Otherwise in some cases, EAPOL frames might be filtered during the
initial handshake, causing delays and assoc failures.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the tid aggregation state has been marked as inactive, free
completed tx packets immediately. When a new aggregation session has not
been initialized yet, the BAW checks do not recognize it as expired.
Might fix potential stalls in setting up a new aggregation session.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Allow ath_tx_get_tid_subframe to return non-AMPDU subframes.
- Reset the tid paused state on aggregation stop
- Initialize software queues even when HT is not supported
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a packet has been tracked as part of the BlockAck window and added
to the hardware queue, it can end up back in the TID queue again with
fi->retries still set to 0 (e.g. if the frame was filtered). Keep an
extra bit for the BAW tracking status to fix this corner case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The check for ATH_AMPDU_SUBFRAME_DEFAULT is unnecessary, since it's set
to half the maximum BlockAck Window size, which is already the maximum
value that h_baw could possibly have. Also remove unnecessary variables.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Improves packet retry order and helps with further tx queueing
improvements.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is essentially the same, but written shorter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00queue_pause_queue_nocheck()is used only in this file.
Fix the following sparse warning:
drivers/net/wireless/rt2x00/rt2x00queue.c:939:6: warning: symbol 'rt2x00queue_pause_queue_nocheck' was not declared. Should it be
static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure that CONFIG_ATH9K_BTCOEX_SUPPORT is used for
the WLAN/BT RX diversity hooks.
Reported by the kernel build testing backend.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Coalesce filters are configured in firmware based on settings
received from cfg80211.
Packet type which is required by firmware is determined based on
provided patterns in a rule:
Unicast: if pattern '01' with offset 0 is found
Multicast: if pattern '33:33' or '01:00:5e' with offset 0 is found
Broadcast: if pattern 'ff:ff:ff:ff' with offset 0 is found
Some example coalesce configuration files:
1) Coalesce Rx data packets from 192.168.0.88
mac address of our device is 00:50:43:21:53:7A
Source IP address offset comes out as 52 after following
calculations:
32 bytes of HW 802.11 header + 8 bytes LLC +
12 bytes in IPV4 header till source IP address
Destination mac is at offset 6 in HW header.
delay=100
condition=1
patterns=01,6+00:50:43:22,10+53:7A,52+c0:a8:00:58
2) Coalesce all broadcast and multicast packets(Multiple packet
types are not allowed in a single rule. Hence created separate
rules)
delay=400
condition=1
patterns=33:33
delay=400
condition=1
patterns=ff:ff:ff:ff
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The offset number is increased to accomodate requests from
user to match more fields in a Rx packet.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is modified so that it can be reused for coalesce feature.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Their names were generic. We need to define similar macros
for coalesce feature. Hence they are renamed here.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull HID fix from Jiri Kosina:
"Revert of a patch which breaks enumeration workaround in
hid-logitech-dj"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
Revert "HID: hid-logitech-dj: querying_devices was never set"
- omapdss: compilation fix and DVI fix for PandaBoard
- mxsfb: fix colors when using 18bit LCD bus
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bHE/
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
- omapdss: compilation fix and DVI fix for PandaBoard
- mxsfb: fix colors when using 18bit LCD bus
* tag 'fbdev-fixes-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
ARM: OMAP: dss-common: fix Panda's DVI DDC channel
video: mxsfb: fix color settings for 18bit data bus and 32bpp
OMAPDSS: analog-tv-connector: compile fix
Pull drm fixes from Dave Airlie:
"Mostly radeon, more fixes for dynamic power management which is is off
by default for this release anyways, but there are a large number of
testers, so I'd like to keep merging the fixes.
Otherwise, radeon UVD fixes affecting suspend/resume regressions, i915
regression fixes, one for your mac mini, ast, mgag200, cirrus ttm fix
and one regression fix in the core"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (25 commits)
drm: Don't pass negative delta to ktime_sub_ns()
drm/radeon: make missing smc ucode non-fatal
drm/radeon/dpm: require rlc for dpm
drm/radeon/cik: use a mutex to properly lock srbm instanced registers
drm/radeon: remove unnecessary unpin
drm/radeon: add more UVD CS checking
drm/radeon: stop sending invalid UVD destroy msg
drm/radeon: only save UVD bo when we have open handles
drm/radeon: always program the MC on startup
drm/radeon: fix audio dto calculation on DCE3+ (v3)
drm/radeon/dpm: disable sclk ss on rv6xx
drm/radeon: fix halting UVD
drm/radeon/dpm: adjust power state properly for UVD on SI
drm/radeon/dpm: fix spread spectrum setup (v2)
drm/radeon/dpm: adjust thermal protection requirements
drm/radeon: select audio dto based on encoder id for DCE3
drm/radeon: properly handle pm on gpu reset
drm/i915: do not disable backlight on vgaswitcheroo switch off
drm/i915: Don't call encoder's get_config unless encoder is active
drm/i915: avoid brightness overflow when doing scale
...
