According to RFC4303, section "3.3.3. Sequence Number Generation",
the first packet sent using a given SA will contain a sequence
number of 1.
This is applicable to both ESN and non-ESN mode, which was not covered
in commit mentioned in Fixes line.
Fixes: 3d42c8cc67 ("net/mlx5e: Ensure that IPsec sequence packet number starts from 1")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
All packet offloads SAs have reqid in it to make sure they have
corresponding policy. While it is not strictly needed for transparent
mode, it is extremely important in tunnel mode. In that mode, policy and
SAs have different match criteria.
Policy catches the whole subnet addresses, and SA catches the tunnel gateways
addresses. The source address of such tunnel is not known during egress packet
traversal in flow steering as it is added only after successful encryption.
As reqid is required for packet offload and it is unique for every SA,
we can safely rely on it only.
The output below shows the configured egress policy and SA by strongswan:
[leonro@vm ~]$ sudo ip x s
src 192.169.101.2 dst 192.169.101.1
proto esp spi 0xc88b7652 reqid 1 mode tunnel
replay-window 0 flag af-unspec esn
aead rfc4106(gcm(aes)) 0xe406a01083986e14d116488549094710e9c57bc6 128
anti-replay esn context:
seq-hi 0x0, seq 0x0, oseq-hi 0x0, oseq 0x0
replay_window 1, bitmap-length 1
00000000
crypto offload parameters: dev eth2 dir out mode packet
[leonro@064 ~]$ sudo ip x p
src 192.170.0.0/16 dst 192.170.0.0/16
dir out priority 383615 ptype main
tmpl src 192.169.101.2 dst 192.169.101.1
proto esp spi 0xc88b7652 reqid 1 mode tunnel
crypto offload parameters: dev eth2 mode packet
Fixes: b3beba1fb4 ("net/mlx5e: Allow policies with reqid 0, to support IKE policy holes")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If failed to add SF, error handling doesn't delete the SF from the
SF table. But the hw resources are deleted. So when unload driver,
hw resources will be deleted again. Firmware will report syndrome
0x68def3 which means "SF is not allocated can not deallocate".
Fix it by delete SF from SF table if failed to add SF.
Fixes: 2597ee190b ("net/mlx5: Call mlx5_sf_id_erase() once in mlx5_sf_dealloc()")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Shay Drori <shayd@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
User added steering rules at RDMA_TX were being added to the first prio,
which is the counters prio.
Fix that so that they are correctly added to the BYPASS_PRIO instead.
Fixes: 24670b1a31 ("net/mlx5: Add support for RDMA TX steering")
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In 4.19, before the switch to linkmode bitmaps, PHY_GBIT_FEATURES
included feature bits for aneg and TP/MII ports.
SUPPORTED_TP | \
SUPPORTED_MII)
SUPPORTED_10baseT_Full)
SUPPORTED_100baseT_Full)
SUPPORTED_1000baseT_Full)
PHY_100BT_FEATURES | \
PHY_DEFAULT_FEATURES)
PHY_1000BT_FEATURES)
Referenced commit expanded PHY_GBIT_FEATURES, silently removing
PHY_DEFAULT_FEATURES. The removed part can be re-added by using
the new PHY_GBIT_FEATURES definition.
Not clear to me is why nobody seems to have noticed this issue.
I stumbled across this when checking what it takes to make
phy_10_100_features_array et al private to phylib.
Fixes: d0939c26c5 ("net: ethernet: xgbe: expand PHY_GBIT_FEAUTRES")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/46521973-7738-4157-9f5e-0bb6f694acba@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xpcs_config_2500basex() sets DW_VR_MII_DIG_CTRL1_2G5_EN, but
xpcs_config_aneg_c37_sgmii() never unsets it. So, on a protocol change
from 2500base-x to sgmii, the DW_VR_MII_DIG_CTRL1_2G5_EN bit will remain
set.
Fixes: f27abde304 ("net: pcs: add 2500BASEX support for Intel mGbE controller")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20250114164721.2879380-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On a port with SGMII fixed-link at SPEED_1000, DW_VR_MII_DIG_CTRL1 gets
set to 0x2404. This is incorrect, because bit 2 (DW_VR_MII_DIG_CTRL1_2G5_EN)
is set.
