This removes the DEV_PM_OPS macro and brings this file in line with the
other musb platform drivers.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This makes bfin_pm_ops const and will stub the struct out in case
CONFIG_PM_SLEEP is not set.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This makes am35x_pm_ops const and will stub the struct out in case
CONFIG_PM_SLEEP is not set.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We shouldn't include the simultaneous LE & BR/EDR flags in the LE
advertising data if BR/EDR is disabled on a dual-mode controller. This
patch fixes this issue and ensures that the create_ad function generates
the correct flags when BR/EDR is disabled.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The proximity sensor is connected to pin AH12 on newer HREFs,
that corresponds to pin offset 25 on gpio5, not gpio6.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ambient light sensor is places at address 0x29 nothing else.
This patch makes the ambient light sensor probe again.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The REJECTED management response should mainly be used when the adapter
is in a state where we cannot accept some command or a specific
parameter value. The NOT_SUPPORTED response in turn means that the
adapter really cannot support the command or parameter value.
This patch fixes this distinction and adds two helper functions to
easily get the appropriate LE or BR/EDR related status response.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On dual-mode BR/EDR/LE and LE only controllers it is possible
to configure a random address. There are two types or random
addresses, one is static and the other private. Since the
random private addresses require special privacy feature to
be supported, the configuration of these two are kept separate.
This command allows for setting the static random address. It is
only supported on controllers with LE support. The static random
address is suppose to be valid for the lifetime of the controller
or at least until the next power cycle. To ensure such behavior,
setting of the address is limited to when the controller is
powered off.
The special BDADDR_ANY address (00:00:00:00:00:00) can be used to
disable the static address. This is also the default value.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
batman-adv saves its table of packet handlers as a global state, so handlers
must be set up only once (and setting them up a second time will fail).
The recently-added network coding support tries to set up its handler each time
a new softif is registered, which obviously fails when more that one softif is
used (and in consequence, the softif creation fails).
Fix this by splitting up batadv_nc_init into batadv_nc_init (which is called
only once) and batadv_nc_mesh_init (which is called for each softif); in
addition batadv_nc_free is renamed to batadv_nc_mesh_free to keep naming
consistent.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
... otherwise it is impossible for the low level iommu driver to
figure out which pte flags should be used.
In __map_sg_chunk we can derive the flags from dma_data_direction.
In __iommu_create_mapping we should treat the memory like
DMA_BIDIRECTIONAL and pass both IOMMU_READ and IOMMU_WRITE to
iommu_map.
__iommu_create_mapping is used during dma_alloc_coherent (via
arm_iommu_alloc_attrs). AFAIK dma_alloc_coherent is responsible for
allocation _and_ mapping. I think this implies that access to the
mapped pages should be allowed.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann@calxeda.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Disabling the high speed setting when the controller is powered on has
too many side effects that are not taken care of. And in general it
is not an useful operation anyway. So just make such a command fail
with a rejection error message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We need to use the of_node from the main Arizona device as that
holds our configuration.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch introduces a new mgmt command for enabling/disabling BR/EDR
functionality. This can be convenient when one wants to make a dual-mode
controller behave like a single-mode one. The command is only available
for dual-mode controllers and requires that LE is enabled before using
it. The BR/EDR setting can be enabled at any point, however disabling it
requires the controller to be powered off (otherwise a "rejected"
response will be sent).
Disabling the BR/EDR setting will automatically disable all other BR/EDR
related settings.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To allow treating dual-mode (BR/EDR/LE) controllers as single-mode ones
(LE-only) we want to introduce a new HCI_BREDR_ENABLED flag to track
whether BR/EDR is enabled or not (previously we simply looked at the
feature bit with lmp_bredr_enabled).
This patch add the new flag and updates the relevant places to test
against it instead of using lmp_bredr_enabled. The flag is by default
enabled when registering an adapter and only cleared if necessary once
the local features have been read during the HCI init procedure.
We cannot completely block BR/EDR usage in case user space uses raw HCI
sockets but the patch tries to block this in places where possible, such
as the various BR/EDR specific ioctls.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds a structure to contain allocation parameters with
the intention of future expansion of this structure. The idea is
that we should be able to add more information about the allocation
in the future in order to allow the allocator to make a better job
of placing the requests on-disk.
There is no functional difference from applying this patch.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Changeset 9e8da9e8 added a parameter to specify the frequency
divisor, used by the driver. However, not all places are passing
this parameter. So, preserve the previous default, to avoid breaking
the existing drivers.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the tuner part of the ds3000 driver was split to share code with the m88rs2000 driver, the ts2020 driver used
the frequency divider value from the m88rs2000 driver. However the ds3000 driver requires a different value, and this
resulted in some frequecies being invisible to the tuner. This patch adds back in the value needed for the ds3000 driver
and configured as an option in the dw2102 frontend driver.
It may also apply to su3000 devices, which use the same ds3000 driver, but for now it is only applied to the s660 device.
Signed-off-by: John Horan <knasher@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Make sure that a format string cannot accidentally
leak into the printk buffer.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
SIZEOF_ARRAY is not used (anymore). Besides, ARRAY_SIZE, defined in
include/linux/kernel.h, should be used rather than explicitly coding some
variant of it.
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reading firmware status register to detect whether firmware is
running or not didn't work 100% reliably. That register was
likely set by firmware itself which means it could not contain
reasonable values until firmware is up and running. Usually it
just worked as some garbage value was returned accidentally but it
appears that in some cases returned garbage value was 0x00 which
was considered "firmware is up and running" by the driver and
firmware loading was skipped leaving device to non-working state.
