Gen2 reports FIFO underruns whenever no planes are enabled on the pipe.
So in order to avoid false positives we must enable the FIFO underrun
reporting only when at least one plane is enabled on the pipe. For
now just move the underrun reporting enable/disable points to the
other side of the plane enable/disable point. That doesn't cover cases
when we turn off all the planes for the pipe but leave the pipe running
on purpose, but it's better than the current situation.
On gen4+ we can actually move the underrun reporting enable/disable to
the opposite ends of the crtc enable/disable hooks. I suppose in theory
we could leave the underrun reporting enabled all the time, except on
VLV where PIPESTAT stops working when the display power well is down.
If we ever get around to unifying the PIPESTAT irq handling for all
gmch platforms, we should still follow the VLV route for other platforms.
It would also micro-optimize the irq handler a bit since we could then
skip the PIPESTAT reads for all disabled pipes.
Gen3 is still a mystery, but for now I'm going to assume it behaves
like gen4+.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Checking whether the error interrupt was enabled or not isn't really
necessary when we check for uncleared FIFO underruns. If it was enabled
we'll race with the interrupt handler a bit, but that seems OK as we
still claim the interrupt.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FIFO underruns don't generate interrupts on gmch platforms, so
if we want to know whether a modeset triggered FIFO underruns we
need to explicitly check for them.
As a modeset on one pipe could cause underruns on other pipes,
check for underruns on all pipes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
[danvet: Fix up merge error, kudos to Ville for noticing it.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Test vectors were taken from existing test for
CBC(DES3_EDE). Associated data has been added to test vectors.
HMAC computed with Crypto++ has been used. Following algos have
been covered.
(a) "authenc(hmac(sha1),cbc(des))"
(b) "authenc(hmac(sha1),cbc(des3_ede))"
(c) "authenc(hmac(sha224),cbc(des))"
(d) "authenc(hmac(sha224),cbc(des3_ede))"
(e) "authenc(hmac(sha256),cbc(des))"
(f) "authenc(hmac(sha256),cbc(des3_ede))"
(g) "authenc(hmac(sha384),cbc(des))"
(h) "authenc(hmac(sha384),cbc(des3_ede))"
(i) "authenc(hmac(sha512),cbc(des))"
(j) "authenc(hmac(sha512),cbc(des3_ede))"
Signed-off-by: Vakul Garg <vakul@freescale.com>
[NiteshNarayanLal@freescale.com: added hooks for the missing algorithms test and tested the patch]
Signed-off-by: Nitesh Lal <NiteshNarayanLal@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
With DMA-API debug enabled testmgr triggers a "DMA-API: device driver maps memory from stack" warning, when tested on a crypto HW accelerator.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The checking for the type of algorithm implementation is pretty
strange here. Use regular flags to check for the type instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use a standard accessor instead of directly digging into a structure.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: Michal Ludvig <michal@logix.cz>
Cc: Varun Wadekar <vwadekar@nvidia.com>
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: linux-geode@lists.infradead.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Consistently use AES_KEYSIZE_128 instead of arbitrary defined value.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: Michal Ludvig <michal@logix.cz>
Cc: Varun Wadekar <vwadekar@nvidia.com>
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: linux-geode@lists.infradead.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The AES IV length is always 128bits, just use the define from aes.h
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: Michal Ludvig <michal@logix.cz>
Cc: Varun Wadekar <vwadekar@nvidia.com>
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: linux-geode@lists.infradead.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is actually defined in include/crypto/aes.h , no need to have
a a different symbol for the same thing twice.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: Michal Ludvig <michal@logix.cz>
Cc: Varun Wadekar <vwadekar@nvidia.com>
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: linux-geode@lists.infradead.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This tree has already been added to Stephen Rothwell's list for
linux-next. Make it visible in the MAINTAINERS file as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
DT-enabled Dove moved over from ARCH_DOVE in mach-dove to MACH_DOVE in
mach-mvebu. As non-DT ARCH_DOVE will stay to rot for a while, add a new
DT-only MACH_DOVE Kconfig. This slipped through the cracks and now is
a fix to allow to build Dove's SDHCI driver for mach-mvebu on v3.15-rc.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The SD Host Controller spec states that the SD Host Controller can
request that the driver send up to 40 CMD19's while doing tuning
and that the total time the card spends responding must be < 150ms.
