There is a missing 0 entry from the MOD_SEL3 table.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The quirk registers mechanism which allows register to have a static read
access value from the sensor specific quirks, is not used. Remove it. It is
to be replaced by a more generic register diversion quirk soon.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The extra entry in the table makes SCIFA0_B, and all
peripherals after it, fail.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Define a new binding for the Qualcomm TLMMv2 based pin controller inside the
IPQ8064.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pinctrl definitions for the GPIO pins of the TLMM v2 block in the
Qualcomm IPQ8064 platform.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since we set up device wake-up interrupts as pinctrl-single
interrupts, we now must use the standard request_irq and
related functions to manage them.
If the pin interrupts are enabled for some pins at boot,
the wake-up events can show up as constantly pending
at least on omaps and will hang the system unless the related
device driver clears the event at the device.
To fix this, let's clear the interrupt flags during init,
and print out a warning so the board maintainers can update
their drivers to do proper request_irq for the driver specific
wake-up events.
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
List all sunxi pinctrl compatible strings in order to be able to grep for
those values.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement support for the VSP1 DT bindings in the VSP1 driver. The
driver now first retrieves platform data either from the platform data
pointer or by reading the device tree node, and then validates it
regardless of the platform data source.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All parameters supplied through platform data can now be passed through
the device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The Blend ROP Unit performs blending and ROP operations for up to four
sources.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Scaling of the alpha layer is disabled as both the RPF and WPF are
configured to hardcode the alpha value to 255. This results in a 0 alpha
value at the UDS output, making the image invisible when alpha blended
in the BRU. Fix it by enabling scaling of the alpha layer.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The VSP1 has no rt clock. Remove them from the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When compiling this for older kernels using the compatibility build
the compiler complains about uninitialized variables:
In file included from include/linux/kernel.h:20:0,
from include/linux/cache.h:4,
from include/linux/time.h:7,
from include/linux/input.h:13,
from /home/hans/work/build/media_build/v4l/compat.h:9,
from <command-line>:0:
/home/hans/work/build/media_build/v4l/videobuf2-core.c: In function 'vb2_mmap':
include/linux/dynamic_debug.h:60:9: warning: 'plane' may be used uninitialized in this function [-Wmaybe-uninitialized]
printk(KERN_DEBUG pr_fmt(fmt), ##__VA_ARGS__); \
^
/home/hans/work/build/media_build/v4l/videobuf2-core.c:2381:23: note: 'plane' was declared here
unsigned int buffer, plane;
^
In file included from include/linux/kernel.h:20:0,
from include/linux/cache.h:4,
from include/linux/time.h:7,
from include/linux/input.h:13,
from /home/hans/work/build/media_build/v4l/compat.h:9,
from <command-line>:0:
include/linux/dynamic_debug.h:60:9: warning: 'buffer' may be used uninitialized in this function [-Wmaybe-uninitialized]
printk(KERN_DEBUG pr_fmt(fmt), ##__VA_ARGS__); \
^
/home/hans/work/build/media_build/v4l/videobuf2-core.c:2381:15: note: 'buffer' was declared here
unsigned int buffer, plane;
^
While these warnings are bogus (the call to __find_plane_by_offset will
set buffer and plane), it doesn't hurt to initialize these variables.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The stop_streaming op is only called if streaming is in progress,
so drop the unnecessary 'if (!vb2_is_streaming(vq))' check.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The vb2 core ignores any return code from the stop_streaming op.
And there really isn't anything it can do anyway in case of an error.
So change the return type to void and update any drivers that implement it.
The int return gave drivers the idea that this operation could actually
fail, but that's really not the case.
The pwc amd sdr-msi3101 drivers both had this construction:
if (mutex_lock_interruptible(&s->v4l2_lock))
return -ERESTARTSYS;
This has been updated to just call mutex_lock(). The stop_streaming op
expects this to really stop streaming and I very much doubt this will
work reliably if stop_streaming just returns without really stopping the
DMA.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that we have a DMA driver, we can add the DMA bindings in the DTSI for the
controller and the devices supported that can use DMA.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The DT are supposed to be ordered by physical address. Move the NMI node where
it belongs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add support for MAX77836 chipset and its additional two LDO regulators.
These LDO regulators are controlled by the PMIC block with additional
regmap (different I2C slave address).
