As far as I know, the CS5520 and CS5530 chipsets were only used with
32-bit x86 Geode processors, so I think their drivers are only needed
on this architecture, except for build testing purpose.
While we're here, simplify the dependencies for the CS5535 driver.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a small patch which uses ARRAY_SIZE macro
rather than a number to make code readability better.
Signed-off-by: Doug Wilson <doug.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking a system call return code for an error,
linux_sparc_syscall was sign-extending the lower 32-bit value and
comparing it to -ERESTART_RESTARTBLOCK. lseek can return valid return
codes whose lower 32-bits alone would indicate a failure (such as 4G-1).
Use the whole 64-bit value to check for errors. Only the 32-bit path
should sign extend the lower 32-bit value.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Acked-by: Bob Picco <bob.picco@oracle.com>
Acked-by: Allen Pais <allen.pais@oracle.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the APM X-Gene SoC AHCI SATA host controller
driver. It requires the corresponding APM X-Gene SoC PHY driver. This
initial version only supports Gen3 speed.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Tuan Phan <tphan@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds the DTS entries for the APM X-Gene SoC 15Gbps Multi-purpose
PHY driver. The PHY for SATA controller 2 and 3 are enabled by default.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Tuan Phan <tphan@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Eric W. Biederman says:
====================
netpoll: Cleanup received packet processing
This is the long-winded, careful, and polite version of removing the netpoll
receive packet processing.
First I untangle the code in small steps. Then I modify the code to not
force reception and dropping of packets when we are transmiting a packet
with netpoll. Finally I move all of the packet reception under
CONFIG_NETPOLL_TRAP and delete CONFIG_NETPOLL_TRAP.
If someone wants to do a stable backport of these patches, it would
require backporting the first 18 patches that handle the budget == 0 in
the networking drivers, and the first 6 of these patches.
If anyone wants to resurrect netpoll packet reception someday it should
just be a matter of reverting the last patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The netpoll packet receive code only becomes active if the netpoll
rx_skb_hook is implemented, and there is not a single implementation
of the netpoll rx_skb_hook in the kernel.
All of the out of tree implementations I have found all call
netpoll_poll which was removed from the kernel in 2011, so this
change should not add any additional breakage.
There are problems with the netpoll packet receive code. __netpoll_rx
does not call dev_kfree_skb_irq or dev_kfree_skb_any in hard irq
context. netpoll_neigh_reply leaks every skb it receives. Reception
of packets does not work successfully on stacked devices (aka bonding,
team, bridge, and vlans).
Given that the netpoll packet receive code is buggy, there are no
out of tree users that will be merged soon, and the code has
not been used for in tree for a decade let's just remove it.
Reverting this commit can server as a starting point for anyone
who wants to resurrect netpoll packet reception support.
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make rx_skb_hook, and rx in struct netpoll depend on
CONFIG_NETPOLL_TRAP Make rx_lock, rx_np, and neigh_tx in struct
netpoll_info depend on CONFIG_NETPOLL_TRAP
Make the functions netpoll_rx_on, netpoll_rx, and netpoll_receive_skb
no-ops when CONFIG_NETPOLL_TRAP is not set.
Only build netpoll_neigh_reply, checksum_udp service_neigh_queue,
pkt_is_ns, and __netpoll_rx when CONFIG_NETPOLL_TRAP is defined.
Add helper functions netpoll_trap_setup, netpoll_trap_setup_info,
netpoll_trap_cleanup, and netpoll_trap_cleanup_info that initialize
and cleanup the struct netpoll and struct netpoll_info receive
specific fields when CONFIG_NETPOLL_TRAP is enabled and do nothing
otherwise.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bond slave device neigh_tx handling into service_neigh_queue.
In connection with neigh_tx processing remove unnecessary tests of
a NULL netpoll_info. As the netpoll_poll_dev has already used
and thus verified the existince of the netpoll_info.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we no longer need to receive packets to safely drain the
network drivers receive queue move netpoll_trap and netpoll_set_trap
under CONFIG_NETPOLL_TRAP
Making netpoll_trap and netpoll_set_trap noop inline functions
when CONFIG_NETPOLL_TRAP is not set.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the strategy of netpoll from dropping all packets received
during netpoll_poll_dev to calling napi poll with a budget of 0
(to avoid processing drivers rx queue), and to ignore packets received
with netif_rx (those will safely be placed on the backlog queue).
