USB function's configfs config group is created in a generic way in
usb/gadget/configfs.c:function_make(), which in turn delegates actual
allocation and setup of the USB function instance to a particular
implementation, e.g. in f_acm.c. The said implementation does its job
in a parameter-less function e.g. acm_alloc_instance(), which results
in creating an unnamed config group, whose name is set later in
function_make(). function_make() creates the name by parsing a string
of the form:
<function name>.<instance name>
which comes from userspace as a parameter to mkdir invocation.
Up to now only <function name> has been used, while <instance name>
has been ignored. This patch adds a set_inst_name() operation to
struct usb_function_instance which allows passing the <instance name>
from function_make() so that it is not ignored. It is entirely up to the
implementor of set_inst_name() what to do with the <instance name>.
In a typical case, the struct usb_function_instance is embedded in a
larger struct which is retrieved in set_inst_name() with container_of(),
and the larger struct contains a field to store the <instance name>.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds flushing TX FIFO in kill_all_requests() function in
dedicated-fifo mode. It's because when requests are killed (when endpoint is
disabled or in case of device reset/disconnection) in FIFO can stay some
unsent data. In the worst case FIFO can stay full, and then if endpoint will
be back enabled, sending new data will be impossible.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch set maximum possible maxpacket value for each speed. Previous
values didn't allow to use maxpacket sizes greater than 64 in full speed
and 512 in high speed, although hardware is able to handle up to 1023 in fs
and 1024 in hs.
Tested-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to initialize the notifer before use it.
So lets initialize it when add a new phy device to
reduce the code redundancy.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DMAEngine uses IRQ if dma_request_channel() was called,
and it is using devm_request_irq() today,
OTOH, dma_request_channel() will be called when each
USB connection happened on this driver.
This means same IRQ will be requested many times
whenever each USB connected,
and this IRQ isn't freed when USB disconnected.
Request DMAEngine once.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add Keystone platform USB PHY driver support. Current main purpose
of this driver is to enable the PHY reference clock gate on the
Keystone SoC. Otherwise it is a nop PHY.
[ balbi@ti.com : add COMPILE_TEST as a possible dependency
make sure drvdata is initialized before adding PHY ]
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull media fixes from Mauro Carvalho Chehab:
"A dvb core deadlock fix, a couple videobuf2 fixes an a series of media
driver fixes"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (30 commits)
[media] videobuf2-dma-sg: fix possible memory leak
[media] vb2: regression fix: always set length field.
[media] mt9p031: Include linux/of.h header
[media] rtl2830: add parent for I2C adapter
[media] media: marvell-ccic: use devm to release clk
[media] ths7303: Declare as static a private function
[media] em28xx-video: Swap release order to avoid lock nesting
[media] usbtv: Add support for PAL video source
[media] media_tree: Fix spelling errors
[media] videobuf2: Add support for file access mode flags for DMABUF exporting
[media] radio-shark2: Mark shark_resume_leds() inline to kill compiler warning
[media] radio-shark: Mark shark_resume_leds() inline to kill compiler warning
[media] af9035: unlock on error in af9035_i2c_master_xfer()
[media] af9033: fix broken I2C
[media] v4l: omap3isp: Don't check for missing get_fmt op on remote subdev
[media] af9035: fix broken I2C and USB I/O
[media] wm8775: fix broken audio routing
[media] marvell-ccic: drop resource free in driver remove
[media] tef6862/radio-tea5764: actually assign clamp result
[media] cx231xx: use after free on error path in probe
...
Fix HIH-6130 driver to work with BeagleBone
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=B6Bw
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix HIH-6130 driver to work with BeagleBone"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: HIH-6130: Support I2C bus drivers without I2C_FUNC_SMBUS_QUICK
Pull hwmon fixes from Jean Delvare.
