Async notifications other than link status are possible in certain
configurations. Remove the BUG_ON in the mcc completion processing path.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ONLINE registers can return 0xFFFFFFFF on more than one
occassion. On systems that care, reading these registers could
lead to problems.
So the new code decides that the ASIC has encountered and error
by reading the UE_STATUS_LOW/HIGH registers. AND them with
the mask values and a non-zero result indicates an error.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrong packet statistics for multicast Rx was causing net-snmp error messages
every 15 seconds. Instead of picking the multicast stats from hardware,
now maintain it in the driver itself.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__alloc_skb() uses a memset() to clear all the beginning of skb,
including bitfields contained in 'flags1' & 'flags2'.
We dont need any more to use kmemcheck_annotate_bitfield() on these
fields. However, we still need it for the clone part, which is not
cleared.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct tulip_private is a bit large (order-1 allocation even on 32bit
arch), try to shrink it, remove its net_device_stats field.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation for recent changes to the tunables accept_ra and
forwarding.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to accepting router advertisement, the IPv6 stack does not send router
solicitations if forwarding is enabled.
This patch enables this behavior to be overruled by setting forwarding to the
special value 2.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current IPv6 behavior is to not accept router advertisements while
forwarding, i.e. configured as router.
This does make sense, a router is typically not supposed to be auto
configured. However there are exceptions and we should allow the
current behavior to be overwritten.
Therefore this patch enables the user to overrule the "if forwarding
enabled then don't listen to RAs" rule by setting accept_ra to the
special value of 2.
An alternative would be to ignore the forwarding switch alltogether
and solely accept RAs based on the value of accept_ra. However, I
found that if not intended, accepting RAs as a router can lead to
strange unwanted behavior therefore we it seems wise to only do so
if the user explicitely asks for this behavior.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The trackpad speaks a similar, but different, protocol from the magic
mouse. However, only small code tweaks here and there are needed to make
basic multitouch work.
Extra logic is required for single-touch emulation of the touchpad. The
changes made here take the approach that only one finger may emulate the
single pointer when multiple fingers have touched the screen. Once that
finger is raised, all touches must be raised before any further single
touch events can be sent.
Sometimes the magic trackpad sends two distinct touch reports as one big
report. Simply splitting the packet in two and resending them through
magicmouse_raw_event ensures they are handled properly.
I also added myself to the copyright statement.
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Michael Poole <mdpoole@troilus.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The new format should be easier to read to determine which bits
correspond to which data. It also brings all the manipulation logic to
the top of the function. This makes size and orientation reading more
clear.
Note that the impetus for this change is the forthcoming support for the
Magic Trackpad, which has a different touch data protocol.
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Michael Poole <mdpoole@troilus.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When converting a lock, an lkb is in the granted state and also being used
to request a new state. In the case that the conversion was a "try 1cb"
type which has failed, and if the new state was incompatible with the old
state, a callback was being generated to the requesting node. This is
incorrect as callbacks should only be sent to all the other nodes holding
blocking locks. The requesting node should receive the normal (failed)
response to its "try 1cb" conversion request only.
This was discovered while debugging a performance problem on GFS2, however
this fix also speeds up GFS as well. In the GFS2 case the performance gain
is over 10x for cases of write activity to an inode whose glock is cached
on another, idle (wrt that glock) node.
(comment added, dct)
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Tested-by: Abhijith Das <adas@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
In xfs_vn_fiemap, we set bvm_count to fi_extent_max + 1 and want
to return fi_extent_max extents, but actually it won't work for
a sparse file. The reason is that in xfs_getbmap we will
calculate holes and set it in 'out', while out is malloced by
bmv_count(fi_extent_max+1) which didn't consider holes. So in the
worst case, if 'out' vector looks like
[hole, extent, hole, extent, hole, ... hole, extent, hole],
we will only return half of fi_extent_max extents.
This patch add a new parameter BMV_IF_NO_HOLES for bvm_iflags.