The MAX77836 charger and safeout regulators are almost identical to
MAX14577. The registers layout is the same, except values for charger's
current. The patch adds simple mapping between device type and supported
current by the charger regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for MAX77836 chipset to the max14577 extcon driver. The
MAX77836 MUIC has additional interrupts (VIDRM, ADC1K) so IRQ handling
is split up into two functions: max14577_parse_irq() and
max77836_parse_irq().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add Maxim 77836 support to max14577 driver. The chipsets have same MUIC
component so the extcon, charger and regulators are almost the same. The
MAX77836 however has also PMIC and Fuel Gauge.
The MAX77836 uses three I2C slave addresses and has additional interrupts
(related to PMIC and Fuel Gauge). It has also Interrupt Source register,
just like MAX77686 and MAX77693.
The MAX77836 PMIC's TOPSYS and INTSRC interrupts are reported in the
PMIC block. The PMIC block has different I2C slave address and uses own
regmap so another regmap_irq_chip is needed.
Since we have two regmap_irq_chip, use shared interrupts on MAX77836.
This patch adds additional defines and functions to the max14577 MFD core
driver so the driver will handle both chipsets. Also this patch replaces
"0x1 << N" with BIT(N) in defines for register masks.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch prepares for adding support for MAX77836 device to existing
max14577 driver by adding MAX14577 prefix to defines of interrupts.
This is only a rename-like patch, new code is not added.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch continues the preparation for adding support for max77836
device to existing max14577 driver.
During probe choose muic_irqs according to device type. Currently there
are only "max14577_muic_irqs" but later patch will add max77836
interrupts.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add max14577 prefix to muic_irqs array. This prepares for max77836
support in this extcon driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch continues the preparation for adding support for MAX77836
device to existing max14577 driver.
Add enum for types of devices supported by this driver. The device type
will be detected by matching of_device_id, or i2c_device_id as a
fallback.
The patch also moves to separate function the code related to displaying
DeviceID register values.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Warnings due to __le16 / u16 conversions.
Replace offending struct and so stay on cpu domain.
Signed-off-by: Robert Butora <robert.butora.fi@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add muic prefix to regmap config to differentiate between another regmap
config for MAX77836 PMIC node. Additionally remove unused
symbols: MAX14577_REG_INVALID and max14577_irq_source.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch use device name to make sysfs path according to device type:
max14577-muic
- /sys/class/extcon/max14577-muic/
max77836-muic
- /sys/class/extcon/max77836-muic/
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
68efd7d2fb("arm: dma-mapping: remove order parameter from
arm_iommu_create_mapping()") is causing kernel panic
because it wrongly sets the value of mapping->size:
Unable to handle kernel NULL pointer dereference at virtual
address 000000a0
pgd = e7a84000
[000000a0] *pgd=00000000
...
PC is at bitmap_clear+0x48/0xd0
LR is at __iommu_remove_mapping+0x130/0x164
Fix it by correcting mapping->size value.
Signed-off-by: Ritesh Harjani <ritesh.harjani@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
External LNA between antenna connector and RF tuner is controlled
by EM28178 GPIO 0. GPIO value 1 is LNA active and value 0 is LNA
disabled.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
bit3 was not cleared always leaving driver reporting demod is not
fully locked. Do not check bit0 as it seems to be always 0.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DVB-C uses lower frequencies than DVB-T. Extend frequency range down to
110 MHz in order to support DVB-C. 110 - 862 MHz range is defined by
NorDig Unified 2.2 specification.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The commit e41975ed (ASoC: core: Fix the DAI name getting) added a break
within the "if (id < 0 || id >= pos->num_dai)" while the original design
of the search didn't break the loop if that condition contented but only
mark the ret error and let it go on to search the next component.
In a case like dmaengine which's not a dai but as a component sharing an
identical name with a dai, both the id and pos->num_dai here could be 0.
If we break the search, we may never find the dai we want as it might be
placed behind its dmaengine in the component list.
So this patch fixes the issue above by following the original design to
let the search carry on.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Silicon Labs Si2157 silicon tuner driver.
Currently it supports only DVB-T.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add the vdd supply to Documentation/devicetree/bindings/sound/ak4104.txt.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The AK4104 has only one power supply, called VDD. Enable it as long as
the codec is in use.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The properties like format, bitclock-master, frame-master,
bitclock-inversion, and frame-inversion should be common to the dais
connected with a dai-link. For bitclock-master and frame-master
properties to be unambiguous they need to indicate the mastering dai
node with a phandle.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
