Following patch will fix build error if CONFIG_DMA_ENGINE is unset.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ath_complete_reset will not be called if ath9k_hw_reset
is unsuccessful, so we need to re-enable intertupts to
balence the previous ath_prepare_reset call. Also schedule a
reset as a best effort method to recover the chip from
whatever state caused the channel change failure.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=55771
Signed-off-by: Robert Shade <robert.shade@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nvram contains critical initialization parameter for firmware to run. Host
driver should not proceed if nvram fails to be downloaded to dongle.
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When multiple cipher suites have been programmed then the lowest
suite is to be retured. This fixes issue when AP mode is using
CCMP and TKIP WPA combination where rekeying will fail.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
on stop_ap the dongle was not properly shutdown. As a result it was
not possible to restart AP or STA after AP operation without
restarting the device. This patch will fix that.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx and rx michael tkip keys are always swapped in case being
configured per mac. This is wrong for AP. The swap should only
be done for STA mode.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are waiting on first scan command of internal scan request
before association, so we should complete on last internal scan
command response.
Cc: <stable@vger.kernel.org> # 3.8
Tested-by: Daniel Drake <dsd@laptop.org>
Tested-by: Marco Cesarano <marco@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a bunch of different things in this series, I can split them out
if need be:
- Support for configuring the button detection circuit to reflect the
accessories supplied with the system.
- Improvements in the HPDET based detection scheme.
- Additional robustness against more pathological use cases.
- A few small standalone fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=6SXJ
-----END PGP SIGNATURE-----
Merge tag 'extcon-arizona-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into char-misc-next
Mark writes:
extcon: arizona: Updates for v3.10
There's a bunch of different things in this series, I can split them out
if need be:
- Support for configuring the button detection circuit to reflect the
accessories supplied with the system.
- Improvements in the HPDET based detection scheme.
- Additional robustness against more pathological use cases.
- A few small standalone fixes.
Commit "cs5535-mfgpt: Add another reset method" introduced an unterminated
string and broke the build.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
merge window. Fortunately, Cai and Christian noticed before 3.9
shipped.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=n1ir
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Unfortunately, we introduced some big-endian bugs during the last
merge window. Fortunately, Cai and Christian noticed before 3.9
shipped."
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix big-endian bugs which could cause fs corruptions
Ratelimited printk will be useful in printing xfs messages which are otherwise
not required to be printed always due to their high rate (to prevent kernel ring
buffer from overflowing), while at the same time required to be printed.
Signed-off-by: Raghavendra D Prabhu <rprabhu@wnohang.net>
Reviewed-by: Rich Johnston <rjohnston@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
commit eca4549f57 "sysfs: Add crash_notes_size to export percpu
note size" adds a printk that outputs a size_t value as %lu
when it should be %zu, resulting in this warning.
drivers/base/cpu.c: In function 'show_crash_notes_size':
drivers/base/cpu.c:142:2: warning: format '%lu' expects argument of type 'long unsigned int', but argument 3 has type 'unsigned int' [-Wformat=]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The inode->i_mutex isn't hold when updating filp->f_pos
in read()/write(), so the filp->f_pos might be read as
0 or 1 in readdir() when there is concurrent read()/write()
on this same file, then may cause use after free in readdir().
The bug can be reproduced with Li Zefan's test code on the
link:
https://patchwork.kernel.org/patch/2160771/
This patch fixes the use after free under this situation.
Cc: stable <stable@vger.kernel.org>
Reported-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for parsing of the DT display-timings prop
to IPU KMS driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
recent changes to gadget framework have
exposed a flaw in nokia.c where it uses
f_ecm.c but it wasn't including it like
other gadget drivers.
This is a temporary patch until all other
function drivers are converted to new API
where each function driver becomes a module
and binding is done through configfs.
