- Make sure we always hold the lock when setting / checking resetting
- Check resetting before checking urb->status
- Add missing check for resetting to uas_data_cmplt
- Add missing check for resetting to uas_do_work
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are various bug reports about oopses / hangs with the uas driver,
which all point to the abort-command and logical-unit-reset (task-management)
error handling paths.
Getting these right is very hard, there are quite a few corner cases, and
testing is almost impossible since under normal operation these code paths
are not used at all.
Another problem is that there are also some cases where it simply is not clear
what to do at all. E.g. over usb-2 multiple outstanding commands share the same
endpoint. What if a command gets aborted while its sense urb is half way
through completing (so some data has been transfered but not all). Since the
urb is not yet complete we don't know if the sense urb is actually for this
command, or for one of the other oustanding commands. If it is for one of the
other commands and we cancel it, then we end up in an undefined state. But if
it is actually for the command we're aborting, and the abort succeeds, then it
may never complete...
This exact same problem applies to logical unit resets too, if there are
multiple luns, then commands outstanding on both luns share the sense
endpoint. If there is only a single lun, then doing a logical unit reset is
little better then doing a full usb device reset.
So summarizing because:
1) abort / lun-reset is very tricky to get right
2) Not being able to test the tricky code, which means it will have bugs
3) This being a code path which under normal operation will never happen,
so being slow / sub-optimal here is not really an issue
4) Under error conditions we will still be able to recover through usb
device resets.
5) This may be a bit slower in some cases, but this is actually faster in
cases where the bridge ship has locked up, which seems to be the most
common error case sofar.
This commit removes the abort / lun-reset error handling paths, and also the
taks-mgmt code since those are the only 2 task-mgmt users. Leaving only the
(tested and testable) usb-device-reset error handling path in place.
Note I realize that this is somewhat of a big hammer, but currently people
are seeing very hard to debug oopses with uas. First let focus on making uas
work reliable, then we can later look into adding more fine grained error
handling.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As most ASM1051 based devices, this one has unfixable issues with uas too.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Besides the ASM1051 (*) needing sdev->no_report_opcodes = 1, it turns out that
the JMicron JMS567 also needs it to work properly with uas (usb-storage always
sets it). Since some of the scsi devs were not to keen on the idea to
outrightly set sdev->no_report_opcodes = 1 for all uas devices, so add a quirk
for this, and set it for the JMS567.
*) Which has become a non-issue since we've completely blacklisted uas on
the ASM1051 for other reasons
Cc: stable@vger.kernel.org
Reported-and-tested-by: Claudio Bizzarri <claudio.bizzarri@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And set this quirk for the Seagate Expansion Desk (0bc2:2312), as that one
seems to hang upon receiving an ATA_12 or ATA_16 command.
https://bugzilla.kernel.org/show_bug.cgi?id=79511https://bbs.archlinux.org/viewtopic.php?id=183190
While at it also add missing documentation for the u value for usb-storage
quirks.
Cc: stable@vger.kernel.org # 3.16, 3.17
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
--
Changes in v2: Add documentation for new t and u usb-storage.quirks flags
Changes in v3: Fix typo in documentation
Changes in v4: Also apply the quirk to (0bc2:3312)
Changes in v5: Rebased on 3.17-rc5, drop u documentation, already upstream
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
since commit 31964ffebb ("tty: serial: msm: Remove direct access to GSBI")'
serial hangs if earlyprintk are enabled.
This hang is noticed only when the GSBI driver is probed and all the
earlyprintks before gsbi probe are seen on the console.
The reason why it hangs is because GSBI driver disables hclk in its
probe function without realizing that the serial IP might be in use by
a bootconsole. As gsbi driver disables the clock in probe the
bootconsole locks up.
Turning off hclk's could be dangerous if there are system components
like earlyprintk using the hclk.
This patch fixes the issue by delegating the clock management to
probe and remove functions in gsbi rather than disabling the clock in probe.
More detailed problem description can be found here:
http://www.spinics.net/lists/linux-arm-msm/msg10589.html
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
on some architecture spin_is_locked() always return false in
uniprocessor configuration and therefore it would be advise
to replace with lockdep_assert_held().
Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the ehci-st.c and ohci-st.c files for the usb 2.0
& usb1.1 host controller drivers found on stih41x and stih4xx STMicroelectronics
SoC's into the STI arch section of the maintainers file.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch documents the device tree bindings required for
the ohci on-chip controller found in ST consumer electronics SoC's.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch documents the device tree bindings required for the
ehci on-chip controller found in ST consumer electronics SoC's.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the glue code required to ensure the on-chip OHCI
controller works on STi consumer electronics SoC's from STMicroelectronics.
It mainly manages the setting and enabling of the relevant clocks and manages
the reset / power signals to the IP block.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the glue code required to ensure the on-chip EHCI
controller works on STi consumer electronics SoC's from STMicroelectronics.
It mainly manages the setting and enabling of the relevant clocks and manages
the reset / power signals to the IP block.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_ioremap_resource to simplify error handling in the probe
function and to get rid of some boilerplate in the remove function.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds chipidea to the list of DT vendor prefixes.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some kernel-doc style comment are not satisfied for format, fix them.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have only needed to enable otg initialization when both of
below conditions are satisfied:
- The controller is otg capable
- The gadget function is enabled
If the controller is otg capable, but is host-only configuration, we do
not need to access register otgsc and do any otg operations (eg, create
otg workqueue).
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds Vybrid VF610 SoC support. The IP is very similar to i.MX6,
however, the non-core registers are spread in two different register
areas. Hence we support multiple instances of the USB misc driver
and add the driver instance to the imx_usbmisc_data structure.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TPL (Targeted Peripheral List) is needed for targets host
(OTG and Embedded Hosts) for usb certification and other
vendor specific requirements.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For OTG and Embedded hosts, they may need TPL (Targeted Peripheral List)
for usb certification and other vender specific requirements, the
platform can tell chipidea core driver if it supports tpl through DT
or platform data.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TPL (Targeted Peripheral List) is used for targeted hosts
(non-PC hosts), and it can be used at USB OTG & EH certification
and some specific products which need white list.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update configuration for USB_OTG_WHITELIST, any targeted hosts
(non PC-hosts) can have TPL (Targered Peripheral List).
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to On-The-Go and Embedded Host Supplement to the USB Revision
2.0 Specification, the targeted hosts (non-PC hosts) include both
embedded hosts and otg, and each targeted host product defines the
set of supported peripherals on a TPL (Targeted Peripheral List). So,
TPL should apply for both OTG and embedded host, and the otg support is
not a must for embedded host.
The TPL support feature will only be effect when CONFIG_USB_OTG_WHITELIST
has been chosen and hcd->tpl_support flag is set, it can avoid the enumeration
fails problem for the user who chooses CONFIG_USB_OTG_WHITELIST wrongly.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The targeted hosts (non-PC hosts) need to have TPL (Targeted Peripheral List)
for USB OTG & EH certification and other vendor specific requirements.
The platform who needs TPL feature should set this flag at usb host
controller driver.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Alpha EV4/EV5 cpus can corrupt adjacent byte and short data because
those cpus use RMW to store byte and short data. Thus, concurrent adjacent
byte stores could become corrupted, if serialized by a different lock.
tty_struct uses different locks to protect certain fields within the
structure, and thus is vulnerable to byte stores which are not atomic.
Merge the ->ctrl_status byte and packet mode bit, both protected by the
->ctrl_lock, into an unsigned long.
The padding bits are necessary to force the compiler to allocate the
type specified; otherwise, gcc will ignore the type specifier and
allocate the minimum number of bytes required to store the bitfield.