Add support for restart and poweroff functionality present on MSM chipsets
with the MPM2 ps-hold hardware.
Signed-off-by: Abhimanyu Kapur <abhimany@codeaurora.org>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This is a regression introduced by:
commit fe5c3561e6
Author: stephen hemminger <stephen@networkplumber.org>
Date: Sat Jul 13 10:18:18 2013 -0700
vxlan: add necessary locking on device removal
The problem is that vxlan_dellink(), which is called with RTNL lock
held, tries to flush the workqueue synchronously, but apparently
igmp_join and igmp_leave work need to hold RTNL lock too, therefore we
have a soft lockup!
As suggested by Stephen, probably the flush_workqueue can just be
removed and let the normal refcounting work. The workqueue has a
reference to device and socket, therefore the cleanups should work
correctly.
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Tested-by: Cong Wang <amwang@redhat.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a regression introduced by:
commit 3fc2de2fab
Author: stephen hemminger <stephen@networkplumber.org>
Date: Thu Jul 18 08:40:15 2013 -0700
vxlan: fix igmp races
Before this commit, the old code was:
if (vxlan_group_used(vn, vxlan->default_dst.remote_ip))
ip_mc_join_group(sk, &mreq);
else
ip_mc_leave_group(sk, &mreq);
therefore we shoud check vxlan_group_used(), not its opposite,
for igmp_join.
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SmartReflex AVS driver evolved out of the OMAP kernel and now lives
under drivers/power/avs.
I've historically been maintainer of this but Nishanth Menon is doing most
of the heavy lifting now. Add us both as co-maintainers.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Rename mib counter from "low latency" to "busy poll"
v1 also moved the counter to the ip MIB (suggested by Shawn Bohrer)
Eric Dumazet suggested that the current location is better.
So v2 just renames the counter to fit the new naming convention.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the restructuring of the lksctp.org site, we only allow bug
reports through the SCTP mailing list linux-sctp@vger.kernel.org,
not via SF, as SF is only used for web hosting and nothing more.
While at it, also remove the obvious statement that bugs will be
fixed and incooperated into the kernel.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the last module parameter for SCTP and make this
configurable via sysctl for SCTP like all the rest of SCTP's
configuration knobs.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the new procfs knobs:
/proc/sys/net/ipv4/conf/*/igmpv2_unsolicited_report_interval
/proc/sys/net/ipv4/conf/*/igmpv3_unsolicited_report_interval
Which will allow userspace configuration of the IGMP unsolicited report
interval (see below) in milliseconds. The defaults are 10000ms for IGMPv2
and 1000ms for IGMPv3 in accordance with RFC2236 and RFC3376.
Background:
If an IGMP join packet is lost you will not receive data sent to the
multicast group so if no data arrives from that multicast group in a
period of time after the IGMP join a second IGMP join will be sent. The
delay between joins is the "IGMP Unsolicited Report Interval".
Prior to this patch this value was hard coded in the kernel to 10s for
IGMPv2 and 1s for IGMPv3. 10s is unsuitable for some use-cases, such as
IPTV as it can cause channel change to be slow in the presence of packet
loss.
This patch allows the value to be overridden from userspace for both
IGMPv2 and IGMPv3 such that it can be tuned accoding to the network.
Tested with Wireshark and a simple program to join a (non-existent)
multicast group. The distribution of timings for the second join differ
based upon setting the procfs knobs.
igmpvX_unsolicited_report_interval is intended to follow the pattern
established by force_igmp_version, and while a procfs entry has been added
a corresponding sysctl knob has not as it is my understanding that sysctl
is deprecated[1].
[1]: http://lwn.net/Articles/247243/
Signed-off-by: William Manley <william.manley@youview.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The procfs knob /proc/sys/net/ipv4/conf/*/force_igmp_version allows the
IGMP protocol version to use to be explicitly set. As a side effect this
caused the routing cache to be flushed as it was declared as a
DEVINET_SYSCTL_FLUSHING_ENTRY. Flushing is unnecessary and this patch
makes it so flushing does not occur.
Requested by Hannes Frederic Sowa as he was reviewing other patches
adding procfs entries.
