The e500 SPE floating-point emulation code has several problems in how
it handles conversions to integer and fixed-point fractional types.
There are the following 20 relevant instructions. These can convert
to signed or unsigned 32-bit integers, either rounding towards zero
(as correct for C casts from floating-point to integer) or according
to the current rounding mode, or to signed or unsigned 32-bit
fixed-point values (values in the range [-1, 1) or [0, 1)). For
conversion from double precision there are also instructions to
convert to 64-bit integers, rounding towards zero, although as far as
I know those instructions are completely theoretical (they are only
defined for implementations that support both SPE and classic 64-bit,
and I'm not aware of any such hardware even though the architecture
definition permits that combination).
#define EFSCTUI 0x2d4
#define EFSCTSI 0x2d5
#define EFSCTUF 0x2d6
#define EFSCTSF 0x2d7
#define EFSCTUIZ 0x2d8
#define EFSCTSIZ 0x2da
#define EVFSCTUI 0x294
#define EVFSCTSI 0x295
#define EVFSCTUF 0x296
#define EVFSCTSF 0x297
#define EVFSCTUIZ 0x298
#define EVFSCTSIZ 0x29a
#define EFDCTUIDZ 0x2ea
#define EFDCTSIDZ 0x2eb
#define EFDCTUI 0x2f4
#define EFDCTSI 0x2f5
#define EFDCTUF 0x2f6
#define EFDCTSF 0x2f7
#define EFDCTUIZ 0x2f8
#define EFDCTSIZ 0x2fa
The emulation code, for the instructions that come in variants
rounding either towards zero or according to the current rounding
direction, uses "if (func & 0x4)" as a condition for using _FP_ROUND
(otherwise _FP_ROUND_ZERO is used). The condition is correct, but the
code it controls isn't. Whether _FP_ROUND or _FP_ROUND_ZERO is used
makes no difference, as the effect of those soft-fp macros is to round
an intermediate floating-point result using the low three bits (the
last one sticky) of the working format. As these operations are
dealing with a freshly unpacked floating-point input, those low bits
are zero and no rounding occurs. The emulation code then uses the
FP_TO_INT_* macros for the actual integer conversion, with the effect
of always rounding towards zero; for rounding according to the current
rounding direction, it should be using FP_TO_INT_ROUND_*.
The instructions in question have semantics defined (in the Power ISA
documents) for out-of-range values and NaNs: out-of-range values
saturate and NaNs are converted to zero. The emulation does nothing
to follow those semantics for NaNs (the soft-fp handling is to treat
them as infinities), and messes up the saturation semantics. For
single-precision conversion to integers, (((func & 0x3) != 0) || SB_s)
is the condition used for doing a signed conversion. The first part
is correct, but the second isn't: negative numbers should result in
saturation to 0 when converted to unsigned. Double-precision
conversion to 64-bit integers correctly uses ((func & 0x1) == 0).
Double-precision conversion to 32-bit integers uses (((func & 0x3) !=
0) || DB_s), with correct first part and incorrect second part. And
vector float conversion to integers uses (((func & 0x3) != 0) ||
SB0_s) (and similar for the other vector element), where the sign bit
check is again wrong.
The incorrect handling of negative numbers converted to unsigned was
introduced in commit afc0a07d4a. The
rationale given there was a C testcase with cast from float to
unsigned int. Conversion of out-of-range floating-point numbers to
integer types in C is undefined behavior in the base standard, defined
in Annex F to produce an unspecified value. That is, the C testcase
used to justify that patch is incorrect - there is no ISO C
requirement for a particular value resulting from this conversion -
and in any case, the correct semantics for such emulation are the
semantics for the instruction (unsigned saturation, which is what it
does in hardware when the emulation is disabled).
The conversion to fixed-point values has its own problems. That code
doesn't try to do a full emulation; it relies on the trap handler only
being called for arguments that are infinities, NaNs, subnormal or out
of range. That's fine, but the logic ((vb.wp[1] >> 23) == 0xff &&
((vb.wp[1] & 0x7fffff) > 0)) for NaN detection won't detect negative
NaNs as being NaNs (the same applies for the double-precision case),
and subnormals are mapped to 0 rather than respecting the rounding
mode; the code should also explicitly raise the "invalid" exception.
