The ST Micro variant supports the option of using a feedback clock signal in
favor of the clockout pin when latching incoming signals on the data bus.
Since this is matter of how pins are being routed we need to provide a new DT
binding to be able to configure this through DT.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Some variants have support for indicating the bus signal directions,
which currently are configured through platform data.
Add corresponding DT bindings to enable us to move away from using the
platform data.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
To avoid duplication of code while handling card detect and write
protect GPIO pins/irqs, let's convert to use the mmc gpio API.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For CONFIG_PM_SLEEP, the device were always left in full power state
after system suspend.
We solely relied on a power domain to put it into low power state,
which is an unreasonable requirement to put on SOCs to implement.
Especially for those SOCs not supporting power domains at all.
Use pm_runtime_force_suspend|resume() as the system suspend callbacks,
to resolve the issue.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Convert to the SET_PM_RUNTIME_PM macro while defining the runtime PM
callbacks. This means the callbacks becomes available for both
CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME, which is needed to handle the
combinations of these scenarios.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In runtime suspended state, we are not expecting IRQs and thus we can
safely mask them, not only for pwrreg_nopower variants but for all.
Obviously we then also need to make sure we restore the IRQ mask while
becoming runtime resumed.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
virt_to_pfn has been defined in arch/arm/include/asm/memory.h by commit
e26a9e0 "ARM: Better virt_to_page() handling" and Xen has come to rely
on it. Introduce virt_to_pfn on arm64 too.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
I believe that passing pid (instead of tid) as the 3rd arg of the
machine__find*_thread() was to find a main thread so that it can
search proper map group for symbols. However with the map sharing
patch applied, it now can do it in any thread.
It fixes a bug when each thread has different name, it only reports a
main thread for samples in other threads.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: David Ahern <dsahern@gmail.com>
Acked-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1399856202-26221-1-git-send-email-namhyung@kernel.org
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
The on_exit() function was only used in perf record but it's gone in
previous patch.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Stephane Eranian <eranian@google.com>
Cc: Bernhard Rosenkraenzer <Bernhard.Rosenkranzer@linaro.org>
Cc: Irina Tirdea <irina.tirdea@intel.com>
Link: http://lkml.kernel.org/r/1399855645-25815-2-git-send-email-namhyung@kernel.org
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Currently perf record doesn't propagate the exit status of a workload
given by the command line. But sometimes it'd useful if it's
propagated so that a monitoring script can handle errors
appropriately.
To do that, it moves most of logic out of the exit handlers and run
them directly in the __cmd_record(). The only thing needs to be done
in the handler is propagating terminating signal so that the shell can
terminate its loop properly when Ctrl-C was pressed. Also it cleaned
up the resource management code in record__exit().
With this change, perf record returns the child exit status in case of
normal termination and send signal to itself when terminated by signal.
Example run of Stephane's case:
$ perf record true && echo yes || echo no
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.013 MB perf.data (~589 samples) ]
yes
$ perf record false && echo yes || echo no
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.013 MB perf.data (~589 samples) ]
no
Jiri's case (error in parent):
$ perf record -m 10G true && echo yes || echo no
rounding mmap pages size to 17179869184 bytes (4194304 pages)
failed to mmap with 12 (Cannot allocate memory)
no
$ ulimit -n 6
$ perf record sleep 1 && echo yes || echo no
failed to create 'go' pipe: Too many open files
Couldn't run the workload!
no
And Peter's case (interrupted by signal):
$ while :; do perf record sleep 1; done
^C[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.014 MB perf.data (~593 samples) ]
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Stephane Eranian <eranian@google.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@kernel.org>
Link: http://lkml.kernel.org/r/1399855645-25815-1-git-send-email-namhyung@kernel.org
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
In output of perf sched map, any shortname of thread will be explained
at the first time when it appear.
Example:
*A0 228836.978985 secs A0 => perf:23032
*. A0 228836.979016 secs B0 => swapper:0
. *C0 228836.979099 secs C0 => migration/3:22
*A0 . C0 228836.979115 secs
A0 . *. 228836.979115 secs
But B0, which is explained as swapper:0 did not appear in the
left part of output. Instead, we use '.' as the shortname of
swapper:0. So the comment of "B0 => swapper:0" is not easy to
understand.
This patch clarify the output of perf sched map with not allocating
one letter-number shortname for swapper:0 and print ". => swapper:0"
as the explanation for swapper:0.
