struct sock_reuseport is an optional shared structure referenced by each
socket belonging to a reuseport group. When a socket is bound to an
address/port not yet in use and the reuseport flag has been set, the
structure will be allocated and attached to the newly bound socket.
When subsequent calls to bind are made for the same address/port, the
shared structure will be updated to include the new socket and the
newly bound socket will reference the group structure.
Usually, when an incoming packet was destined for a reuseport group,
all sockets in the same group needed to be considered before a
dispatching decision was made. With this structure, an appropriate
socket can be found after looking up just one socket in the group.
This shared structure will also allow for more complicated decisions to
be made when selecting a socket (eg a BPF filter).
This work is based off a similar implementation written by
Ying Cai <ycai@google.com> for implementing policy-based reuseport
selection.
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: couple of fixes
Couple of fixes from Ido.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge port attributes are offloaded to hardware when invoked with SELF
flag set, but it really makes no sense to reflect them when port is not
bridged.
Allow a user to change these attribute only when port is bridged and
initialize them correctly when joining or leaving a bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the bridge status of physical ports in the appropriate functions, to
be consistent with LAG join/leave and vPorts joining/leaving bridge.
Also, remove the error messages in these two functions, as we already
emit errors in both the single functions they call.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for us to fail when joining or leaving a bridge, so let
the user know about that by returning NOTIFY_BAD, as already done for
LAG join/leave and 802.1D bridges.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We set PVID to 1 in mlxsw_sp_port_vlan_init(), so we can remove this
statement.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the reset_resume() is called, the flag of SELECTIVE_SUSPEND should be
cleared and reinitialize the device, whether the SELECTIVE_SUSPEND is set
or not. If reset_resume() is called, it means the power supply is cut or the
device is reset. That is, the device wouldn't be in runtime suspend state and
the reinitialization is necessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cphy_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARM allmodconfig fails because of the addition of the FMAN driver:
drivers/built-in.o: In function `dtsec_restart_autoneg':
binder.c:(.text+0x173328): undefined reference to `mdiobus_read'
binder.c:(.text+0x173348): undefined reference to `mdiobus_write'
drivers/built-in.o: In function `dtsec_config':
binder.c:(.text+0x173d24): undefined reference to `of_phy_find_device'
drivers/built-in.o: In function `init_phy':
binder.c:(.text+0x1763b0): undefined reference to `of_phy_connect'
drivers/built-in.o: In function `stop':
binder.c:(.text+0x176014): undefined reference to `phy_stop'
drivers/built-in.o: In function `start':
binder.c:(.text+0x176078): undefined reference to `phy_start'
The reason is that the driver uses PHYLIB, but that is a loadable
module here, and fman itself is built-in.
This patch makes it possible to configure fman as a module as well
so we don't change the status of PHYLIB in an allmodconfig kernel,
and it adds a 'select PHYLIB' statement to ensure that phylib is
always built-in when fman is.
The driver uses "builtin_platform_driver(fman_driver);", which means
it cannot be unloaded, but it's still possible to have it as a loadable
module that gets loaded once and never removed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5adae51a64 ("fsl/fman: Add FMan MURAM support")
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving the caller of iptunnel_xmit_stats causes a build error in
randconfig builds that disable CONFIG_INET:
In file included from ../net/xfrm/xfrm_input.c:17:0:
../include/net/ip6_tunnel.h: In function 'ip6tunnel_xmit':
../include/net/ip6_tunnel.h:93:2: error: implicit declaration of function 'iptunnel_xmit_stats' [-Werror=implicit-function-declaration]
iptunnel_xmit_stats(dev, pkt_len);
The reason is that the iptunnel_xmit_stats definition is hidden
inside #ifdef CONFIG_INET but the caller is not. We can change
one or the other to fix it, and this patch adds a second #ifdef
around ip6tunnel_xmit() to avoid seeing the invalid call.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 039f50629b ("ip_tunnel: Move stats update to iptunnel_xmit()")
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first NFC pull request for 4.5 and it brings:
- A new driver for the STMicroelectronics ST95HF NFC chipset.
The ST95HF is an NFC digital transceiver with an embedded analog
front-end and as such relies on the Linux NFC digital
implementation. This is the 3rd user of the NFC digital stack.
- ACPI support for the ST st-nci and st21nfca drivers.
- A small improvement for the nfcsim driver, as we can now tune
the Rx delay through sysfs.
- A bunch of minor cleanups and small fixes from Christophe Ricard,
for a few drivers and the NFC core code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VFUH
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC 4.5 pull request
This is the first NFC pull request for 4.5 and it brings:
- A new driver for the STMicroelectronics ST95HF NFC chipset.
