These seem to show up when building for architectures other than ARM,
which I guess will never happen. The reason why the kbuild test bot ran
into these was a missing dependency which has hence been fixed. Still it
doesn't hurt to fix them anyway.
Reported-by: kbuild test bot <fengguang.wu@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use EDID data to determine whether the display supports HDMI or DVI
only. The HDMI output used to assume to be connected to HDMI displays,
but that broke support for DVI displays that don't understand the
interspersed audio/other data.
To be on the safe side, default to DVI if no EDID data is available.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
[treding@nvidia.com: move detection to separate function]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra114 TMDS configuration requires a new peak_current field and the
driver current override bit has changed position.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a structure to parameterize the code to handle differences between
the HDMI hardware on various SoC generations. This removes the need to
clutter the code with checks for individual compatible values.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Everything related to Tegra uses Tegra20 and Tegra30 instead of Tegra2
and Tegra3, respectively. Rename the TMDS arrays in the HDMI driver for
consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since the .init() and .exit() functions are executed whenever the DRM
driver is loaded or unloaded, care must be taken not to use them for
resource allocation. Otherwise deferred probing cannot be used, since
the .init() and .exit() are not run at probe time. Similarly the code
that frees resources must be run at .remove() time. If it is run from
the .exit() function, it can release resources multiple times.
To handle this more consistently, rename the tegra_output_parse_dt()
function to tegra_output_probe() and introduce tegra_output_remove()
which can be used to free output-related resources.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the DRM driver is unloaded, all the associated resources must be
cleaned up and zeroed out. This is necessary because of the architecture
of the Tegra DRM driver, where not all subdrivers are unloaded along
with the DRM driver. Therefore device-managed managed won't be freed and
memory cannot be assumed to have been cleared (because it hasn't been
reallocated using kzalloc()) by the time the DRM driver is reloaded. It
is therefore necessary to zero out the structures to prevent strange
errors (such as slab corruptions) from occurring.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra DRM driver currently uses some infrastructure to defer the DRM
core initialization until all required devices have registered. The same
infrastructure can potentially be used by any other driver that requires
more than a single sub-device of the host1x module.
Make the infrastructure more generic and keep only the DRM specific code
in the DRM part of the driver. Eventually this will make it easy to move
the DRM driver part back to the DRM subsystem.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a new Kconfig choice group which allows to configure how gcc should
tune the generated code (via -mtune option).
By default the -mtune parameter will match the -march parameter.
This is a rather large patch, but I wouldn't know how to make this shorter
unfortunately.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
this_cpu_xor() will be removed tree wide during the next merge window.
To avoid merge conflicts s390's removal comes via the s390 tree.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the ACCESS_ONCE macro for both accesses to idle->sequence in the
loops to calculate the idle time. If only one access uses the macro,
the compiler is free to cache the value for the second access which
can cause endless loops.
Cc: stable@vger.kernel.org # 3.6+
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The get_tod_clock_ext inline assembly does not specify its output
operands correctly. This can cause incorrect code to be generated.
Cc: stable@vger.kernel.org # 3.12
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Adds the driver for the LM3560, dual LED Flash The LM3560 has two 1A
constant current driver for high current white LEDs.
It is controlled via an I2C compatible interface(up to 400kHz).
Each flash brightness, torch brightness and enable/disable can be
controlled independantly, but flash timeout and operation mode are shared.
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Expose the buffer objects, syncpoint and channel functionality in the
public public header so that drivers can use them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This structure derives from host1x_client. DRM-specific fields are moved
from host1x_client to this structure, so that host1x_client can remain
agnostic of DRM.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rename the host1x_to_drm_bo() macro to host1x_to_tegra_bo() for
consistency and fixup various stylistic issues.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Other drivers use the tegra- prefix in their names, so add it to this
driver's name as well for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rework the address table code for the host1x firewall. The previous
implementation allocated a bitfield but didn't check for a valid pointer
so it could potentially crash. Instead, embed a static bitmap within the
gr2d structure to avoid the allocation and use the Linux bitmap API to
reduce code complexity.