All of the netpoll supporting drivers have been reviewed to ensure
either thay use netif_rx or that a budget of 0 is supported by their
napi poll routine and that a budget of 0 will not process the drivers
rx queues.
Not dropping packets makes NETPOLL_RX_DROP unnecesary so it is removed.
npinfo->rx_flags is removed as rx_flags with just the NETPOLL_RX_ENABLED
flag becomes just a redundant mirror of list_empty(&npinfo->rx_np).
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper netpoll_rx_processing that reports when netpoll has
receive side processing to perform.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is already a warning for this case in the normal netpoll path,
but put a copy here in case how netpoll calls the poll functions
causes a differenet result.
netpoll will shortly call the napi poll routine with a budget 0 to
avoid any rx packets being processed. As nothing does that today
we may encounter drivers that have problems so a netpoll specific
warning seems desirable.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In poll_napi loop through all of the napi handlers even when the
budget falls to 0 to ensure that we process all of the tx_queues, and
so that we continue to call into drivers when our initial budget is 0.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves the control logic to the top level in netpoll_poll_dev
instead of having it dispersed throughout netpoll_poll_dev,
poll_napi and poll_one_napi.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today netpoll depends on setting NETPOLL_RX_DROP before networking
drivers receive packets in interrupt context so that the packets can
be dropped. Move this setting into netpoll_poll_dev from
poll_one_napi so that if ndo_poll_controller happens to receive
packets we will drop the packets on the floor instead of letting the
packets bounce through the networking stack and potentially cause problems.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This member of the subdevice private data is just the subdevice 'index'. Use
that instead and remove the member.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename this private struct so it has namespace associated with the
driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename this private struct so it has namespace associated with the
driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This member of the private data is actually the number of subdevices. We
can get that information directly from the comedi_device. Do that instead
and remove the unnecessary member from the private data.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create an enum for the boards supported by this driver and pass that enum in
the pci_driver id_table as the driver_data.
Introduce a boardinfo struct to hold the board specific data for the boards
supported by this driver. Use the boardinfo when attaching to the driver
instead of using the pcidev->device and the switch.
Since the PCI device ids are now only used in the id_table, remove the
defines and open code the device ids.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor this function to make it clearer.
The channel does not need to be validated. The comedi core does that for us.
Exit early if the subdevice private data is invalid.
Exit early if the subdevice 'state' is not done or there is an error.
Factor out the code that actually reads the channel data to reduce the
indent level.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For aesthetics, rename the subdevice private data pointer from 'p' to
'spriv' and add a local variable for the comedi_subdevice pointer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This callback function for comedi_load_firmware() first validates that
the firmware data is the correct format then it writes the data to each
subdevice.
Split the two operations out as separate functions to clarify the code.
Tidy up the new functions.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the function to reduce the indent level.
For aesthetics, rename the subdevice private data pointer from 'p'
to 'spriv'.
Rename the lacal variable used for the channel->full_scale to 'fs'
to reduce the line lengths.
Remove the setting of range[8]. The min,max values are the same as
the ones used when the subdevice private data was allocated and
initialized.
Remove the poll_delay_min_max() that are the same as the default.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For aesthetics, rename the subdevice private data pointer from 'subdevpriv'
to 'spriv' and add a local variable for the comedi_subdevice pointer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For aesthetics, rename the subdevice private data pointer from 'p'
to 'spriv' and the variable used to check the errno from 'result'
to 'ret'.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Factor the code that allocates and initializes the subdevice private data
out of the (*attach) to reduce the indent level and make the code easier
to follow.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the helper function to allocate the subdevice private data. This
sets the s->private variable for us and allows the comedi core to
automatically kfree() the memory during the (*detach).
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For aesthetics, use a pointer to the comedi_subdevice instead of
accessing the dev->subdevices array directly.
Move the local variable for the subdevice private data so that
this function does not declare the variable twice.