The ST95HF is an NFC digital transceiver with an embedded analog
front-end and as such relies on the Linux NFC digital
implementation. This is the 3rd user of the NFC digital stack.
- ACPI support for the ST st-nci and st21nfca drivers.
- A small improvement for the nfcsim driver, as we can now tune
the Rx delay through sysfs.
- A bunch of minor cleanups and small fixes from Christophe Ricard,
for a few drivers and the NFC core code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry reports memleak with syskaller program.
Problem is that connector bumps skb usecount but might not invoke callback.
So move skb_get to where we invoke the callback.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: e1dba01ca6 ("i2c: add generic routine to parse DT for timing information")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The function can return negative values so it should be assigned
to signed type.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci.
Link: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is reported that, with CONFIG_HZ_PERIODIC=y cpu stays at the
lowest frequency even if the usage goes to 100%, neither ondemand
nor conservative governor works, however performance and
userspace work as expected. If set with CONFIG_NO_HZ_FULL=y,
everything goes well.
This problem is caused by improper calculation of the idle_time
when the load is extremely high(near 100%). Firstly, cpufreq_governor
uses get_cpu_idle_time to get the total idle time for specific cpu, then:
1.If the system is configured with CONFIG_NO_HZ_FULL, the idle time is
returned by ktime_get, which is always increasing, it's OK.
2.However, if the system is configured with CONFIG_HZ_PERIODIC,
get_cpu_idle_time might not guarantee to be always increasing,
because it will leverage get_cpu_idle_time_jiffy to calculate the
idle_time, consider the following scenario:
At T1:
idle_tick_1 = total_tick_1 - user_tick_1
sample period(80ms)...
At T2: ( T2 = T1 + 80ms):
idle_tick_2 = total_tick_2 - user_tick_2
Currently the algorithm is using (idle_tick_2 - idle_tick_1) to
get the delta idle_time during the past sample period, however
it CAN NOT guarantee that idle_tick_2 >= idle_tick_1, especially
when cpu load is high.
(Yes, total_tick_2 >= total_tick_1, and user_tick_2 >= user_tick_1,
but how about idle_tick_2 and idle_tick_1? No guarantee.)
So governor might get a negative value of idle_time during the past
sample period, which might mislead the system that the idle time is
very big(converted to unsigned int), and the busy time is nearly zero,
which causes the governor to always choose the lowest cpufreq,
then cause this problem.
In theory there are two solutions:
1.The logic should not rely on the idle tick during every sample period,
but be based on the busy tick directly, as this is how 'top' is
implemented.
2.Or the logic must make sure that the idle_time is strictly increasing
during each sample period, then there would be no negative idle_time
anymore. This solution requires minimum modification to current code
and this patch uses method 2.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=69821
Reported-by: Jan Fikar <j.fikar@gmail.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The max outstanding commands is being printed with a 0x prefix to
suggest it is a hex value, when in fact the integer decimal %d format
specifier is being used and this is a bit confusing. Use %x instead to
match the proceeding 0x prefix.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This set of changes adds support for the Tegra210 SoC and contains a
couple fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/f1y
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.5-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk: tegra: Changes for v4.5-rc1
This set of changes adds support for the Tegra210 SoC and contains a
couple fixes and cleanups.
There is no need to worry about module and __init text disappearing
case, because that ftrace has a module notifier that is called when
a module is being unloaded and before the text goes away and this
code grabs the ftrace_lock mutex and removes the module functions
from the ftrace list, such that it will no longer do any
modifications to that module's text, the update to make functions
be traced or not is done under the ftrace_lock mutex as well.
And by now, __init section codes should not been modified
by ftrace, because it is black listed in recordmcount.c and
ignored by ftrace.
Link: http://lkml.kernel.org/r/1449367378-29430-6-git-send-email-huawei.libin@huawei.com
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Li Bin <huawei.libin@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When lighting up the segment identifying wireless controller, Instead of
sending command directly to the controller, let's do it via LED API (usinf
led_set_brightness) so that LED object state is in sync with controller
state and we'll light up the correct segment on resume as well.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The irq_out urb is dead after suspend/ resume on my x360 wr pad. (also
reproduced by Zachary Lund [0]) Work around this by implementing
suspend, resume, and reset_resume callbacks and properly shutting down
URBs on suspend and restarting them on resume.
[0]: https://github.com/paroj/xpad/issues/6
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Backport of this upstream commit into stable kernels :
89c22d8c3b ("net: Fix skb csum races when peeking")
exposed a bug in udp stack vs MSG_PEEK support, when user provides
a buffer smaller than skb payload.
