Without the new LLCP_CONNECTING state, non blocking sockets will be
woken up with a POLLHUP right after calling connect() because their
state is stuck at LLCP_CLOSED.
That prevents userspace from implementing any proper non blocking
socket based NFC p2p client.
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver declares two virtual NFC devices supporting NFC-DEP protocol.
An LLCP connection can be established between them and all packets sent
from one device is sent back to the other, acting as loopback devices.
Once established, the LLCP link can be disconnected by disabling the target
device (with rfkill, nfctool, or neard disable-adapter test script).
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In nfc_llcp_tx_work() the sk_buff is not freed when the llcp_sock
is null and the PDU is an I one.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch keeps the socket alive and therefore does not remove
it from the sockets list in the local until the DISC PDU has been
actually sent. Otherwise we would reply with DM PDUs before sending
the DISC one.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
nfc_llcp_send_disconnect() already exists but is not used.
nfc_llcp_disconnect() naming is not consistent with other PDU
sending functions.
This patch removes nfc_llcp_send_disconnect() and renames
nfc_llcp_disconnect()
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Instead of dumping ACR122 frames as errors, we use the print_hex_dump()
dynamic debug APIs.
We also print an accurate IC version, as the ACR122 is pn532 based.
Signed-off-by: Olivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Enabling or disabling an NFC accessible secure element through netlink
requires giving both an NFC controller and a secure element indexes.
Once enabled the secure element will handle card emulation once polling
starts.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Called via netlink, this API will enable or disable a specific secure
element. When a secure element is enabled, it will handle card emulation
and more generically ISO-DEP target mode, i.e. all target mode cases
except for p2p target mode.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When an NFC driver or host controller stack discovers a secure element,
it will call nfc_add_se(). In order for userspace applications to use
these secure elements, a netlink event will then be sent with the SE
index and its type. With that information userspace applications can
decide wether or not to enable SEs, through their indexes.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This API will allow NFC drivers to add and remove the secure elements
they know about or detect. Typically this should be called (asynchronously
or not) from the driver or the host interface stack detect_se hook.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Secure elements need to be discovered after enabling the NFC controller.
This is typically done by the NCI core and the HCI drivers (HCI does not
specify how to discover SEs, it is left to the specific drivers).
Also, the SE enable/disable API explicitely takes a SE index as its
argument.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Supported secure elements are typically found during a discovery process
initiated when the NFC controller is up and running. For a given NFC
chipset there can be many configurations (embedded SE or not, with or
without a SIM card wired to the NFC controller SWP interface, etc...) and
thus driver code will never know before hand which SEs are available.
So we remove this field, it will be replaced by a real SE discovery
mechanism.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When using NFC-F we should copy the NFCID2 buffer that we got from
SENSF_RES through the ATR_REQ NFCID3 buffer. Not doing so violates
NFC Forum digital requirement #189.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Before any operation, driver interruption is de-asserted to prevent
race condition between TX and RX.
Transaction starts by emitting "Direct read" and acknowledged mode
bytes. Then packet length is read allowing to allocate correct NCI
socket buffer. After that payload is retrieved.
A delay after the transaction can be added.
This delay is determined by the driver during nci_spi_allocate_device()
call and can be 0.
If acknowledged mode is set:
- CRC of header and payload is checked
- if frame reception fails (CRC error): NACK is sent
- if received frame has ACK or NACK flag: unblock nci_spi_send()
Payload is passed to NCI module.
At the end, driver interruption is re asserted.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Before any operation, driver interruption is de-asserted to prevent
race condition between TX and RX.
The NCI over SPI header is added in front of NCI packet.
If acknowledged mode is set, CRC-16-CCITT is added to the packet.
Then the packet is forwarded to SPI module to be sent.
A delay after the transaction is added.
This delay is determined by the driver during nci_spi_allocate_device()
call and can be 0.
After data has been sent, driver interruption is re-asserted.
If acknowledged mode is set, nci_spi_send will block until
acknowledgment is received.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The NFC Forum defines a transport interface based on
Serial Peripheral Interface (SPI) for the NFC Controller
Interface (NCI).
