This patch replaces several identical frame drop
paths with a single shared rx frame error handler.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patches "rt2x00: Improve TX status entry validation" and "rt2x00: rework tx
status handling in rt2800pci" together were causing problems with tx status
processing in rt2800pci:
phy1 -> rt2800pci_txdone: Warning - Got TX status for an empty queue 3, dropping
phy1 -> rt2800pci_txdone: Warning - Got TX status for an unavailable queue 7, dropping
Fix this by using the correct field definition for getting the QID out of the
tx status report.
Reported-by: Luis Correia <luis.f.correia@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Tested-by: Luis Correia <luis.f.correia@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to initialize qidx to zero as it will ever be
overwritten by the correct value.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is an error condition that is not supposed to happen. Hence, it is
safe to add unlikely to this check.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since no skb will be mapped for RX and TX at the same time we can
simply shortcut the check for SKBDESC_DMA_MAPPED_TX.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates IEEE802.11 mesh constants to be consistent with newly
approved values. It modifies some values, as well as adds many new constants
in preparation for updating mesh code to the current 802.11s drafts. ANA
numbers were taken from:
https://mentor.ieee.org/802.11/dcn/09/11-09-0031-12-0000-ana-database-assigned-number-authority.xls
A few notes are in order:
1. This will break backwards compatibility with existing Linux kernels as
over-the-air constants have changed.
2. Some old and obsolete constants have been retained for now as the mesh code
itself hasn't been updated yet to the new 802.11s draft. This was desired to
keep the existing mesh scheme working until it can be updated. Adding the
approved values is the first step in updating the mesh code.
3. Obsolete constants have been clearly marked.
4. All ANA approved 802.11s constants have been added.
Signed-off-by: Steve deRosier <steve@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Results for the active channel are updated whenever a new survey dump
is requested, the old data is kept to allow multiple processes to
make their own channel utilization averages.
All other channels only contain the data for the last time that the
hardware was on the channel, i.e. the last scan result or other
off-channel activity.
Running a background scan does not clear the data for the active
channel.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This prevents random memory corruption if the number of channels ever gets
changed without an update to the internal channel array size.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using these, user space can calculate a relative channel utilization
with arbitrary intervals by regularly taking snapshots of the survey
results.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Several serve threading problems in the current
release reorder timer implementation have been
discovered.
A lengthy discussion - which lists some of the
pitfalls and possible solutions - can be found at:
http://marc.info/?t=128635927000001
But due to the complicated nature of the subject and
the imminent advent of a new -rc cycle, it was
decided to disable the feature for the time being.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch not only fixes a null-pointer de-reference
that would be triggered by a PLINK_OPEN frame with mis-
matching/incompatible mesh configuration, but also
responds correctly to non-compatible PLINK_OPEN frames
by generating a PLINK_CLOSE with the right reason code.
The original bug was detected by smatch.
( http://repo.or.cz/w/smatch.git )
net/mac80211/mesh_plink.c +574 mesh_rx_plink_frame(168)
error: we previously assumed 'sta' could be null.
Cc: <stable@kernel.org>
Reviewed-and-Tested-by: Steve deRosier <steve@cozybit.com>
Reviewed-and-Tested-by: Javier Cardona <javier@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of keeping track of wraparound, clear the counters on every
access and keep separate deltas for ANI and later survey use.
Also moves the function for calculating the 'listen time' for ANI
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise, if there is an AP and a STATION, and AP
is removed, the NIC will not revert back to STATION mode.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some stats for /proc/net/wireless (and wext in general) are not
being set. This patch addresses a few of those with values easily
obtained from mac80211 core.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Old messages didn't mention the device in question.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need to export io_tlb_overflow_buffer. I'll remove
io_tlb_overflow_buffer completely in the long term though.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This reverts commit 5a254ffe3f.