It comes from the previous write to DW_VR_MII_AN_CTRL, because the "val"
variable is reused and is dirty. Actually, its value is 0x4, aka
FIELD_PREP(DW_VR_MII_PCS_MODE_MASK, DW_VR_MII_PCS_MODE_C37_SGMII).
Resolve the issue by clearing "val" to 0 when writing to a new register.
After the fix, the register value is 0x2400.
Prior to the blamed commit, when the read-modify-write was open-coded,
the code saved the content of the DW_VR_MII_DIG_CTRL1 register in the
"ret" variable.
Fixes: ce8d6081fc ("net: pcs: xpcs: add _modify() accessors")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20250114164721.2879380-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The fec_enet_update_cbd function calls page_pool_dev_alloc_pages but did
not handle the case when it returned NULL. There was a WARN_ON(!new_page)
but it would still proceed to use the NULL pointer and then crash.
This case does seem somewhat rare but when the system is under memory
pressure it can happen. One case where I can duplicate this with some
frequency is when writing over a smbd share to a SATA HDD attached to an
imx6q.
Setting /proc/sys/vm/min_free_kbytes to higher values also seems to solve
the problem for my test case. But it still seems wrong that the fec driver
ignores the memory allocation error and can crash.
This commit handles the allocation error by dropping the current packet.
Fixes: 95698ff617 ("net: fec: using page pool to manage RX buffers")
Signed-off-by: Kevin Groeneveld <kgroeneveld@lenbrook.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20250113154846.1765414-1-kgroeneveld@lenbrook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If coalesce_count is greater than 255 it will not fit in the register and
will overflow. This can be reproduced by running
# ethtool -C ethX rx-frames 256
which will result in a timeout of 0us instead. Fix this by checking for
invalid values and reporting an error.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://patch.msgid.link/20250113163001.2335235-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "sizeof(struct cmsg_bpf_event) + pkt_size + data_size" math could
potentially have an integer wrapping bug on 32bit systems. Check for
this and return an error.
Fixes: 9816dd35ec ("nfp: bpf: perf event output helpers support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/6074805b-e78d-4b8a-bf05-e929b5377c28@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Fix E825 initialization
Grzegorz Nitka says:
E825 products have incorrect initialization procedure, which may lead to
initialization failures and register values.
Fix E825 products initialization by adding correct sync delay, checking
the PHY revision only for current PHY and adding proper destination
device when reading port/quad.
In addition, E825 uses PF ID for indexing per PF registers and as
a primary PHY lane number, which is incorrect.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Add correct PHY lane assignment
ice: Fix ETH56G FC-FEC Rx offset value
ice: Fix quad registers read on E825
ice: Fix E825 initialization
====================
Link: https://patch.msgid.link/20250113182840.3564250-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
gtp_newlink() links the gtp device to a list in dev_net(dev).
However, even after the gtp device is moved to another netns,
it stays on the list but should be invisible.
Let's use for_each_netdev_rcu() for netdev traversal in
gtp_genl_dump_pdp().
Note that gtp_dev_list is no longer used under RCU, so list
helpers are converted to the non-RCU variant.
Fixes: 459aa660eb ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Reported-by: Xiao Liang <shaw.leon@gmail.com>
Closes: https://lore.kernel.org/netdev/CABAhCOQdBL6h9M2C+kd+bGivRJ9Q72JUxW+-gur0nub_=PmFPA@mail.gmail.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The temperature sensor is actually part of the integrated PHY and available
also on the standalone versions of the PHY. Therefore hwmon support will
be added to the Realtek PHY driver and can be removed here.
Fixes: 1ffcc8d413 ("r8169: add support for the temperature sensor being available from RTL8125B")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/afba85f5-987b-4449-83cc-350438af7fe7@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Driver always naively assumes, that for PTP purposes, PHY lane to
configure is corresponding to PF ID.
This is not true for some port configurations, e.g.:
- 2x50G per quad, where lanes used are 0 and 2 on each quad, but PF IDs
are 0 and 1
- 100G per quad on 2 quads, where lanes used are 0 and 4, but PF IDs are
0 and 1
Use correct PHY lane assignment by getting and parsing port options.