Solves a linking error when building g_nokia.ko
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull reiserfs fix from Jan Kara:
"A fix for reiserfs xattr bug exposed by changes to lookup_one_len()"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
reiserfs: Fix warning and inode leak when deleting inode with xattrs
Pull s390 fixes from Martin Schwidefsky:
"Just a bunch of bugfixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: provide emtpy check_pgt_cache() function
s390/uaccess: fix page table walk
s390/3270: fix minor_start issue
s390/uaccess: fix clear_user_pt()
s390/scm_blk: fix error return code in scm_blk_init()
s390/scm_block: fix printk format string
drivers/Kconfig: add several missing GENERIC_HARDIRQS dependencies
For fixed voltage, we can just set min_uV and use regulator_list_voltage_linear
for list_voltage callback. Regulator core will call list_voltage(rdev, 0) if
both get_voltage get_voltage_sel are not implemented. Thus we can also remove
lp8788_ldo_fixed_get_voltage() function.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The id for DLDOx matches the entries in enum lp8788_ldo_id and it's easy to
calculate the id for ALDOx. Thus remove lp8788_dldo_id and lp8788_aldo_id
arrays.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is required for regulator_list_voltage_table() to properly work.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
commit b080c78a4e
"regulator: ab8500: Update voltage handling for fixed voltage regulators"
removes min_uV settings and sets volt_table for all fixed voltages, thus
we can not use regulator_list_voltage_linear now. Use
regulator_list_voltage_table instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Quite a few changes in this patch, including: supply-name changes, new
consumers, initialisation and capability updates and new regulators.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ab*_match[] arrays should be moved out of the way, instead of
bunched in the middle of the initialisation functions. This patch
moves all initialisation code which currently resides above these
arrays down to be grouped with the others. This makes the whole
thing slightly easier to read.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Regulator platform data is now passed though a single structure
as opposed to the old way where four separate struct elements
were required. This patch makes use of the new format.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The regulator framework offers a generic regulator_list_voltage_table()
function which can directly look-up a regulator's voltage capabilities
using a table provided through the desc structure. This patch ensures
that information is available.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The regulator framework now has provisions to read a regulator's
start-up time via the 'enable_time' attribute. So let's remove all
'enable_time'/'delay' duplication and just stick with 'enable_time'
from now on.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow the regulator framework to directly access the time it takes
any given regulator to settle. This saves time and code because
without it we would have to implement a dedication function to read
the value from elsewhere.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce aux5, aux6 into ab8540 regulator framework.
Signed-off-by: Zhenhua HUANG <zhenhua.huang@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Maxime COQUELIN <maxime.coquelin@stericsson.com>
Reviewed-by: David PARIS <david.paris@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
At the probe use a structure to select the good regulator array from
from ab9540, ab8505, ab8540 or ab8500 configuration.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rename SEGMENT_SIZE and SEGMENT_SHIFT as the former is used in a.out.h.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: linux-usb@vger.kernel.org
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Use ilog2() rather than __ffs() for calculating SEGMENT_SHIFT as ilog2() can
be worked out at compile time, whereas __ffs() must be calculated at runtime.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: linux-usb@vger.kernel.org
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Merge branch 'fix/samsung' of
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into
asoc-component to resolve trivial conflict
Conflicts:
sound/soc/samsung/i2s.c
This adds a simple device tree binding for db8540 boards.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@stericsson.com>
Reviewed-by: Philippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the common DAI DMA data struct for tegra, this allows us to use the common
helper function to configure the DMA slave config based on the DAI DMA data.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the common DAI DMA data struct for omap, this allows us to use the common
helper function to configure the DMA slave config based on the DAI DMA data.
For omap-dmic and omap-mcpdm also move the DMA data from a global variable to
the driver state struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a common DMA data struct which can be used by DAI drivers to
communicate their DMA configuration requirements to the DMA pcm driver. Having
a common data structure for this allows us to implement common functions on top
of them, which can be used by multiple platforms.
This patch also introduces a new function to initialize certain fields of a
dma_slave_config struct from the common DAI DMA data struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Usually device_fc should be set to false for audio DMAs. Initialize it in a
common place so drivers don't have to do this manually.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The tegra dmaengine driver does not support pausing and resuming a DMA stream.
The tegra PCM driver still claims to support pause and resume though and
implements them by stopping and restarting the stream. This is not what an
application using pause/resume would expect. Usually applications have support
for working around PCMs which do not support suspend and resume, so don't set
the SNDRV_PCM_INFO_PAUSE and SNDRV_PCM_INFO_RESUME flags for the tegra PCM and
use the default snd_dmaengine_pcm_trigger callback.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Just for cleaning up, introduce a new function get_sample_rate_v2()
for replacing two identical calls in set_sample_rate_v2().
No functional change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, a new platform device is created for secondary device
by calling platform_device_register_resndata and then the drvdata
is set for this device.
The following patch has been added to driver core:
"driver core: fix possible missing of device probe".
This results in the added device getting probed immediately but
the drvdata for the secondary device is not yet set.
This patch removes the platform_device_register_resndata call and
instead calls platform_device_alloc, platform_set_drvdata and
platform_device_add which fixes the above issue.
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes a possible crash in case drvdata for the secondary
device is not set.
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move common code in ext4_ind_truncate() and ext4_ext_truncate() into
ext4_truncate(). This saves over 60 lines of code.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>