The commit failed to take into account that allocated wireless devices
(wiphys) are not added into the device list upon allocation, but only
when they are registered. Therefore, it opened up a race between
allocating and registering a name, so that if two processes allocate and
register concurrently ("alloc, alloc, register, register" rather than
"alloc, register, alloc, register") the code will attempt to use the
same name twice.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stanse found that pch_gbe_xmit_frame uses skb after it is freed. Fix
that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Masayuki Ohtake <masa-korg@dsn.okisemi.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanse found that i2400m_rx frees skb, but still uses skb->len even
though it has skb_len defined. So use skb_len properly in the code.
And also define it unsinged int rather than size_t to solve
compilation warnings.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: linux-wimax@intel.com
Acked-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanse found that ia_init_one locks a spinlock and inside of that it
calls ia_start which calls:
* request_irq
* tx_init which does kmalloc(GFP_KERNEL)
Both of them can thus sleep and result in a deadlock. I don't see a
reason to have a per-device spinlock there which is used only there
and inited right before the lock location. So remove it completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanse found that mpc_push frees skb and then it dereferences it. It
is a typo, new_skb should be dereferenced there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanse found we do in console_show:
kfree_skb(skb);
return skb->len;
which is not good. Fix that by remembering the len and use it in the
function instead.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The omap2plus_defconfig doesn't boot up when built with CONFIG_PM
disabled on the latest linux-omap master. Below are the observations
1. OMAP3 reboots in the middle of boot
--------------------------------------------------
[ 0.000000] Calibrating delay loop... 494.72 BogoMIPS (lpj=1933312)
[ 0.000000] pid_max: default: 32768 minimum: 301
[ 0.000000] Security Framework initialized
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] Brought up 1 CPUs
[ 0.000000] SMP: Total of 1 processors activated (494.72 BogoMIPS).
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
U-Boot 1.1.4 (Feb 11 2009 - 16:10:23)
OMAP3430-GP rev 2, CPU-OPP2 L3-165MHz
TI 3430SDP 1.0 Version + mDDR (Boot NOR)
DRAM: 128 MB
Flash: 128 MB
NAND:128 MiB
--------------------------------------------------
2. OMAP4 does a kernel PANIC
-------------------------------------
[ 0.000000] Calibrating delay loop... 1195.29 BogoMIPS (lpj=4669440)
[ 0.000000] pid_max: default: 32768 minimum: 301
[ 0.000000] Security Framework initialized
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] L310 cache controller enabled
[ 0.000000] l2x0: 16 ways, CACHE_ID 0x410000c2, AUX_CTRL 0x0e050000
[ 0.000000] CPU1: Booted secondary processor
[ 0.000000] Brought up 2 CPUs
[ 0.000000] SMP: Total of 2 processors activated (2395.78 BogoMIPS).
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
[ 0.000000] mux: Could not set signal i2c2_scl.i2c2_scl
[ 0.000000] mux: Could not set signal i2c2_sda.i2c2_sda
[ 0.000000] mux: Could not set signal i2c3_scl.i2c3_scl
[ 0.000000] mux: Could not set signal i2c3_sda.i2c3_sda
[ 0.000000] mux: Could not set signal i2c4_scl.i2c4_scl
[ 0.000000] mux: Could not set signal i2c4_sda.i2c4_sda
-------------------------------------
This is happening because 'omap_serial_init()' is hanging in the boot.
On OMAP3 the watchdog is generating reboot because devices_init doesn't
happens where as on OMAP4 it just hangs without reboot.
The uart clock is not getting enabled after omap_device_idle as part
of omap_serial_init.
The omap_device_idle(will disable the clock) then omap_uart_block_sleep()
should enable clock back disabled during the boot up phase.
But omap_uart_block_sleep() stuffed version is binded only under
CONFIG_PM and other version is just empty. Hence it is not enabling
clock back as expected
This patch adds uart clock enable code to omap_uart_block_sleep() function
built with CONFIG_PM disabled.