This is read from the NVM by the FW and provided to the driver with
the indication of active port split.
Remove ice_is_muxed_topo(), which is no longer needed.
Fixes: 4409ea1726 ("ice: Adjust PTP init for 2x50G E825C devices")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Arkadiusz Kubalewski <Arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix ETH56G FC-FEC incorrect Rx offset value by changing it from -255.96
to -469.26 ns.
Those values are derived from HW spec and reflect internal delays.
Hex value is a fixed point representation in Q23.9 format.
Fixes: 7cab44f1c3 ("ice: Introduce ETH56G PHY model for E825C products")
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Quad registers are read/written incorrectly. E825 devices always use
quad 0 address and differentiate between the PHYs by changing SBQ
destination device (phy_0 or phy_0_peer).
Add helpers for reading/writing PTP registers shared per quad and use
correct quad address and SBQ destination device based on port.
Fixes: 7cab44f1c3 ("ice: Introduce ETH56G PHY model for E825C products")
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Current implementation checks revision of all PHYs on all PFs, which is
incorrect and may result in initialization failure. Check only the
revision of the current PHY.
Fixes: 7cab44f1c3 ("ice: Introduce ETH56G PHY model for E825C products")
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When tx_max_frame_size was added to struct ravb_hw_info, no value was
set in ravb_rzv2m_hw_info so the default value of zero was used.
The maximum MTU is set by subtracting from tx_max_frame_size to allow
space for headers and frame checksums. As ndev->max_mtu is unsigned,
this subtraction wraps around leading to a ridiculously large positive
value that is obviously incorrect.
Before tx_max_frame_size was introduced, the maximum MTU was based on
rx_max_frame_size. So, we can restore the correct maximum MTU by copying
the rx_max_frame_size value into tx_max_frame_size for RZ/V2M.
Fixes: 1d63864299 ("net: ravb: Fix maximum TX frame size for GbEth devices")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://patch.msgid.link/20250109113706.1409149-1-paul.barker.ct@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Recalculate features when XDP is detached.
Before:
# ip li set dev eth0 xdp obj xdp_dummy.bpf.o sec xdp
# ip li set dev eth0 xdp off
# ethtool -k eth0 | grep gro
rx-gro-hw: off [requested on]
After:
# ip li set dev eth0 xdp obj xdp_dummy.bpf.o sec xdp
# ip li set dev eth0 xdp off
# ethtool -k eth0 | grep gro
rx-gro-hw: on
The fact that HW-GRO doesn't get re-enabled automatically is just
a minor annoyance. The real issue is that the features will randomly
come back during another reconfiguration which just happens to invoke
netdev_update_features(). The driver doesn't handle reconfiguring
two things at a time very robustly.
Starting with commit 98ba1d931f ("bnxt_en: Fix RSS logic in
__bnxt_reserve_rings()") we only reconfigure the RSS hash table
if the "effective" number of Rx rings has changed. If HW-GRO is
enabled "effective" number of rings is 2x what user sees.
So if we are in the bad state, with HW-GRO re-enablement "pending"
after XDP off, and we lower the rings by / 2 - the HW-GRO rings
doing 2x and the ethtool -L doing / 2 may cancel each other out,
and the:
if (old_rx_rings != bp->hw_resc.resv_rx_rings &&
condition in __bnxt_reserve_rings() will be false.
The RSS map won't get updated, and we'll crash with:
BUG: kernel NULL pointer dereference, address: 0000000000000168
RIP: 0010:__bnxt_hwrm_vnic_set_rss+0x13a/0x1a0
bnxt_hwrm_vnic_rss_cfg_p5+0x47/0x180
__bnxt_setup_vnic_p5+0x58/0x110
bnxt_init_nic+0xb72/0xf50
__bnxt_open_nic+0x40d/0xab0
bnxt_open_nic+0x2b/0x60
ethtool_set_channels+0x18c/0x1d0
As we try to access a freed ring.
The issue is present since XDP support was added, really, but
prior to commit 98ba1d931f ("bnxt_en: Fix RSS logic in
__bnxt_reserve_rings()") it wasn't causing major issues.
Fixes: 1054aee823 ("bnxt_en: Use NETIF_F_GRO_HW.")
