This moves the code in book3s_hv_rmhandlers.S that reads any pending
interrupt from the XICS interrupt controller, and works out whether
it is an IPI for the guest, an IPI for the host, or a device interrupt,
into a new function called kvmppc_read_intr. Later patches will
need this.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
We have two paths into and out of the low-level guest entry and exit
code: from a vcpu task via kvmppc_hv_entry_trampoline, and from the
system reset vector for an offline secondary thread on POWER7 via
kvm_start_guest. Currently both just branch to kvmppc_hv_entry to
enter the guest, and on guest exit, we test the vcpu physical thread
ID to detect which way we came in and thus whether we should return
to the vcpu task or go back to nap mode.
In order to make the code flow clearer, and to keep the code relating
to each flow together, this turns kvmppc_hv_entry into a subroutine
that follows the normal conventions for call and return. This means
that kvmppc_hv_entry_trampoline() and kvmppc_hv_entry() now establish
normal stack frames, and we use the normal stack slots for saving
return addresses rather than local_paca->kvm_hstate.vmhandler. Apart
from that this is mostly moving code around unchanged.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The H_CONFER hypercall is used when a guest vcpu is spinning on a lock
held by another vcpu which has been preempted, and the spinning vcpu
wishes to give its timeslice to the lock holder. We implement this
in the straightforward way using kvm_vcpu_yield_to().
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The VRSAVE register value for a vcpu is accessible through the
GET/SET_SREGS interface for Book E processors, but not for Book 3S
processors. In order to make this accessible for Book 3S processors,
this adds a new register identifier for GET/SET_ONE_REG, and adds
the code to implement it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This allows guests to have a different timebase origin from the host.
This is needed for migration, where a guest can migrate from one host
to another and the two hosts might have a different timebase origin.
However, the timebase seen by the guest must not go backwards, and
should go forwards only by a small amount corresponding to the time
taken for the migration.
Therefore this provides a new per-vcpu value accessed via the one_reg
interface using the new KVM_REG_PPC_TB_OFFSET identifier. This value
defaults to 0 and is not modified by KVM. On entering the guest, this
value is added onto the timebase, and on exiting the guest, it is
subtracted from the timebase.
This is only supported for recent POWER hardware which has the TBU40
(timebase upper 40 bits) register. Writing to the TBU40 register only
alters the upper 40 bits of the timebase, leaving the lower 24 bits
unchanged. This provides a way to modify the timebase for guest
migration without disturbing the synchronization of the timebase
registers across CPU cores. The kernel rounds up the value given
to a multiple of 2^24.
Timebase values stored in KVM structures (struct kvm_vcpu, struct
kvmppc_vcore, etc.) are stored as host timebase values. The timebase
values in the dispatch trace log need to be guest timebase values,
however, since that is read directly by the guest. This moves the
setting of vcpu->arch.dec_expires on guest exit to a point after we
have restored the host timebase so that vcpu->arch.dec_expires is a
host timebase value.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently we are not saving and restoring the SIAR and SDAR registers in
the PMU (performance monitor unit) on guest entry and exit. The result
is that performance monitoring tools in the guest could get false
information about where a program was executing and what data it was
accessing at the time of a performance monitor interrupt. This fixes
it by saving and restoring these registers along with the other PMU
registers on guest entry/exit.
This also provides a way for userspace to access these values for a
vcpu via the one_reg interface.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This reserves space in get/set_one_reg ioctl for the extra guest state
needed for POWER8. It doesn't implement these at all, it just reserves
them so that the ABI is defined now.
A few things to note here:
- This add *a lot* state for transactional memory. TM suspend mode,
this is unavoidable, you can't simply roll back all transactions and
store only the checkpointed state. I've added this all to
get/set_one_reg (including GPRs) rather than creating a new ioctl
which returns a struct kvm_regs like KVM_GET_REGS does. This means we
if we need to extract the TM state, we are going to need a bucket load
of IOCTLs. Hopefully most of the time this will not be needed as we
can look at the MSR to see if TM is active and only grab them when
needed. If this becomes a bottle neck in future we can add another
ioctl to grab all this state in one go.
- The TM state is offset by 0x80000000.
- For TM, I've done away with VMX and FP and created a single 64x128 bit
VSX register space.
- I've left a space of 1 (at 0x9c) since Paulus needs to add a value
which applies to POWER7 as well.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
A fixup which should be called before codec being freed will come
to use in the next patch.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The LEDs are currently not visible to userspace, for security
reasons. They are exported through thinkpad_acpi.h for use by the
snd-hda-intel driver.
Thanks to Alex Hung <alex.hung@canonical.com> and Takashi Iwai
<tiwai@suse.de> for writing parts of this patch.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the exynos4210_set_apll() function, the APLL frequency is set with
direct register manipulation.
Such approach is not allowed in the common clock framework. The frequency
is changed, but the corresponding clock value is not updated. This causes
wrong frequency read from cpufreq's cpuinfo_cur_freq sysfs attribute.
Also direct manipulation with PLL's S parameter has been removed. It is
already done at PLL35xx code.
