Add to the user triggered fw debug collection support for describing
the reason of the trigger.
This could be useful for identifying a dump by a unique id, passed as
a description.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Firmware will support filtering multicast L3 packets.
The L3 filtering is configured by the WOWLAN_CONFIG command.
All flags should be enabled by default.
Older firmware is not affected as it does not look into
this field.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of keeping the fw_key_table bits set when the keys are removed
(i.e. in D3 entry or HW_RESTART flows), clear them and set them again
only when the keys have been successfully re-added. This makes the
bitmask more closely tied to the actual firmware programming.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the op_mode sends an skb whose payload is bigger than
MSS, PCIe will create an A-MSDU out of it. PCIe assumes
that the skb that is coming from the op_mode can fit in one
A-MSDU. It is the op_mode's responsibility to make sure
that this guarantee holds.
Additional headers need to be built for the subframes.
The TSO core code takes care of the IP / TCP headers and
the driver takes care of the 802.11 subframe headers.
These headers are stored on a per-cpu page that is re-used
for all the packets handled on that same CPU. Each skb
holds a reference to that page and releases the page when
it is reclaimed. When the page gets full, it is released
and a new one is allocated.
Since any SKB that doesn't go through the fast-xmit path
of mac80211 will be segmented, we can assume here that the
packet is not WEP / TKIP and has a proper SNAP header.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable TPS65217 regulator to have rootfs in MMC for Beagle Bone's.
Suggested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The UniPhier SoCs support pinctrl drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
A fix for a nasty hardware bug in rk808 and a initialization reordering in
da9063 to fix a possible crash.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xXh7
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fixes from Alexandre Belloni:
"Late fixes for the RTC subsystem for 4.4:
A fix for a nasty hardware bug in rk808 and an initialization
reordering in da9063 to fix a possible crash"
* tag 'rtc-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: da9063: fix access ordering error during RTC interrupt at system power on
rtc: rk808: Compensate for Rockchip calendar deviation on November 31st
This is an API consolidation only. The use of kmalloc + memset to 0
is equivalent to kcalloc in this case as it is allocating an array
of elements.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The s3fwrn5_phy_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TPM2 supports authorization policies, which are essentially
combinational logic statements repsenting the conditions where the data
can be unsealed based on the TPM state. This patch enables to use
authorization policies to seal trusted keys.
Two following new options have been added for trusted keys:
* 'policydigest=': provide an auth policy digest for sealing.
* 'policyhandle=': provide a policy session handle for unsealing.
If 'hash=' option is supplied after 'policydigest=' option, this
will result an error because the state of the option would become
mixed.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
Added 'hash=' option for selecting the hash algorithm for add_key()
syscall and documentation for it.
Added entry for sm3-256 to the following tables in order to support
TPM_ALG_SM3_256:
* hash_algo_name
* hash_digest_size
Includes support for the following hash algorithms:
* sha1
* sha256
* sha384
* sha512
* sm3-256
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
The trusted keys option parsing allows specifying the same option
multiple times. The last option value specified is used.
This is problematic because:
* No gain.
* This makes complicated to specify options that are dependent on other
options.
This patch changes the behavior in a way that option can be specified
only once.
Reported-by: James Morris James Morris <jmorris@namei.org>
Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
When the TPM response reception is interrupted in the wait_event_interruptable
call, the TPM is still busy processing the command and will only deliver the
response later. So we have to wait for an outstanding response before sending
a new request to avoid trying to put a 2nd request into the CRQ. Also reset
the res_len before sending a command so we will end up in that
wait_event_interruptable() waiting for the response rather than reading the
command packet as a response.
The easiest way to trigger the problem is to run the following
cd /sys/device/vio/71000004
while :; cat pcrs >/dev/null; done
And press Ctrl-C. This will then display an error
tpm_ibmvtpm 71000004: tpm_transmit: tpm_recv: error -4
followed by several other errors once interaction with the TPM resumes.
tpm_ibmvtpm 71000004: A TPM error (101) occurred attempting to determine the number of PCRS.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Ashley Lai <ashley@ashleylai.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
auto-probing doesn't work with shared interrupts, and the auto detection
interrupt range is for x86 only.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
Now that the probe and run cases are merged together we can use a
much simpler setup flow where probe and normal setup are done with
exactly the same code.
