This reverts commit e006fee6ec.
This patch causes build break. Modifications in Makefile and Kconfig have
no connection with driver code.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function may return an -ENODEV if debugfs is
disabled in kernel. This should originally be
guarded by ath10k's Kconfig but it still makes
sense to check for the non-NULL errno return
value.
Reported-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.1 firmware does not have an official way to
cause assert on purpose, but it can be done with
carefully crafted WMI command. This is a different
kind of crash from the 'hard' crash, which is
a bad memory dereference.
Different crashes decode in different manners, so
this will help the crash-report testing as well as
offer better ways to test firmware failure and
recovery.
kvalo: move the wmi command creation to debug.c, modify
the info print
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add testmode interface for starting and using UTF firmware which is used to run
factory tests. This is implemented by adding new state ATH10K_STATE_UTF and user
space can enable this state with ATH10K_TM_CMD_UTF_START command. To go back to
normal mode user space can send ATH10K_TM_CMD_UTF_STOP.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
now that we don't need to support legacy board-files,
we can completely switch over to a linear irq domain
and make use of irq_alloc_domain_generic_chips() to
allocate all generic irq chips for us.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
we don't need the ifdef if we have omap_nr_pending
telling us how many pending registers we have
on current platform. This solves a possible
problem where we could try to handle bogus
interrupts on OMAP2 and OMAP3 if using single
zImage kernel, because we would end up reading
the following pending FIQ register.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
that variable will tell us how many INTC_PENDING_IRQn
registers we have. It'll be used on a following patch
to cleanup omap_intc_handle_irq() a bit.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
we can set our global omap_nr_irqs early on
and drop the extra argument to omap_init_irq().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
that was just a no-op wrapper around omap_intc_handle_irq
anyway.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
now that we're calling set_handle_irq() from
init_irq(), we can safely drop all callers to
omap3_intc_handle_irq() and its definition.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
the idea is that board-files won't need to set
.handle_irq on their machine_descs, which lets
us drop a little more pointless code.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want .init_irq to call set_irq_handle() for
legacy platforms. Note that this code will also
be dropped once omap2/3 devices are completely
moved to DT.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
we are now infering number of IRQ lines based
on correct compatible flag, which renders this
binding completely useless.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
we don't need that anymore since specific
devices are passing correct compatible flags.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
that way, our intc driver can figure out how
many IRQ lines INTC has.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
so far, only am33xx has 128 lines, all other devices
have only 96.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
with this, we can use a compatible flag to figure
out how many irq lines are wired up, no need for
our TI-specific ti,intc-size binding.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
now we can safely drop those fields from our machine_desc.
While at that, also drop the now unused omap_intc_of_init()
definition.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
IRQCHIP_DECLARE macro is used to declare the same
of_device_id structure for irqchips, it's just
a helper. No functional changes.
Note that we're temporarily including irqchip.h
with its full path, until we move this driver
to drivers/irqchip/.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
this will let us drop .handle_irq and .init_irq fields
from our generic machine_descs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
nobody uses that function outside of this file,
so we don't need to expose it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
remove ifdef around omap3 INTC support. This
will make it easier to reuse code for PM.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_intc_handle_irq now had an unnecessary
base_addr argument. Let's remove it and fix
all callers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
an almost blind conversion from readl_relaxed
to our newly introduced intc_readl().
While at that, also remove some hardcoded
register addresses.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
this will cache number of irqs. Also in preparation
for removal of irq_banks array.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have a single bank in that array, this patch
is in preparation to remove that array. It just
shifts everything to a new set of functions
for register IO while also removing old ones.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is in preparation for removing the pointless
irq_banks array.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Fix for the cpufreq Operation Performance Points (OPP) code
where a recent commit added a kcalloc() call with an incorrect
ordering of arguments. From Anand Moon.
- Reverts of two ACPI battery commits that caused incorrect
diagnostic information to be printed to dmesg in some cases
from Bjørn Mork.
- Fix for the ACPI RTC operation region handler that applied the
& operator to an argument already representing an address and
that caused it to overwrite its own argument instead of writing
to the address contained in it as expected. From Chun-Yi Lee.
- Fix for the PM domain implementation in the ACPI LPSS (Low-Power
Subsystem) driver where one callback pointer pointed to a wrong
routine and one was NULL, but it shouldn't. From Fu Zhonghui.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=FgS1
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are regression fixes (cpufreq, ACPI battery) and fixes for stuff
that never worked correctly (ACPI RTC operation region handler and PM
domain implementation in the ACPI LPSS driver).
Specifics:
- Fix for the cpufreq Operation Performance Points (OPP) code where a
recent commit added a kcalloc() call with an incorrect ordering of
arguments. From Anand Moon.
- Reverts of two ACPI battery commits that caused incorrect
diagnostic information to be printed to dmesg in some cases from
Bjørn Mork.
- Fix for the ACPI RTC operation region handler that applied the &
operator to an argument already representing an address and that
caused it to overwrite its own argument instead of writing to the
address contained in it as expected. From Chun-Yi Lee.
