Move the "select RENESAS_INTC_IRQPIN" from the two bockw-specific sections
to the one r8a7778-specific section, like is done for the other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
[horms+renesas@verge.net.au: Resolved conflict]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On r8a7791 the hardware boot mode bit MD21 indicates if hardware
debug mode is enabled or not. In case hardware debug mode is enabled
print a warning and refrain from booting secondary CPU cores.
Without this patch Koelsch with SW8-4 set to OFF will hang at SMP boot.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The MD pins are sampled at reset time, hence the read value will always be
the same, and we can avoid the overhead of ioremapping the register on
every read.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move non-PFC and non-GPIO devices off from r8a7790_pinmux_init()
and into r8a7790_add_standard_devices() which is the normal place
to keep regular devices in the legacy case.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There is no C board code left for the EMEV2 SoC, so
get rid of the emev2.h include file to save some lines.
While at it make functions static.
Signed-off-by: Magnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au: Resolved conflict]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Get rid of legacy EMEV2 SoC code including the legacy clock
framework implementation. The multiplatform implementation
together with DT board support shall be used instead.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Introduce shmobile_init_delay() that gets CPU specific
parameters from DT and sets up the early delay from
there. This allows us to both remove frequency information
from the C code and consolidate existing code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The correct maximum CPU frequency for r8a7791 is 1500 MHz
so update the r8a7791 SoC C code to reflect this.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The USB [EO]HCI HCD drivers provide USB host support for Renesas
R-Car Gen2 platforms. To increase hardware support enable the driver in the
shmobile_defconfig multiplatform configuration.
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Both r8a7790 and r8a7791 have multiple on-chip VSP1 devices, so
enable the VSP1 driver by default in the shmobile_defconfig.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Many mach-shmobile hardware platforms include support for more
than 1GiB of RAM. Enable HIGHMEM by default to allow use of
larger amounts of memory.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The renesas_usbhs driver provides USB gadget support for most Renesas
platforms. To increase hardware support enable the driver in the
shmobile_defconfig multiplatform configuration.
Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Koelsch board includes an at24-compatible EEPROM hooked up via I2C.
To increase hardware support enable the driver in the shmobile_defconfig
multiplatform configuration.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Many SoCs include I2C controller instances compatible with
the i2c-shmobile.c driver. To increase hardware support enable
the driver in the shmobile_defconfig multiplatform configuration.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Per bindings of fixed-clock, #clock-cells is a required property. Let's
add it for those fixed rate clocks.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.
address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
In case the bootloader has incorrectly configured the ALT mode of
MX6SL_PAD_ECSPI1_SS0 pad, we end up with the following probe error:
m25p80 spi0.0: found mr25h256, expected m25p32
m25p80 spi0.0: mr25h256 (32 Kbytes)
In order to avoid this issue, add an entry for MX6SL_PAD_ECSPI1_SS0 pad, so
that kernel configures the ECSPI chip select as GPIO functionality, which
results in correct SPI NOR probe.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The 'remote-endpoint' property should point back to ipu_di1_lvds1
rather than ipu_di0_lvds0.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Since commit (655b43c staging: imx-drm-core: Use OF graph to find
components and connections between encoder and crtcs), 'crtcs' becomes a
dead property. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
With the recent imx-drm device tree binding changes, we need to add IPU
DI ports and endpoints for adapting.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
GPIO7_12 switches the D+/D- USB lines on and off. When we use this as
VBUS regulator it means that USB device mode can never work as VBUS is
never turned on in Device mode.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Bit 6,7 are marked as reserved for the ethernet RGMII pins, so avoid
setting these bits.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Allows fror proper refcounting of the parent clocks
when enabling the clock output on CLK1/2 pads.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Richard Zhu <r65037@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Those two properties should have been set to zero, which
is the same as not specifying them.
Having address-cells set to 1 causes OF interrupt
mapping routines to add 1 to the interrupt-cells
property and as result fail because all calculations
are off by one.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fix bindings for STMPE touchscreen controller to match the documented
bindings and the actual bindings used by the driver.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
On m53evk there are two DRAM chip selects:
CS0 at 0x70000000
CS1 at 0xb0000000
Each bank has a 512MB DRAM, giving a total of 1GB of system DRAM.