This module implements the SPI transport of NCI, calling SPI module
directly to read/write data to NFC controller (NFCC).
NFCC driver should provide functions performing device open and close.
It should also provide functions asserting/de-asserting interruption
to prevent TX/RX race conditions.
NFCC driver can also fix a delay between transactions if needed by
the hardware.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This part of bias settings are essential for WM8962 to power up. Without it
"wm8962 0-001a: DC servo timed out" might be prompted due to power-up failure
that happens to FLL if being used.
The driver's also bringing the bias down in the suspend path so it needs to be
powered up in the resume path for symmetry.
According to dapm_pre_sequence_async(), DAPM would call pm_runtime_get_sync()
to let driver finish the bias settings in pm_runtime_resume() before the bias
level being set to STANDBY. So no need to worry about disordered settings for
VMID of WM8962.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The power up/down sequence order for DAPM switch widgets is not explicitly
initialized, causing them to be run always as the first widget type for both
power up and down. Move it to the same position in the sequence as other mixer
widget types.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 85762e71 ("ASoC: dapm: Implement mixer control sharing") the
long_name field of the snd_soc_dapm_path struct is unused. All of the name
handling now happens entirely in dapm_create_or_share_mixmux_kcontrol(). So we
can remove the long_name field from the snd_soc_dapm_path struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have the same code for freeing a DAPM path in three different locations.
Introduce a new helper function to take care of this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The condition 'i == item' is only true when, well, 'i' equals 'item'.
So just use 'item' directly as the index into the array.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The private data containing the widget list that is a assigned to a DAPM
kcontrol is never freed. Setup the private_free for DAPM kcontrols to take care
of this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The individual component drivers are only useful with a machine driver and
should be selected by the machine drivers so shouldn't have help text of
their own in order to hide them in interactive configuration.
Signed-off-by: Mark Brown <broonie@linaro.org>
I've restricted atomic_open to only operate on regular files, although
I still don't understand why atomic_open should not be possible also for
directories on GFS2. That can always be added in later though, if it
makes sense.
The ->atomic_open function can be passed negative dentries, which
in most cases means either ENOENT (->lookup) or a call to d_instantiate
(->create). In the GFS2 case though, we need to actually perform the
look up, since we do not know whether there has been a new inode created
on another node. The look up calls d_splice_alias which then tries to
rehash the dentry - so the solution here is to simply check for that
in d_splice_alias. The same issue is likely to affect any other cluster
filesystem implementing ->atomic_open
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "J. Bruce Fields" <bfields fieldses org>
Cc: Jeff Layton <jlayton@redhat.com>
In struct snd_soc_card zylonite .owner is assigned THIS_MODULE
twice, remove one of them.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This typedef is unnecessary and should just be removed.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Also fix return values for headphone switch updates.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Bring Transparent HugePage support to ARM. The size of a
transparent huge page depends on the normal page size. A
transparent huge page is always represented as a pmd.
If PAGE_SIZE is 4KB, THPs are 2MB.
If PAGE_SIZE is 64KB, THPs are 512MB.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
The buddy allocator has a default MAX_ORDER of 11, which is too
low to allocate enough memory for 512MB Transparent HugePages if
our base page size is 64KB.
This patch introduces MAX_ZONE_ORDER and sets it to 14 when 64KB
pages are used in conjuction with THP, otherwise the default value
of 11 is used.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Add huge page support to ARM64, different huge page sizes are
supported depending on the size of normal pages:
PAGE_SIZE is 4KB:
2MB - (pmds) these can be allocated at any time.
1024MB - (puds) usually allocated on bootup with the command line
with something like: hugepagesz=1G hugepages=6
PAGE_SIZE is 64KB:
512MB - (pmds) usually allocated on bootup via command line.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Under ARM64, PTEs can be broadly categorised as follows:
- Present and valid: Bit #0 is set. The PTE is valid and memory
access to the region may fault.
- Present and invalid: Bit #0 is clear and bit #1 is set.
