Fixes all style warnings from scripts/checkpatch -f
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
module_usb_driver eliminates the boilerplate and makes the code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This applies to HDMI-map register 0x69.
So far we have been using HPA manual mode.
This way we had control of HPA which could be
set after EDID had been programmed.
Using a Mac Mini with mini-displayport to DVI-D converter as source
caused the adv7842 to lock up and fail to detect any further signals.
After experimenting with different configurations it was found that
using the HPA auto mode and in addition letting RX-termination
be controlled by HPA prevented this error from occuring.
I was not able to re-create this problem on the adv7604.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Clear any pending AVI checksum-errors.
To be able to display last received AVI.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Incorrect registers used for pixelclock read-out.
Same registers as for adv7604 which actually gave an almost
correct read-out, even they are not documented for adv7842.
Corrected deep-color pixel-clock correction.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the input signal is DVI-D and quantization range is RGB full range,
gain and offset must be adjusted to get the right range on the output.
Copied and adopted from adv7604.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I came across this while checking the kernel use of V4L2_CTRL_FLAG_DISABLED.
This flag should not be used with the control framework. Instead, just don't
add the control at all.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This define uses the deprecated interruptible_sleep_on_timeout
function. Since this define is unused anyway we just remove it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When used via spidev with more than one messages to tranfer via
SPI_IOC_MESSAGE the current implementation would return with
-EINVAL, since bits_per_word and speed_hz are set in all
transfer structs. And in the 2nd loop status will stay at
-EINVAL as its not overwritten again via fsl_spi_setup_transfer().
This patch changes this behavious by first checking if one of
the messages uses different settings. If this is the case
the function will return with -EINVAL. If not, the messages
are transferred correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the pointer-integer size mismatch warning below:
drivers/spi/spi-gpio.c: In function ‘spi_gpio_setup’:
drivers/spi/spi-gpio.c:252:8: warning: cast from pointer to integer of
different size [-Wpointer-to-int-cast]
cs = (unsigned int) spi->controller_data;
^
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
rspi_wait_for_interrupt() unconditionally enables interrupts, even when the
wait condition is already satisfied. This causes a high interrupt load (2
interrupts/byte for full-duplex Single SPI transfers, 1 interrupt/byte for
RSPI with TX Only mode, or QSPI in unidirectional Dual or Quad Transfer
mode).
Change this to return immediately when the wait condition is satisfied.
This dramatically reduces the interrupt load, especially in high-speed
Quad Transfer mode, and increases transfer speed, as no interrupts need to
be handled when there's space available in the output FIFO, or data
available in the input FIFO.
Benchmark results for QSPI on r8a7791 while reading 1 MiB from 30 MHz SPI
FLASH on the Koelsch development board:
Before:
Single SPI Dual SPI Quad SPI
Interrupts: 2096856 1048592 1048594
Mbps: 0.9 1.6 1.6
After:
Single SPI Dual SPI Quad SPI
Interrupts: 1048569 21295 8
Mbps: 0.7 10.8 12.9
I don't know why Single SPI slowed down a bit.
I've also verified functionality for RSPI-RZ on r7s72100, but don't have
benchmark results as there's no SPI FLASH connected to RSPI on the Genmai
development board. Unlike RSPI and QSPI, RSPI-RZ has separate interrupts
for RX and TX, which shows that Single SPI transfers now generate (mostly)
RX interrupts, as expected.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
When we enter RC6 and GFX Clocks are off, the voltage remains higher
than Vmin. When we try to set the freq to RPn, it might fail since the
Gfx clocks are down. So to fix this in Gfx idle, Bring the GFX clock up
and set the freq to RPn then move GFx down.
v2: remove vlv_update_rps_cur_delay function. Update commit message (Daniel)
v3: Fix the timeout during wait for gfx clock (Jesse)
v4: addressed comments on set freq and punit wait (Ville)
v5: use wait_for while waiting for GFX clk to be up. (Daniel)
update cur_delay before requesting min_delay. (Ville)
v6: use wait_for while waiting for punit. (Ville)
Signed-off-by: Deepak S <deepak.s@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we seek the guilty batch using request and hangcheck
score, this code is not needed anymore.
v2: Rebase. Passing dev_priv instead of getting it from last_ring
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With full ppgtt using acthd is not enough to find guilty
batch buffer. We get multiple false positives as acthd is
per vm.