So with this flags, we don't use our 'out' in xfs_getbmap for
a hole. The solution is a bit ugly by just don't increasing
index of 'out' vector. I felt that it is not easy to skip it
at the very beginning since we have the complicated check and
some function like xfs_getbmapx_fix_eof_hole to adjust 'out'.
Cc: Dave Chinner <david@fromorbit.com>
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Only the first feature request is required to put the Magic Mouse into
multitouch mode. This is also the case for the Magic Trackpad, for which
support will be added in a later commit.
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Michael Poole <mdpoole@troilus.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
DMA is set to use burst mode also for source channel. It should
descrease memory bandwidth needs.
DMA synchronization is set to use prefetch mechanism. SHAM block is behind
L4 bus and it doesn't have fifo. SHAM block is stalling as long as the new
data is available. It takes time to fetch data from memory and transfer it
via L4 bus. With prefetch enabled, data is waiting in DMA fifo and SHAM block
receives new data block faster.
This increases SHA processing speed up to 30 percent depending on the
bus / memory load.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
parallel_data->queue is a percpu pointer but was missing __percpu markup.
Add it.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add no-get quirk for eGalax touch controller to avoid timeout at probe.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch revive ak4642_snd_controls which was removed on
f0fba2ad1b
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This re-adds the lost chunk in commit 9b861528a8.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Haicheng Li <haicheng.li@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <20100903090407.GA19771@localhost>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix kernel-doc notation in linux/mutex.h and kernel/mutex.c,
then add these 2 files to the kernel-locking docbook as the
Mutex API reference chapter.
Add one API function to mutex-design.txt and correct a typo in
that file.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <20100902154816.6cc2f9ad.randy.dunlap@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The explicit saving and restoring of %ebx was confusing stack
unwind data consumers, and it is plain unnecessary to do this
within the asm(), since that was only introduced for PIC user
mode consumers of the original _syscall3() macro this was
derived from.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Arnd Bergmann <arnd@arndb.de>
LKML-Reference: <4C7FBC660200007800013F95@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
... plus additionally introduce {push,pop}f{l,q}_cfi. All in the
hope that the code becomes better readable this way (it gets
quite a bit smaller in any case).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Alexander van Heukelum <heukelum@fastmail.fm>
LKML-Reference: <4C7FBDA40200007800013FAF@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When these stubs are actual functions (i.e. having a return
instruction) and have stack manipulation instructions in them,
they should also be annotated to allow unwinding through them.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Alexander van Heukelum <heukelum@fastmail.fm>
LKML-Reference: <4C7FBCF00200007800013F99@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
... making the code a little less fragile.
Also use pushq_cfi instead of raw CFI annotations in two more
places, and add two missing annotations after stack pointer
adjustments which got modified here anyway.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Alexander van Heukelum <heukelum@fastmail.fm>
LKML-Reference: <4C7FBACF0200007800013F6A@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As this isn't an exception or interrupt entry point, it doesn't
have any of the hardware provide frame layouts active.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Alexander van Heukelum <heukelum@fastmail.fm>
LKML-Reference: <4C7FBAA80200007800013F67@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With the return address removed from the stack, these should
really refer to their caller's register state.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Alexander van Heukelum <heukelum@fastmail.fm>
LKML-Reference: <4C7FBA3D0200007800013F61@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When the PMU is enabled it is valid to have unhandled nmis, two
events could trigger 'simultaneously' raising two back-to-back
NMIs. If the first NMI handles both, the latter will be empty
and daze the CPU.
The solution to avoid an 'unknown nmi' massage in this case was
simply to stop the nmi handler chain when the PMU is enabled by
stating the nmi was handled. This has the drawback that a) we
can not detect unknown nmis anymore, and b) subsequent nmi
handlers are not called.
This patch addresses this. Now, we check this unknown NMI if it
could be a PMU back-to-back NMI. Otherwise we pass it and let
the kernel handle the unknown nmi.