Fixes: 98ba1d931f ("bnxt_en: Fix RSS logic in __bnxt_reserve_rings()")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Link: https://patch.msgid.link/20250109043057.2888953-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
CPSW ALE has 75-bit ALE entries stored across three 32-bit words.
The cpsw_ale_get_field() and cpsw_ale_set_field() functions support
ALE field entries spanning up to two words at the most.
The cpsw_ale_get_field() and cpsw_ale_set_field() functions work as
expected when ALE field spanned across word1 and word2, but fails when
ALE field spanned across word2 and word3.
For example, while reading the ALE field spanned across word2 and word3
(i.e. bits 62 to 64), the word3 data shifted to an incorrect position
due to the index becoming zero while flipping.
The same issue occurred when setting an ALE entry.
This issue has not been seen in practice but will be an issue in the future
if the driver supports accessing ALE fields spanning word2 and word3
Fix the methods to handle getting/setting fields spanning up to two words.
Fixes: b685f1a589 ("net: ethernet: ti: cpsw_ale: Fix cpsw_ale_get_field()/cpsw_ale_set_field()")
Signed-off-by: Sudheer Kumar Doredla <s-doredla@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://patch.msgid.link/20250108172433.311694-1-s-doredla@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The pci_irq_vector() function never returns zero. It returns negative
error codes or a positive non-zero IRQ number. Fix the error checking to
test for negatives.
Fixes: a36e9f5cfe ("rtase: Add support for a pci table in this module")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/f2ecc88d-af13-4651-9820-7cc665230019@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We found a timeout problem with the pldm command on our system. The
reason is that the MCTP-I3C driver has a race condition when receiving
multiple-packet messages in multi-thread, resulting in a wrong packet
order problem.
We identified this problem by adding a debug message to the
mctp_i3c_read function.
According to the MCTP spec, a multiple-packet message must be composed
in sequence, and if there is a wrong sequence, the whole message will be
discarded and wait for the next SOM.
For example, SOM → Pkt Seq #2 → Pkt Seq #1 → Pkt Seq #3 → EOM.
Therefore, we try to solve this problem by adding a mutex to the
mctp_i3c_read function. Before the modification, when a command
requesting a multiple-packet message response is sent consecutively, an
error usually occurs within 100 loops. After the mutex, it can go
through 40000 loops without any error, and it seems to run well.
Fixes: c8755b29b5 ("mctp i3c: MCTP I3C driver")
Signed-off-by: Leo Yang <Leo-Yang@quantatw.com>
Link: https://patch.msgid.link/20250107031529.3296094-1-Leo-Yang@quantatw.com
[pabeni@redhat.com: dropped already answered question from changelog]
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-01-07 (ice, igc)
For ice:
Arkadiusz corrects mask value being used to determine DPLL phase range.
Przemyslaw corrects frequency value for E823 devices.
For igc:
En-Wei Wu adds a check and, early, return for failed register read.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: return early when failing to read EECD register
ice: fix incorrect PHY settings for 100 GB/s
ice: fix max values for dpll pin phase adjust
====================
Link: https://patch.msgid.link/20250107190150.1758577-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TQP BAR space is divided into two segments. TQPs 0-1023 and TQPs
1024-1279 are in different BAR space addresses. However,
hclge_fetch_pf_reg does not distinguish the tqp space information when
reading the tqp space information. When the number of TQPs is greater
than 1024, access bar space overwriting occurs.
The problem of different segments has been considered during the
initialization of tqp.io_base. Therefore, tqp.io_base is directly used
when the queue is read in hclge_fetch_pf_reg.
The error message:
Unable to handle kernel paging request at virtual address ffff800037200000
pc : hclge_fetch_pf_reg+0x138/0x250 [hclge]
lr : hclge_get_regs+0x84/0x1d0 [hclge]
Call trace:
hclge_fetch_pf_reg+0x138/0x250 [hclge]
hclge_get_regs+0x84/0x1d0 [hclge]
hns3_get_regs+0x2c/0x50 [hns3]
ethtool_get_regs+0xf4/0x270
dev_ethtool+0x674/0x8a0
dev_ioctl+0x270/0x36c
sock_do_ioctl+0x110/0x2a0
sock_ioctl+0x2ac/0x530
__arm64_sys_ioctl+0xa8/0x100
invoke_syscall+0x4c/0x124
el0_svc_common.constprop.0+0x140/0x15c
do_el0_svc+0x30/0xd0
el0_svc+0x1c/0x2c
el0_sync_handler+0xb0/0xb4
el0_sync+0x168/0x180
Fixes: 939ccd107f ("net: hns3: move dump regs function to a separate file")
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250106143642.539698-7-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the misc irq is initialized before reset_timer setup. But
it will access the reset_timer in the irq handler. So initialize
the reset_timer earlier.