Don't annotate the driver's .remove() function __exit. Even if built in
the driver can be unloaded via sysfs, so .remove() needs to stick around
after initialization. Also remove the explicit initialization of the
driver's .owner field to THIS_MODULE because that's now handled by the
driver core.
Furthermore make an error message more consistent with other subdrivers,
index the syncpts array for better readability, remove a gratuituous
newline and reorder some variable declarations to make the code easier
to read.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The same code sequence is used in various places to validate a register
access in the command stream. This can be refactored into a separate
function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The value stored in this field is a pointer to a command buffer, not an
ID. Avoid some confusion by reflecting that in the field's name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Arguments on subsequent lines should be aligned with the first argument.
This one occurrence went unnoticed during code review.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The device can be unbound from the driver via sysfs, so regardless of
whether the driver is builtin or a module, its .remove() function needs
to stick around.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The structure represents a context associated with a particular process
that has opened the Tegra DRM device and requested a channel. This is a
very DRM-specific notion and has nothing to do with host1x. Rename the
structure to more clearly mark the boundaries between the two.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This structure extends drm_file with Tegra DRM specific fields and has
nothing to do with host1x. Rename the structure to more clearly mark the
boundaries between host1x and Tegra DRM.
While at it, move the structure definition out of the header. It's never
used outside of the drm.c source file, so it can be defined within that.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The host1x and Tegra DRM drivers are currently tightly coupled. Renaming
the structure marks the boundary more clearly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The num_relocs count are passed to the kernel per job, not per gather.
For multi-gather jobs, we would previously fail if there were relocs in
other gathers aside from the first one.
Fix this by simply moving the check until all gathers have been
consumed.
Signed-off-by: Erik Faye-Lund <kusmabite@gmail.com>
Reviewed-by: Arto Merilainen <amerilainen@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix a typo (iotcl -> ioctl) in the debug message when an unknown IOCTL
is encountered.
Acked-by: David Airlie <airlied@linux.ie>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When userspace removes the active framebuffer using DRM_IOCTL_MODE_RMFB,
or explicitly disables the CRTC (by calling drmModeSetCrtc(..., NULL)
for example), a NULL framebuffer will be passed to the .set_config()
implementation of a CRTC. The drm_crtc_helper_set_config() helper will
decide to disable a CRTC when that happens.
To do so, it calls drm_crtc_helper_disable(), which in turn will iterate
over all encoders and decouple them from their connectors and finally
call drm_helper_disable_unused_functions() to clean up and call the
.disable() or .dpms() implementation for each encoder. However, at no
point during this sequence does it track the DPMS mode of a connector,
so it will usually remain on after this.
When a connector is enabled again, drm_helper_connector_dpms() will not
notice that the DPMS mode actually changed and won't do anything, which
causes the connector to stay disabled indefinitely.
To prevent this from happening, explicitly set the connector's DPMS mode
to off when the CRTC is disabled. That way it reflects the correct state
and can be enabled again.
This solves an issue observed when terminating an X server running on
the xf86-video-modesetting driver. Without this patch, the connector
would not be enabled properly and the screen would stay dark.
Acked-by: David Airlie <airlied@linux.ie>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Components are RTL2832P + R828D + MN88472.
Currently support only DVB-T as there is no driver for MN88472 demod.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
RTL2832P is version of RTL2832U with extra TS interface.
As for now, we support only integrated RTL2832 demod.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use R820T config for R828D too as those are about same tuner.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Small changes in order to support tuner version R828D @ 16 MHz clock.
There was 'vco_fine_tune' check, which seems to adjust synthesizer
output divider (mixer dix / LO div / Rout) by one. R828D seems to
return vco_fine_tune=1 every time and that condition causes tuning
fail as output divider was increased by one.
Resolve problem by skipping whole condition in case of R828D tuner.
Just to mention, other tuner, R820T, seems to return 2 here.
Synthesizer maximum frequency check was hard coded to check synthesizer N
and thus worked correctly only for clock frequencies around 30 MHz.
As whole test is quite useless in any case, I removed it totally.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Get rid of unnecessary (void *) casting in 'cypress_init' function.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds support for touchpad found on Dell XT2. It's a dual device
with device ID: 73, 00, 14, that comply with "ALPS_PROTO_V2".