The code for vectors works by executing the scalar float instruction
with the trapping disabled, meaning at least subnormals won't be
handled correctly.
As well as all those problems in the main emulation code, the rounding
handler - used to emulate rounding upward and downward when not
supported in hardware and when no higher priority exception occurred -
has its own problems.
* It gets called in some cases even for the instructions rounding to
zero, and then acts according to the current rounding mode when it
should just leave alone the truncated result provided by hardware.
* It presumes that the result is a single-precision, double-precision
or single-precision vector as appropriate for the instruction type,
determines the sign of the result accordingly, and then adjusts the
result based on that sign and the rounding mode.
- In the single-precision cases at least the sign determination for
an integer result is the same as for a floating-point result; in
the double-precision case, converted to 32-bit integer or fixed
point, the sign of a double-precision value is in the high part of
the register but it's the low part of the register that has the
result of the conversion.
- If the result is unsigned fixed-point, its sign may be wrongly
determined as negative (does not actually cause problems, because
inexact unsigned fixed-point results with the high bit set can
only appear when converting from double, in which case the sign
determination is instead wrongly using the high part of the
register).
- If the sign of the result is correctly determined as negative, any
adjustment required to change the truncated result to one correct
for the rounding mode should be in the opposite direction for
two's-complement integers as for sign-magnitude floating-point
values.
- And if the integer result is zero, the correct sign can only be
determined by examining the original operand, and not at all (as
far as I can tell) if the operand and result are the same
register.
This patch fixes all these problems (as far as possible, given the
inability to determine the correct sign in the rounding handler when
the truncated result is 0, the conversion is to a signed type and the
truncated result has overwritten the original operand). Conversion to
fixed-point now uses full emulation, and does not use "asm" in the
vector case; the semantics are exactly those of converting to integer
according to the current rounding direction, once the exponent has
been adjusted, so the code makes such an adjustment then uses the
FP_TO_INT_ROUND macros.
The testcase I used for verifying that the instructions (other than
the theoretical conversions to 64-bit integers) produce the correct
results is at <http://lkml.org/lkml/2013/10/8/708>.
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
On overflow, the math-emu macro _FP_TO_INT_ROUND tries to saturate its
result (subject to the value of rsigned specifying the desired
overflow semantics). However, if the rounding step has the effect of
increasing the exponent so as to cause overflow (if the rounded result
is 1 larger than the largest positive value with the given number of
bits, allowing for signedness), the overflow does not get detected,
meaning that for unsigned results 0 is produced instead of the maximum
unsigned integer with the give number of bits, without an exception
being raised for overflow, and that for signed results the minimum
(negative) value is produced instead of the maximum (positive) value,
again without an exception. This patch makes the code check for
rounding increasing the exponent and adjusts the exponent value as
needed for the overflow check.
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The math-emu macros _FP_TO_INT and _FP_TO_INT_ROUND are supposed to
saturate their results for out-of-range arguments, except in the case
rsigned == 2 (when instead the low bits of the result are taken).
However, in the case rsigned == 0 (converting to unsigned integers),
they mistakenly produce 0 for positive results and the maximum
unsigned integer for negative results, the opposite of correct
unsigned saturation. This patch fixes the logic.
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The e500 SPE floating-point emulation code for the rounding modes
rounding to positive or negative infinity (which may not be
implemented in hardware) tries to avoid emulating rounding if the
result was inexact. However, it tests inexactness using the sticky
bit with the cumulative result of previous operations, rather than
with the non-sticky bits relating to the operation that generated the
interrupt. Furthermore, when a vector operation generates the
interrupt, it's possible that only one of the low and high parts is
inexact, and so only that part should have rounding emulated. This
results in incorrect rounding of exact results in these modes when the
sticky bit is set from a previous operation.
(I'm not sure why the rounding interrupts are generated at all when
the result is exact, but empirically the hardware does generate them.)
This patch checks for inexactness using the correct bits of SPEFSCR,
and ensures that rounding only occurs when the relevant part of the
result was actually inexact.
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The e500 SPE floating-point emulation code clears existing exceptions
(__FPU_FPSCR &= ~FP_EX_MASK;) before ORing in the exceptions from the
emulated operation. However, these exception bits are the "sticky",
cumulative exception bits, and should only be cleared by the user
program setting SPEFSCR, not implicitly by any floating-point
instruction (whether executed purely by the hardware or emulated).