Fixes: ff200099d2 ("net: hns3: remove unnecessary work in hclgevf_main")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250106143642.539698-6-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch modifies the implementation of debugfs:
When the user process stops unexpectedly, not all data of the file system
is read. In this case, the save_buf pointer is not released. When the
user process is called next time, save_buf is used to copy the cached
data to the user space. As a result, the queried data is stale.
To solve this problem, this patch implements .open() and .release() handler
for debugfs file_operations. moving allocation buffer and execution
of the cmd to the .open() handler and freeing in to the .release() handler.
Allocate separate buffer for each reader and associate the buffer
with the file pointer.
When different user read processes no longer share the buffer,
the stale data problem is fixed.
Fixes: 5e69ea7ee2 ("net: hns3: refactor the debugfs process")
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Guangwei Zhang <zhangwangwei6@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20250106143642.539698-4-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the netdev->features is configured in hns3_nic_set_features.
As a result, __netdev_update_features considers that there is no feature
difference, and the procedures of the real features are missing.
Fixes: 2a7556bb2b ("net: hns3: implement ndo_features_check ops for hns3 driver")
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20250106143642.539698-3-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a reset type that is not supported by the driver is input, a reset
pending flag bit of the HNAE3_NONE_RESET type is generated in
reset_pending. The driver does not have a mechanism to clear this type
of error. As a result, the driver considers that the reset is not
complete. This patch provides a mechanism to clear the
HNAE3_NONE_RESET flag and the parameter of
hnae3_ae_ops.set_default_reset_request is verified.
The error message:
hns3 0000:39:01.0: cmd failed -16
hns3 0000:39:01.0: hclge device re-init failed, VF is disabled!
hns3 0000:39:01.0: failed to reset VF stack
hns3 0000:39:01.0: failed to reset VF(4)
hns3 0000:39:01.0: prepare reset(2) wait done
hns3 0000:39:01.0 eth4: already uninitialized
Use the crash tool to view struct hclgevf_dev:
struct hclgevf_dev {
...
default_reset_request = 0x20,
reset_level = HNAE3_NONE_RESET,
reset_pending = 0x100,
reset_type = HNAE3_NONE_RESET,
...
};
Fixes: 720bd5837e ("net: hns3: add set_default_reset_request in the hnae3_ae_ops")
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250106143642.539698-2-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit f85949f982 ("xdp: add xdp_set_features_flag utility routine")
added routines to inform the core about XDP flag changes.
GVE support was added around the same time and missed using them.
GVE only changes the flags on error recover or resume.
Presumably the flags may change during resume if VM migrated.
User would not get the notification and upper devices would
not get a chance to recalculate their flags.
Fixes: 75eaae158b ("gve: Add XDP DROP and TX support for GQI-QPL format")
Reviewed-By: Jeroen de Borst <jeroendb@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250106180210.1861784-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a garbage value problem in fbnic_mac_get_sensor_asic(). 'fw_cmpl'
is uninitialized which makes 'sensor' and '*val' to be stored garbage
value. Revert commit d85ebade02 ("eth: fbnic: Add hardware monitoring
support via HWMON interface") to avoid this problem.
Fixes: d85ebade02 ("eth: fbnic: Add hardware monitoring support via HWMON interface")
Signed-off-by: Su Hui <suhui@nfschina.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20250106023647.47756-1-suhui@nfschina.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When booting with a dock connected, the igc driver may get stuck for ~40
seconds if PCIe link is lost during initialization.
This happens because the driver access device after EECD register reads
return all F's, indicating failed reads. Consequently, hw->hw_addr is set
to NULL, which impacts subsequent rd32() reads. This leads to the driver
hanging in igc_get_hw_semaphore_i225(), as the invalid hw->hw_addr
prevents retrieving the expected value.