Since the new flow always calls tpm_gen_interrupt to confirm the IRQ
there is also no longer any need to call tpm_get_timeouts twice.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
The new code that works directly in tpm_tis_send is able to handle
IRQ probing duties as well, so just use it for everything.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off--by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
IRQ probing needs to know that the TPM is working before trying to
probe, so move tpm_get_timeouts() to the top of the tpm_tis_init().
This has the advantage of also getting the correct timeouts loaded
before doing IRQ probing.
All the timeout handling code is moved to tpm_get_timeouts() in order to
remove duplicate code in tpm_tis and tpm_crb.
[jarkko.sakkinen@linux.intel.com: squashed two patches together and
improved the commit message.]
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
This should be done very early, before anything could possibly
cause the TPM to generate an interrupt. If the IRQ line is shared
with another driver causing an interrupt before setting up our
handler will be very bad.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
The interrupt is always allocated with devm_request_irq so it
must always be freed with devm_free_irq.
Fixes: 448e9c55c1 ("tpm_tis: verify interrupt during init")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
Add BCM2E65 device in acpi_device_id table used on Asus T100TAF.
Signed-off-by: Luka Karinja <luka.karinja@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The transport will need to use the info->driver_data
pointers. Since the op_mode has this memory hot in cache,
clear it there.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The code that handles the TBs that contain the WiFi payload
will be changed for TSO. Move the current code into a
separate function.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Differentiate between the cases where the skb is a large
send and the other cases.
Advertise TSO even if, at this stage, skb_gso_segment will
be called and it will do all the work.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow to configure the driver to pretend to have TX CSUM
offload support. This will be useful to test the TSO flows
that will come in further patches.
This configuration is disabled by default.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This fix alters the ordering of the IRQ and device registrations in the RTC
driver probe function. This change will apply to the RTC driver that supports
both DA9063 and DA9062 PMICs.
A problem could occur with the existing RTC driver if:
A system is started from a cold boot using the PMIC RTC IRQ to initiate a
power on operation. For instance, if an RTC alarm is used to start a
platform from power off.
The existing driver IRQ is requested before the device has been properly
registered.
i.e.
ret = devm_request_threaded_irq()
comes before
rtc->rtc_dev = devm_rtc_device_register();
In this case, the interrupt can be called before the device has been
registered and the handler can be called immediately. The IRQ handler
da9063_alarm_event() contains the function call
rtc_update_irq(rtc->rtc_dev, 1, RTC_IRQF | RTC_AF);
which in turn tries to access the unavailable rtc->rtc_dev.
The fix is to reorder the functions inside the RTC probe. The IRQ is
requested after the RTC device resource has been registered so that
get_irq_byname is the last thing to happen.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
In A.D. 1582 Pope Gregory XIII found that the existing Julian calendar
insufficiently represented reality, and changed the rules about
calculating leap years to account for this. Similarly, in A.D. 2013
Rockchip hardware engineers found that the new Gregorian calendar still
contained flaws, and that the month of November should be counted up to
31 days instead. Unfortunately it takes a long time for calendar changes
to gain widespread adoption, and just like more than 300 years went by
before the last Protestant nation implemented Greg's proposal, we will
have to wait a while until all religions and operating system kernels
acknowledge the inherent advantages of the Rockchip system. Until then
we need to translate dates read from (and written to) Rockchip hardware
back to the Gregorian format.
This patch works by defining Jan 1st, 2016 as the arbitrary anchor date
on which Rockchip and Gregorian calendars are in sync. From that we can
translate arbitrary later dates back and forth by counting the number
of November/December transitons since the anchor date to determine the
offset between the calendars. We choose this method (rather than trying
to regularly "correct" the date stored in hardware) since it's the only
way to ensure perfect time-keeping even if the system may be shut down
for an unknown number of years. The drawback is that other software
reading the same hardware (e.g. mainboard firmware) must use the same
translation convention (including the same anchor date) to be able to
read and write correct timestamps from/to the RTC.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
After commit 739ae3452d ("phy: berlin-usb: Set drvdata for phy and
use it"), we get the address of priv by phy_get_drvdata(), so there's
no need to set device's driver_data any more. This patch removes the
call of platform_set_drvdata().
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We don't need gpio related header files, so remove them.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The BCM7xxx ARM-based and MIPS-based platforms share a similar hardware
block for AHCI SATA3.
