Add SD/MMC driver for MOXA ART SoCs.
The "MOXA ART MMC controller" is likely a faraday "ftsdc010",
a controller with support in U-Boot:
http://git.denx.de/?p=u-boot.git;a=blob;f=drivers/mmc/ftsdc010_mci.c
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Realtek USB SD/MMC host driver provides mmc host support based on the
Realtek USB card reader MFD driver.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
NUM_GPIOS is not used after e19499ae10 ("mmc: sdhci-s3c: let device
core setup the default pin configuration"). Thus remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Restore the card-present checking point.
(The following part was removed from commit bf626e5 ("mmc: dw_mmc:
use slot-gpio to handle cd pin")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Since using the device-tree, didn't use the callback pointer.
So removed the unused callback pointer.
When the set_power callback is used, it should be added in future.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
It's right to check immediately whether host->bus_hz is assigned or not.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
mmc_of_parse() have been already parsed the general capability.
Didn't need to use the local parser.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Replace existing resource handling in the driver with managed
device resource, this ensures more consistent error values and
simplifies error paths.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
We may read an unexpected value when detemining which codec is attached.
In that case, either a unsupported codec is attached or something wrong
with I2C. The driver will not work properly on both cases. So we return
an error for that.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This was initially removed in commit 6423c1875 ("ASoC: Remove runtime field from
DAI"), but was, presumably by accident, brought back in commit f0fba2ad1 ("ASoC:
multi-component - ASoC Multi-Component Support"). But has never been
initialized to anything but NULL ever since. This commit removes it again.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Suspend/resume support for the atmel-pcm-pdc driver was broken in commit
f0fba2ad1 ("ASoC: multi-component - ASoC Multi-Component Support"). It
essentially reverted the modifications done in commit 10cab262 ("ASoC: Change
how suspend and resume obtain the PCM runtime"). The suspend and resume handlers
at the beginning check if dai->runtime is not NULL, but dai->runtime is always
NULL, hence the code never runs. Considering that nobody noticed any problems in
the last 4 years since the code was broken and that the driver does not set
SNDRV_PCM_INFO_RESUME, which means applications are expected to stop and restart
the audio stream during suspend/resume, it is probably safe to assume that his
code is not needed and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently when the DAPM context bias level is SUSPEND and the target bias level
is OFF dapm_pre_sequence_async() will first transition to PREPARE and
dapm_post_sequence_async() will then transition back from PREPARE to STANDBY and
then to OFF.
This patch makes sure that dapm_pre_sequence_async() only transitions to PREPARE
when either going to ON or away from ON. This avoids the extra unnecessary
transitions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
In case we are doing DMA transfer and the size of the buffer is not multiple
of 4 bytes the driver truncates that to 4-byte boundary and tries to handle
remaining bytes using PIO.
Or that is what it tried to do. What actually happens is that it calls
ALIGN() to the buffer size which aligns it to the next 4-byte boundary
(doesn't truncate). Doing this results 1-3 bytes extra to be transferred.
Furthermore we handle remaining bytes using PIO which results one extra
byte to be transferred. In worst case the driver transfers 4 extra bytes.
While investigating this it turned out that the DMA hardware doesn't even
have such limitation so we can solve this by dropping the code that tries
to handle unaligned bytes.
Reported-by: Chiau Ee Chew <chiau.ee.chew@intel.com>
Reported-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The dw_spi_cleanup() function was removed by commit c63f5da008
"spi: dw: Don't call kfree for memory allocated by devm_kzalloc".
commit ec37e8e1f0 "spi: dw: migrate to generic queue infrastructure" added
dw_spi_cleanup() but never use it. So now I got below build warning:
CC [M] drivers/spi/spi-dw.o
drivers/spi/spi-dw.c:609:13: warning: 'dw_spi_cleanup' defined but not used [-Wunused-function]
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since there is no support for compressed audio in Baytrail ADSP firmware
there is no need to leave it on during suspend since ALSA PCM buffers are
too small for leaving ADSP on for playing or recording.
Implement PM callbacks to Baytrail byt-rt5640.c machine driver that call
snd_soc_suspend and snd_soc_resume functions and unset the ignore_suspend
fields in DAI links.
This makes soc-core and ALSA core gracefully suspend and resume active
stream and call sst_byt_pcm_trigger() during suspend-resume cycle.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add suspend and resume support to Baytrail SST DSP. This is implemented by
unloading firmware modules and putting DSP into reset prior suspend and
restarting DSP again in normal boot state after resume.
