When testing the ftrace function tracer, I realised that ftrace_caller
and mcount are called from modules and they both call into C, therefore
they need the ABIv2 global entry point to establish r2.
Signed-off-by: Anton Blanchard <anton@samba.org>
If an assembly function that calls back into c code is exported to
modules, we need to ensure r2 is setup correctly. There are only
two places crazy enough to do it (two of which are my fault).
Signed-off-by: Anton Blanchard <anton@samba.org>
ELFv2 doesn't use function descriptors, because it doesn't need to
load a new r2 when calling into a function. On the other hand, you're
supposed to use a local entry point for R_PPC_REL24 branches.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In ELFv2, r12 is supposed to equal to PC on entry to a function.
Our stubs use r11, so change swap that with r12.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
ELFv2 doesn't use function descriptors, so we don't expect symbols to
start with ".". But because depmod and modpost strip ".", and we have
the special symbol ".TOC.", we still need to do it.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The new ELF ABI tends to use R_PPC64_REL16_LO and R_PPC64_REL16_HA
relocations (PC-relative), so implement them.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The kernel resolved the '.TOC.' to a fake symbol, so we need to fix it up
to point to our .toc section plus 0x8000.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
For the ELFv2 ABI, powerpc introduces a magic symbol ".TOC.". If we
don't create a CRC for it (minus the leading ".", since we strip that)
we get a modpost warning about missing CRC and the CRC array seems to
be displaced by 1 so other CRCs mismatch too.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
For the ELFv2 ABI, powerpc introduces a magic symbol ".TOC.". depmod
then complains that this doesn't resolve (so does modpost, but we could
easily fix that). To export this, we need to use asm.
modpost and depmod both strip "." from symbols for the old PPC64 ELFv1
ABI, so we actually export a "TOC.".
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
There is no need to put a function descriptor in
__secondary_hold_spinloop. Use ppc_function_entry to get the
instruction address and put it in __secondary_hold_spinloop instead.
Also fix an issue where we assumed cur_cpu_spec held a function
descriptor.
Signed-off-by: Anton Blanchard <anton@samba.org>
TRACE_WITH_FRAME_BUFFER creates 32 byte stack frames. On ppc64
ABIv1 this is too small and a callee could corrupt the stack by
writing to the parameter save area (starting at offset 48).
Signed-off-by: Anton Blanchard <anton@samba.org>
Some of the assembler files in lib/ make use of the fact that in the
ELFv1 ABI, the caller guarantees to provide stack space to save the
parameter registers r3 ... r10. This guarantee is no longer present
in ELFv2 for functions that have no variable argument list and no
more than 8 arguments.
Change the affected routines to temporarily store registers in the
red zone and/or the top of their own stack frame (in the space
provided to save r31 .. r29, which is actually not used in these
routines).
In opal_query_takeover, simply always allocate a stack frame;
the routine is not performance critical.
Signed-off-by: Ulrich Weigand <ulrich.weigand@de.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Change how we setup registers for ret_from_kernel_thread. In
ABIv1, instead of passing a function descriptor in, dereference
it and pass the target in directly.
Use ppc_global_function_entry to get it right on both ABIv1 and ABIv2.
Signed-off-by: Anton Blanchard <anton@samba.org>
The MMU hashtable and SLB branch patching code uses function
pointers for the update sites. This creates a difference between
ABIv1 and ABIv2 because we don't have function descriptors on
ABIv2.
Get rid of the function pointer and just point at the update
sites directly. This works on both ABIs.
Signed-off-by: Anton Blanchard <anton@samba.org>
To establish addressability quickly, ABIv2 requires the target
address of the function being called to be in r12. Fix a number of
places in assembly code that we do indirect function calls.
We need to avoid function descriptors on ABIv2 too.
Signed-off-by: Anton Blanchard <anton@samba.org>
ABIv2 doesn't have function descriptors or dot symbols. One
new thing it does add is a function global and a local entry
point, so add that to our _GLOBAL macro.
Signed-off-by: Anton Blanchard <anton@samba.org>
There are a few places we have to use dot symbols with the
current ABI - the syscall table and the kvm hcall table.
Wrap both of these with a new macro called DOTSYM so it will
be easy to transition away from dot symbols in a future ABI.
Signed-off-by: Anton Blanchard <anton@samba.org>
STD_EXCEPTION_COMMON, STD_EXCEPTION_COMMON_ASYNC and
MASKABLE_EXCEPTION branch to the handler, so we can remove
the explicit dot symbol and binutils will do the right thing.
Signed-off-by: Anton Blanchard <anton@samba.org>
There is no need to create a function descriptor for the system call
table. By using one we force the system call table into the text
section and it really belongs in the rodata section.
This also removes another use of dot symbols.
Signed-off-by: Anton Blanchard <anton@samba.org>
We have a number of places where we load the text address of a local
function and indirectly branch to it in assembly. Since it is an
indirect branch binutils will not know to use the function text
address, so that trick wont work.
There is no need for these functions to have a function descriptor
so we can replace it with a label and remove the dot symbol.
Signed-off-by: Anton Blanchard <anton@samba.org>
binutils is smart enough to know that a branch to a function
descriptor is actually a branch to the functions text address.