Represents present memory with PROT_NONE protection. The PTE
is an invalid entry, and the user fault handler will raise a
SIGSEGV.
- Not present (file or swap): Bits #0 and #1 are clear.
Memory represented has been paged out. The PTE is an invalid
entry, and the fault handler will try and re-populate the
memory where necessary.
Huge PTEs are block descriptors that have bit #1 clear. If we wish
to represent PROT_NONE huge PTEs we then run into a problem as
there is no way to distinguish between regular and huge PTEs if we
set bit #1.
To resolve this ambiguity this patch moves PTE_PROT_NONE from
bit #1 to bit #2 and moves PTE_FILE from bit #2 to bit #3. The
number of swap/file bits is reduced by 1 as a consequence, leaving
60 bits for file and swap entries.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
If we consider the following code sequence:
my_pte = pte_modify(entry, myprot);
x = pte_write(my_pte);
y = pte_exec(my_pte);
If myprot comes from a PROT_NONE page, then x and y will both be
true which is undesireable behaviour.
This patch sets the no-execute and read-only bits for PAGE_NONE
such that the code above will return false for both x and y.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
In paging_init the memblock limit is set to restrict any addresses
returned by early_alloc to fit within the initial direct kernel
mapping in swapper_pg_dir. This allows map_mem to allocate puds,
pmds and ptes from the initial direct kernel mapping.
The limit stays low after paging_init() though, meaning any
bootmem allocations will be from a restricted subset of memory.
Gigabyte huge pages, for instance, are normally allocated from
bootmem as their order (18) is too large for the default buddy
allocator (MAX_ORDER = 11).
This patch restores the memblock limit when map_mem has finished,
allowing gigabyte huge pages (and other objects) to be allocated
from all of bootmem.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
All Transparent Huge Pages are allocated by the buddy allocator.
A compile time check is in place that fails when the order of a
transparent huge page is too large to be allocated by the buddy
allocator. Unfortunately that compile time check passes when:
HPAGE_PMD_ORDER == MAX_ORDER
( which is incorrect as the buddy allocator can only allocate
memory of order strictly less than MAX_ORDER. )
This patch updates the compile time check to fail in the above
case.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
huge_pte_alloc, huge_pte_offset and follow_huge_p[mu]d have
already been copied over to mm.
This patch removes the x86 copies of these functions and activates
the general ones by enabling:
CONFIG_ARCH_WANT_GENERAL_HUGETLB
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
The huge_pte_alloc, huge_pte_offset and follow_huge_p[mu]d
functions in x86/mm/hugetlbpage.c do not rely on any architecture
specific knowledge other than the fact that pmds and puds can be
treated as huge ptes.
To allow other architectures to use this code (and reduce the need
for code duplication), this patch copies these functions into mm,
replaces the use of pud_large with pud_huge and provides a config
flag to activate them:
CONFIG_ARCH_WANT_GENERAL_HUGETLB
If CONFIG_ARCH_WANT_HUGE_PMD_SHARE is also active then the
huge_pmd_share code will be called by huge_pte_alloc (othewise we
call pmd_alloc and skip the sharing code).
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
The huge_pmd_share code has been copied over to mm/hugetlb.c to
make it accessible to other architectures.
Remove the x86 copy of the huge_pmd_share code and enable the
ARCH_WANT_HUGE_PMD_SHARE config flag. That way we reference the
general one.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Under x86, multiple puds can be made to reference the same bank of
huge pmds provided that they represent a full PUD_SIZE of shared
huge memory that is aligned to a PUD_SIZE boundary.
The code to share pmds does not require any architecture specific
knowledge other than the fact that pmds can be indexed, thus can
be beneficial to some other architectures.
