During initialization a number of RX skbs are allocated and mapped
for DMA.
Currently if pci_map_single() fails, it will result in passing to the
HW a wrong DMA address (to write to!).
This patch adds check for this condition and eventually causes the
driver not to initialize, avoiding at least dangerous DMAs.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the driver uses pci_iomap() but iounmap() is called in
the error path
Change to use pci_iounmap() instead.
Reported-by: Huqiu Liu <liuhq11@mails.tsinghua.edu.cn>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the contention window enable/disable HW flag is not
touched by the driver.
This patch explicitly set it to the correct value to make sure
contention window is enabled (AFAIK contention window must be
enabled in most (if not all) cases.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add device tree binding documentation for Texas Instrument's wl1251
wireless lan chip. For now only the SPI binding is documented.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add device tree support for the spi variant of wl1251.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for requesting the regulator powering
the vio pin.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the power GPIO handling from the board code into
the driver. This is a dependency for device tree support.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the wl1251 part of the wl12xx platform data structure into a new
structure specifically for wl1251. Change the platform data built-in
block and board files accordingly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now the ACPI container and ACPI PCI hotplug driver has been converted
as built-in modules, so reflect these changes in IA64 defconfig file.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
To: linux-kernel@vger.kernel.org
Fix the section mismatch warning by remove __init annotate for functions
ioc_iova_init(), ioc_init() and acpi_sba_ioc_add() because they may be called at runtime.
WARNING: vmlinux.o(.data+0x66ee0): Section mismatch in reference from the variable acpi_sba_ioc_handler to the function .init.text:acpi_sba_ioc_add()
The variable acpi_sba_ioc_handler references
the function __init acpi_sba_ioc_add()
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
As many Surface Pro I & II users have found out, the mwifiex_usb
doesn't support usb autosuspend, and it has caused some system
stability issues.
Bug 69661 - mwifiex_usb on MS Surface Pro 1 is unstable
Bug 60815 - Interface hangs in mwifiex_usb
Bug 64111 - mwifiex_usb USB8797 crash failed to get signal
information
USB autosuspend get triggered when Surface Pro's AC power is
removed or powertop enables power saving on USB8797 device.
Driver's suspend handler is called here, but resume handler
won't be called until the AC power is put back on or powertop
disables power saving for USB8797.
We need to refactor the suspend/resume handlers to support
usb autosuspend properly. For now let's just remove it.
Cc: <stable@vger.kernel.org> # 3.5+
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The stop_scan_complete function was used as an intermediate step before
doing the actual connection creation. Since we're using hci_request
there's no reason to have this extra function around, i.e. we can simply
put both HCI commands into the same request.
The single task that the intermediate function had, i.e. indicating
discovery as stopped is now taken care of by a new
HCI_LE_SCAN_INTERRUPTED flag which allows us to do the discovery state
update when the stop scan command completes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The discovery process has a timer for disabling scanning, however
scanning might be disabled through other means too like the auto-connect
process. We should therefore ensure that the timer is never active
after sending a HCI command to disable scanning.
There was some existing code in stop_scan_complete trying to avoid the
timer when a connect request interrupts a discovery procedure, but the
other way around was not covered. This patch covers both scenarios by
canceling the timer as soon as we get a successful command complete for
the disabling HCI command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Restructure the way we bring the various GPIOs out of reset. In particular:
1. we only need to setup the GPIOs as outputs once
2. there's no point in writing 0x40 to register 0x00 since that's the EEPROM
write protect and already it's configured as an input
3. Separate out the act of enabling the power supply and bringing the tuner
and demod out of reset. If you don't then the chip may not be properly
enabled (as the power supply is still ramping up when the chip comes
out of reset). This can result in probing failures.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
An attempt was made to read dvbs2_snr_tab[80],
though dvbs2_snr_tab has only 80 elements.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We are checking sizeof() the wrong variable!
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No need to check lock twice here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add m88rs2000_get_tune_settings, min delay of 2000 ms on symbol
rate more than 3000000 and delay of 3000ms less than this.