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: Prevent some divide by zeros in FAN_TO_REG()
hwmon: (w83l768ng) Fix fan speed control range
hwmon: (w83l786ng) Fix fan speed control mode setting and reporting
hwmon: (lm90) Unregister hwmon device if interrupt setup fails
This allows the module to be loaded automatically.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit c45f812f02 ('8390 : Replace ei_debug with msg_enable/NETIF_MSG_*
feature') ended up moving the printout of version[] from something that
will be compiled out due to defines, to something that is now evaluated
at runtime.
That means that what always used to be an access to an __initdata string
from non-__init code started showing up as a section mismatch when it
didn't before.
All other 8390 versions skip __initdata on the version string, and
starting to annotate the whole chain of callers with __init seems like
more churn than it's worth on this driver, so remove it from etherh.c as well.
Fixes: c45f812f02 ('8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature')
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should be writing bits here but instead we're writing the
numbers that correspond to the bits we want to write. Fix it by
wrapping the numbers in the BIT() macro. This fixes gpios acting
as interrupts.
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch modifies the GRO stack to avoid the use of "network_header"
and associated macros like ip_hdr() and ipv6_hdr() in order to allow
an arbitary number of IP hdrs (v4 or v6) to be used in the
encapsulation chain. This lays the foundation for various IP
tunneling support (IP-in-IP, GRE, VXLAN, SIT,...) to be added later.
With this patch, the GRO stack traversing now is mostly based on
skb_gro_offset rather than special hdr offsets saved in skb (e.g.,
skb->network_header). As a result all but the top layer (i.e., the
the transport layer) must have hdrs of the same length in order for
a pkt to be considered for aggregation. Therefore when adding a new
encap layer (e.g., for tunneling), one must check and skip flows
(e.g., by setting NAPI_GRO_CB(p)->same_flow to 0) that have a
different hdr length.
Note that unlike the network header, the transport header can and
will continue to be set by the GRO code since there will be at
most one "transport layer" in the encap chain.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CPSW and Davinci MDIO are build as modules, CPSW crashes when
accessing CPSW registers in CPSW probe. The same is working in built-in
as the CPSW clocks are enabled in Davindi MDIO probe, SO Enabling the
clocks before accessing the version register and moving out the other
register access to cpsw device open.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whilst architectures may be able to do better than this (which they can,
by simply defining their own macro), this is a generic stab at a
zero_bytemask implementation for the asm-generic, big-endian
word-at-a-time implementation.
On arm64, a clz instruction is used to implement the fls efficiently.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When explicitly hashing the end of a string with the word-at-a-time
interface, we have to be careful which end of the word we pick up.
On big-endian CPUs, the upper-bits will contain the data we're after, so
ensure we generate our masks accordingly (and avoid hashing whatever
random junk may have been sitting after the string).
This patch adds a new dcache helper, bytemask_from_count, which creates
a mask appropriate for the CPU endianness.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vlad Yasevich says:
====================
Add packet capture support on macvtap device
Change from RFC:
- moved to the rx_handler approach.
This series adds support for packet capturing on macvtap device.
The initial approach was to simply export the capturing code as
a function from the core network. While simple, it was not
a very architecturally clean approach.
The new appraoch is to provide macvtap with its rx_handler which can
is attached to the macvtap device itself. Macvlan will simply requeue
the packet with an updated skb->dev. BTW, macvlan layer already does this
for macvlan devices. So, now macvtap and macvlan have almost the
same exact input path.
I've toyed with short-circuting the input path for macvtap by returning
RX_HANDLER_ANOTHER, but that just made the code more complicated and
didn't provide any kind of measurable gain (at least according to
netperf and perf runs on the host).
