Force power saving off while monitor interface is present.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Port multicast address filtering from wl1271 driver.
It sets up the hardware multicast address filter in configure_filter() with
addresses supplied through prepare_multicast().
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable hardware encryption (DF_ENCRYPTION_DISABLE) and decryption
(DF_SNIFF_MODE_ENABLE) via wl1251_acx_feature_cfg while monitor interface is
present.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split up data path initialisation into RX and TX data path initialisation
functions. This change is required for channel switching in monitor mode.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update hardware ARP filter configuration on BSS_CHANGED_ARP_FILTER
notification from mac80211.
Ported from wl1271 driver.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Port of the power save entry retry code from wl1251 driver version included
in the Maemo Fremantle kernel.
This tries to enable power save mode up to 3 times before failing.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With a dissasociated card I often encoutered very long scan delays.
My guess is that it has something to do with the cards DTIM handling and
another firmware bug mentioned in the TI WLAN driver, which is described as
the card may never end scanning if the channel is overloaded because it
can't send probe requests. I think the firmware somehow also tries to
receive DTIM messages when the BSSID is not set. Therefore most of the time
it waits for DTIM messages and can't do scanning work.
Anyway we can workaround this misbehaviour by setting the HIGH_PRIORITY
bit for scans in disassociated state.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some DMA cores might add additional restrictions on which in memory audio
formats can be supported by the compound sound card. If the PCM component
specifies a set of formats it supports (by setting the formats field to non 0)
take these into account when calculating the format set for the compound sound
card.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
These sentences are not proper English due to the typos. I had initially caught
one of them while trying to understand the regmap feature, and then I just ran
the vim spell checker, and went through all the items that would need to be
fixed for this header file.
Signed-off-by: Laszlo Papp <lpapp@kde.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no need to force selection of TI EDMA DMA engine
driver when DaVinci SPI driver is selected. The driver
builds just fine even with CONFIG_TI_EDMA disabled.
Forcing this selection causes warnings of the sort:
warning: (ARCH_KEYSTONE && SPI_DAVINCI) selects TI_EDMA which has unmet direct dependencies (DMADEVICES && (ARCH_DAVINCI || ARCH_OMAP || ARCH_KEYSTONE))
This reverts commit b5f1433059.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit e13ac47bec (spi: Use stable dev_name for ACPI enumerated SPI
slaves) changed the SPI device naming to be based on ACPI device name
instead of carrying bus number and chip select for devices enumerated
from ACPI namespace.
In case of a buggy BIOS that lists multiple SPI devices sharing the same
chip select (even though they should use different) the current code fails
to detect that and allows the devices to be added to the bus.
Fix this by walking through the bus and comparing spi->chip_select instead
of device name. This should work regardless what the device name will be in
future.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
single_open requires a function with signature
'int (*)(struct seq_file *, void *)'. This patch fixes the warning by
fixing the wrong return type of fsl_ssi_stats_show.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no list of compatibles that are supported. This patch adds a
list of compatibles to the documentation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Enable use of DT for DMM/Tiler.
Originally worked on by Andy Gross <andygro@gmail.com>
Cc: Andy Gross <andygro@gmail.com>
Cc: DRI Development <dri-devel@lists.freedesktop.org>
Signed-off-by: Archit Taneja <archit@ti.com>
[tomi.valkeinen@ti.com: use of_match_ptr()]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a utility function to get the number of channels supported by
the device, and update the places in the code that need this data.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
[replace another occurrence in libertas, fix kernel-doc, fix bugs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current dev_unload order uninits the irqs too early.
In the current sequence, it's possible that a crtc queues work(apply_worker)
to display a buffer, which registers to omap_crtc_apply_irq to notfiy the
completion of the configuration we applied.
Calling drm_vblank_cleanup and omap_drm_irq_uninstall here causes the crtc's
apply handler to never get called, which results in an incorrect state of the
apply_irq.registered parameter.
This condition occurs where there is no mode set via omapdrm, and dev_lastclose
tries to set a default fb mode via drm_fb_helper_restore_fbdev_mode. The apply
work scheduled by restore_fbdev_mode is very close in time to the disabling of
the irq handler, and hence leads to a race condition. We move the irq cleanup
at the end of the unload sequence to prevent this.
Also, the call to flush_workqueue is removed since it's called internally by
destroy_workqueue.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, an encoder is disabled only when an apply work is queued for the
corresponding crtc. This works fine for the paths where userspace explicitly
disables crtc, this results in disabling the omapdss device in the crtc's
pre_apply function.
However, when the omapdrm module is removed, there is no work queued to ensure
that the encoder is disabled. This can result in an enabled omapdss device when
removing omapdrm. omapdss is left in an inconsistent state, and that prevents us
from using that omapdss device being used again.