Fix the memory layout to describe the hardware appropriately.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
On mx53qsb there are two DRAM chip selects:
CS0 at 0x70000000
CS1 at 0xb0000000
Each bank has a 512MB DRAM, giving a total of 1GB of system DRAM.
Fix the memory layout to describe the hardware appropriately.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
As defined by the common PCI bindings.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Some versions of gcc even warn about it:
mm/shmem.c: In function ‘shmem_file_aio_read’:
mm/shmem.c:1414: warning: ‘error’ may be used uninitialized in this function
If the loop is aborted during the first iteration by one of the two
first break statements, error will be uninitialized.
Introduced by commit 6e58e79db8 ("introduce copy_page_to_iter, kill
loop over iovec in generic_file_aio_read()").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On 32 bit, size_t is "unsigned int", not "unsigned long", causing the
following warning when comparing with PAGE_SIZE, which is always "unsigned
long":
fs/cifs/file.c: In function ‘cifs_readdata_to_iov’:
fs/cifs/file.c:2757: warning: comparison of distinct pointer types lacks a cast
Introduced by commit 7f25bba819 ("cifs_iovec_read: keep iov_iter
between the calls of cifs_readdata_to_iov()"), which changed the
signedness of "remaining" and the code from min_t() to min().
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull slab changes from Pekka Enberg:
"The biggest change is byte-sized freelist indices which reduces slab
freelist memory usage:
https://lkml.org/lkml/2013/12/2/64"
* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
mm: slab/slub: use page->list consistently instead of page->lru
mm/slab.c: cleanup outdated comments and unify variables naming
slab: fix wrongly used macro
slub: fix high order page allocation problem with __GFP_NOFAIL
slab: Make allocations with GFP_ZERO slightly more efficient
slab: make more slab management structure off the slab
slab: introduce byte sized index for the freelist of a slab
slab: restrict the number of objects in a slab
slab: introduce helper functions to get/set free object
slab: factor out calculate nr objects in cache_estimate
Where are some places where logic guaranties us that extent we are
searching exits, but this may not be true due to on-disk data
corruption. If such corruption happens we must prevent possible
null pointer dereferences.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
7000 device series have a fix for this hardware feature.
Stop disabling it, and get an improvement in Tx throughput.
This feature allows the scheduler to fetch more frames on
the fly while an A-MPDU is being built - which means that
we can get larger A-MPDU. This, of course, give an
improvement in the Tx throughput.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver can enable uAPSD and specify some of its related parameters.
This patch organizes this logic in a separate function.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
bail out from the suspend/resume callbacks if
d0i3 is used.
declare support for ANY wowlan trigger (i.e.
normal operation).
On resume, we shouldn't execute the d0i3 exit
flow (which might disconnect stations, etc.)
until mac80211 was resumed.
Add new flags to indicate we are in suspend,
and call the pending exit work on resume.
Since the resume flow can take some time, add
a new EXIT_WORK reference type to prevent going
back to d0i3 at this stage.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch enables Energy Based Scan (EBS) - intended to detect energy
on 5 GHz band channels. Passive scan on this band takes up to 2.64 sec
assuming 110mSec per-channel * 24 channels. EBS is designed to detect
energy on channels with intensive Wifi activity as well as those where
only beacons are transmitted. EBS completes sampling all channels within
shortest beacon frame transmission time. Total EBS duration is about 100
msec (typical beacon interval).
Detecting Wifi activity on 5 GHz band channels can significantly reduce
scan duration thus saving time and power. EBS failure reported by FW
disables EBS for current connection. It is re-enabled upon new
connection attempt on any WLAN interface.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Calling iwl_send_bt_init_conf for INIT firmware is not a
problem, and calling iwl_send_bt_prio_tbl from
iwl_send_bt_init_conf allows us to prepare for new API.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The BT Coex API underwent a minor backward compatible API
change.
We now need to set an invalid value in the override fields.
While at it, add kerneldoc comments on the fields in the
command.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is really not needed. This is a remainder from a C99
initialiser.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