To see if there was a performance regression, I ran 1, 2 and 4 netperf
STREAM and MAERTS tests agains the VM from both remote host and another
guest on the same system. The command ran was
netperf -H $host -t $test -l 20 -i 10 -I 95 -c -C
The numbers I was getting with the new code were consistently very
slightly (1-2%) better then the old code. I don't consider this
an improvement, but it's not a regression! :)
Running 'perf record' on the host didn't show any new hot spots
and cpu utilization stayed about the same. This was better
then I expected from simply looking at the code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since now macvlan and macvtap use the same receive and
forward handlers, we can remove them completely and use
netif_rx and dev_forward_skb() directly.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macvtap device currently doesn not allow a user to capture
traffic on due to the fact that it steals the packets
from the network stack before the skb->dev is set correctly
on the receive side, and that use uses macvlan transmit
path directly on the send side. As a result, we never
get a change to give traffic to the taps while the correct
device is set in the skb.
This patch makes macvtap device behave almost exaclty like
macvlan. On the send side, we switch to using dev_queue_xmit().
On the receive side, to deliver packets to macvtap, we now
use netif_rx and dev_forward_skb just like macvlan. The only
differnce now is that macvtap has its own rx_handler which is
attached to the macvtap netdev. It is here that we now steal
the packet and provide it to the socket.
As a result, we can now capture traffic on the macvtap device:
tcpdump -i macvtap0
It also gives us the abilit to add tc actions to the macvtap
device and actually utilize different bandwidth management
queues on output.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pincontrol driver for Tegra124 is build through config
PINCTRL_TEGRA124. Select this config option whenever Tegra124
SoC is enabled.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch changes the RING_FINAL_CHECK_FOR_REQUESTS in
xenvif_build_tx_gops to a check for RING_HAS_UNCONSUMED_REQUESTS as the
former call has the side effect of advancing the ring event pointer and
therefore inviting another interrupt from the frontend before the napi
poll has actually finished, thereby defeating the point of napi.
The event pointer is updated by RING_FINAL_CHECK_FOR_REQUESTS in
xenvif_poll, the napi poll function, if the work done is less than the
budget i.e. when actually transitioning back to interrupt mode.
Reported-by: Malcolm Crossley <malcolm.crossley@citrix.com>
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netback seems to be somewhat confused about the napi budget parameter. The
parameter is supposed to limit the number of skbs processed in each poll,
but netback has this confused with grant operations.
This patch fixes that, properly limiting the work done in each poll. Note
that this limit makes sure we do not process any more data from the shared
ring than we intend to pass back from the poll. This is important to
prevent tx_queue potentially growing without bound.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices drivers make use of optional GPIO parameters. For such
drivers, it is important to discriminate between the case where no
GPIO mapping has been defined for the function they are requesting, and
the case where a mapping exists but an error occured while resolving it
or when acquiring the GPIO.
This patch changes the family of gpiod_get() functions such that they
will return -ENOENT if and only if no GPIO mapping is defined for the
requested function. Other error codes are used when an actual error
occured during the GPIO resolution.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
table walks and a couple other issues.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=9WG5
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-for-v3.13-rc4' of git://github.com/awilliam/linux-vfio
Pull iommu fixes from Alex Williamson:
"arm/smmu driver updates via Will Deacon fixing locking around page
table walks and a couple other issues"
* tag 'iommu-fixes-for-v3.13-rc4' of git://github.com/awilliam/linux-vfio:
iommu/arm-smmu: fix error return code in arm_smmu_device_dt_probe()
iommu/arm-smmu: remove potential NULL dereference on mapping path
iommu/arm-smmu: use mutex instead of spinlock for locking page tables
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=/AdA
-----END PGP SIGNATURE-----
Merge tag 'keys-devel-20131210' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull misc keyrings fixes from David Howells:
"These break down into five sets:
- A patch to error handling in the big_key type for huge payloads.
If the payload is larger than the "low limit" and the backing store
allocation fails, then big_key_instantiate() doesn't clear the
payload pointers in the key, assuming them to have been previously
cleared - but only one of them is.
Unfortunately, the garbage collector still calls big_key_destroy()
when sees one of the pointers with a weird value in it (and not
NULL) which it then tries to clean up.
- Three patches to fix the keyring type:
* A patch to fix the hash function to correctly divide keyrings off
from keys in the topology of the tree inside the associative
array. This is only a problem if searching through nested
keyrings - and only if the hash function incorrectly puts the a
keyring outside of the 0 branch of the root node.