Example:
*A0 228836.978985 secs A0 => perf:23032
* . A0 228836.979016 secs . => swapper:0
. *B0 228836.979099 secs B0 => migration/3:22
*A0 . B0 228836.979115 secs
A0 . * . 228836.979115 secs
A0 *C0 . 228836.979225 secs C0 => ksoftirqd/2:18
A0 *D0 . 228836.979236 secs D0 => rcu_sched:7
Signed-off-by: Dongsheng <yangds.fnst@cn.fujitsu.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Link: http://lkml.kernel.org/r/1399354741-19522-1-git-send-email-yangds.fnst@cn.fujitsu.com
[ small style fixes to make checkpatch happy ]
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
We should record and process sched:sched_wakeup_new event in
perf sched tool, but currently, there is the process function
for it, without recording it in record subcommand.
This patch add -e sched:sched_wakeup_new to perf sched record.
Signed-off-by: Dongsheng <yangds.fnst@cn.fujitsu.com>
Link: http://lkml.kernel.org/r/710c6edd2162b2cea1711443f54de47c0210d9fd.1399273302.git.yangds.fnst@cn.fujitsu.com
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
We need to use the mark we get from the tunnels o_key to
lookup the right vti state in the error handlers. This patch
ensures that.
Fixes: df3893c1 ("vti: Update the ipv4 side to use it's own receive hook.")
Fixes: fa9ad96d ("vti6: Update the ipv6 side to use its own receive hook.")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Remove the now unused r8a7791_init_early() function.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Convert the Koelsch board support to use shmobile_init_delay()
to be able to migrate away from per-SoC delay setup functions.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Convert the common C-code-less r8a7791 DT board support
to use shmobile_init_delay() to be able to migrate away
from per-SoC delay setup functions.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
If the kernel is built to support multi-ARM configuration with shmobile
support built in, then drivers/sh is not built. This contains the PM
runtime code in drivers/sh/pm_runtime.c, which implicitly enables the
module clocks for all devices, and thus is quite essential.
Without this, the state of clocks depends on implicit reset state, or on
the bootloader.
If ARCH_SHMOBILE_MULTI then build the drivers/sh directory, but ensure that
bits that may conflict (drivers/sh/clk if the common clock framework is
enabled) or are not used (drivers/sh/intc), are not built.
Also, only enable the PM runtime code when actually running on a shmobile
SoCs that needs it.
ARCH_SHMOBILE_MULTI was added a while ago by commit
efacfce5f8 ("ARM: shmobile: Introduce
ARCH_SHMOBILE_MULTI"), but drivers/sh was compiled for both
ARCH_SHMOBILE_LEGACY and ARCH_SHMOBILE_MULTI until commit
bf98c1eac1 ("ARM: Rename ARCH_SHMOBILE to
ARCH_SHMOBILE_LEGACY").
Inspired by a patch from Ben Dooks <ben.dooks@codethink.co.uk>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
If we fail to register one of the xfrm protocol handlers we will
unregister the pernet ops twice on the error exit path. This will
probably lead to a kernel panic as the double deregistration
leads to a double kfree().
Fix this by removing one of the calls to do it only once.
Fixes: fa9ad96d49 ("vti6: Update the ipv6 side to use its own...")
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
the parameter rt will be assigned to c.arg in function fib6_clean_tree(),
but function fib6_prune_clone() doesn't use c.arg, so we can remove it
safely.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change ensures the driver can be built successfully without the
CONFIG_SYSFS flag.
MS-TFS: 182270
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I am seeing an issue where a CPU running perf eventually hangs.
Traces show timer interrupts happening every 4 seconds even
when a userspace task is running on the CPU. /proc/timer_list
also shows pending hrtimers have not run in over an hour,
including the scheduler.
Looking closer, decrementers_next_tb is getting set to
0xffffffffffffffff, and at that point we will never take
a timer interrupt again.
In __timer_interrupt() we set decrementers_next_tb to
0xffffffffffffffff and rely on ->event_handler to update it:
*next_tb = ~(u64)0;
if (evt->event_handler)
evt->event_handler(evt);
In this case ->event_handler is hrtimer_interrupt. This will eventually
call back through the clockevents code with the next event to be
programmed:
static int decrementer_set_next_event(unsigned long evt,
struct clock_event_device *dev)
{
/* Don't adjust the decrementer if some irq work is pending */
if (test_irq_work_pending())
return 0;
__get_cpu_var(decrementers_next_tb) = get_tb_or_rtc() + evt;
If irq work came in between these two points, we will return
before updating decrementers_next_tb and we never process a timer
interrupt again.
This looks to have been introduced by 0215f7d8c5 (powerpc: Fix races
with irq_work). Fix it by removing the early exit and relying on
code later on in the function to force an early decrementer:
/* We may have raced with new irq work */
if (test_irq_work_pending())
set_dec(1);
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix kconfig warnings:
PTP_1588_CLOCK selects NET_PTP_CLASSIFY, which depends on NET,
so PTP_1588_CLOCK should also depend on NET.