Signed-off-by: Yunkang Tang <yunkang.tang@cn.alps.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
v3.12-rc fails to build with this error:
drivers/media/i2c/ths8200.c:49:2: error: unknown field 'bt' specified in initializer
drivers/media/i2c/ths8200.c:50:3: error: field name not in record or union initializer
drivers/media/i2c/ths8200.c:50:3: error: (near initialization for 'ths8200_timings_cap.reserved')
drivers/media/i2c/ths8200.c:51:3: error: field name not in record or union initializer
drivers/media/i2c/ths8200.c:51:3: error: (near initialization for 'ths8200_timings_cap.reserved')
...
with gcc 4.5.4. This error was not detected in builds prior to v3.12-rc.
This patch fixes this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: stable@vger.kernel.org # For kernel v3.12
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support for the UB435-Q V2. You might need to
use the device once with the Windows driver provided by KWorld
in order to permanently reprogram the device descriptors. Thanks
to Jarod Wilson for the initial attempt at adding support for this
device.
[m.chehab@samsung.com: Fixed Whitespace mangling, Coding Style and
improved the error handling at DVB attach]
Signed-off-by: Jean-Francois Thibert <jfthibert@google.com>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Previously, f2fs_sync_file() waits for all the node blocks to be written.
But, we don't need to do that, but wait only the inode-related node blocks.
This patch adds wait_on_node_pages_writeback() in which waits inode-related
node blocks that are on writeback.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Fix build error when VIDEOBUF2_CORE=m and USB_MSI3101=y.
drivers/built-in.o: In function `msi3101_buf_queue':
sdr-msi3101.c:(.text+0x1298d6): undefined reference to `vb2_buffer_done'
drivers/built-in.o: In function `msi3101_cleanup_queued_bufs':
sdr-msi3101.c:(.text+0x1299c7): undefined reference to `vb2_buffer_done'
drivers/built-in.o: In function `msi3101_isoc_handler':
sdr-msi3101.c:(.text+0x12a08d): undefined reference to `vb2_plane_vaddr'
sdr-msi3101.c:(.text+0x12a0b9): undefined reference to `vb2_buffer_done'
drivers/built-in.o: In function `msi3101_probe':
sdr-msi3101.c:(.text+0x12a1c5): undefined reference to `vb2_vmalloc_memops'
sdr-msi3101.c:(.text+0x12a1d7): undefined reference to `vb2_queue_init'
drivers/built-in.o:(.rodata+0x34cf0): undefined reference to `vb2_ioctl_reqbufs'
drivers/built-in.o:(.rodata+0x34cf4): undefined reference to `vb2_ioctl_querybuf'
drivers/built-in.o:(.rodata+0x34cf8): undefined reference to `vb2_ioctl_qbuf'
drivers/built-in.o:(.rodata+0x34d00): undefined reference to `vb2_ioctl_dqbuf'
drivers/built-in.o:(.rodata+0x34d04): undefined reference to `vb2_ioctl_create_bufs'
drivers/built-in.o:(.rodata+0x34d08): undefined reference to `vb2_ioctl_prepare_buf'
drivers/built-in.o:(.rodata+0x34d18): undefined reference to `vb2_ioctl_streamon'
drivers/built-in.o:(.rodata+0x34d1c): undefined reference to `vb2_ioctl_streamoff'
drivers/built-in.o:(.rodata+0x35580): undefined reference to `vb2_fop_read'
drivers/built-in.o:(.rodata+0x35588): undefined reference to `vb2_fop_poll'
drivers/built-in.o:(.rodata+0x35598): undefined reference to `vb2_fop_mmap'
drivers/built-in.o:(.rodata+0x355a0): undefined reference to `vb2_fop_release'
drivers/built-in.o:(.data+0x23b40): undefined reference to `vb2_ops_wait_prepare'
drivers/built-in.o:(.data+0x23b44): undefined reference to `vb2_ops_wait_finish'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
i2c_adap is a field of a struct and will always be allocated so
its address will never be null.
Suggested by coccinelle, manually verified.
Signed-off-by: Alexandru Juncu <alexj@rosedu.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