Adding min delay prevents crashing the frontend on continuous
transponder scans. Other dvb_frontend_tune_settings remain as default.
This makes very little time difference to good channel scans, but slows down
the set frontend where lock can never be achieved i.e. DVB-S2.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds Controls to set Horizontal and Vertical search range
for Motion Estimation block for Samsung MFC video Encoders.
Signed-off-by: Swami Nathan <swaminath.p@samsung.com>
Signed-off-by: Amit Grover <amit.grover@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adding V4L2 controls for horizontal and vertical search range in pixels
for motion estimation module in video encoder.
Signed-off-by: Swami Nathan <swaminath.p@samsung.com>
Signed-off-by: Amit Grover <amit.grover@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Aaron Brown says:
====================
This series contains updates to ixgbe and ixgbevf.
Don provides an update to change a hard coded timeout interval to
a system-wide timeout one, collects AUTOC register functions into
one place and fixes some firmware bit handling.
Emil resolves a tx handling error introduced in a recent commit and
adds check for CHECKSUM_PARTIAL to avoid an skb_is_gso check
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds check for CHECKSUM_PARTIAL to avoid the skb_is_gso check
in ixgbevf_tso(). It should reduce overhead for workloads that are not using
TSO or checksum offloads. It is the same as in ixgbe.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves an issue introduced by:
commit 7ad1a09351
ixgbevf: make the first tx_buffer a repository for most of the skb info
Incorrect check for the result of ixgbevf_tso() can lead to calling
ixgbevf_tx_csum() which can spawn 2 context descriptors and result in
performance degradation and/or corrupted packets.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will now honor the MNG FW veto bit in blocking link resets.
This patch will affect x520 and x540 systems.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code doesn't toggle the correct bit to reset the data pipeline
on Restart_AN assertion. This patch corrects that.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reading or writing to the AUTOC register on 82599 devices we need to
preform various operations that aren't needed for other MAC types. This
patch will collect all of that code into one place to minimize MAC checks
in common code paths.
While doing this I also clean up some cases where we weren't holding the
SW/FW semaphore during a read/modify/write of AUTOC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we were just always polling for a hard coded 80 ms and not
respecting the system-wide timeout interval. Since up until now all
devices have been tested with this 80ms value we continue to use this
value as a hard minimum.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
"err" is zero here so we don't need to check again.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Messages relative to kinect_read() are printing "res" which contains the
return value of a previous kinect_write().
Print the correct value in the messages.
Cc: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The error checking code relative to the invocations of kinect_read()
does not return the actual return code of the function just called, it
returns "res" which still contains the value of the last invocation of
a previous kinect_write().
Return the proper value, and while at it also report with -EREMOTEIO the
case of a partial transfer.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Upgrade to videobuf2 libraries.
No errors reported with "v4l2-compliance -s".
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
sleep_on and its variants are broken and going away soon. This changes
the omap vout driver to use wait_event_interruptible_timeout instead,
which fixes potential race where the dma is complete before we
schedule.
[hans.verkuil@cisco.com: replaced interruptible_sleep_on_timeout by
wait_event_interruptible_timeout in the commit msg, obvious typo]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
interruptible_sleep_on is racy and going away. This replaces
one use in the radio-cadet driver with a wait_event_interruptible
call. Special care was taken that accesses to the rdsin and rdsout
indices are always done with dev->lock held.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Closer inspection on exact transmitted format showed that
we needed to add 1 on vertical sync.
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
HS_IN/VS_IN was always set to positive.
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently only RGB444 input data is supported so set to zero.
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Removal of unnecessary parameters from s2255_fh.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Start acquisition return code was not being checked. Return error
if start acquisition fails.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver was allocating a kernel buffer each time it was sending a command.
It is better to allocate this buffer once at startup.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Device tree node name should reflect the kind of device rather than the
specific name of the device.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Equal signs should always be preceded and followed by a single space in
device tree files.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
USB1 and USB3 are routed to two external connectors, while USB2 is used
for the integrated webcam.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The USB controllers on Tegra124 are backwards-compatible with those
found on Tegra30.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