* A patch to fix keyrings' use of the associative array. The
__key_link_begin() function initially passes a NULL key pointer
to assoc_array_insert() on the basis that it's holding a place in
the tree whilst it does more allocation and stuff.
This is only a problem when a node contains 16 keys that match at
that level and we want to add an also matching 17th. This should
easily be manufactured with a keyring full of keyrings (without
chucking any other sort of key into the mix) - except for (a)
above which makes it on average adding the 65th keyring.
* A patch to fix searching down through nested keyrings, where any
keyring in the set has more than 16 keyrings and none of the
first keyrings we look through has a match (before the tree
iteration needs to step to a more distal node).
Test in keyutils test suite:
http://git.kernel.org/cgit/linux/kernel/git/dhowells/keyutils.git/commit/?id=8b4ae963ed92523aea18dfbb8cab3f4979e13bd1
- A patch to fix the big_key type's use of a shmem file as its
backing store causing audit messages and LSM check failures. This
is done by setting S_PRIVATE on the file to avoid LSM checks on the
file (access to the shmem file goes through the keyctl() interface
and so is gated by the LSM that way).
This isn't normally a problem if a key is used by the context that
generated it - and it's currently only used by libkrb5.
Test in keyutils test suite:
http://git.kernel.org/cgit/linux/kernel/git/dhowells/keyutils.git/commit/?id=d9a53cbab42c293962f2f78f7190253fc73bd32e
- A patch to add a generated file to .gitignore.
- A patch to fix the alignment of the system certificate data such
that it it works on s390. As I understand it, on the S390 arch,
symbols must be 2-byte aligned because loading the address discards
the least-significant bit"
* tag 'keys-devel-20131210' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
KEYS: correct alignment of system_certificate_list content in assembly file
Ignore generated file kernel/x509_certificate_list
security: shmem: implement kernel private shmem inodes
KEYS: Fix searching of nested keyrings
KEYS: Fix multiple key add into associative array
KEYS: Fix the keyring hash function
KEYS: Pre-clear struct key on allocation
- fix for buffer overrun in agfl with growfs on v4 superblock
- return EINVAL if requested discard length is less than a block
- fix possible memory corruption in xfs_attrlist_by_handle()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=SbPd
-----END PGP SIGNATURE-----
Merge tag 'xfs-for-linus-v3.13-rc4' of git://oss.sgi.com/xfs/xfs
Pull xfs bugfixes from Ben Myers:
- fix for buffer overrun in agfl with growfs on v4 superblock
- return EINVAL if requested discard length is less than a block
- fix possible memory corruption in xfs_attrlist_by_handle()
* tag 'xfs-for-linus-v3.13-rc4' of git://oss.sgi.com/xfs/xfs:
xfs: growfs overruns AGFL buffer on V4 filesystems
xfs: don't perform discard if the given range length is less than block size
xfs: underflow bug in xfs_attrlist_by_handle()
ops->pin_config_get() is only used in one specific path that will only be taken
for generic pinconf drivers (ops->is_generic == true) when dumping the pinconf
by using debugfs.
By removing the check in pinconf_check_ops(), let's stop pressuring people to
write a pin_config_get() function that will never be used and so will probably
never be tested.
Removing the check in pinconf_pins_show() allows driver to not implement
pin_config_get() but still get a dump of the pinconf in debugfs by implementing
pin_config_dbg_show().
Finally, not implementing pin_config_get() now results in returning -ENOTSUPP
instead of -EINVAL. While this doesn't have any real impact for now, this feels
more right.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This AT91 specific Kconfig option removed the code that dealt with
programmable clocks. Each AT91 SoC embeds programmable clocks and
there is little gain to remove this code in case that such a clock
is not used.