This patch copies the huge pmd sharing (and unsharing) logic from
x86/ to mm/ and introduces a new config option to activate it:
CONFIG_ARCH_WANTS_HUGE_PMD_SHARE
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
This typedef is unnecessary and should just be removed.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Robin Holt <holt@sgi.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Suppose an initiator sends a DATA IN command with an allocation length
shorter than the FC transfer length -- we get a target message like
TARGET_CORE[qla2xxx]: Expected Transfer Length: 256 does not match SCSI CDB Length: 0 for SAM Opcode: 0x12
In that case, the target core adjusts the data_length and sets
se_cmd->residual_count for the underrun. But now suppose that command
fails and we end up in tcm_qla2xxx_queue_status() -- that function
unconditionally overwrites residual_count with the already adjusted
data_length, and the initiator will burp with a message like
qla2xxx [0000:00:06.0]-301d:0: Dropped frame(s) detected (0x100 of 0x100 bytes).
Fix this by adding on to the existing underflow residual count instead.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Here is a fun one. Bug seems to have been introduced by commit 140854cb,
almost two years ago. I have no idea why we only started seeing it now,
but we did.
Rough callgraph:
core_tpg_set_initiator_node_queue_depth()
`-> spin_lock_irqsave(&tpg->session_lock, flags);
`-> lio_tpg_shutdown_session()
`-> iscsit_stop_time2retain_timer()
`-> spin_unlock_bh(&se_tpg->session_lock);
`-> spin_lock_bh(&se_tpg->session_lock);
`-> spin_unlock_irqrestore(&tpg->session_lock, flags);
core_tpg_set_initiator_node_queue_depth() used to call spin_lock_bh(),
but 140854cb changed that to spin_lock_irqsave(). However,
lio_tpg_shutdown_session() still claims to be called with spin_lock_bh()
held, as does iscsit_stop_time2retain_timer():
* Called with spin_lock_bh(&struct se_portal_group->session_lock) held
Stale documentation is mostly annoying, but in this case the dropping
the lock with the _bh variant is plain wrong. It is also wrong to drop
locks two functions below the lock-holder, but I will ignore that bit
for now.
After some more locking and unlocking we eventually hit this backtrace:
------------[ cut here ]------------
WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0xe8/0x100()
Pid: 24645, comm: lio_helper.py Tainted: G O 3.6.11+
Call Trace:
[<ffffffff8103e5ff>] warn_slowpath_common+0x7f/0xc0
[<ffffffffa040ae37>] ? iscsit_inc_conn_usage_count+0x37/0x50 [iscsi_target_mod]
[<ffffffff8103e65a>] warn_slowpath_null+0x1a/0x20
[<ffffffff810472f8>] local_bh_enable_ip+0xe8/0x100
[<ffffffff815b8365>] _raw_spin_unlock_bh+0x15/0x20
[<ffffffffa040ae37>] iscsit_inc_conn_usage_count+0x37/0x50 [iscsi_target_mod]
[<ffffffffa041149a>] iscsit_stop_session+0xfa/0x1c0 [iscsi_target_mod]
[<ffffffffa0417fab>] lio_tpg_shutdown_session+0x7b/0x90 [iscsi_target_mod]
[<ffffffffa033ede4>] core_tpg_set_initiator_node_queue_depth+0xe4/0x290 [target_core_mod]
[<ffffffffa0409032>] iscsit_tpg_set_initiator_node_queue_depth+0x12/0x20 [iscsi_target_mod]
[<ffffffffa0415c29>] lio_target_nacl_store_cmdsn_depth+0xa9/0x180 [iscsi_target_mod]
[<ffffffffa0331b49>] target_fabric_nacl_base_attr_store+0x39/0x40 [target_core_mod]
[<ffffffff811b857d>] configfs_write_file+0xbd/0x120
[<ffffffff81148f36>] vfs_write+0xc6/0x180
[<ffffffff81149251>] sys_write+0x51/0x90
[<ffffffff815c0969>] system_call_fastpath+0x16/0x1b
---[ end trace 3747632b9b164652 ]---
As a pure band-aid, this patch drops the _bh.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nobody should be expecting to read or write virtual_lun0.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use bool params when appropriate.
Eliminate unneeded pr_reg_e and type variables.
Just one goto label, so rename to 'out' from 'out_put_pr_reg'.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Don't need goto, we can just do an if/else for sa_res_key behavior. Move
shorter case first. Slightly shorter b/c both cases can share a call to
update_and_write_aptpl() now.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
