The nand in atlas7 has two chip select line. But in most time, the
nand only has one chip, so only one chip select line is enough.
The nand driver select this new pin group can free one chip select
line for other modules to avoid pin conflict.
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As the pxa architecture, at least for pxa27x, supports pin control,
activate it in the pinctrl tree.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pxa27x architecture, which is a pxa2xx with 128 pins. The
registers spacing, and pins logic is common to pxa2xx, only the pins and
their alternate function are specific to pxa27x.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pin configuration for pxa2xx architectures. PXA doesn't provide any
bias, push, pull capabilities. The only capability is to set a state for
the pins when the platform enter sleep or deep sleep mode.
The state of a pin is set by :
- whether the GPIO direction was input or output
- if it is output, a register set programs whether the pin should be
held to ground or VccIO
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver is inspired from the sunxi driver. The pxa architecture
specificities leading to the driver are :
- each pin has 8 possible alternate functions
- 4 of these are output kind
- 4 of these are input kind
- there is always a "gpio input" and "gpio output" function
- the function matrix is very scattered :
- some functions can be found on 5 different pads
- the number of functions is greater than the number of pins
- there is no "topology" grouping of pins (such as all SPI in one
corner of the die)
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a pincontrol driver for pxa2xx architecture, encompassing all pxa25x
and pxa27x variants. This is only the pin muxing part of the driver.
One specific consideration is also the memory space (MMIO), which is
intertwined with the GPIO registers. To make things worse, the GPIO
direction register also affect pin muxing, as it chooses the "kind" of
pin, ie. the 4 output functions or 4 input functions.
The mapping between pinctrl notions and PXA Technical Reference Manual
is as follows :
- a pin is obviously a pin
- a group is also a pin, ie. group P101 is the pin 101
- a mux function is an alternate function
(ie. gpio-in, gpio-out, MMCLK, BTRTS, etc ...)
The individual architecture (pxa27x, pxa25x) instantiate a pin control
by providing a table of pins, each pin being provided a list of
PXA_FUNCTION (alternate functions).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pinctrl pxa drivers to the pxa maintained files.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt management is changed by this patch to rely on chip data
instead of chained interrupts.
The main goal is to loosen the dependency on the global pxa chip
structure in favor of the passed chip data. The secondary goal is to
better show in /proc/interrupts the difference between interrupts for
gpio0 and gpio1 (directly wired to interrupt controller), and the other
gpios (wired onto a third line in the interrupt controller).
The last advantage of this patch is that the interrupt is actually
requested, so that another driver cannot steal this line, or overwrite
the handler.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the device managed ioremap to simplify the probe function.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pxa gpio IP is provided by one chip, which holds multiple banks.
Another reason the driver should register only one gpiochip instead of
multiple gpiochips (ie. 1 per each bank) is that for pincontrol and
devicetree integration (think gpio-ranges), it's impossible to have the
contiguous pin range 0..127 mapped to gpios 0..127.
This patch, amongst other thinks, paves the path to loosen the bond with
the global structure variable pxa_gpio_chip.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on a x86-only patch by Andy Lutomirski <luto@amacapital.net>
With modular kernels, 'make install' is going to need the installed
modules at some point to generate the initramfs.
Signed-off-by: Michal Marek <mmarek@suse.cz>
The sahara_dump_descriptors and sahara_dump_links functions attempt
to print a dma_addr_t value with a 0x%08x format string, which
produces a warning when dma_addr_t is 64-bit wide:
drivers/crypto/sahara.c:419:120: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
This changes the code to use the %pad format string that is meant
for dma_addr_t, which avoids the warning and gives us the correct
output in all configurations.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The sahara hardware uses DMA descriptors with 32-bit addresses, but
dma_addr_t is variable size depending on whether we want to support
any devices that use 64-bit DMA addresses in hardware.
This means that the definition of the DMA descriptor structure is wrong,
and we helpfully get a compiler warning about them too:
drivers/crypto/sahara.c:423:372: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
This changes the definition of the sahara_hw_desc and sahara_hw_link
structures to only contain fixed-length members, which is required
to make the driver work on ARM LPAE mode, and avoids most of the
gcc warnings we get.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The drbg_state_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A couple of i915_audio_component ops have been added and accessed
directly from patch_hdmi.c. Ideally all these should be factored out
into hdac_i915.c.