This is a debug log:
cpu #6, nmi #32333, skip_nmi #32330, handled = 1, time = 1934364430
cpu #6, nmi #32334, skip_nmi #32330, handled = 1, time = 1934704616
cpu #6, nmi #32335, skip_nmi #32336, handled = 2, time = 1936032320
cpu #6, nmi #32336, skip_nmi #32336, handled = 0, time = 1936034139
cpu #6, nmi #32337, skip_nmi #32336, handled = 1, time = 1936120100
cpu #6, nmi #32338, skip_nmi #32336, handled = 1, time = 1936404607
cpu #6, nmi #32339, skip_nmi #32336, handled = 1, time = 1937983416
cpu #6, nmi #32340, skip_nmi #32341, handled = 2, time = 1938201032
cpu #6, nmi #32341, skip_nmi #32341, handled = 0, time = 1938202830
cpu #6, nmi #32342, skip_nmi #32341, handled = 1, time = 1938443743
cpu #6, nmi #32343, skip_nmi #32341, handled = 1, time = 1939956552
cpu #6, nmi #32344, skip_nmi #32341, handled = 1, time = 1940073224
cpu #6, nmi #32345, skip_nmi #32341, handled = 1, time = 1940485677
cpu #6, nmi #32346, skip_nmi #32347, handled = 2, time = 1941947772
cpu #6, nmi #32347, skip_nmi #32347, handled = 1, time = 1941949818
cpu #6, nmi #32348, skip_nmi #32347, handled = 0, time = 1941951591
Uhhuh. NMI received for unknown reason 00 on CPU 6.
Do you have a strange power saving mode enabled?
Dazed and confused, but trying to continue
Deltas:
nmi #32334 340186
nmi #32335 1327704
nmi #32336 1819 <<<< back-to-back nmi [1]
nmi #32337 85961
nmi #32338 284507
nmi #32339 1578809
nmi #32340 217616
nmi #32341 1798 <<<< back-to-back nmi [2]
nmi #32342 240913
nmi #32343 1512809
nmi #32344 116672
nmi #32345 412453
nmi #32346 1462095 <<<< 1st nmi (standard) handling 2 counters
nmi #32347 2046 <<<< 2nd nmi (back-to-back) handling one
counter nmi #32348 1773 <<<< 3rd nmi (back-to-back)
handling no counter! [3]
For back-to-back nmi detection there are the following rules:
The PMU nmi handler was handling more than one counter and no
counter was handled in the subsequent nmi (see [1] and [2]
above).
There is another case if there are two subsequent back-to-back
nmis [3]. The 2nd is detected as back-to-back because the first
handled more than one counter. If the second handles one counter
and the 3rd handles nothing, we drop the 3rd nmi because it
could be a back-to-back nmi.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
[ renamed nmi variable to pmu_nmi to avoid clash with .nmi in entry.S ]
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: peterz@infradead.org
Cc: gorcunov@gmail.com
Cc: fweisbec@gmail.com
Cc: ying.huang@intel.com
Cc: ming.m.lin@intel.com
Cc: eranian@google.com
LKML-Reference: <1283454469-1909-3-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
During testing of a patch to stop having the perf subsytem
swallow nmis, it was uncovered that Nehalem boxes were randomly
getting unknown nmis when using the perf tool.
Moving the ack'ing of the PMI closer to when we get the status
allows the hardware to properly re-set the PMU bit signaling
another PMI was triggered during the processing of the first
PMI. This allows the new logic for dealing with the
shortcomings of multiple PMIs to handle the extra NMI by
'eat'ing it later.
Now one can wonder why are we getting a second PMI when we
disable all the PMUs in the begining of the NMI handler to
prevent such a case, for that I do not know. But I know the fix
below helps deal with this quirk.
Tested on multiple Nehalems where the problem was occuring.
With the patch, the code now loops a second time to handle the
second PMI (whereas before it was not).
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: peterz@infradead.org
Cc: robert.richter@amd.com
Cc: gorcunov@gmail.com
Cc: fweisbec@gmail.com
Cc: ying.huang@intel.com
Cc: ming.m.lin@intel.com
Cc: eranian@google.com
LKML-Reference: <1283454469-1909-2-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next:
drm/nv50: initialize ramht_refs list for faked 0 channel
drm/nouveau: Don't take struct_mutex around the pushbuf IOCTL.
drm/nouveau: Take fence spinlock before reading the last sequence.