Context restore for running streams is implemented by scheduling a work from
sst_byt_pcm_trigger() that will allocate a stream with existing parameters
and start it from last known buffer position before suspend.
[Jarkko: Squashed together 5 WIP patches from Liam and 1 from me]
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Suspend/resume requires reloading FW to boot state so we need to also make
sure that the driver matches the FW state at boot.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have to save the physical address of extended firmware block in the
beginning of mailbox every time when we boot the DSP firmware since that
mailbox address is re-used after DSP firmware is running. Otherwise DSP
firmware will get bogus extended firmware block address during next DSP
boot.
Currently this is not problem but becomes when DSP runtime rebooting is
implemented. Prepare for that by moving extended firmware address saving
from sst_byt_init() to sst_byt_boot().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Stream start position will be needed in resume code. Prepare for it by
adding start offset argument to sst_byt_stream_start().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Baytrail ADSP stream IPC simplifies a little by moving IPC_IA_START_STREAM
construction and sending directly into sst_byt_stream_start() from
sst_byt_stream_operations(). This is because IPC_IA_START_STREAM is only
stream IPC with extra message data so this move saves a few code lines.
Main motivation for this is to prepare for passing stream start position
to sst_byt_stream_start() which will be needed in resume code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is for preparing suspend/resume support but can give also more
safeguard against concurrent timestamp structure access between DSP firmware
and host.
Now DSP DMA pointer is sampled in each pcm pointer callback in
sst_byt_pcm_pointer() but that is unneeded since DSP updates the timestamp
period basis and can potentially be racy if sst_byt_pcm_pointer() is called
when DSP is updating the timestamp.
By taking DSP DMA pointer only after period elapsed IPC messages in
byt_notify_pointer() and returning stored hw pointer in
sst_byt_pcm_pointer() there is less risk for concurrent access.
The same stored hw pointer can be also used in suspend/resume code for
restarting the stream at the same position.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit commit de9ba98b6d ("ASoC: dapm: Make widget power register settings more
flexible") added generic support for on_val/off_val in the DAPM core. With this
in place there is no need anymore for having a special event callback for
SND_SOC_DAPM_REG() widgets.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
If we find a widget who's stream name matches the name of a DAI widget then
thats the one it should be connected to. Based on the widget id we can say in
which direction the path should be. No need to go back to the DAI and check the
stream names.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We already know the widgets we want to connect, so use snd_soc_dapm_add_path()
instead of snd_soc_dapm_add_route() in snd_soc_dapm_new_pcm().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We already know which two widgets should be connected, so use
snd_soc_dapm_add_path() instead of snd_soc_dapm_add_route() in
snd_soc_dapm_connect_dai_link_widgets().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This reverts commit bd23c5b661.
The patch claims that the patch is necessary to avoid double prefix addition
when calling snd_soc_dapm_add_route() from snd_soc_dapm_connect_dai_link_widgets().
But snd_soc_dapm_add_route() is called with the card's DAPM context, which does
not have a prefix, which means there is no prefix that could be added a second
time.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
For CODEC to CODEC DAI links the paths are created in snd_soc_dapm_new_pcm().
Also for CODEC to CODEC links the widgets are connected cross-over via a DAI
link widget, meaning that the capture widget of one CODEC will be connected to
the playback widget of the other and vice versa. Whereas
snd_soc_dapm_connect_dai_link_widgets() directly connects the playback widget of
the CPU DAI to the playback widget of the CODEC DAI and the capture widget of
the CPU DAI to the capture widget of the CODEC DAI. So not skipping
CODEC<->CODEC links in snd_soc_dapm_connect_dai_link_widgets() will create
incorrect connections between the two CODECs which will cause DAPM to detect
active paths where there are none and unnecessarily power up widgets.
Fixes: b893ea5 ("ASoC: sapm: Automatically connect DAI link widgets in DAPM graph.")
Cc: <stable@vger.kernel.org> (for 3.14+)
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Spansion s25sl032p supports Dual and Quad SPI transfers, hence set the
SPI_NOR_DUAL_READ and SPI_NOR_QUAD_READ flags.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Commit 03e296f613 ("mtd: m25p80: use the SPI
nor framework") accidentally removed support for Dual SPI read transfers.