In turn, this would allow Alpha EV4/EV5 cpus to corrupt adjacent byte
or short storage (because those cpus use RMW to store byte and short data).
gcc versions < 4.7.2 will also corrupt storage adjacent to bitfields
smaller than unsigned long on ia64, ppc64, hppa64, and sparc64, thus
requiring more than unsigned int storage (which would otherwise be
sufficient to fix the Alpha non-atomic storage problem).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While transmitting a START/STOP char for tcflow(TCION/TCIOFF), prevent
a termios change. Otherwise, a garbage in-band flow control char
may be sent, if the termios change overlaps the transmission setup.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Relocate the file-scope function, send_prio_char(), as a global
helper tty_send_xchar(). Remove the global declarations for
tty_write_lock()/tty_write_unlock(), as these are file-scope only now.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use newly-introduced tty->flow_lock to serialize updates to
tty->flow_stopped (via tcflow()) and with concurrent tty flow
control changes from other sources.
Merge the storage for ->stopped and ->flow_stopped, now that both
flags are serialized by ->flow_lock.
The padding bits are necessary to force the compiler to allocate the
type specified; otherwise, gcc will ignore the type specifier and
allocate the minimum number of bytes necessary to store the bitfield.
In turn, this would allow Alpha EV4 and EV5 cpus to corrupt adjacent
byte storage because those cpus use RMW to store byte and short data.
gcc versions < 4.7.2 will also corrupt storage adjacent to bitfields
smaller than unsigned long on ia64, ppc64, hppa64 and sparc64, thus
requiring more than unsigned int storage (which would otherwise be
sufficient to workaround the Alpha non-atomic byte/short storage problem).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a master pty is set to packet mode, flow control changes to
the slave pty cause notifications to the master pty via reads and
polls. However, these tests are occurring for all ttys, not
just ptys.
Implement flow control packet mode notifications in the pty driver.
Only the slave side implements the flow control handlers since
packet mode is asymmetric; the master pty receives notifications
for slave-side changes, but not vice versa.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without serialization, the flow control state can become inverted
wrt. the actual hardware state. For example,
CPU 0 | CPU 1
stop_tty() |
lock ctrl_lock |
tty->stopped = 1 |
unlock ctrl_lock |
| start_tty()
| lock ctrl_lock
| tty->stopped = 0
| unlock ctrl_lock
| driver->start()
driver->stop() |
In this case, the flow control state now indicates the tty has
been started, but the actual hardware state has actually been stopped.
Introduce tty->flow_lock spinlock to serialize tty flow control changes.
Split out unlocked __start_tty()/__stop_tty() flavors for use by
ioctl(TCXONC) in follow-on patch.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stopped, hw_stopped, flow_stopped and packet bits are smp-unsafe
and interrupt-unsafe. For example,
CPU 0 | CPU 1
|
tty->flow_stopped = 1 | tty->hw_stopped = 0
One of these updates will be corrupted, as the bitwise operation
on the bitfield is non-atomic.
Ensure each flag has a separate memory location, so concurrent
updates do not corrupt orthogonal states. Because DEC Alpha EV4 and EV5
cpus (from 1995) perform RMW on smaller-than-machine-word storage,
"separate memory location" must be int instead of byte.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_set_termios() is called with interrupts enabled; no need to
save and restore the interrupt state when taking the uart port lock.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 64851636d5,
serial: bfin-uart: Remove ASYNC_CTS_FLOW flag for hardware automatic CTS,
open-codes uart_handle_cts_change() when CONFIG_SERIAL_BFIN_HARD_CTSRTS
to skip start and stop tx.
But the CTS interrupt handler _still_ calls uart_handle_cts_change();
only call uart_handle_cts_change() if !CONFIG_SERIAL_BFIN_HARD_CTSRTS.
cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty core does not test tty->hw_stopped; remove from drivers
which don't test it themselves.
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty->hw_stopped is not used by the tty core and is thread-unsafe;
hw_stopped is a member of a bitfield whose fields are updated
non-atomically and no lock is suitable for serializing updates.
Replace serial core usage of tty->hw_stopped with uport->hw_stopped.