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: William Manley <william.manley@youview.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an IGMP join packet is lost you will not receive data sent to the
multicast group so if no data arrives from that multicast group in a
period of time after the IGMP join a second IGMP join will be sent. The
delay between joins is the "IGMP Unsolicited Report Interval".
Previously this value was hard coded to be chosen randomly between 0-10s.
This can be too long for some use-cases, such as IPTV as it can cause
channel change to be slow in the presence of packet loss.
The value 10s has come from IGMPv2 RFC2236, which was reduced to 1s in
IGMPv3 RFC3376. This patch makes the kernel use the 1s value from the
later RFC if we are operating in IGMPv3 mode. IGMPv2 behaviour is
unaffected.
Tested with Wireshark and a simple program to join a (non-existent)
multicast group. The distribution of timings for the second join differ
based upon setting /proc/sys/net/ipv4/conf/eth0/force_igmp_version.
Signed-off-by: William Manley <william.manley@youview.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a misplaced memset(), we never actually enabled the FBC WM on HSW.
Move the memset() to happen a bit earlier, so that it won't clobber
results->enable_fbc_wm.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Introduced in cf3c4c0306
("8139cp: Add dma_mapping_error checking")
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same behavior than 802.1q : finds the encapsulated protocol and
skip 32bit header.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ipgre_header() (header_ops->create) to return the correct
amount of bytes pushed. Most callers of dev_hard_header() seem
to care only if it was success, but af_packet.c uses it as
offset to the skb to copy from userspace only once. In practice
this fixes packet socket sendto()/sendmsg() to gre tunnels.
Regression introduced in c544193214
("GRE: Refactor GRE tunneling code.")
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want the data stored in "addr" and "qual", but the extra ampersands
mean we are copying stack data instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch fixes zd1201 not to use stack as URB transfer_buffer. URB buffers need
to be DMA-able, which stack is not.
Patch is only compile tested.
Cc: stable@vger.kernel.org
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
device_close()->recalc_sigpending() is not needed, sigprocmask() takes
care of TIF_SIGPENDING correctly.
And without ->siglock it is racy and wrong, it can wrongly clear
TIF_SIGPENDING and miss a signal.
But even with this patch device_close() is still buggy:
1. sigprocmask() should not be used, we have set_task_blocked(),
but this is minor.
2. We should never block SIGKILL or SIGSTOP, and this is what
the code tries to do.
3. This can't protect against SIGKILL or SIGSTOP anyway. Another
thread can do signal_wake_up(), say, do_signal_stop() or
complete_signal() or debugger.
4. sigprocmask(SIG_BLOCK, allsigs) doesn't necessarily clears
TIF_SIGPENDING, say, freezing() or ->jobctl.
5. device_write() looks equally wrong by the same reason.
Looks like, this tries to protect some wait_event_interruptible() logic
from signals, it should be turned into uninterruptible wait. Or we need
to implement something like signals_stop/start for such a use-case.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ryan noticed that on his board, HDMI was wired up to port C but not
exposed by the kernel, which had only expected DP on that port. Fix
that up by enumerating both ports if possible.
Tested-by: "Matsumura, Ryan" <ryan.matsumura@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Fix up the whitespace fail. Tsk.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the bitbang core does not require a setup() function we can
drop the check in the altera, nuc900 and xilinx drivers.
Signed-off-by: Mark Brown <broonie@linaro.org>
It's perfectly valid not to have a setup callback when the probe routine
does all the needed things. So don't even check for this case and trust
the caller.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The '!' here was not intended. Since '!' has higher precedence than
compare, it means the check is never true.
This regression was introduced in
commit 71fff20ff1
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Tue Aug 6 22:24:03 2013 +0300
drm/i915: Kill fbc_enable from hsw_lp_wm_results
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ACTIVITY and ERROR signals were reversed in the original commit.
Fix that so that hard drive activity does not show up on the error
light, and attempts to indicate that the hard drive is failing do
not show up as hard drive activity. This fixes a fairly serious
functional bug in the driver, but failing to apply this patch will
not cause any stability issues on the system.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
swiotlb-xen has an implicit dependency on CONFIG_NEED_SG_DMA_LENGTH.
Remove it by replacing dma_length with sg_dma_len.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This patch replace dma_length in "lib/swiotlb.c" to sg_dma_len() macro,
because the build error can occur if CONFIG_NEED_SG_DMA_LENGTH is not
set, and CONFIG_SWIOTLB is set.
Singed-off-by: EunBong Song <eunb.song@samsung.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