Change the kzalloc for the subdevice private data to remove the
sizeof(struct foo).
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The use of KERN_INFO causes garbage characters to appear when
debugging is enabled.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
After commit a11a2bf4, "SUNRPC: Optimise away unnecessary data moves
in xdr_align_pages", Thu Aug 2 13:21:43 2012, READs larger than a
few hundred bytes via NFS/RDMA no longer work. This commit exposed
a long-standing bug in rpcrdma_inline_fixup().
I reproduce this with an rsize=4096 mount using the cthon04 basic
tests. Test 5 fails with an EIO error.
For my reproducer, kernel log shows:
NFS: server cheating in read reply: count 4096 > recvd 0
rpcrdma_inline_fixup() is zeroing the xdr_stream::page_len field,
and xdr_align_pages() is now returning that value to the READ XDR
decoder function.
That field is set up by xdr_inline_pages() by the READ XDR encoder
function. As far as I can tell, it is supposed to be left alone
after that, as it describes the dimensions of the reply xdr_stream,
not the contents of that stream.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=68391
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Security labels go with each directory entry, thus they are always
stored in the page cache, not in the head buffer. The length of the
reply that goes in head[0] should not have changed to support
NFSv4.2 labels.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
The COMEDI_CMD and COMEDI_CMDTEST ioctl functions both copy the chanlist
passed by the user from __user memory space to kernel memory space. They
then do some sanity checking of the chanlist with comedi_check_chanlist()
before the subdevice (*do_cmdtest) and (*do_cmd) operations are called.
Introduce a helper function to handle the memdup_user() and the sanity
checking.
Also, remove the unnecessary dev_dbg() when the memdup_user() or
comedi_check_chanlist() fail.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The COMEDI_CMD and COMEDI_CMDTEST ioctl functions both copy the
comedi_cmd passed by the user from __user memory space to kernel
memory space. They then do some basic sanity checking of the cmd
before the subdevice (*do_cmdtest) and (*do_cmd) operations are
called.
Introduce a helper function to handle the copy_from_user() and
do the basic sanity checking.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise non-empty orphan list will be triggered on umount.
This is just an application of commit da1daf by Dmitry Monakhov
to the same code in ext3.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
If the rpcbind server is unavailable, we still want the RPC client
to respect the timeout.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
When the server is unavailable due to a networking error, etc, we want
the RPC client to respect the timeout delays when attempting to reconnect.
Reported-by: Neil Brown <neilb@suse.de>
Fixes: 561ec16031 (SUNRPC: call_connect_status should recheck bind..)
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
If a file is sillyrenamed, then the generic vfs_unlink code will skip
emitting fsnotify events for it.
This patch has the sillyrename code do that instead.
In truth this is a little bit odd since we aren't actually removing the
dentry per-se, but renaming it. Still, this is probably the right thing
to do since it's what userland apps expect to see when an unlink()
occurs or some file is renamed on top of the dentry.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Tested-by: Anna Schumaker <Anna.Schumaker@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Now that nfs_rename uses the async infrastructure, we can remove this.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Tested-by: Anna Schumaker <Anna.Schumaker@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
There isn't much sense in maintaining two separate versions of rename
code. Convert nfs_rename to use the asynchronous rename infrastructure
that nfs_sillyrename uses, and emulate synchronous behavior by having
the task just wait on the reply.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Tested-by: Anna Schumaker <Anna.Schumaker@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
...and move the prototype for nfs_sillyrename to internal.h.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Tested-by: Anna Schumaker <Anna.Schumaker@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
The async rename code is currently "polluted" with some parts that are
really just for sillyrenames. Add a new "complete" operation vector to
the nfs_renamedata to separate out the stuff that just needs to be done
for a sillyrename.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Tested-by: Anna Schumaker <Anna.Schumaker@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Code cleanup by following i915 constant/variable names and ordering
Code cleanup by following directions from kernel doc: Codingstyle
Code cleanup by following directions from kernel doc: DRM
Signed-off-by: Arthur Borsboom <arthurborsboom@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Removed centralized exiting of function (goto statement), since it was
the only used in one single location with only a return statement.
Signed-off-by: Arthur Borsboom <arthurborsboom@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