Use int storage which works around Alpha EV4/5 non-atomic byte storage,
since uart_port uses different locks to protect certain fields within the
structure.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ISDN4Linux always enables CTS flow control and does not use the
tty_port_cts_enabled() helper function; remove ASYNC_CTS_FLOW
state enable/disable.
cc: Karsten Keil <isdn@linux-pingi.de>
cc: <netdev@vger.kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core uses the tty port flags, ASYNC_CTS_FLOW and
ASYNC_CD_CHECK, to track whether CTS and DCD changes should be
ignored or handled. However, the tty port flags are not safe for
atomic bit operations and no lock provides serialized updates.
Introduce the struct uart_port status field to track CTS and DCD
enable states, and serialize access with uart port lock. Substitute
uart_cts_enabled() helper for tty_port_cts_enabled().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core provides two helper functions, uart_handle_dcd_change()
and uart_handle_cts_change(), for UART drivers to use at interrupt
time. The serial core expects the UART driver to hold the uart port lock
when calling these helpers to prevent state corruption.
If lockdep enabled, trigger a warning if the uart port lock is not held
when calling these helper functions.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable device-qualifier quirk for Elan Touchscreen, which often fails to
handle requests for the device_descriptor.
Note that the device sometimes do respond properly with a Request Error
(three times as USB core retries), but usually fails to respond at all.
When this happens any further descriptor requests also fails, for
example:
[ 1528.688934] usb 2-7: new full-speed USB device number 4 using xhci_hcd
[ 1530.945588] usb 2-7: unable to read config index 0 descriptor/start: -71
[ 1530.945592] usb 2-7: can't read configurations, error -71
This has been observed repeating for over a minute before eventual
successful enumeration.
Reported-by: Drew Von Spreecken <drewvs@gmail.com>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new quirk for devices that cannot handle requests for the
device_qualifier descriptor.
A USB-2.0 compliant device must respond to requests for the
device_qualifier descriptor (even if it's with a request error), but at
least one device is known to misbehave after such a request.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An interface may need to assert a lock invariant and not flood the
system logs; add a lockdep helper macro equivalent to
lockdep_assert_held() which only WARNs once.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the following checkpatch.pl error:
ERROR: do not initialise statics to 0 or NULL
Signed-off-by: Catalina Mocanu <catalina.mocanu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WARNING : Missing a blank line after declaration
checkpatch.pl warning in hal_init.c
Signed-off-by: Sarah Khan <sarahjmi07@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the following checkpatch.pl warning:
WARNING: else is not generally useful after a break or return
Signed-off-by: Mahati Chamarthy <mahati.chamarthy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch merges an assignment with an immediately following return of
the assigned variable. It also removes variables that became unused due to this transformation.
The following Coccinelle semantic patch was used to make this transformation:
@r@
identifier ret;
identifier f;
@@
-ret =
+return
f(...);
-return ret;
@@
identifier r.ret;
expression e1;
type t;
@@
(
-t ret = e1;
|
-t ret;
)
... when != ret
when strict
Signed-off-by: Mahati Chamarthy <mahati.chamarthy@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes unncessary variable in file r8192U_core.c
using Coccinelle. Semantic patch for this is as follows :
@@
identifier ret;
@@
-int ret = 0;
... when != ret
when strict
-return ret;
+return 0;
Signed-off-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch merges an assignment with an immediately following return of
the assigned variable. It also removes a variable that becomes unused due to this transformation.
The following Coccinelle semantic patch was used to make this transformation:
@r@
identifier ret;
identifier f;
@@
-ret =
+return
f(...);
-return ret;
@@
identifier r.ret;
expression e1;
type t;
@@
(
-t ret = e1;
|
-t ret;
)
... when != ret
when strict
Signed-off-by: Mahati Chamarthy <mahati.chamarthy@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the following checkpatch.pl warning:
WARNING: Prefer [subsystem eg: netdev]_dbg([subsystem]dev, ... then
dev_dbg(dev, ... then pr_debug(... to printk(KERN_DEBUG ...
Removing the macro also fixes:
WARNING: macros should not use a trailing semicolon
Signed-off-by: Catalina Mocanu <catalina.mocanu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the following coccinelle warning:
WARNING: Assignment of bool to 0/1
Signed-off-by: Roberta Dobrescu <roberta.dobrescu@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