Alan tells me that binutils has been doing this for 9 years.
Signed-off-by: Anton Blanchard <anton@samba.org>
We avoid ABIv2 when building c files since commit b2ca8c89 (powerpc:
Don't use ELFv2 ABI to build the kernel). Do the same for assembly
files.
Signed-off-by: Anton Blanchard <anton@samba.org>
Some Type 1 hypervisors such as XEN won't enable VMX without it present
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This feature emulates the "Acknowledge interrupt on exit" behavior.
We can safely emulate it for L1 to run L2 even if L0 itself has it
disabled (to run L1).
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
For single context invalidation, we fall through to global
invalidation in handle_invept() except for one case - when
the operand supplied by L1 is different from what we have in
vmcs12. However, typically hypervisors will only call invept
for the currently loaded eptp, so the condition will
never be true.
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
1. Further PLL parameter fixes.
2. Fixes for HPD on DP
3. Could of different PM fixes
4. Disabling DPM on RV770
* 'drm-fixes-3.15' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon: don't allow runpm=1 on systems with out ATPX
drm/radeon: fix ATPX detection on non-VGA GPUs
drm/radeon/pm: don't walk the crtc list before it has been initialized (v2)
drm/radeon: properly unregister hwmon interface (v2)
drm/radeon: fix count in cik_sdma_ring_test()
drm/radeon/aux: fix hpd assignment for aux bus
drm/radeon: improve PLL limit handling in post div calculation
drm/radeon: use fixed PPL ref divider if needed
drm/radeon: disable dpm on rv770 by default
When entering an exception after an ICEBP, the saved instruction
pointer should point to after the instruction.
This fixes the bug here: https://bugs.launchpad.net/qemu/+bug/1119686
Signed-off-by: Huw Davies <huw@codeweavers.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This converts the AT91 pin control driver to register its
chained irq handler and irqchip using the helpers in the
gpiolib core.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix e26a9e00af 'ARM: Better
virt_to_page() handling' replaced __pv_phys_offset with
__pv_phys_pfn_offset. Also note that size of __pv_phys_offset
was quad but size of __pv_phys_pfn_offset is word. Instruction
that used to update __pv_phys_offset which address is in r6
had to update low word of __pv_phys_offset so it used #LOW_OFFSET
macro for store offset. Now when size of __pv_phys_pfn_offset is
word, no difference between little endian and big endian should
exist - i.e no offset should be used when __pv_phys_pfn_offset
is stored.
Note that for little endian image proposed change is noop,
since in little endian case #LOW_OFFSET is defined 0 anyway.
Reported-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The switcher should not depend on MAX_CLUSTER to determine ifit should
be activated or not. In a multiplatform kernel binary it is possible to
have dual-cluster and quad-cluster platforms configured in. In that case
MAX_CLUSTER which is a build time limit should be 4 and that shouldn't
prevent the switcher from working if the kernel is booted on a b.L
dual-cluster system.
In bL_switcher_halve_cpus() we already have a runtime validation check
to make sure we're dealing with only two clusters, so booting on a quad
cluster system will be caught and switcher activation aborted.
However, the b.L switcher must ensure the MCPM layer is initialized on
the booted hardware before doing anything. The mcpm_is_available()
function is added to that effect.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Abhilash Kesavan <kesavan.abhilash@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For vmcore generated by LPAE enabled kernel, user space
utility such as crash needs additional infomation to
parse.
So this patch add arch_crash_save_vmcoreinfo as what PAE enabled
i386 linux does.
Cc: <stable@vger.kernel.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Liu Hua <sdu.liu@huawei.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In big-endian systems, "%1" get the most significant part of the value, cause the instruction to get the wrong result.
When viewing ftrace record in big-endian ARM systems, we found that
the timestamp errors:
swapper-0 [001] 1325.970000: 0:120:R ==> [001] 16:120:R events/1
events/1-16 [001] 1325.970000: 16:120:S ==> [001] 0:120:R swapper
swapper-0 [000] 1325.1000000: 0:120:R + [000] 15:120:R events/0
swapper-0 [000] 1325.1000000: 0:120:R ==> [000] 15:120:R events/0
swapper-0 [000] 1326.030000: 0:120:R + [000] 1150:120:R sshd
swapper-0 [000] 1326.030000: 0:120:R ==> [000] 1150:120:R sshd
When viewed ftrace records, it will call the do_div(n, base) function, which achieved arch/arm/include/asm/div64.h in. When n = 10000000, base = 1000000, in do_div(n, base) will execute "umull %Q0, %R0, %1, %Q2".
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Cc: <stable@vger.kernel.org> # 2.6.20+
Signed-off-by: Alex Wu <wuquanming@huawei.com>
Signed-off-by: Xiangyu Lu <luxiangyu@huawei.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no good reason to create a filestream when a directory entry
is created. Delay it until the first allocation happens to simply
the code and reduce the amount of mru cache lookups we do.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
We only have very few of these around, and allocation isn't that
much of a hot path. Remove the slab cache to simplify the code,
and to not waste any resources for the usual case of not having
any inodes that use the filestream allocator.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