Disable enabled encoders in omap_encoder_destroy, we could consider a better
place for doing this later.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At omapdrm probe, we install manager ops and connect omapdss devices. This
needs to be undone when omapdrm module is removed so that omapdss is in a
clean state. This ensures that we can re-insert omapdrm module, or some other
module which uses omapdss(like omapfb/omap_vout).
Currently, omapdrm's remove neither uninstalls manager ops, or disconnects
omapdss devices. We make sure that this is done in pdev_remove.
omapdrm establishes connections for omap_dss_device devices when probed. It
should also be responsible to disconnect the devices. Keeping the devices
connected can prevent the panel driver modules from unloading, it also causes
issues when we try to remove or re-insert omapdrm module.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With the omapdss device model changes. omapdrm is required to call dssdriver's
connect() op to register a panel. This is currently done in omap_modeset_init()
A call to connect() can fail if the omapdss panels or the encoders(HDMI/DPI)
they connect to have some resource(like regulators, I2C adapter) missing. If
this happens, the correct approach is to defer omapdrm's probe.
omapdrm currently ignores those panels which return a non zero value when
connected. This could result in omapdrm ignoring all panels on an omap board.
The right approach would be for omapdrm to request for probe deferral when a
panel's connect op returns -EPROBE_DEFER.
In order to do this, we need to call connect() much earlier during omapdrm's
probe to prevent too many things are already done by then. We now connect the
panels during pdev_probe(), before anything else is initialized, so that we
don't need to undo too many things if a defer was requested.
Now when we enter omap_modeset_init(), we have a set of panels that have been
connected. We now proceed with registering only those panels that are already
connected.
A special case has to be considered when no panels are available to connect when
omapdrm probes. In this case too, we defer probe and expect that a panel will be
available to connect the next time.
Checking whether the panel has a driver or whether it has get_timing/read_edid
ops in omap_modeset_init() are redundant with the new display model. These can
be removed since a dssdev device will always have a driver associated with it,
and all dssdev drivers have a get_timings op.
This will mainly fix cases when omapdrm is built-in the kernel, since that's
generally where resources like regulators or I2C are unavailable because of
probe order dependencies.
In particular this fixes boot with omapdrm built-in on an omap4 panda ES board.
The regulators used by HDMI(provided by I2C based TWL regulators) aren't
initialized because I2C isn't initialized, I2C isn't initialized as it's pins
are not configured because pinctrl is yet to probe.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdrm (un)registers irqs inside an irq handler. The problem is that
the (un)register function uses dispc_runtime_get/put() to enable the
clocks, and those functions are not irq safe by default.
This was kind of fixed in 48664b21ae
(OMAPDSS: DISPC: set irq_safe for runtime PM), which makes dispc's
runtime calls irq-safe.
However, using pm_runtime_irq_safe in dispc makes the parent of dispc,
dss, always enabled, effectively preventing PM for the whole DSS module.
This patch makes omapdrm behave better by adding new irq (un)register
functions that do not use dispc_runtime_get/put, and using those
functions in interrupt context. Thus we can make dispc again
non-irq-safe, allowing proper PM.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Rob Clark <robdclark@gmail.com>
Support to get sram pool from generic device tree binding. The
existing way of get sram poll, directly call sram_get_gpool(), still
work here.
Signed-off-by: Nenghua Cao <nhcao@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
"index" needs to be signed for the error handling to work. I deleted a
little bit of obsolete cruft related to "index" and "start_index" as
well.
Fixes: 360eb3c568 ('iommu/vt-d: use dedicated bitmap to track remapping entry allocation status')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
add pin groups for USP0 only holding one of TX and RX frame sync. this
patch matches with the change in drivers/pinctrl/sirf.
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Barry Song <Barry.Song@csr.com>
this patch adds lost usp1_uart_nostreamctrl pin group for atlas6, which
matches with the change in drivers/pinctrl/sirf/pinctrl-atlas6.c.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
This patch adds missing some description of sysfs entries in
- Documentation/ABI/testing/sysfs-fs-f2fs
- Documentation/filesystems/f2fs.txt.
And it adds a maintained document entry of F2FS in MAINTAINERS.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds lost minigpsrtc device node for prima2 and atlas6,
which is behind rtc-iobg and whose offset is 2000.
Signed-off-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
prima2 and atlas6 uses cpufreq_cpu0, here we put related clock, operation
points in dtsi.
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
some nodes missed bus_width, clocks and status properties, here we fix them
in prima2 and atlas6 dtsi.
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Enhance intel_iommu_init() to free all resources if failed to
initialize DMAR hardware.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Clean up most sparse warnings in Intel DMA and interrupt remapping
drivers.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
If dmar_table_init() fails to detect DMAR table on the first call,
it will return wrong result on following calls because it always
sets dmar_table_initialized no matter if succeeds or fails to
detect DMAR table.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