This new compatible string, "brcm,bcm7425-sata-phy", may be used for
most MIPS-based platforms of 40nm process technology.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add data for phy version, and the default value of version is using the
BRCM_SATA_PHY_28NM.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
While reviewing Michael Kerrisk's recent futex manpage update, I noticed
that we allow the FUTEX_CLOCK_REALTIME flag for FUTEX_WAIT_BITSET but
not for FUTEX_WAIT.
FUTEX_WAIT is treated as a simple version for FUTEX_WAIT_BITSET
internally (with a bitmask of FUTEX_BITSET_MATCH_ANY). As such, I cannot
come up with a reason for this exclusion for FUTEX_WAIT.
This change does modify the behavior of the futex syscall, changing a
call with FUTEX_WAIT | FUTEX_CLOCK_REALTIME from returning -ENOSYS, to be
equivalent to FUTEX_WAIT_BITSET | FUTEX_CLOCK_REALTIME with a bitset of
FUTEX_BITSET_MATCH_ANY.
Reported-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Link: http://lkml.kernel.org/r/9f3bdc116d79d23f5ee72ceb9a2a857f5ff8fa29.1450474525.git.dvhart@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
out_unlock: does not only drop the locks, it also drops the refcount
on the pi_state. Really intuitive.
Move the label after the put_pi_state() call and use 'break' in the
error handling path of the requeue loop.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <darren@dvhart.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Bhuvanesh_Surachari@mentor.com
Cc: Andy Lowe <Andy_Lowe@mentor.com>
Link: http://lkml.kernel.org/r/20151219200607.526665141@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In the error handling cases we neither have pi_state nor a reference
to it. Remove the pointless code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <darren@dvhart.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Bhuvanesh_Surachari@mentor.com
Cc: Andy Lowe <Andy_Lowe@mentor.com>
Link: http://lkml.kernel.org/r/20151219200607.432780944@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Documentation of the pi_state refcounting in the requeue code is non
existent. Add it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <darren@dvhart.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Bhuvanesh_Surachari@mentor.com
Cc: Andy Lowe <Andy_Lowe@mentor.com>
Link: http://lkml.kernel.org/r/20151219200607.335938312@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
free_pi_state() is confusing as it is in fact only freeing/caching the
pi state when the last reference is gone. Rename it to put_pi_state()
which reflects better what it is doing.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <darren@dvhart.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Bhuvanesh_Surachari@mentor.com
Cc: Andy Lowe <Andy_Lowe@mentor.com>
Link: http://lkml.kernel.org/r/20151219200607.259636467@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If the proxy lock in the requeue loop acquires the rtmutex for a
waiter then it acquired also refcount on the pi_state related to the
futex, but the waiter side does not drop the reference count.
Add the missing free_pi_state() call.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <darren@dvhart.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Bhuvanesh_Surachari@mentor.com
Cc: Andy Lowe <Andy_Lowe@mentor.com>
Link: http://lkml.kernel.org/r/20151219200607.178132067@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
The USB phys on Rockchip SoCs contain their own internal PLLs to create
the 480MHz needed. Additionally this PLL output is also fed back into the
core clock-controller as possible source for clocks like the GPU or others.
Until now this was modelled incorrectly with a "virtual" factor clock in
the clock controller. The one big caveat is that if we turn off the usb phy
via the siddq signal, all analog components get turned off, including the
PLLs. It is therefore possible that a source clock gets disabled without
the clock driver ever knowing, possibly making the system hang.
Therefore register the phy-plls as real clocks that the clock driver can
then reference again normally, making the clock hirarchy finally reflect
the actual hardware.
The phy-ops get converted to simply turning that new clock on and off
which in turn controls the siddq signal of the phy.
Through this the driver gains handling for platform-specific data, to
handle the phy->clock name association.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We need custom handling for these two socs in the driver shortly,
so add the necessary compatible values to binding and driver.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This unclutters the loop in probe a lot and makes current (and future)
error handling easier to read.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This introduces a common struct that holds data belonging to
the umbrella device that contains all the phys and that we
want to use later.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently the phy driver only gets the optional clock reference but
never puts it again, neither during error handling nor on remove.
Fix that by moving the clk_put to a devm-action that gets called at
the right time when all other devm actions are done.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Support hi6220 use phy for HiKey board
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Note this commit only adds support for phys 1-3, phy 0, the otg phy, is
not yet (fully) supported after this commit.
Signed-off-by: Reinder de Haan <patchesrdh@mveas.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