Add it back.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fixes:
drivers/mtd/devices/elm.c:480:12: warning: 'elm_suspend' defined but not used [-Wunused-function]
drivers/mtd/devices/elm.c:488:12: warning: 'elm_resume' defined but not used [-Wunused-function]
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The regular state before we execute SNDRV_PCM_TRIGGER_SUSPEND should be
SNDRV_PCM_TRIGGER_START, not SNDRV_PCM_TRIGGER_STOP. Thus fix it.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Building this driver on ARM/at91 always gives us this error message:
drivers/input/touchscreen/atmel-wm97xx.c:63:2: error: #error Unknown CPU, this driver only supports AT32AP700X CPUs.
Clearly this configuration is not meant to work, so let's just prevent
it in Kconfig. If we ever want to use it on another platform, we should
also pass proper resources for GPIO, IRQ and memory, which are hardcoded
to AT32AP700X at the moment.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ps2 mouse and keyboard drivers use the "serio" framework that they
correctly select in Kconfig, and that in turn depends on the i8042 driver,
which is also allowed to be disabled for architectures that don't have an
i8042.
However, Kconfig also allows i8042 to be built as a module while
the serio framework is built-in, which causes this link error:
drivers/built-in.o: In function `ps2_begin_command':
:(.text+0x26b6cc): undefined reference to `i8042_check_port_owner'
:(.text+0x26b6d4): undefined reference to `i8042_lock_chip'
drivers/built-in.o: In function `ps2_end_command':
:(.text+0x26b734): undefined reference to `i8042_check_port_owner'
:(.text+0x26b73c): undefined reference to `i8042_unlock_chip'
On x86, a specific 'select SERIO_I8042' takes care of it, but
not on the other architecture that potentially have a i8042.
This patch changes the Kconfig logic to ensure that whenever
there is an i8042, it does get used for the serio driver, avoiding
the link error above.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
trace_sched_wakeup(.success) is a dead argument and has been for ages,
the only reason its still there is because of brain dead software, which
apparently includes perf tools
There's a few more instances in pearly snake shit, but that's not
supported as far as I care anyhow, so let that bitrot.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140512181946.GG13467@laptop.programming.kicks-ass.net
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
If the sfc driver is in legacy interrupt mode (either explicitly by
using interrupt_mode module param or by falling back to it) it will
hit a warning at kernel/irq/manage.c because it will try to free an irq
which wasn't allocated by it in the first place because the MSI(X) irqs are
zero and it'll try to free them unconditionally. So fix it by checking if
we're in legacy mode and freeing the appropriate irqs.
CC: Zenghui Shi <zshi@redhat.com>
CC: Ben Hutchings <ben@decadent.org.uk>
CC: <linux-net-drivers@solarflare.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: David S. Miller <davem@davemloft.net>
Fixes: 1899c111a5 ("sfc: Fix IRQ cleanup in case of a probe failure")
Reported-by: Zenghui Shi <zshi@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anyone working with an AMD Elan SC520 development or evaluation board
would be building a dedicated kernel for it, so we can make the
sc520cdp and netsc520 maps depend on MELAN. SC520_CPUFREQ already
depends on MELAN so it makes things more consistent. It also makes
kernel configuration for every other x86 user easier.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When I use the following command, eth0 cannot send any packets.
#tc qdisc add dev eth0 root handle 1: hhf limit 1
Because qlen need be smaller than limit, all packets were dropped.
Fix this by qlen *<=* limit.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __vlan_find_dev_deep should always called in RCU, according
David's suggestion, rename to __vlan_find_dev_deep_rcu looks more
reasonable.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearing the IFF_ALLMULTI flag on a down interface could cause an allmulti
overflow on the underlying interface.
Attempting the set IFF_ALLMULTI on the underlying interface would cause an
error and the log message:
"allmulti touches root, set allmulti failed."
Signed-off-by: Peter Christensen <pch@ordbogen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix iovar 'bw_cap' set command failure introduced by
commit ff3b0fba6f25555ef59c55d138a467d0f81d82d7
Author: Arend van Spriel <arend@broadcom.com>
Date: Sat Mar 15 12:00:57 2014 +0100
brcmfmac: fallback to mimo_bw_cap for older firmwares
This resulted in disabling 20MHz operation in the firmware.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Regression of 346874c9: PAE is set in long mode, but that does not mean
we have valid PDPTRs.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As suggested by several people, rename local_df to ignore_df,
since it means "ignore df bit if it is set".
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