This patch does it, adds two new helper functions for setting N/CTS
and fetching ELD bytes. One bonus is that the hackish widget vs port
mapping is also moved to hdac_i915.c, so that it can be fixed /
enhanced more cleanly.
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since we have a new audio component ops to fetch the current ELD and
state now, we can reduce the usage of unsol event of HDMI/DP pins.
The unsol event isn't only unreliable, but it also needs the power
up/down of the codec and link at each time, which is a significant
power and time loss.
In this patch, the jack creation and unsol/jack event handling are
modified to use the audio component for the dedicated Intel chips.
The jack handling got slightly more codes than a simple usage of
hda_jack layer since we need to deal directly with snd_jack object;
the hda_jack layer is basically designed for the pin sense read and
unsol events, both of which aren't used any longer in our case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here are the patchset to add get_eld op to audio component for
communicating more directly between i915 and HD-audio.
Currently, the HDMI/DP audio status and ELD are notified and obtained
via the hardware-level communication over HD-audio unsolicited event
and verbs although the graphics driver holds the exactly same
information. As we already have a notification via audio component,
this is another step forward; namely, the audio driver may fetch
directly the audio status and ELD via the new component op.
The commits are based on Dave's latest drm-next branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=NShN
-----END PGP SIGNATURE-----
Merge tag 'drm-i915-get-eld' into topic/hdmi-jack
Merge the latest i915 audio component changes for HDMI/DP get_eld ops.
This is actually used in HD-audio side in this branch.
The recent commit [e90247f9fc: ALSA: hda - Split ELD update code
from hdmi_present_sense()] rewrote the HDMI jack handling code, but a
slight behavior change sneaked in unexpectedly. When the jack isn't
connected, it tries repoll unnecessarily.
This patch addresses the flaw, to the right behavior as before.
Fixes: e90247f9fc ('ALSA: hda - Split ELD update code from hdmi_present_sense()')
Reported-and-tested-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Based on Chris Wilson's patch from 6 months ago, rebased and adapted.
The current implementation of intel_ring_initialized() is too heavyweight;
it's a non-inlined function that chases several levels of pointers. This
wouldn't matter too much if it were rarely called, but it's used inside
the iterator test of for_each_ring() and is therefore called quite
frequently. So let's make it simple and inline ...
The idea here is to use ring->dev as an indicator showing which engines
have been initialised and are therefore to be included in iterations that
use for_each_ring(). This allows us to avoid multiple memory references
and a (non-inlined) function call on each iteration of each such loop.
Fixes regression from
commit 48d823878d
Author: Oscar Mateo <oscar.mateo@intel.com>
Date: Thu Jul 24 17:04:23 2014 +0100
drm/i915/bdw: Generic logical ring init and cleanup
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449586956-32360-2-git-send-email-david.s.gordon@intel.com
Pass the net pointer to the call_batch callback functions so we can skip
recurrent lookups.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Tested-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
This patch adds a reverse mapping from a digital port number to
intel_encoder object containing the corresponding intel_digital_port.
It simplifies the query of the encoder a lot.
Note that, even if it's a valid digital port, the dig_port_map[] might
point still to NULL -- usually it implies a DP MST port. Due to this
fact, the NULL check in each place has no WARN_ON() and just skips the
port. Once when the situation changes in future, we might introduce
WARN_ON() for a more strict check.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implement a new i915_audio_component_ops, get_eld(). It's called by
the audio driver to fetch the current audio status and ELD of the
given HDMI/DP port. It returns the size of expected ELD bytes if it's
valid, zero if no valid ELD is found, or a negative error code. The
current state of audio on/off is stored in the given pointer, too.
Note that the returned size isn't limited to the given max bytes. If
the size is greater than the max bytes, it means that only a part of
ELD has been copied back.