In this case,
skb_copy_and_csum_datagram_iovec(skb, sizeof(struct udphdr),
msg->msg_iov);
returns -EFAULT.
This bug does not happen in upstream kernels since Al Viro did a great
job to replace this into :
skb_copy_and_csum_datagram_msg(skb, sizeof(struct udphdr), msg);
This variant is safe vs short buffers.
For the time being, instead reverting Herbert Xu patch and add back
skb->ip_summed invalid changes, simply store the result of
udp_lib_checksum_complete() so that we avoid computing the checksum a
second time, and avoid the problematic
skb_copy_and_csum_datagram_iovec() call.
This patch can be applied on recent kernels as it avoids a double
checksumming, then backported to stable kernels as a bug fix.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be consistent with other DCE11 functions test for crtc < 0.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Mimics odd behaviour where (i++ % 100 == 0) is true in the first iteration of each loop...
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Simplified the ring test and added logic to ensure rings are marked not ready
by default.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
More LOC reductions in VCE3 code. This patch simplifies the is_idle and
wait_for_idle logic.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Since t4_alloc_mem can be failed in memory pressure,
if not properly handled, NULL dereference could be happened.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since qlcnic_alloc_mbx_args can be failed,
return value should be checked.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chunhao Lin says:
====================
Fix some typos in setting hardware parameter
The typos are in setting RTL8168DP, RTL8168EP and RTL8168H hardware parameters.
This series of patch fix these typos.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The original way is wrong, it always writes ephy reg 0x03.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY PFM register is in PHY page 0x0a44 register 0x11, not 0x14.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register for setting D3code PFM mode is MISC_1, not DLLPR.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Reviewed-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 79c441ae50 ("ppp: implement x-netns support"), the PPP layer
calls skb_scrub_packet() whenever the skb is received on the PPP
device. Manually resetting packet meta-data in the L2TP layer is thus
redundant.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some sysfs attributes in /sys/power/ should really be read-only,
so add support for that, convert those attributes to read-only
and drop the stub .show() routines from them.
Original-by: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a missing space in the definition of struct acpi_device_bus_id.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
[ rjw: Subject and changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cast to uint8_t happens before the right shift so this always sets
.m3arb to zero. The cast is actually a no-op so we can remove it.
Fixes: 3bace35914 ('drm/amd/powerplay: add hardware manager sub-component')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This code is indented too far. Also we normally use spaces to align if
statement conditions.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This test was reversed so it would end up leading to a NULL dereference.
Fixes: 4630f0faae ('drm/amd/powerplay: add Carrizo smu support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The indenting in acpi_battery_set_alarm is inconsistent and has been
so since 2007; commit 94f6c08601
("ACPI: SBS: Add support for power_supply class (and sysfs)"). Minor
fix for this, no code functionality change.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
I have a device (Nuvoton 6779D Super-IO IR RC with nuvoton-cir driver)
which works after initial boot but not any longer if I unload and
re-load the driver module.
Digging into the issue I found that unloading the driver calls
pnp_disable_dev although the driver has flag PNP_DRIVER_RES_DO_NOT_CHANGE
set. IMHO this is not right.
Let's have a look at the call chain when probing a device:
pnp_device_probe
1. attaches the device
2. if it's not active and PNP_DRIVER_RES_DO_NOT_CHANGE is not set
it gets activated
3. probes driver
I think pnp_device_remove should do it in reverse order and also
respect PNP_DRIVER_RES_DO_NOT_CHANGE. Therefore:
1. call drivers remove callback
2. if device is active and PNP_DRIVER_RES_DO_NOT_CHANGE is not set
disable it
3. detach device
The change works for me and sounds logical to me.
However I don't know the pnp driver in detail so I might be wrong.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sergei Shtylyov says:
====================
sh_eth: remove unused BE descriptor support
Here's a set of 2 patches against DaveM's 'net-next.git' repo plus the
recently merged to 'net.git' repo fix for the 16-bit descriptor endianness.
We get rid of ~30 LoCs and ~300 bytes of code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that {cpu|edmac}_to_{edmac|cpu}() functions boiled down to the mere
{cpu|le32}_to_{le32|cpu}() calls, there's no need for these functions
anymore, so just get rid of them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 71557a37ad ("[netdrvr] sh_eth: Add SH7619 support") added support
for the big-endian EDMAC descriptors. However, it was never used and never
worked right until the recent driver fixes. I think we now can just remove
this support, it was only burdening the driver from the start. It should be
easy to do without disturbing the SH platform code, at least for now...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of re-creating the array on the stack each time
is_cmos_rtc_device() gets called, make the array 'static const'.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