Fix problem by removing unreliable check and let the driver keep
count whether firmware is loaded or not.
Signed-off-by: Andreas Matthies <a.matthies@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The variable vco_select is only assigned the values true and false.
Change its type to bool.
The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):
@exists@
type T;
identifier b;
@@
- T
+ bool
b = ...;
... when any
b = \(true\|false\)
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Complete() will be run with interrupt enabled, so change to
spin_lock_irqsave().
These functions may be called inside URB->complete(), so use
spin_lock_irqsave().
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ARM architected timers keep counting during suspend so we can
mark this clocksource with the CLOCK_SOURCE_SUSPEND_NONSTOP flag.
This flag will indicate that this clocksource can be used for
calculating suspend time and injecting sleep time into the
timekeeping core. This should be more accurate than using an
external RTC or architecture specific persistent clock.
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
These are all only called by dw_apb_timer_init which is an __init
function, too
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Instead of letting each driver call of_node_put do it centrally in the
loop that also calls the CLOCKSOURCE_OF_DECLARE callbacks. This is less
prone to error and also moves getting and putting the references into the
same function.
Consequently all respective of_node_put calls in drivers are removed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: David Brown <davidb@codeaurora.org>
Zynq is based on an ARM Cortex-A9 MPCore, which features the
arm_global_timer in its SCU. Therefore enable the timer for Zynq.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
On most ARM systems the per-cpu clockevents are truly per-cpu in
the sense that they can't be controlled on any other CPU besides
the CPU that they interrupt. If one of these clockevents were to
become a broadcast source we will run into a lot of trouble
because the broadcast source is enabled on the first CPU to go
into deep idle (if that CPU suffers from FEAT_C3_STOP) and that
could be a different CPU than what the clockevent is interrupting
(or even worse the CPU that the clockevent interrupts could be
offline).
Theoretically it's possible to support per-cpu clockevents as the
broadcast source but so far we haven't needed this and supporting
it is rather complicated. Let's just deny the possibility for now
until this becomes a reality (let's hope it never does!).
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
The arm_global_timer is a per cpu device. Set the appropriate flag.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Add the flag CLOCK_EVT_FEAT_PERCPU which is supposed to be set for per
cpu clockevent devices.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
When RFKill cuts short a scan, mac80211 cancels the scan.
This is done by sending a host command to the firmware, but
this command was dropped because of RFKill. Flag this
command as "SEND_IN_RFKILL" to make sure it is sent to the
firmware. The firmware will send SCAN_COMPLETE_NOTIFICATION
which will trigger a call to ieee80211_scan_completed.
If the scan cannot be aborted, it is because the firmware
already finished the scan but we hadn't notified mac80211
at the time mac80211 decided to cancel the scan. By the time
we see the scan could not be aborted, mac80211 has been
notified already.
This patch fixes situations in which we didn't notify
mac80211 upon completion of the scan that was cut short
by RFkill.
Cc: stable@vger.kernel.org [3.10+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add some new PCI IDs to the table for 6000, 6005 and 6235 series.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This triggers automatic bug reports and add no valuable
information. Print a simple error instead and drop the
host command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add some new PCI IDs to the table for 7000 & 3160 series
Cc: stable@vger.kernel.org
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few NICs can get into trouble if we reset the TX queue
counters in certain very rare situation. To be on the safe
side, simply avoid to reset the TX queue counter.
This is relevant for non-AMPDU queues only since on AMPDU
we have no choice - we must start the TX queue at the right
index.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The D3 firmware image doesn't support uAPSD, so disable it.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Guy Cohen <guy.cohen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the VLAN tci is set in skb->vlan_tci use the
priority field to determine the WMM priority.
Signed-off-by: cedric Voncken <cedric.voncken@acksys.fr>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The remove function implemented for platform driver's remove callback
just return 0 as part of its implementation.
Remove this APIs and do not pass the valid .remove for platform driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
A text file containing calibration data in hex format can
be provided at following path:
/lib/firmware/mrvl/sd8797_caldata.conf
The data will be downloaded to firmware during initialization.
Reviewed-by: Mike Frysinger <vapier@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Hyuckjoo Lee <hyuckjoo.lee@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Replace this proprietary structure with the standard one
(struct hci_command_hdr).
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Command preparation code is used multiple times. This patch
separate out this common code and create btmrvl_send_sync_cmd()
function.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When hci_sock.c calls hci_dev_open it needs to ensure that there isn't
pending work in progress, such as that which is scheduled for the
initial setup procedure or the one for automatically powering off after
the setup procedure. This adds the necessary calls to ensure that any
previously scheduled work is completed before attempting to call
hci_dev_do_open.
This patch fixes a race with old user space versions where we might
receive a HCIDEVUP ioctl before the setup procedure has been completed.
When that happens the setup procedures callback may fail early and leave
the device in an inconsistent state, causing e.g. the setup callback to
be (incorrectly) called more than once.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The requirements of an external call to hci_dev_open from hci_sock.c are
different to that from within hci_core.c. In the former case we want to
flush any pending work in hdev->req_workqueue whereas in the latter we
don't (since there we are already calling from within the workqueue
itself). This patch does the necessary refactoring to a separate
hci_dev_do_open function (analogous to hci_dev_do_close) but does not
yet introduce the synchronizations relating to the workqueue usage.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth protocol and hardware is pretty much all little endian
and so when running sparse via "make C=2" for example, enable the
endian checks by default.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