The spurious clearing of these bits shows up as missing exceptions in
glibc testing.
Fixing this, however, is not as simple as just not clearing the bits,
because while the bits may be from previous floating-point operations
(in which case they should not be cleared), the processor can also set
the sticky bits itself before the interrupt for an exception occurs,
and this can happen in cases when IEEE 754 semantics are that the
sticky bit should not be set. Specifically, the "invalid" sticky bit
is set in various cases with non-finite operands, where IEEE 754
semantics do not involve raising such an exception, and the
"underflow" sticky bit is set in cases of exact underflow, whereas
IEEE 754 semantics are that this flag is set only for inexact
underflow. Thus, for correct emulation the kernel needs to know the
setting of these two sticky bits before the instruction being
emulated.
When a floating-point operation raises an exception, the kernel can
note the state of the sticky bits immediately afterwards. Some
<fenv.h> functions that affect the state of these bits, such as
fesetenv and feholdexcept, need to use prctl with PR_GET_FPEXC and
PR_SET_FPEXC anyway, and so it is natural to record the state of those
bits during that call into the kernel and so avoid any need for a
separate call into the kernel to inform it of a change to those bits.
Thus, the interface I chose to use (in this patch and the glibc port)
is that one of those prctl calls must be made after any userspace
change to those sticky bits, other than through a floating-point
operation that traps into the kernel anyway. feclearexcept and
fesetexceptflag duly make those calls, which would not be required
were it not for this issue.
The previous EGLIBC port, and the uClibc code copied from it, is
fundamentally broken as regards any use of prctl for floating-point
exceptions because it didn't use the PR_FP_EXC_SW_ENABLE bit in its
prctl calls (and did various worse things, such as passing a pointer
when prctl expected an integer). If you avoid anything where prctl is
used, the clearing of sticky bits still means it will never give
anything approximating correct exception semantics with existing
kernels. I don't believe the patch makes things any worse for
existing code that doesn't try to inform the kernel of changes to
sticky bits - such code may get incorrect exceptions in some cases,
but it would have done so anyway in other cases.
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The variable 'dev' is initialized but never used
otherwise, so remove the unused variable.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Genuine FTDI chips support only CS7/8. A previous fix in commit
8704211f65 ("USB: ftdi_sio: fixed handling of unsupported CSIZE
setting") enforced this limitation and reported it back to userspace.
However, certain types of smartcard readers depend on specific
driver behaviour that requests 0 data bits (not 5) to change into a
different operating mode if CS5 has been set.
This patch reenables this behaviour for all FTDI devices.
Tagged to be added to stable, because it affects a lot of users of
embedded systems which rely on these readers to work properly.
Cc: stable <stable@vger.kernel.org>
Reported-by: Heinrich Siebmanns <H.Siebmanns@t-online.de>
Tested-by: Heinrich Siebmanns <H.Siebmanns@t-online.de>
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to imx28 needs ARM swp instruction for writing, we set
CI_HDRC_IMX28_WRITE_FIX for imx28.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have already renamed the file name, change doc name at this
patch.
Cc: devicetree@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes the controller register map ci_regs_nolpm and ci_regs_lpm as
"const". Further, as all offset fit into a single byte, the type is changed
from uintptr_t to u8.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this patch a seperate chunk of memory is allocated for the regmap
array. As the regmap is always used it makes no sense to allocate a seperate
memory block for it, this patch moves the regmap array directly into the struct
hw_bank.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_USB_DEBUG is going away, and all of the other USB drivers no
longer rely on "debug" module parameters for debugging lines, so move
the pcwd_usb driver to use the dynamic debug infrastructure to be more
in line with the rest of the kernel.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
According to CY7C67300 specification HPI read and write cycle duration
Tcyc must be at least 6T long, where T is 1/48MHz, which is 125ns.
Without this delay fast host processor cannot write to chip registers.
Add proper ndelay to hpi_{read,write}_reg.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LRAT (Logical to Real Address Translation) present in MMU v2 provides hardware
translation from a logical page number (LPN) to a real page number (RPN) when
tlbwe is executed by a guest or when a page table translation occurs from a
guest virtual address.