To address this, a validation check and a corresponding return value
catch is added for the EECD register read result. If all F's are
returned, indicating PCIe link loss, the driver will return -ENXIO
immediately. This avoids the 40-second hang and significantly improves
boot time when using a dock with an igc NIC.
Log before the patch:
[ 0.911913] igc 0000:70:00.0: enabling device (0000 -> 0002)
[ 0.912386] igc 0000:70:00.0: PTM enabled, 4ns granularity
[ 1.571098] igc 0000:70:00.0 (unnamed net_device) (uninitialized): PCIe link lost, device now detached
[ 43.449095] igc_get_hw_semaphore_i225: igc 0000:70:00.0 (unnamed net_device) (uninitialized): Driver can't access device - SMBI bit is set.
[ 43.449186] igc 0000:70:00.0: probe with driver igc failed with error -13
[ 46.345701] igc 0000:70:00.0: enabling device (0000 -> 0002)
[ 46.345777] igc 0000:70:00.0: PTM enabled, 4ns granularity
Log after the patch:
[ 1.031000] igc 0000:70:00.0: enabling device (0000 -> 0002)
[ 1.032097] igc 0000:70:00.0: PTM enabled, 4ns granularity
[ 1.642291] igc 0000:70:00.0 (unnamed net_device) (uninitialized): PCIe link lost, device now detached
[ 5.480490] igc 0000:70:00.0: enabling device (0000 -> 0002)
[ 5.480516] igc 0000:70:00.0: PTM enabled, 4ns granularity
Fixes: ab40561268 ("igc: Add NVM support")
Cc: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Signed-off-by: En-Wei Wu <en-wei.wu@canonical.com>
Reviewed-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ptp4l application reports too high offset when ran on E823 device
with a 100GB/s link. Those values cannot go under 100ns, like in a
working case when using 100 GB/s cable.
This is due to incorrect frequency settings on the PHY clocks for
100 GB/s speed. Changes are introduced to align with the internal
hardware documentation, and correctly initialize frequency in PHY
clocks with the frequency values that are in our HW spec.
To reproduce the issue run ptp4l as a Time Receiver on E823 device,
and observe the offset, which will never approach values seen
in the PTP working case.
Reproduction output:
ptp4l -i enp137s0f3 -m -2 -s -f /etc/ptp4l_8275.conf
ptp4l[5278.775]: master offset 12470 s2 freq +41288 path delay -3002
ptp4l[5278.837]: master offset 10525 s2 freq +39202 path delay -3002
ptp4l[5278.900]: master offset -24840 s2 freq -20130 path delay -3002
ptp4l[5278.963]: master offset 10597 s2 freq +37908 path delay -3002
ptp4l[5279.025]: master offset 8883 s2 freq +36031 path delay -3002
ptp4l[5279.088]: master offset 7267 s2 freq +34151 path delay -3002
ptp4l[5279.150]: master offset 5771 s2 freq +32316 path delay -3002
ptp4l[5279.213]: master offset 4388 s2 freq +30526 path delay -3002
ptp4l[5279.275]: master offset -30434 s2 freq -28485 path delay -3002
ptp4l[5279.338]: master offset -28041 s2 freq -27412 path delay -3002
ptp4l[5279.400]: master offset 7870 s2 freq +31118 path delay -3002
Fixes: 3a7496234d ("ice: implement basic E822 PTP support")
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Przemyslaw Korba <przemyslaw.korba@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Mask admin command returned max phase adjust value for both input and
output pins. Only 31 bits are relevant, last released data sheet wrongly
points that 32 bits are valid - see [1] 3.2.6.4.1 Get CCU Capabilities
Command for reference. Fix of the datasheet itself is in progress.
Fix the min/max assignment logic, previously the value was wrongly
considered as negative value due to most significant bit being set.