Thanks to Charulatha and Govindraj for their help on this debug.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is duplicate cleanup code in the init and exit functions. Now,
oprofile_arch_exit() is also used if oprofile_arch_init() fails.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
This patch simplifies op_create_counter(). Removing if/else if paths
and return code variable by direct returning from function.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
This patch removes some unnecessary goto statements.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
This patch fixes a resource leak on failure, where the
oprofilefs and some counters may not released properly.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: <stable@kernel.org> # .35.x
LKML-Reference: <20100929145225.GJ13563@erda.amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
kbuild: fix oldnoconfig to do the right thing
kconfig: Temporarily disable dependency warnings
kconfig: delay symbol direct dependency initialization
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
IPS driver: Fix limit clamping when reducing CPU power
[PATCH 2/2] IPS driver: disable CPU turbo
IPS driver: apply BIOS provided CPU limit if different from default
intel_ips -- ensure we do not enable gpu turbo mode without driver linkage
intel_ips: Print MCP limit exceeded values.
IPS driver: verify BIOS provided limits
IPS driver: don't toggle CPU turbo on unsupported CPUs
NULL pointer might be used in ips_monitor()
Release symbol on error-handling path of ips_get_i915_syms()
old_cpu_power is wrongly divided by 65535 in ips_monitor()
seqno mask of THM_ITV register is 16bit
Commit 914bab936fe0388a529079679e2f137aa4ff548d (OMAP: mach-omap2: Fix
incorrect assignment warnings) changed a pointer from 'u32 *' to
'void *' without also fixing up the pointer arithmetic.
Fix the scratchpad offsets so they are byte offsets instead of
word offsets and thus work correctly with a void pointer base.
Special thanks to Jean Pihet for taking the time track down this
problem and propose an initial solution.
Tested with off-idle and off-suspend on 36xx/Zoom3 and 34xx/omap3evm.
Cc: Manjunath Kondaiah G <manjugk@ti.com>
Reported-by: Jean Pihet <jean.pihet@newoldbits.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Jean Pihet <jean.pihet@newoldbits.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When a new dst is used to send a frame, neigh_resolve_output() tries to
associate an struct hh_cache to this dst, calling neigh_hh_init() with
the neigh rwlock write locked.
Most of the time, hh_cache is already known and linked into neighbour,
so we find it and increment its refcount.
This patch changes the logic so that we call neigh_hh_init() with
neighbour lock read locked only, so that fast path can be run in
parallel by concurrent cpus.
This brings part of the speedup we got with commit c7d4426a98
(introduce DST_NOCACHE flag) for non cached dsts, even for cached ones,
removing one of the contention point that routers hit on multiqueue
enabled machines.
Further improvements would need to use a seqlock instead of an rwlock to
protect neigh->ha[], to not dirty neigh too often and remove two atomic
ops.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we've got a generic perf-events based oprofile backend we might
as well make use of it seeing as SH doesn't do anything special with its
oprofile backend. Also introduce a new CONFIG_HW_PERF_EVENTS symbol so
that we can fallback to using the timer interrupt for oprofile if the
CPU doesn't support perf events.
Also, to avoid a section mismatch warning we need to annotate
oprofile_arch_exit() with an __exit marker.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Move the perf-events backend from arch/arm/oprofile into
drivers/oprofile so that the code can be shared between architectures.
This allows each architecture to maintain only a single copy of the PMU
accessor functions instead of one for both perf and OProfile. It also
becomes possible for other architectures to delete much of their
OProfile code in favour of the common code now available in
drivers/oprofile/oprofile_perf.c.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
In preparation for moving the majority of this oprofile code into an
architecture-neutral place separate the architecture-independent code
into oprofile_perf_init() and oprofile_perf_exit().
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
In preparation for moving the generic functions out of this file, give
the functions more general names (e.g. remove "arm" from the names).
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Make op_name_from_perf_id() global so that we have a way for each
architecture to construct an oprofile name for op->cpu_type. We need to
remove the argument from the function prototype so that we can hide all
implementation details inside the function.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Introduce perf_pmu_name() helper function that returns the name of the
pmu. This gives us a generic way to get the name of a pmu regardless of
how an architecture identifies it internally.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>