Add LRAT error exception handler to Booke3E 64-bit kernel and the basic KVM
handler to avoid build breakage. This is a prerequisite for KVM LRAT support
that will follow.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Jon Maloy says:
====================
tipc: link setup and failover improvements
This series consists of four unrelated commits with different purposes.
- Commit #1 is purely cosmetic and pedagogic, hopefully making the
failover/tunneling logics slightly easier to understand.
- Commit #2 fixes a bug that has always been in the code, but was not
discovered until very recently.
- Commit #3 fixes a non-fatal race issue in the neighbour discovery
code.
- Commit #4 removes an unnecessary indirection step during link
startup.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link is created we delay the start event by launching it
to be executed later in a tasklet. As we hold all the
necessary locks at the moment of creation, and there is no risk
of deadlock or contention, this delay serves no purpose in the
current code.
We remove this obsolete indirection step, and the associated function
link_start(). At the same time, we rename the function tipc_link_stop()
to the more appropriate tipc_link_purge_queues().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, only 'bearer_lock' is used to protect struct link_req in
the function disc_timeout(). This is unsafe, since the member fields
'num_nodes' and 'timer_intv' might be accessed by below three different
threads simultaneously, none of them grabbing bearer_lock in the
critical region:
link_activate()
tipc_bearer_add_dest()
tipc_disc_add_dest()
req->num_nodes++;
tipc_link_reset()
tipc_bearer_remove_dest()
tipc_disc_remove_dest()
req->num_nodes--
disc_update()
read req->num_nodes
write req->timer_intv
disc_timeout()
read req->num_nodes
read/write req->timer_intv
Without lock protection, the only symptom of a race is that discovery
messages occasionally may not be sent out. This is not fatal, since such
messages are best-effort anyway. On the other hand, since discovery
messages are not time critical, adding a protecting lock brings no
serious overhead either. So we add a new, dedicated spinlock in
order to guarantee absolute data consistency in link_req objects.
This also helps reduce the overall role of the bearer_lock, which
we want to remove completely in a later commit series.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag 'has_redundant_link' is defined only in RESET and ACTIVATE
protocol messages. Due to an ambiguity in the protocol specification it
is currently also transferred in STATE messages. Its value is used to
initialize a link state variable, 'permit_changeover', which is used
to inhibit futile link failover attempts when it is known that the
peer node has no working links at the moment, although the local node
may still think it has one.
The fact that 'has_redundant_link' incorrectly is read from STATE
messages has the effect that 'permit_changeover' sometimes gets a wrong
value, and permanently blocks any links from being re-established. Such
failures can only occur in in dual-link systems, and are extremely rare.
This bug seems to have always been present in the code.
Furthermore, since commit b4b5610223
("tipc: Ensure both nodes recognize loss of contact between them"),
the 'permit_changeover' field serves no purpose any more. The task of
enforcing 'lost contact' cycles at both peer endpoints is now taken
by a new mechanism, using the flags WAIT_NODE_DOWN and WAIT_PEER_DOWN
in struct tipc_node to abort unnecessary failover attempts.
We therefore remove the 'has_redundant_link' flag from STATE messages,
as well as the now redundant 'permit_changeover' variable.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functionality related to link addition and failover is unnecessarily
hard to understand and maintain. We try to improve this by renaming
some of the functions, at the same time adding or improving the
explanatory comments around them. Names such as "tipc_rcv()" etc. also
align better with what is used in other networking components.
The changes in this commit are purely cosmetic, no functional changes
are made.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
The following patchset contains two patches:
* fix the IRC NAT helper which was broken when adding (incomplete) IPv6
support, from Daniel Borkmann.
* Refine the previous bugtrap that Jesper added to catch problems for the
usage of the sequence adjustment extension in IPVs in Dec 16th, it may
spam messages in case of finding a real bug.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCI-DMA-mapping.txt moved to general docs and became DMA-API-HOWTO.txt
in 5e07c2c730 ("Documentation: rename PCI/PCI-DMA-mapping.txt to
DMA-API-HOWTO.txt"). Add new file about PCI Express I/O Virtualization.
Signed-off-by: Erik Ekman <erik@kryo.se>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We should const-ify comparisons on skb_queue_* inline helper
functions as their parameters are const as well, so lets not
drop that.