PTP_1588_CLOCK_PCH selects PTP_1588_CLOCK so the former should
depend on NET.
warning: (IXP4XX_ETH && PTP_1588_CLOCK) selects NET_PTP_CLASSIFY which has unmet direct dependencies (NET)
warning: (SFC && TILE_NET && BFIN_MAC_USE_HWSTAMP && TIGON3 && FEC && E1000E && IGB && IXGBE && I40E && MLX4_EN && SXGBE_ETH && STMMAC_ETH && TI_CPTS && PTP_1588_CLOCK_GIANFAR && PTP_1588_CLOCK_IXP46X && DP83640_PHY && PTP_1588_CLOCK_PCH) selects PTP_1588_CLOCK which has unmet direct dependencies (NET)
[This warning is caused by the new 'depends on NET' in PTP_1588_CLOCK.]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
BPF testsuite and cleanup
This patchset adds BPF testsuite and improves readability of classic
to internal BPF converter.
The testsuite helped to find 'negative offset bug' in x64 JIT that was
fixed by commit fdfaf64e ("x86: bpf_jit: support negative offsets")
It can be very useful for classic and internal JIT compiler developers.
Also it serves as performance benchmark.
x86_64/i386 pass all tests with and without JIT. arm32 JIT is failing
negative offset tests which are unsupported.
Internal BPF tests are much larger than classic tests to cover different
combinations of registers. Negative tests check correctness of classic
BPF verifier which must reject them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The testsuite covers classic and internal BPF instructions.
It is particularly useful for JIT compiler developers.
Adds to "net" selftest target.
The testsuite can be used as a set of micro-benchmarks.
It measures execution time of each BPF program in nsec.
This patch adds core framework.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce BPF helper macros to define instructions
(similar to old BPF_STMT/BPF_JUMP macros)
Use them while converting classic BPF to internal
and in BPF testsuite later.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One can logically expect that when the user has specified "nordrand",
the user doesn't want any use of the CPU random number generator,
neither RDRAND nor RDSEED, so disable both.
Reported-by: Stephan Mueller <smueller@chronox.de>
Cc: Theodore Ts'o <tytso@mit.edu>
Link: http://lkml.kernel.org/r/21542339.0lFnPSyGRS@myon.chronox.de
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Remove a few OMAP34XX_CM_REGADDR defines and replace these with offset
based register accesses instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Resetting root port has more stuff to do than that for PCIe switch
ports and we should have resetting root port done in firmware instead
of the kernel itself. The problem was introduced by commit 5b2e198e
("powerpc/powernv: Rework EEH reset").
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A documentation update exposed that there is a separate set of VID
values that must be used in the turbo/boost P state range. Add
enumerating and setting the correct VID for P states in the turbo
range.
Cc: v3.13+ <stable@vger.kernel.org> # v3.13+
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Chromebooks (at least Acer C720 and Pixel) implement an ACPI object
for TPM, but don't implement the _DSM method to support PPI. As
a result, the TPM driver fails to load on those machines after
commit 1569a4c4ce (ACPI / TPM: detect PPI features by checking
availability of _DSM functions) which causes them to fail to
resume from system suspend, becuase they require the TPM hardware
to be put into the right state during resume and the TPM driver
is necessary for that.
Fix the problem by making tpm_add_ppi() return 0 when tpm_ppi_handle
is still NULL after walking the ACPI namespace in search for the PPI
_DSM, which allows the TPM driver to load and operate the hardware
(during system resume in particular), but avoid creating the PPI
sysfs group in that case.
This change is based on a prototype patch from Jiang Liu.
Fixes: 1569a4c4ce (ACPI / TPM: detect PPI features by checking availability of _DSM functions)
References: https://bugzilla.kernel.org/show_bug.cgi?id=74021
Reported-by: James Duley <jagduley@gmail.com>
Reported-by: Phillip Dixon <phil@dixon.gen.nz>
Tested-by: Brandon Casey <drafnel@gmail.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There's an extra newline that shouldn't be there - remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cleanup the legacy Armadillo board code slightly by
removing the pointless eva_add_early_devices() function
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove the now unused r8a7740_init_delay() function.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Tested-by: Geert Uytterhoeven <geert@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Convert the Armadillo r8a7740 DT reference board support
to use shmobile_init_delay() to be able to migrate away
from per-SoC delay setup functions.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Tested-by: Geert Uytterhoeven <geert@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Convert the common C-code-less r8a7740 DT board support
to use shmobile_init_delay() to be able to migrate away
from per-SoC delay setup functions.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Tested-by: Geert Uytterhoeven <geert@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add 800 MHz to the r8a7740 DTS to describe the maximum CPU frequency.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Tested-by: Geert Uytterhoeven <geert@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The MTU2 (Multi-Function Timer Pulse Unit 2) driver implements a new
style of platform data that handles the timer as a single device with
multiple channel. Switch from the old-style platform data to the
new-style platform data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