If this option is not selected, it causes certain drivers to fail
to build. We simply remove this option instead of adding code just
to build a workaround.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
When debugging the read-only hugepage case, I was confused by the fact
that get_futex_key() did an access_ok() only for the non-shared futex
case, since the user address checking really isn't in any way specific
to the private key handling.
Now, it turns out that the shared key handling does effectively do the
equivalent checks inside get_user_pages_fast() (it doesn't actually
check the address range on x86, but does check the page protections for
being a user page). So it wasn't actually a bug, but the fact that we
treat the address differently for private and shared futexes threw me
for a loop.
Just move the check up, so that it gets done for both cases. Also, use
the 'rw' parameter for the type, even if it doesn't actually matter any
more (it's a historical artifact of the old racy i386 "page faults from
kernel space don't check write protections").
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Depending on peripheral capabilities, print SHA information at the end
of the probe function.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for Device Tree and use of the DMA DT API to
get the channels if needed.
Documentation is added for these DT nodes.
Initial code by: Nicolas Royer and Eukrea.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for Device Tree and use of the DMA DT API to
get the channels if needed.
Documentation is added for these DT nodes.
Initial code by: Nicolas Royer and Eukrea.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for Device Tree and use of the DMA DT API to
get the needed channels.
Documentation is added for these DT nodes.
Initial code by: Nicolas Royer and Eukrea.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
The hugepage code had the exact same bug that regular pages had in
commit 7485d0d375 ("futexes: Remove rw parameter from
get_futex_key()").
The regular page case was fixed by commit 9ea71503a8 ("futex: Fix
regression with read only mappings"), but the transparent hugepage case
(added in a5b338f2b0: "thp: update futex compound knowledge") case
remained broken.
Found by Dave Jones and his trinity tool.
Reported-and-tested-by: Dave Jones <davej@fedoraproject.org>
Cc: stable@kernel.org # v2.6.38+
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Darren Hart <dvhart@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This causes a race condition between drm_dev_unregister()
and pci_driver.shutdown at shutdown or driver unload time.
We need to revisit how to properly support kexec within
the drm.
This reverts commit 846ae41ae9.
Otherwise we end up with a rather strange looking result.
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Tom Stellard <thomas.stellard@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
I implemented support for this, but forget to hook
up the callback so the driver can actually use it.
On asics with a dedicated DMA engine, we use the DMA
engine for buffer migration so this is just for testing
purposes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit ec39f64bba (drm/radeon/dpm: Convert
to use devm_hwmon_register_with_groups) converted one usage of
dev_get_drvdata, but there were two more.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=72457
Signed-off-by: Martin Andersson <g02maran@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
While enabling these machines, we found we would sometimes lose an
interrupt if we change hardware volume during playback, and that
disabling msi fixed this issue. (Losing the interrupt caused underruns
and crackling audio, as the one second timeout is usually bigger than
the period size.)
The machines were all machines from HP, running AMD Hudson controller,
and Realtek ALC282 codec.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1260225
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is an inconsistency in the handling of SUID/SGID file
bits after chown() between NFS and other local file systems.
Local file systems (for example, ext3, ext4, xfs, btrfs) revoke
SUID/SGID bits after chown() on a regular file even if
the owner/group of the file has not been changed:
~# touch file; chmod ug+s file; chmod u+x file
~# ls -l file
-rwsr-Sr-- 1 root root 0 Dec 6 04:49 file
~# chown root file; ls -l file
-rwxr-Sr-- 1 root root 0 Dec 6 04:49 file
but NFS doesn't do that:
~# touch file; chmod ug+s file; chmod u+x file
~# ls -l file
-rwsr-Sr-- 1 root root 0 Dec 6 04:49 file
~# chown root file; ls -l file
-rwsr-Sr-- 1 root root 0 Dec 6 04:49 file
NFS does that only if the owner/group has been changed:
~# touch file; chmod ug+s file; chmod u+x file
~# ls -l file
-rwsr-Sr-- 1 root root 0 Dec 6 05:02 file
~# chown bin file; ls -l file
-rwxr-Sr-- 1 bin root 0 Dec 6 05:02 file
See: http://pubs.opengroup.org/onlinepubs/9699919799/functions/chown.html
"If the specified file is a regular file, one or more of
the S_IXUSR, S_IXGRP, or S_IXOTH bits of the file mode are set,
and the process has appropriate privileges, it is
implementation-defined whether the set-user-ID and set-group-ID
bits are altered."