It is forbidden to call input_free_device() after input_unregister_device().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Once device is registered we should call input_unregister_device()
instead of input_free_device().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We call platform_get_drvdata() in tps6507x_ts_remove(),
thus we should call platform_set_drvdata() in tps6507x_ts_probe().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use input_free_device() to free devices that have not been registered.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If we attempt to preallocate more than 2^32 blocks of space in a
single syscall, the transaction block reservation will overflow
leading to a hangs in the superblock block accounting code. This
is trivially reproduced with xfs_io. Fix the problem by capping the
allocation reservation to the maximum number of blocks a single
xfs_bmapi() call can allocate (2^21 blocks).
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
fresh skbs have ip_summed set to CHECKSUM_NONE (0)
We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.
Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.
Change most occurrences of :
skb->ip_summed = CHECKSUM_NONE;
by :
skb_checksum_none_assert(skb);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_RCU_CPU_STALL_VERBOSE depends on CONFIG_TREE_PREEMPT_RCU, but
rcu_bootup_announce_oddness() complains if CONFIG_RCU_CPU_STALL_VERBOSE
is not set even in the case of CONFIG_TREE_RCU. This commit therefore
fixes rcu_bootup_announce_oddness() to avoid insisting on impossibilities.
Reported-by: Guy Martin <gmsoft@tuxicoman.be>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
We need it for PFIFO_INTR_CACHE_ERROR interrupt handling,
because nouveau_fifo_swmthd looks for matching gpuobj in
ramht_refs list.
It fixes kernel panic in nouveau_gpuobj_ref_find.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We don't need it and it can lead to lock order inversions with respect
to drm_global_mutex, potentially causing dead locks.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It fixes a race between the TTM delayed work queue and the GEM IOCTLs
(fdo bug 29583) uncovered by the BKL removal.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The max depth supported by T3 is 64K entries. This fixes a bug
introduced in commit 9918b28d ("RDMA/cxgb3: Increase the max CQ
depth") that causes stalls and possibly crashes in large MPI clusters.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
GCC warns about empty printf format strings, and after
the addition of %pV these existing such cases in the
scsi driver layer were exposed enough for the compiler
to start seeing them.
Based almost entirely upon a patch by Joe Perches.
[jejb: fix up sym53c8xx msg]
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fixes a lockdep warning:
[ 516.287584] =========================================================
[ 516.288386] [ INFO: possible irq lock inversion dependency detected ]
[ 516.288386] 2.6.35b #7
[ 516.288386] ---------------------------------------------------------
[ 516.288386] swapper/0 just changed the state of lock:
[ 516.288386] (&qdisc_tx_lock){+.-...}, at: [<c12eacda>] est_timer+0x62/0x1b4
[ 516.288386] but this lock took another, SOFTIRQ-unsafe lock in the past:
[ 516.288386] (est_tree_lock){+.+...}
[ 516.288386]
[ 516.288386] and interrupts could create inverse lock ordering between them.
...
So, est_tree_lock needs BH protection because it's taken by
qdisc_tx_lock, which is used both in BH and process contexts.
(Full warning with this patch at netdev, 02 Sep 2010.)
Fixes commit: ae638c47dc
("pkt_sched: gen_estimator: add a new lock")
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
warning: zero-length gnu_printf format string
Fix the above warning by inserting a space into the literal string.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The doorbell reset initially appears to work correctly,
the controller resets, comes up, some i/o can even be
done, but on at least some Smart Arrays in some servers,
it eventually causes a subsequent controller lockup due
to some kind of PCIe error, and kdump can end up leaving
the root filesystem in an unbootable state. For this
reason, until the problem is fixed, or at least isolated
to certain hardware enough to be avoided, the doorbell
reset should not be used at all.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The current code in tree has problems with Login.
This patch fixes the Login Failure .
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
[mnc: Can't believe I missed that.]
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>