The sdhci_execute_tuning() function in sdhci.c that loops through
sending the CMD19's has multiple bugs. First it sets a "timeout"
variable to 150 and a loop counter variable to 40. It then decrements
both variables by 1 at the end of each loop. It tries to handle
violations of the count and time by doing a break when BOTH variables
are equal to zero, which can never happen because they we set to
different values and decremented by 1 at the same time. The timeout
variable is not based on time at all and is totally useless.
The routine also considers a loop counter of zero to be an error
which means that any controller that requests the max of 40 CMD19s
will cause tuning to fail and be disabled.
I've fixed these issues by allowing up to 40 CMD19's and I've removed
any attempt to handle the 150ms time limit. Removing timeout checking
seems safe here because each CMD19 is timeout protected and the max
loop counters insures we don't loop forever. Adding timeout checking
would not be as simple as snapping the time at the loop start and
checking for 150ms to pass because the loop queues the CMD19's and
uses events to wait for completion so the time would include
all the normal scheduler latencies.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Add O2Micro/BayHubTech chip 8520 subversion B1 SD3.0 support.
Add O2Micro/BayHubTech chip 8620 and 8621 SD3.0 support
Enable Led function of 8520 chip.
Signed-off-by: Peter Guo <peter.guo@bayhubtech.com>
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
moving dmaengine consumer specific function to omap-dmaengine.h
to Resolve build failure seen with sh-allmodconfig:
include/linux/omap-dma.h:171:8: error: expected identifier before numeric constant
make[4]: *** [drivers/mmc/host/omap_hsmmc.o] Error 1
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Check for set block count command fails always since host->cmd is set
to NULL in the same function incorrectly. Correct host->cmd usage properly.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
With devm_ioremap_resource conversion release_mem_region, iounmap can be
removed in clean up path
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
With devm_request_threaded_irq conversion free_irq can be removed
in clean up path
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
With devm_request_irq conversion free_irq can be removed in clean up path
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
With devm_clk_get conversion clk_put can be removed in clean up path
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The Allwinner sunxi mmc host uses dma in bus-master mode using a built-in
designware idmac controller, which is identical to the one found in the
mmc-dw hosts. However the rest of the host is not identical to mmc-dw, it
deals with sending stop commands in hardware which makes it significantly
different from the mmc-dw devices.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
[hdegoede@redhat.com: various cleanups and fixes]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Also uses NSEC_PER_SEC and USEC_PER_SEC instead of hard-coded value.
This makes the intention more clear.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Data errors are completely expected during tuning. Printing them out
is confusing people looking at the kernel logs. They see things like:
[ 3.613296] dwmmc_exynos 12200000.dwmmc0: data error, status 0x00000088
...and they think something is wrong with their hardware.
Remove the printouts. We'll leave it up to a higher level to report
about errors.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Track whether preset mode is currently enabled in hardware, and use that
when making decisions elsewhere in the code rather than reading the
register and checking the bit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Move the remaining parts of the power handling in sdhci_do_set_ios()
into sdhci_set_power().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Move the regulator handling into sdhci_set_power() rather than being in
sdhci_do_set_ios(). This wraps all power control up into this function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
sdhci-tegra provides a get_ro method, which overrides the checking
of the write protect bit in the PRESENT_STATE register in sdhci.c:
if (host->flags & SDHCI_DEVICE_DEAD)
is_readonly = 0;
else if (host->ops->get_ro)
is_readonly = host->ops->get_ro(host);
else
is_readonly = !(sdhci_readl(host, SDHCI_PRESENT_STATE)
& SDHCI_WRITE_PROTECT);
This means it's pointless detecting accesses to this register and
manually setting the SDHCI_WRITE_PROTECT as it has no effect.