So both variants are acceptable by POSIX.
This patch makes NFS to behave like local file systems.
Signed-off-by: Stanislav Kholmanskikh <stanislav.kholmanskikh@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
hex_pack_byte() is a fast way to convert a byte in its ASCII representation. We
may use it instead of custom approach.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Add the missing unlock before return from function cgroup_load_subsys()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
The closing parenthesis is in the wrong place. We want to check
"sizeof(*arg->clone_sources) * arg->clone_sources_count" instead of
"sizeof(*arg->clone_sources * arg->clone_sources_count)".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jie Liu <jeff.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
cc: stable@vger.kernel.org
I hit an oops when merging reloc roots fails, the reason is that
new reloc roots may be added and we should make sure we cleanup
all reloc roots.
Signed-off-by: Wang Shilong <wangsl.fnst@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
Quota tree and UUID Tree is only cowed, they can not be snapshoted.
Signed-off-by: Wang Shilong <wangsl.fnst@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
I hit an oops when inserting reloc root into @reloc_root_tree(it can be
easily triggered when forcing cow for relocation root)
[ 866.494539] [<ffffffffa0499579>] btrfs_init_reloc_root+0x79/0xb0 [btrfs]
[ 866.495321] [<ffffffffa044c240>] record_root_in_trans+0xb0/0x110 [btrfs]
[ 866.496109] [<ffffffffa044d758>] btrfs_record_root_in_trans+0x48/0x80 [btrfs]
[ 866.496908] [<ffffffffa0494da8>] select_reloc_root+0xa8/0x210 [btrfs]
[ 866.497703] [<ffffffffa0495c8a>] do_relocation+0x16a/0x540 [btrfs]
This is because reloc root inserted into @reloc_root_tree is not within one
transaction,reloc root may be cowed and root block bytenr will be reused then
oops happens.We should update reloc root in @reloc_root_tree when cow reloc
root node, fix it.
Signed-off-by: Wang Shilong <wangsl.fnst@cn.fujitsu.com>
Reviewed-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
Currently extent-tree.c:btrfs_lookup_extent_info() can miss the lookup
of skinny extent items. This can happen when the execution flow is the
following:
* We do an extent tree lookup and fail to find a skinny extent item;
* As a result, we attempt to see if a non-skinny extent item exists,
either by looking at previous item in the leaf or by doing another
full extent tree search;
* We have a transaction and then we check for a matching delayed ref
head in the transaction's delayed refs rbtree;
* We find such delayed ref head and then we try to lock it with a
call to mutex_trylock();
* The lock was contended so we jump to the label "again", which repeats
the extent tree search but for a non-skinny extent item, because we set
previously metadata variable to 0 and the search key to look for a
non-skinny extent-item;
* After the jump (and after releasing the transaction's delayed refs
lock), a skinny extent item might have been added to the extent tree
but we will miss it because metadata is set to 0 and the search key
is set for a non-skinny extent-item.
The fix here is to not reset metadata to 0 and to jump to the initial search
key setup if the delayed ref head is contended, instead of jumping directly
to the extent tree search label ("again").
This issue was found while investigating the issue reported at Bugzilla 64961.
David Sterba suspected this function was missing extent items, and that
this could be caused by the last change to this function, which was made
in the following patch:
[PATCH] Btrfs: optimize btrfs_lookup_extent_info()
(commit 74be951087)
But in fact this issue already existed before, because after failing to find
a skinny extent item, the code set the search key for a non-skinny extent
item, and on contention of a matching delayed ref head it would not search
the extent tree for a skinny extent item anymore.
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