Instead of scanning which vm was running on a ring,
to find corressponding context, use a different, simpler,
strategy of finding batches that caused gpu hang:
If hangcheck has declared ring to be hung, find first non complete
request on that ring and claim it was guilty.
v2: Rebase
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73652
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both Bspec and the W/A database state that WaDisablePSDDualDispatchEnable
is only needed for IVB GT1.
The only real confusion here is that the the W/A database also says to
write to the GT2 only register as well, which is strange if the W/A is
only for GT1.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IVB GT2 has two registers for these things, and both must be written.
To add a bit more confusion both Bspec and the W/A database state that
WaDisablePSDDualDispatchEnable is only needed for IVB GT1, but the W/A
database also says to write even the second GT2 only register. So I
don't really know what the right thing here is.
Note that Bspec disagrees with the w/a database here, but Ville
confirmed (by asking Chris) that on gt1 the 2nd reg doesn't exist.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add note as requested by Rodrigo.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add the reg-io-width property to describe the width of the memory
accesses.
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The OpenFirmware probe can be merged into the standard platform
probe to leverage common code.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Simplify probe and remove functions by converting most of the resources
to use devm_* APIs.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
usbtv-video.c needs module.h. So move the module.h include from usbtv-core.c to usbtv.h,
that way both core.c and video.c have it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use netdev_* where applicable.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Round off image width to nearest 8 (GTF_CELL_GRAN)
A source sending a GTF (Generalized Timing Formula) format have no means of
signalling image width. The assumed aspect ratio may result in an odd image
width but according to the standard image width should be in multiple of 8.
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
cppcheck reported memory leak in device_authorizatio()
within hdpvr-core.c.
When the debug option is specified and the code jump to
"unlock:" label, print_buf was not freed.
Confirm the module succesfully compiled without error.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add USB ID [2040:f900] for Hauppauge WinTV-MiniStick 2.
Device is build upon IT9135 chipset.
Tested-by: Stefan Becker <schtefan@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix the following build error:
drivers/media/usb/dvb-usb-v2/
mxl111sf-tuner.h:72:9: error: expected ‘;’, ‘,’ or ‘)’ before ‘struct’
struct mxl111sf_tuner_config *cfg)
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
mxl111sf_read_reg takes an address of a variable to write to as an argument.
drivers/media/usb/dvb-usb-v2/mxl111sf-gpio.c:mxl111sf_config_pin_mux_modes
passes several uninitialized stack variables to this routine, expecting
them to be filled in. In the event that something unexpected happens when
reading from the chip, we end up doing a pr_debug of the value passed in,
revealing whatever garbage happened to be on the stack.
Change the pr_debug to match what happens in the 'success' case, where we
assign buf[1] to *data.
Spotted with Coverity (Bugs 731910 through 731917)
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Don't use '&state->priv->i2c->dev' reference to device because
state is still 'NULL'. Use '&i2c->dev' instead.
This bug has been reported by scan.coverity.com
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: vger@stable.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
At this point of the execution in the function cx24117_attach()
demod cannot be '0'. In that case the function returns earlier
with an error value ('NULL'). Remove the if statement.
This error has been reported by scan.coverity.com
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the ability of allocating a CANFD frame data structure in the
skb data area.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is in the spirit of commit 2485602f1a (can: add explicit
copyrights to can headers). It seems I have missed can.h back then.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
I am no longer available at the kernellabs.com or m1k.net email
addresses. Update each instance of my email to my linuxtv.org
account.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds a test preventing streamon() if there is no buffer
ready.
Without this patch, a user could call streamon() before
preparing any buffer. This leads to a situation where if he calls
close() before calling streamoff() the device is kept streaming.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This reverts commit a242f42610.
That commit actually caused deadlocks, rather then fixing them.
If ext_lock is set to NULL (otherwise videobuf_queue_lock doesn't do
anything), then you get this deadlock:
The driver's mmap function calls videobuf_mmap_mapper which calls
videobuf_queue_lock on q. videobuf_mmap_mapper calls __videobuf_mmap_mapper,
__videobuf_mmap_mapper calls videobuf_vm_open and videobuf_vm_open
calls videobuf_queue_lock on q (introduced by above patch): deadlocked.
