Allow drivers to avoid implementing their own checks for simple rates by
specifying the limits in the master structure.
Signed-off-by: Mark Brown <broonie@linaro.org>
The filter function used by the rspi driver is part of the DMAE controller
driver so if the DMA controller driver is somehow disabled then the rspi
driver will fail to build.
Signed-off-by: Mark Brown <broonie@linaro.org>
New spi controller(version 3) is integrated into Blackfin
60x processor. Comparing to bf5xx spi controller, we support
32 bits word size and independent receive and transmit DMA
channels now. Also mode 0 and 2 (CPHA = 0) can get fully
supported becasue cs line may be controlled by the software.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to make it easier to convert to transfer_one_message() lift the
code that does the actual message transfer out of the work function that
implements the message pump. This should have no functional impact, it's
just a simple code motion patch.
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently no drivers use the ability to override spi_bitbang_transfer()
and if any started this would make it harder to convert the bitbang code
to use transfer_one_message() so remove the export in order to prevent
anyone starting.
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently driver uses local struct s2mps11_info to store ramp rate for bucks
whic its getting through platform data, so instead of using regulator
constraints it should use s2mps11_info to calculate ramp delay.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In function _regulator_do_set_voltage(), old_selector gets intialised only
if (_regulator_is_enabled(rdev) && rdev->desc->ops->set_voltage_time_sel &&
rdev->desc->ops->get_voltage_sel)) is true.
Before calling set_voltage_time_sel() we checks if (old_selector >= 0) and it
will true if it got intialised properly. so we don't need to check again
_regulator_is_enabled(rdev) && rdev->desc->ops->set_voltage_time_sel before
calling set_voltage_time_sel().
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some hardwares support disabling ramp delay, so adding ramp_disable flag to
constraints. It will be used to figure out whether ramp_delay in constraints
is explicitly set to zero or its unintialized (zero by default).
And we don't need to call set_voltage_time_sel() for regulators for whom ramp
delay is disabled in constraints.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix a warning below.
drivers/regulator/lp872x.c:910:33: warning: cast from pointer to integer of
different size [-Wpointer-to-int-cast]
And checkpatch warnings are fixed.
WARNING: space prohibited before semicolon
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Many regulators have several linear ranges of selector with different
step sizes, for example offering better resolution at lower voltages.
Provide regulator_{map,list}_voltage_linear_range() allowing these
regulators to use generic code. To do so a table of regulator_linear_range
structs needs to be pointed to from the descriptor.
This was inspired by similar code included in a driver submission from
Chao Xie and Yi Zhang at Marvell.
Signed-off-by: Mark Brown <broonie@linaro.org>
The expected semantic for something expressed as a tolerance is that it
should deliver the specified value with some deviation allowed but this
is not what set_voltage_tol() currently does. Instead it just passes
the maximum possible range to set_voltage() which will typically result
in a voltage aimed at lower than the target voltage.
Instead first try to set a voltage between the target voltage and the
upper limit, then fall back on the full range. This will be much more
robust against physical variation in systems and makes the API behave
more like users would expect.
Signed-off-by: Mark Brown <broonie@linaro.org>
sgtl5000 has 16-bit registers, and only even numbers are valid for its registers
addresses.
Let regmap knows about this feature by specifying the 'reg_stride' field, so
that it can access only the valid registers.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As well as being better style this allows the device to idle when there is
no audio card instantaited which is probably what we want.
Signed-off-by: Mark Brown <broonie@linaro.org>
Add missing .owner of struct snd_soc_card. This prevents the
module from being removed from underneath its users.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add missing .owner of struct snd_soc_card. This prevents the
module from being removed from underneath its users.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add missing .owner of struct snd_soc_card. This prevents the
module from being removed from underneath its users.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is better from a device model point of view since we don't try to
do things like instantiate the card until the required resources appear.
Signed-off-by: Mark Brown <broonie@linaro.org>
The version number has never been updated and the printk isn't based on
any interaction with the device.
Signed-off-by: Mark Brown <broonie@linaro.org>
The code enabled SSIEN when triggered by SNDRV_PCM_TRIGGER_START,
so move the disable code to SNDRV_PCM_TRIGGER_STOP for symmetric.
This also allows us to use the SSI driver more flexible so that
it can support some use cases like "aplay S16_LE.wav S24_LE.wav"
which would call the driver in sequence like:
startup()->hw_params(S16_LE)->trigger(START)->tirgger(STOP)->
hw_params(S24_LE)->trigger(START)->tirgger(STOP)->shutdown()
If we disable SSIEN in shutdown(), the second hw_params() would
bypass the sample bits setting while using symmetric_rate.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
fsl-ssi was located in powerpc/fsl/ssi.txt. This is no powerpc specific
device, so it should be moved to sound/ as it connects to differen audio
codecs.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cleaner parameter passing for imx-pcm-fiq. Create a seperated fiq-params
struct to pass all arguments.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch removes the NO_DT flag. The pdev pointer may have a proper
of_node with the dmas property, so we can use it to request DMA
channels.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add missing .owner of struct snd_soc_card. This prevents the
module from being removed from underneath its users.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
The main function of the option is to enable compile testing. There is
still an option since COMPILE_TEST is intended to enable selection of
extra drivers rather than forcing them on.
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing .owner of struct snd_soc_card. This prevents the
module from being removed from underneath its users.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
While the conversion of BKL to mutex in commit 645ef9ef, the mutex
definition was put in a wrong place inside #ifdef WSND_DEBUG, which
leads to the build error. Just move it outside the ifdef.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Align atmel pcm to use ASoC generic dmaengine framework
DMA is fully device tree based
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
as the phybase paramter only used for DMA operation, change
it's type from resource_size_t to dma_addr_t
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
as prepare callback for dma is acctually access ssc register
which better done in dai driver, so move it to dai prepare
callback function
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
add error mask define, which will be used when execute DMA transfer
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
move set dma data to startup callback function, if the set dma
data exist in hw_params callback, so the dma data only usable when
call hw_params, if want use it before hw_params callback, it will
cause NULL pointer access oops
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When doing signal activity detection, the only output from the DRC will
often be a GPIO pin. This patch adds a signal activity output that is
activated when a GPIO is configured to output the DRC signal activity
detection.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Correction of the omap_usb3_dpll_params array when the sys_clk_rate is
20MHz.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