Tested at:
- Exynos4210 - Trats board (linux 3.12-rc4)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the exynos4x12_set_apll() function, the APLL frequency is set with
direct register manipulation.
Such approach is not allowed in the common clock framework. The frequency
is changed, but the corresponding clock value is not updated. This causes
wrong frequency read from cpufreq's cpuinfo_cur_freq sysfs attribute.
Also direct manipulation with PLL's S parameter has been removed. It is
already done at PLL35xx code.
Tested at:
- Exynos4412 - Trats2 board (linux 3.12-rc4)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is more idiomatic for the factored out message processing and gives a
small simplification of the code since we always set the per-transfer
parameters in the same fashion.
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
This is a half done conversion with minimal code reorganisation provided
for bisection purposes. A further patch will move the first transfer
preparation into tegra_slink_prepare_message().
The cs_change and udelay handling is removed, these should be
implemented by the framework and in any case are buggy - the two fields
should not be related and the cs_change handling appears to at best only
work the first time it's used in a message.
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
The pan/tilt absolute control value is signed value. If minimum value
is minus, It will be changed to plus by clamp_t() as commit 64ae9958a6.
([media] uvcvideo: Fix control value clamping for unsigned integer controls).
It leads to wrong setting of the control values. For example,
when min and max are -36000 and 36000, the setting value between of this range
is always 36000. So, its data type should be changed to signed.
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/pci/cx25821/cx25821-cards.c:49:20: warning: symbol 'cx25821_bcount' was not declared. Should it be static?
drivers/media/pci/cx25821/cx25821-video-upstream.c:162:33: warning: incorrect type in assignment (different base types)
drivers/media/pci/cx25821/cx25821-video-upstream.c:163:33: warning: incorrect type in assignment (different base types)
drivers/media/pci/cx25821/cx25821-video-upstream.c:164:33: warning: incorrect type in assignment (different base types)
drivers/media/pci/cx25821/cx25821-video-upstream.c:165:33: warning: incorrect type in assignment (different base types)
drivers/media/pci/cx25821/cx25821-medusa-video.h:43:16: warning: symbol '_num_decoders' was not declared. Should it be static?
drivers/media/pci/cx25821/cx25821-medusa-video.h:44:16: warning: symbol '_num_cameras' was not declared. Should it be static?
drivers/media/pci/cx25821/cx25821-medusa-video.h:46:14: warning: symbol '_video_standard' was not declared. Should it be static?
drivers/media/pci/cx25821/cx25821-medusa-video.h:47:5: warning: symbol '_display_field_cnt' was not declared. Should it be static?
After analyzing the last four warnings carefully it became clear that these
variables were really completely unused. As a result of that the call to
medusa_set_decoderduration() is now dubious since the duration is always 0.
Without documentation, however, I can't tell what the right value is.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
struct v4l2_fh has an enum v4l2_priority field. Make sure the enum
definition is available by including linux/videodev2.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
v4l2-fh.h dereferences struct file, the structure must thus be defined.
Pull in its definition by including linux/fs.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove the redundant 'const' qualifiers from the function
signature and from the qmenu_int arrays' declarations.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Increase the streaming_users count only if streaming start succeeds.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix CodingStyle on the GPIO init tables.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are numerous issues in error handling code of cx231xx initialization.
Double free (when cx231xx_init_dev() calls kfree(dev) via cx231xx_release_resources()
and then cx231xx_usb_probe() does the same) and memory leaks
(e.g. usb_get_dev() before (ifnum != 1) check in cx231xx_usb_probe())
are just a few of them.
The patch fixes the issues in cx231xx_usb_probe() and cx231xx_init_dev()
by moving usb_get_dev(interface_to_usbdev(interface)) below in code and
implementing proper error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
module_pci_driver removes some boilerplate and makes code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/common/siano/smsdvb-main.c:47:5: warning: symbol 'sms_to_guard_interval_table' was not declared. Should it be static?
drivers/media/common/siano/smsdvb-main.c:54:5: warning: symbol 'sms_to_code_rate_table' was not declared. Should it be static?
drivers/media/common/siano/smsdvb-main.c:63:5: warning: symbol 'sms_to_hierarchy_table' was not declared. Should it be static?
drivers/media/common/siano/smsdvb-main.c:70:5: warning: symbol 'sms_to_modulation_table' was not declared. Should it be static?
drivers/media/common/siano/smscoreapi.c:925:35: warning: cast to restricted __le32
drivers/media/common/siano/smscoreapi.c:926:28: warning: cast to restricted __le32
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/dvb-usb/az6027.c:257:23: warning: symbol 'az6027_stb0899_config' was not declared. Should it be static?
drivers/media/usb/dvb-usb/az6027.c:294:23: warning: symbol 'az6027_stb6100_config' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drxk_hard.c:1086:62: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxk_hard.c:2784:63: warning: Using plain integer as NULL pointer
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drxd_hard.c:1017:70: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxd_hard.c:1038:69: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxd_hard.c:2836:33: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxd_hard.c:2972:30: warning: Using plain integer as NULL pointer
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