This means that the whole of tegra_sdhci_readl() can be removed and
we can use the builtin sdhci readl functionality here.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The only user (sdhci-of-esdhc) no longer uses these callbacks, so lets
remove them to discourage any further use.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
We don't need these hooks in order to insert code in these paths, we
can just provide our own handlers and call the main sdhci handlers as
appropriate.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
We no longer need to emulate the uhs_mode field of the host control2
register - the main sdhci driver never reads this back to evaluate
the current mode as it caches the current mode instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Clean up the code in sdhci_execute_tuning() so the decision whether
to execute tuning is clearer - and despite this reflecting what the
original code was doing, it shows that it may not be what the author
actually intended.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than reading back the timing information from the registers,
cache it locally. This allows implementations to translate the UHS
timing by overriding the set_uhs_signaling() method as required
without also having to emulate the SDHCI_HOST_CONTROL2 register.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Add sdhci_set_uhs_signaling() and always call the set_uhs_signaling
method. This avoids quirks being added into sdhci_set_uhs_signaling().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
FIFO underruns don't generate an interrupt on gmch platforms, so we
should check whether there were any that we failed to notice when
we're disabling FIFO underrun reporting.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Noticed by Thierry Reding in his review, but I've merged the drm
vblank rework topic branch a bit too quickly. So separate fixup.
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ascii art version of the DPIO diagram gets mangled by docbook, so
we can't use it there. Insted provide another version built using
<table>.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Document the internal structure of the VLV display PHY a bit to help
people understand how the different register blocks relate to each
other.
v2: Add a bit more text
Make it a DOC: comment, but leave the ascii art out since
it would get mangled
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
for proper refcounting to take place as we use
i915_add_request() for it.
i915_add_request() also takes the context for the request
from ring->last_context so move the null state batch
submission after the ring context has been set.
v2: we need to check for correct ring now (Ville Syrjälä)
v3: no need to expose i915_gem_move_object_to_active (Chris Wilson)
v4: cargoculted vma/active/inactive error handling removed (Chris Wilson)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This simple patch adds support for raid6 to the ORE.
Most operations and calculations where already for the general
case. Only things left:
* call async_gen_syndrome() in the case of raid6
(NOTE that the raid6 math is the one supported by the Linux Kernel
see: crypto/async_tx/async_pq.c)
* call _ore_add_parity_unit() twice with only last call generating
the redundancy pages.
* Fix couple BUGS in old code
a. In reads when parity==2 it can happen that per_dev->length=0
but per_dev->offset was set and adjusted by _ore_add_sg_seg().
Don't let it be overwritten.
b. The all 'cur_comp > starting_dev' thing to determine if:
"per_dev->offset is in the current stripe number or the
next one."
Was a complete raid5/4 accident. When parity==2 this is not
at all true usually. All we need to do is increment si->ob_offset
once we pass by the first parity device.
(This also greatly simplifies the code, amen)
c. Calculation of si->dev rotation can overflow when parity==2.
* Then last enable raid6 in ore_verify_layout()
I want to deeply thank Daniel Gryniewicz who found first all the
bugs in the old raid code, and inspired these patches:
Inspired-by Daniel Gryniewicz <dang@linuxbox.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Two cleanups:
* si->cur_comp, si->cur_pg where always calculated after
the call to ore_calc_stripe_info() with the help of
_dev_order(...). But these are already calculated by
ore_calc_stripe_info() and can be just set there.
(This is left over from the time that si->cur_comp, si->cur_pg
were only used by raid code, but now the main loop manages
them anyway even though they are ultimately not used in
none raid code)
* si->cur_comp - For the very last stripe case, was set inside
_ore_add_parity_unit(). This is not clear and will be wrong
for coming raid6 so move this to only caller. Now si->cur_comp
is only manipulated within _prepare_for_striping(), always next
to the manipulation of cur_dev.
Which is much easier to understand and follow.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