This affects drivers using dma-contig and dma-vmalloc. Only dma-sg is
not affected since it doesn't call videobuf_vm_open from __videobuf_mmap_mapper.
Most drivers these days have a non-NULL ext_lock. Those that still use
NULL there are all fairly obscure drivers, which is why this hasn't been
seen earlier.
Since everything worked perfectly fine for many years I prefer to just
revert this patch rather than trying to fix it. videobuf is quite fragile
and I rather not touch it too much. Work is (slowly) progressing to move
everything over to vb2 or at the very least use non-NULL ext_lock in
videobuf.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v3.11 and up
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Reported-by: Pete Eberlein <pete@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is usb_get_dev() in go7007_loader_probe(),
but there is no usb_put_dev() anywhere.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is required so that we give up the last reference to the device.
Remove the kfree() because the put_device() call will actually call
release_sub_device which in turn kfrees the device.
Signed-off-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Enclose the runtime PM helpers in #ifdef CONFIG_PM_RUNTIME/#endif
to avoid following compile warning when CONFIG_PM_RUNTIME is disabled:
CC drivers/media/platform/exynos4-is/fimc-lite.o
drivers/media/platform/exynos4-is/fimc-lite.c:1591:12: warning: ‘fimc_lite_runtime_resume’ defined but not used [-Wunused-function]
drivers/media/platform/exynos4-is/fimc-lite.c:1599:12: warning: ‘fimc_lite_runtime_suspend’ defined but not used [-Wunused-function]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Enclose the runtime PM helpers in #ifdef CONFIG_PM_RUNTIME/#endif
to avoid following compile warning when CONFIG_PM_RUNTIME is disabled:
CC drivers/media/platform/exynos4-is/fimc-core.o
drivers/media/platform/exynos4-is/fimc-core.c:1040:12: warning: ‘fimc_runtime_resume’ defined but not used
drivers/media/platform/exynos4-is/fimc-core.c:1057:12: warning: ‘fimc_runtime_suspend’ defined but not used
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ensure clk_disable() is called on error paths only when clk_enable()
was previously called.
This fixes following build warning:
.../media-git/drivers/media/platform/exynos4-is/fimc-lite.c: In function 'fimc_lite_probe':
.../media-git/drivers/media/platform/exynos4-is/fimc-lite.c:1583:1: warning: label 'err_sd' defined but not used [-Wunused-label]
Reported-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
NV12 format entries in the sjpeg_formats array had wrong
colplanes, depth and v_align values.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Using variable length array in s5k5baf_write_arr_seq caused
an implicit assumption that i2c sequences should be short.
The patch rewrites the function so it can handle sequences
of any length and does not use variable length array.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move the kmem_cache_free() calls down a couple lines.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Toshiba Satellite L40 with AD1986A codec requires the EAPD of NID 0x1b
to be constantly on, otherwise the output doesn't work.
Unlike most of other AD1986A machines, EAPD is correctly implemented
in HD-audio manner (that is, bit set = amp on), so we need to clear
the inv_eapd flag in the fixup, too.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=67481
Cc: <stable@vger.kernel.org> [v3.11+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
list_for_each_entry() handles empty lists just fine, so there's no need to
check whether the list is empty first.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
We deprecated pci_enable_msi() in 302a2523c2 ("PCI/MSI: Add
pci_enable_msi_range() and pci_enable_msix_range()").
But we changed our minds after noticing that:
- pci_enable_msi() doesn't have confusing return values like
pci_enable_msi_block() and pci_enable_msix() did, and
- pci_enable_msi() has a hundred or so callers that we don't want to
change.
This adds back the pci_enable_msi() documentation.
[bhelgaas: changelog]
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Coverity reported that I forgot to clean up some allocated memory on the
error path in populate_msi_sysfs(), so this patch fixes that.
Thanks to Dave Jones for pointing out where the error was, I obviously
can't read code this morning...
Found by Coverity (CID 1163317).
Fixes: 1c51b50c29 ("PCI/MSI: Export MSI mode using attributes, not kobjects")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Dave Jones <davej@redhat.com>
