Fix placement of braces in structs and unions.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver supports a number of simple digital i/o boards with
slight variations in the register map. Clean up the comment about
the register map to better document the driver.
Remove the #define's used for the registers since thet don't apply
to all the board variations supported by the driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ICP P8R8-DIO ISA boards can be supported by this driver. This board
has 8 isolated digital outputs and 8 isolated digital outputs.
Add support for this board to the pcl730 driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ACL-7225b and P16R16R-DIO ISA boards can be supported by this driver.
These board have 16 isolated digital outputs and 16 isolated digital
outputs.
Add support for these boards to the pcl730 driver and remove the
standalone acl7225b driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PCL-734 ISA board can be supported by this driver. This board has
32 isolated digital outputs.
Add support for the PCL-734 board to the pcl730 driver and remove it
from the poc driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PCL-733 ISA board can be supported by this driver. This board has
32 isolated digital inputs.
Add support for the PCL-733 board to the pcl730 driver and remove it
from the poc driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PCL-725 ISA board can be supported by this driver. This board has
8 isolated digital inputs and 8 isolated digital outputs.
Add support for the PCL-725 board to the pcl730 driver and remove the
standalone pcl725 driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PCM-3730 PC/104 board has the same register i/o map as the PCL-730
ISA board. The only difference is the number of isolated digital input
and output channels.
Add support for the PCM-3770 board to the pcl730 driver and remove the
standalone pcm3730 driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
X-Patchwork-Delegate: mchehab@redhat.com
There are a few cases where breaking the code into separate
lines make it worse to read. However, on several places,
breaking it to make checkpatch.pl happier is OK and improves
code readability.
So, break longer lines where that won't cause harm.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
There are several places where: state->var = (some_var)
The parenthesis there are doing nothing but making it
harder to read and breaking the 80 columns soft limits.
Just get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
Almost all 80-col warnings are related to comments. There's
one, however, that it is due to a one-line enum declaration
for enum agc_ctrl_mode.
Break it into one line per enumered data.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
The comments markup language used on Kernel is defined at:
Documentation/kernel-doc-nano-HOWTO.txt
Remove invalid markups from the header file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
Fixes the following checkpatch.pl warnings:
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(10);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
replace all occurrences of printk(KERN_* by
pr_info/pr_warn/pr_err/pr_debug/pr_cont macros.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
Thare are lots of CamelCase warnings produced by checkpatch.pl.
This weren't fixed at the time the driver got submitted due
to the lack of manpower do to such cleanup.
Now that I have one script that automates this task, cleans
it. That makes the driver almost checkpatch-compliant,
except for 80 column warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
Log10 routine is already defined at dvb_math.h and provides a good
enough approximation for 100 x log10(). So, instead of reinventing
the wheel, use the already existing function.
While here, don't use CamelCase on the function name.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The device has been tested on a MIPSel box with kernel 3.1.1 and backported media_tree drivers
The kernel detects the device with the following output:
usbcore: registered new interface driver dvb_usb_rtl28xxu
usb 1-2: dvb_usb_v2: found a 'Crypto Redi PC50A' in warm state
usb 1-2: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Crypto Redi PC50A)
usb 1-2: DVB: registering adapter 1 frontend 0 (Realtek RTL2832 (DVB-T))...
i2c i2c-4: fc0012: Fitipower FC0012 successfully identified
usb 1-2: dvb_usb_v2: 'Crypto Redi PC50A' successfully initialized and connected
[crope@iki.fi: fix trivial merge conflict]
Signed-off-by: Alessandro Miceli <angelofsky1980@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
USB ID 0413:6a03 is Leadtek WinFast DTV Dongle mini.
Decoder Realtek RTL2832U and tuner Infineon TUA9001.
Signed-off-by: Miroslav Šustek <sustmidown@centrum.cz>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi,
This patch uses the driver from openpli[1] as a template to restore the remote control support.
I had to divert from the original to use the in kernel rc protocol decoder. The key repetition does,
not seem to work but I cant find the problem in the driver. As a raw rc provider, no key table is
hardcoded.
Rodrigo.