Suggested-by: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix three warnings related to:
net/xfrm/xfrm_policy.c:1644:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
net/xfrm/xfrm_policy.c:1656:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
net/xfrm/xfrm_policy.c:1668:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
Just removing the inline keyword is sufficient as the compiler will
decide on its own about inlining or not.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Try to allocate space for 64-bit BARs above 4G first, to preserve the space
below 4G for 32-bit BARs. If there's no space above 4G available, fall
back to allocating anywhere.
[bhelgaas: reworked starting from http://lkml.kernel.org/r/1387485843-17403-2-git-send-email-yinghai@kernel.org]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When allocating space for 32-bit BARs, we previously limited RESOURCE
addresses so they would fit in 32 bits. However, the BUS address need not
be the same as the resource address, and it's the bus address that must fit
in the 32-bit BAR.
This patch adds:
- pci_clip_resource_to_region(), which clips a resource so it contains
only the range that maps to the specified bus address region, e.g., to
clip a resource to 32-bit bus addresses, and
- pci_bus_alloc_from_region(), which allocates space for a resource from
the specified bus address region,
and changes pci_bus_alloc_resource() to allocate space for 64-bit BARs from
the entire bus address region, and space for 32-bit BARs from only the bus
address region below 4GB.
If we had this window:
pci_root HWP0002:0a: host bridge window [mem 0xf0180000000-0xf01fedfffff] (bus address [0x80000000-0xfedfffff])
we previously could not put a 32-bit BAR there, because the CPU addresses
don't fit in 32 bits. This patch fixes this, so we can use this space for
32-bit BARs.
It's also possible (though unlikely) to have resources with 32-bit CPU
addresses but bus addresses above 4GB. In this case the previous code
would allocate space that a 32-bit BAR could not map.
Remove PCIBIOS_MAX_MEM_32, which is no longer used.
[bhelgaas: reworked starting from http://lkml.kernel.org/r/1386658484-15774-3-git-send-email-yinghai@kernel.org]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_bus_alloc_resource() avoids allocating space below the "min" supplied
by the caller (usually PCIBIOS_MIN_IO or PCIBIOS_MIN_MEM). This is to
protect badly documented motherboard resources. But if we're allocating
space inside an already-configured PCI-PCI bridge window, we ignore "min".
See 688d191821 ("pci: make bus resource start address override minimum IO
address").
This patch moves the check to make it more visible and simplify future
patches. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The ct expression can currently not be used in the inet family since
we don't have a conntrack module for NFPROTO_INET, so
nf_ct_l3proto_try_module_get() fails. Add some manual handling to
load the modules for both NFPROTO_IPV4 and NFPROTO_IPV6 if the
ct expression is used in the inet family.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
For L3-proto independant rules we need to get at the L4 protocol value
directly. Add it to the nft_pktinfo struct and use the meta expression
to retrieve it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Needed by multi-family tables to distinguish IPv4 and IPv6 packets.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds a new table family and a new filter chain that you can
use to attach IPv4 and IPv6 rules. This should help to simplify
rule-set maintainance in dual-stack setups.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add support to register chains to multiple hooks for different address
families for mixed IPv4/IPv6 tables.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Multi-family tables need the AF from the hook ops. Add a pointer to the
hook ops and replace usage of the hooknum member in struct nft_pktinfo.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently the AF-specific hook functions override the chain-type specific
hook functions. That doesn't make too much sense since the chain types
are a special case of the AF-specific hooks.
Make the AF-specific hook functions the default and make the optional
chain type hooks override them.
As a side effect, the necessary code restructuring reduces the code size,
f.i. in case of nf_tables_ipv4.o:
nf_tables_ipv4_init_net | -24
nft_do_chain_ipv4 | -113
2 functions changed, 137 bytes removed, diff: -137
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
net/netfilter/nft_reject.c: In function 'nft_reject_eval':
net/netfilter/nft_reject.c:37:14: warning: unused variable 'net' [-Wunused-variable]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The Cubietruck makes use of the first three i2c controllers found on the
Allwinner A20; i2c-0 is used internally for the PMIC, i2c-1 is exposed on
the board headers, and i2c-2 is used for DDC on the VGA connector. This
patch enables them in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
