essential for MSIX proper functionality.
Till now, the table wasn't re-configured after the reset, and
therefore the interrupt that enabled radio didn't fire on the
right irq, and the driver didn't handle it correctly.
To fix this, configure the IVAR table again after resetting the
device.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During the suspend/resume flow some HW blocks are reset. This causes
the IVAR table to be completely erased. This table is where interrupt
causes are bound to specific IRQs. When the table is empty the
interrupt handlers are not called correctly. Fix this by reconfiguring
the IVAR table after resume.
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The MSIX configuration flow includes two different stages:
configuring the HW by writing to the IVAR table and configuring the SW
to reflect the HW configuration.
The HW configuration is needed on each HW reset,
whereas the SW configuration is only needed during the init flow.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Always use printk_deferred() in printk_safe_flush_line().
Flushing can be done from NMI or printk_safe contexts (when
we are in panic), so we can't call console drivers, yet still
want to store the messages in the logbuf buffer. Therefore we
use a deferred printk version.
Link: http://lkml.kernel.org/r/20170206164253.GA463@tigerII.localdomain
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Tejun Heo <tj@kernel.org>
Cc: Calvin Owens <calvinowens@fb.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Suggested-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This patch extends the idea of NMI per-cpu buffers to regions
that may cause recursive printk() calls and possible deadlocks.
Namely, printk() can't handle printk calls from schedule code
or printk() calls from lock debugging code (spin_dump() for instance);
because those may be called with `sem->lock' already taken or any
other `critical' locks (p->pi_lock, etc.). An example of deadlock
can be
vprintk_emit()
console_unlock()
up() << raw_spin_lock_irqsave(&sem->lock, flags);
wake_up_process()
try_to_wake_up()
ttwu_queue()
ttwu_activate()
activate_task()
enqueue_task()
enqueue_task_fair()
cfs_rq_of()
task_of()
WARN_ON_ONCE(!entity_is_task(se))
vprintk_emit()
console_trylock()
down_trylock()
raw_spin_lock_irqsave(&sem->lock, flags)
^^^^ deadlock
and some other cases.
Just like in NMI implementation, the solution uses a per-cpu
`printk_func' pointer to 'redirect' printk() calls to a 'safe'
callback, that store messages in a per-cpu buffer and flushes
them back to logbuf buffer later.
Usage example:
printk()
printk_safe_enter_irqsave(flags)
//
// any printk() call from here will endup in vprintk_safe(),
// that stores messages in a special per-CPU buffer.
//
printk_safe_exit_irqrestore(flags)
The 'redirection' mechanism, though, has been reworked, as suggested
by Petr Mladek. Instead of using a per-cpu @print_func callback we now
keep a per-cpu printk-context variable and call either default or nmi
vprintk function depending on its value. printk_nmi_entrer/exit and
printk_safe_enter/exit, thus, just set/celar corresponding bits in
printk-context functions.
The patch only adds printk_safe support, we don't use it yet.
Link: http://lkml.kernel.org/r/20161227141611.940-4-sergey.senozhatsky@gmail.com
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Tejun Heo <tj@kernel.org>
Cc: Calvin Owens <calvinowens@fb.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
A preparation patch for printk_safe work. No functional change.
- rename nmi.c to print_safe.c
- add `printk_safe' prefix to some (which used both by printk-safe
and printk-nmi) of the exported functions.
Link: http://lkml.kernel.org/r/20161227141611.940-3-sergey.senozhatsky@gmail.com
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Tejun Heo <tj@kernel.org>
Cc: Calvin Owens <calvinowens@fb.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
vprintk(), just like printk(), better be using per-cpu printk_func
instead of direct vprintk_emit() call. Just in case if vprintk()
will ever be called from NMI, or from any other context that can
deadlock in printk().
Link: http://lkml.kernel.org/r/20161227141611.940-2-sergey.senozhatsky@gmail.com
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Tejun Heo <tj@kernel.org>
Cc: Calvin Owens <calvinowens@fb.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Fix rebase breakage from commit 55dd00a73a ("KVM: x86: add
KVM_HC_CLOCK_PAIRING hypercall", 2017-01-24), courtesy of the
"I could have sworn I had pushed the right branch" department.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Update the drivers to pass the RSSI level as a cfg80211_cqm_rssi_notify
parameter and pass this value to userspace in a new nl80211 attribute.
This helps both userspace and also helps in the implementation of the
multiple RSSI thresholds CQM mechanism.
Note for marvell/mwifiex I pass 0 for the RSSI value because the new
RSSI value is not available to the driver at the time of the
cfg80211_cqm_rssi_notify call, but the driver queries the new value
immediately after that, so it is actually available just a moment later
if we wanted to defer caling cfg80211_cqm_rssi_notify until that moment.
Without this, the new cfg80211 code (patch 3) will call .get_station
which will send a duplicate HostCmd_CMD_RSSI_INFO command to the hardware.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend ieee80211_cqm_rssi_notify with a rssi_level parameter so that
this information can be passed to netlink clients in the next patch, if
available. Most drivers will have this value at hand. wl1251 receives
events from the firmware that only tell it whether latest measurement
is above or below threshold so we don't pass any value at this time
(parameter is 0).
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I and Sergey would like to volunteer as printk code maintainers.
It is a code that everyone is using, various people fix bugs or
even add features but there is nobody really interested into
maintaining it.
I and Sergey have put a lot of effort into understanding the code
and related problems. We are working on solutions for some long
term problems. There is a nice summary from the Kernel Summit
presentation, see https://lwn.net/Articles/705938/
We have already started to use the gained knowledge and comment
on other printk-related patches. The official role should help
us to do it more effectively.
Our priorities are:
+ prevent deadlocks (printk_safe patchset, console locks)
+ prevent softlocks (async printk, console_sem and flushing)
+ handle other bugs/fixes/features as they come
with this in mind:
+ printk is used in different context
+ need special care in some modes, e.g. oops, panic, suspend
+ do best effort to store/show messages
+ the code is already pretty complicated and twisted;
support clean ups; always think hard if a feature/fix
is worth any complication
Of course, it still will be much appreciated if other people review
printk patches.
Regarding the workflow. It will be highly appreciated if the patches
might still go via Andrew's -mm tree at least for 4.10. In the long
term, we would like to make Andrew's life easier and handle printk
patches in an own git tree. But we first need to set it up and get
familiar with the processes.
Link: http://lkml.kernel.org/r/1481798878-31898-1-git-send-email-pmladek@suse.com
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
For wowlan netdetect a separate limit is defined for the number of
matchsets. Currently, this limit is ignored and the regular limit
for scheduled scan matchsets, ie. struct wiphy::max_match_sets, is
used for the net-detect case as well.
Cc: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the benefit of drivers that rebuild IEs in firmware, parse the
IEs for HT/VHT capabilities and the respective membership selector
in the (extended) supported rates. This avoids duplicating the same
code into all drivers that need this information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid assigning rdev to NULL when we already have it and getting it
again from the wiphy index, by moving this code to relevant if block.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
kmalloc() can fail. Also let's move the allocation out of the
declaration block so it's easier to read.
Fixes: 4a5eccaa93 ("mac80211: Show pending txqlen in debugfs.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This merges in a fix which touches both PPC and KVM code,
which was therefore put into a topic branch in the powerpc
tree.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Instead of open coding the CMAC algorithm in the mac80211 driver using
byte wide xors and calls into the crypto layer for each block of data,
instantiate a cmac(aes) synchronous hash and pass all the data into it
directly. This does not only simplify the code, it also allows the use
of more efficient and more secure implementations, especially on
platforms where SIMD ciphers have a considerable setup cost.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