For achieving this implementation, a new field audio_connector is
added to struct intel_digital_port. It points to the connector
assigned to the given digital port. It's set/reset at each audio
enable/disable call in intel_audio.c, and protected with av_mutex.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On entry from el0, we save all the registers on the kernel stack, and
restore them before returning. x29 remains unchanged when we call out
to C code, which will store x29 as the frame-pointer on the stack.
Instead, write 0 into x29 after entry from el0, to avoid any risk of
tracing into user space.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When unwind_frame() reaches the bottom of the irq_stack, the last fp
points to the original task stack. unwind_frame() uses
IRQ_STACK_TO_TASK_STACK() to find the sp value. If either values is
wrong, we may end up walking a corrupt stack.
Check these values are sane by testing if they are both on the stack
pointed to by current->stack.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
irq_stack is a per_cpu variable, that needs to be access from entry.S.
Use an assembler macro instead of the unreadable details.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Due to the recent change, HDA controller driver for Intel PCH tries to
bind i915 audio component always at the probe time no matter whether
HDMI/DP codec is found. This is, however, superflulous for old
chipsets (e.g. on IVB) where they don't have always the HDMI/DP codecs
but often have only a discrete GPU instead.
For the newer chipsets, we need already the i915 binding from the
beginning due to power well control. Meanwhile, for older chipsets
where we don't need power well, we don't need the i915 binding at the
controller level.
This patch removes again the i915 binding in the HDA controller driver
for old Intel PCHs, but adds the binding in HDMI/DP codec driver
instead. This allows still the use of the direct notification from
the graphics driver while we can avoid the unnecessary load of i915
driver for machines only with another GPU.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The audio component is enabled only when CONFIG_SND_HDA_I915 is set.
Give a dummy macro for allowing the compiler optimize out the relevant
codes when this Kconfig isn't set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a static inline function ipv6_addr_prefix_copy which
copies a ipv6 address prefix(argument pfx) into the ipv6 address prefix.
The prefix len is given by plen as bits. This function mainly based on
ipv6_addr_prefix which copies one address prefix from address into a new
ipv6 address destination and zero all other address bits.
The difference is that ipv6_addr_prefix_copy don't get a prefix from an
ipv6 address, it sets a prefix to an ipv6 address with keeping other
address bits. The use case is for context based address compression
inside 6LoWPAN IPHC header which keeping ipv6 prefixes inside a context
table to lookup address-bits without sending them.
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: Łukasz Duda <lukasz.duda@nordicsemi.no>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When an inconsistent space cache is detected during loading we log a
warning that users frequently mistake as instruction to invalidate the
cache manually, even though this is not required. Fix the message to
indicate that the cache will be rebuilt automatically.
Signed-off-by: Holger Hoffstätte <holger.hoffstaette@googlemail.com>
Acked-by: Filipe Manana <fdmanana@suse.com>
When disable_noatomic is called plane_mask is not correct yet, and
plane_state->visible = true is left as true after disabling the primary
plane.
Other planes are already disabled as part of crtc sanitization, only the
primary is left active. But the plane_mask is not updated here. It gets
updated during fb takeover in modeset_gem_init, or set to the new value
on resume.
This means that to disable the primary plane 1 << drm_plane_index(primary)
needs to be used.
Afterwards because the crtc is no longer active it's forbidden to keep
plane_state->visible set, or a WARN_ON in
intel_plane_atomic_calc_changes triggers. There are other code points
that rely on accurate plane_state->visible too, so make sure the bool is
cleared.
The other planes are already disabled in intel_sanitize_crtc, so they
don't have to be handled here.
Cc: stable@vger.kernel.org #v4.3, v4.2?
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92655
Tested-by: Tomas Mezzadra <tmezzadra@gmail.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/5652DB88.9070208@linux.intel.com
(cherry picked from commit 54a4196188)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for
the libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Instead of using linux/types.h, drm headers should use drm.h, in order
to handle the portability issues in only one place.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Instead of using linux/types.h, drm headers should use drm.h, in order
to handle the portability issues in only one place.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Kernel headers exported to userspace are supposed to use these.
Fixes compilation errors in userspace:
error: unknown type name ‘uint64_t’
error: unknown type name ‘uint32_t’
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