[1]: https://aur.archlinux.org/packages/dvb-usb-rtl2832u-openpli/?comments=all
Signed-off-by: Rodrigo Tartajo <rtarty@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
in soc_camera_close(), if ici->ops->remove() removes device firstly,
and then call __soc_camera_power_off(), it has logic error. Since
if remove device, it should disable subdev clk. but in __soc_camera_
power_off(), it will callback v4l2 s_power function which will
read/write subdev registers to control power by i2c. and then
i2c read/write will fail because of clk disable.
So suggest to re-sequence two functions call.
Change-Id: Iee7a6d4fc7c7c1addb5d342621eb8dcd00fa2745
Signed-off-by: Wenbing Wang <wangwb@marvell.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'bytesperline' value only indicates the stride of the Y plane
if the color format is planar, such as NV12. When calculating
the total plane size, the size of CbCr plane must also be considered.
Signed-off-by: Katsuya Matsubara <matsu@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the sh_veu driver, only the interrupt handler 'sh_veu_bh'
can invoke the v4l2_m2m_job_finish() function.
So the hardware must be alive for handling interrupts
until returning from v4l2_m2m_ctx_release().
Signed-off-by: Katsuya Matsubara <matsu@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_m2m_job_finish() should be invoked even if the current
ongoing job has been aborted since v4l2_m2m_ctx_release() which
has issued the job abort may wait until the finish function is invoked.
Signed-off-by: Katsuya Matsubara <matsu@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Function media_entity_remote_source actually returns the remote pad to
the given one, regardless if this is the source or the sink pad.
Name media_entity_remote_pad is more adequate for this function.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The clips pointer is a userspace pointer, not a kernelspace pointer,
so you can't dereference the clips pointer.
Also add a few missing commas and newlines.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The radio filter function that filters controls that are valid for a radio
device should also accept V4L2_CTRL_CLASS_FM_RX controls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes a NULL pointer deference when loading the cx88_dvb module for a
Hauppauge HVR4000.
The bugzilla bug report is here:
https://bugzilla.kernel.org/show_bug.cgi?id=56271
The cause is that the wm8775 is optional, so even though the board info says
there is one, it doesn't have to be there. Checking whether the module was
actually loaded is much safer.
Note that this driver is quite buggy when it comes to unloading and reloading
modules. Unloading cx8800 and reloading it again will still cause a crash,
most likely because either the i2c bus isn't unloaded at the right time and/or
the v4l2_device_unregister isn't called at the right time.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Sebastian Frei <sebastian@familie-frei.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The version number was still 3.9: update to 3.10.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested on a MIPSel box with 3.3.6 kernel
The kernel output when the device will be detected follows:
usbcore: registered new interface driver dvb_usb_it913x
it913x: Chip Version=01 Chip Type=9135
it913x: Remote propriety (raw) mode
it913x: Dual mode=3 Tuner Type=38
it913x: Chip Version=01 Chip Type=9135
usb 2-1: dvb_usb_v2: found a 'Digital Dual TV Receiver CTVDIGDUAL_V2' in cold state
usb 2-1: dvb_usb_v2: downloading firmware from file 'dvb-usb-it9137-01.fw'
it913x: FRM Starting Firmware Download
it913x: FRM Firmware Download Completed - Resetting Device
it913x: Chip Version=01 Chip Type=9135
it913x: Firmware Version 204147968
usb 2-1: dvb_usb_v2: found a 'Digital Dual TV Receiver CTVDIGDUAL_V2' in warm state
usb 2-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Digital Dual TV Receiver CTVDIGDUAL_V2)
it913x-fe: ADF table value :00
it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 00
it913x-fe: Tuner LNA type :38
usb 2-1: DVB: registering adapter 1 frontend 0 (Digital Dual TV Receiver CTVDIGDUAL_V2_1)...
usb 2-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Digital Dual TV Receiver CTVDIGDUAL_V2)
it913x-fe: ADF table value :00
it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 00
it913x-fe: Tuner LNA type :38
usb 2-1: DVB: registering adapter 2 frontend 0 (Digital Dual TV Receiver CTVDIGDUAL_V2_2)...
usb 2-1: dvb_usb_v2: 'Digital Dual TV Receiver CTVDIGDUAL_V2' successfully initialized and connected
RC part not tested
Signed-off-by: Alessandro Miceli <angelofsky1980@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For consistency, it is necessary to use the autodetected inversion
instead of the configured one.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In non S2 mode, the device is able to autodetect inversion. So
let's store it for tuning to S2 transponders.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