Example of previous broken behavior:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/dpll.yaml \
--do pin-get --json '{"id":1}'| grep phase-adjust
'phase-adjust': 0,
'phase-adjust-max': 16723,
'phase-adjust-min': -16723,
Correct behavior with the fix:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/dpll.yaml \
--do pin-get --json '{"id":1}'| grep phase-adjust
'phase-adjust': 0,
'phase-adjust-max': 2147466925,
'phase-adjust-min': -2147466925,
[1] https://cdrdv2.intel.com/v1/dl/getContent/613875?explicitVersion=true
Fixes: 90e1c90750 ("ice: dpll: implement phase related callbacks")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
During ARP failure, tid is not inserted but _c4iw_free_ep()
attempts to remove tid which results in error.
This patch fixes the issue by avoiding removal of uninserted tid.
Fixes: 59437d78f0 ("cxgb4/chtls: fix ULD connection failures due to wrong TID base")
Signed-off-by: Anumula Murali Mohan Reddy <anumula@chelsio.com>
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Link: https://patch.msgid.link/20250103092327.1011925-1-anumula@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DIM work will call the firmware to adjust the coalescing parameters on
the RX rings. We should cancel DIM work before we call the firmware
to free the RX rings. Otherwise, FW will reject the call from DIM
work if the RX ring has been freed. This will generate an error
message like this:
bnxt_en 0000:21:00.1 ens2f1np1: hwrm req_type 0x53 seq id 0x6fca error 0x2
and cause unnecessary concern for the user. It is also possible to
modify the coalescing parameters of the wrong ring if the ring has
been re-allocated.
To prevent this, cancel DIM work right before freeing the RX rings.
We also have to add a check in NAPI poll to not schedule DIM if the
RX rings are shutting down. Check that the VNIC is active before we
schedule DIM. The VNIC is always disabled before we free the RX rings.
Fixes: 0bc0b97fca ("bnxt_en: cleanup DIM work on device shutdown")
Reviewed-by: Hongguang Gao <hongguang.gao@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250104043849.3482067-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When hwrm_req_replace() fails, the driver is not invoking bnxt_req_drop()
which could cause a memory leak.
Fixes: bbf33d1d98 ("bnxt_en: update all firmware calls to use the new APIs")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250104043849.3482067-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add an array size limit to the for-loop to be sure we don't try
to reference a fw_version string off the end of the fw info names
array. We know that our firmware only has a limited number
of firmware slot names, but we shouldn't leave this unchecked.
Fixes: 45d76f4929 ("pds_core: set up device and adminq")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250103195147.7408-1-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The existing SW-FW interaction flow on the driver is wrong. Follow this
wrong flow, driver would never return error if there is a unknown command.
Since firmware writes back 'firmware ready' and 'unknown command' in the
mailbox message if there is an unknown command sent by driver. So reading
'firmware ready' does not timeout. Then driver would mistakenly believe
that the interaction has completed successfully.
It tends to happen with the use of custom firmware. Move the check for
'unknown command' out of the poll timeout for 'firmware ready'. And adjust
the debug log so that mailbox messages are always printed when commands
timeout.
Fixes: 1efa9bfe58 ("net: libwx: Implement interaction with firmware")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20250103081013.1995939-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2025-01-03
Keisuke Nishimura provided a fix to check for kfifo_alloc() in the ca8210
driver.
Lizhi Xu provided a fix a corrupted list, found by syzkaller, by checking local
interfaces first.
* tag 'ieee802154-for-net-2025-01-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wpan/wpan:
mac802154: check local interfaces before deleting sdata list
ieee802154: ca8210: Add missing check for kfifo_alloc() in ca8210_probe()
====================
Link: https://patch.msgid.link/20250103160046.469363-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When ICSSG interfaces are brought down and brought up again, the
pru cores are shut down and booted again, flushing out all the memories
and start again in a clean state. Hence it is expected that the
IEP_CMP_CFG register needs to be flushed during iep_init() to ensure
that the existing residual configuration doesn't cause any unusual
behavior. If the register is not cleared, existing IEP_CMP_CFG set for
CMP1 will result in SYNC0_OUT signal based on the SYNC_OUT register values.
After bringing the interface up, calling PPS enable doesn't work as
the driver believes PPS is already enabled, (iep->pps_enabled is not
cleared during interface bring down) and driver will just return true
even though there is no signal. Fix this by disabling pps and perout.
Fixes: c1e0230eea ("net: ti: icss-iep: Add IEP driver")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>