- Fix for the PM domain implementation in the ACPI LPSS (Low-Power
Subsystem) driver where one callback pointer pointed to a wrong
routine and one was NULL, but it shouldn't. From Fu Zhonghui"
* tag 'pm+acpi-3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / LPSS: complete PM entries for LPSS power domain
Revert "ACPI / battery: fix wrong value of capacity_now reported when fully charged"
Revert "ACPI / battery: Fix warning message in acpi_battery_get_state()"
ACPI / RTC: Fix CMOS RTC opregion handler accesses to wrong addresses
cpufreq / OPP: Fix the order of arguments for kcalloc()
of_device_ids (i.e. compatible strings and the respective data) are not
supposed to change at runtime. All functions working with of_device_ids
provided by <linux/of.h> work with const of_device_ids. So mark the
non-const function parameters and structs for OMAP2+ as const, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The definition
static const char *omap3_boards_compat[] __initconst = {
defines a changable array of constant strings. That is you must not do:
*omap3_boards_compat[0] = 'f';
but
omap3_boards_compat[0] = "another string";
is fine. So the annotation __initconst is wrong and yields a compiler
error when other really const variables are added with __initconst.
As the struct machine_desc member dt_compat is declared as
const char *const *dt_compat;
making the arrays const is the better alternative over changing all
annotations to __initdata.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The NoA duration for a GO is half the beacon interval
and a concurrent context like a STA can be active only
for that duration, before switching back to the GO's
operating channel.
Currently, when multiple beacons are missed, the dwell
time for the STA context is extended to improve the
chances of receiving a beacon. But the NoA is not updated
and this will cause problems since the GO is offline
for a period that is longer than the advertised duration.
Fix this by ensuring that the NoA is updated first before
extending the time slot for the STA context. Also make
sure that non-periodic NoA is used for a one-time, longer
absence period.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the NoA duration is the maximum time the GO interface
can be offline, it needs to include the time take to
switch channels in the HW.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clearing the offchannel duration value in the
scheduler unconditionally breaks NoA when
multiple contexts are active and an offchannel
request is deferred, for example, in a scan run.
Fix this by clearing the duration only if there
is no pending offchannel request.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* The index has to incremented only when advertising
a new NoA schedule.
* Switch to non-periodic NoA when starting a scan operation
and multiple channel contexts are active.
* Make sure that periodic NoA is advertised again when
scan ends. Since the offchannel timer moves the offchannel
state to IDLE after the GO operating channel becomes
active, use a flag "force_noa_update" to update the
NoA contents.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In multi-channel mode, an offchannel request will
be deferred if both contexts are active. The duration
of the offchannel operation is calculated but is
not stored in the scheduler state. Fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When interface stopped while running intensive Rx traffic, the following oops
observed:
[89846.734683] Call trace:
[89846.737117] [<ffffffc00083aa64>] dev_gro_receive+0xac/0x358
[89846.742674] [<ffffffc00083ae94>] napi_gro_receive+0x24/0xa4
[89846.748251] [<ffffffbffc1c2f88>] $x+0xec/0x1f8 [wil6210] wil_netif_rx_any
[89846.753547] [<ffffffbffc1c4830>] $x+0x34/0x54 [wil6210] wil_release_reorder_frame
[89846.758755] [<ffffffbffc1c48ac>] wil_release_reorder_frames+0x5c/0x78 [wil6210]
[89846.766044] [<ffffffbffc1c4bf8>] wil_tid_ampdu_rx_free+0x20/0x48 [wil6210]
[89846.772901] [<ffffffbffc1bedc8>] $x+0x190/0x1e8 [wil6210]
[89846.778285] [<ffffffbffc1c0ed4>] wmi_event_worker+0x230/0x2f8 [wil6210]
[89846.784865] [<ffffffc0000b0bc8>] process_one_work+0x278/0x3fc
[89846.790591] [<ffffffc0000b1218>] worker_thread+0x200/0x330
[89846.796060] [<ffffffc0000b6664>] kthread+0xac/0xb8
[89846.800836] Code: b940c661 f9406a62 8b010041 f9400026 (f8636882)
[89846.807008] ---[ end trace d6fdc17cd27d18f6 ]---
Reason is the following: when removing Rx vring
(wil_netdev_ops.ndo_stop -> wil_stop -> wil_down -> __wil_down -> wil_rx_fini),
Rx interrupt occurs. It trigger Rx NAPI, calling wil_rx_handle() that reaps
(already cleaned) buffer, causing skb referring to garbage memory being set into reorder buffer.
Then, network stack trying to access this buffer and fails.
Prevent Rx NAPI from being scheduled if device going to stop. Bit wil_status_napi_en reflects
NAPI enablement state, check it when triggering Rx NAPI.
Testing shows that check for wil_status_napi_en sometimes gets negative, and new error message
get printed - in this case kernel oops would be observed. Original oops is no more reproducible.
This change requires also changes in the AP flows.
Properly enable/disable NAPI for the AP. Make sure Rx VRING is disabled
when resetting target.
For this, promote __wil_up() and __wil_down() to the module scope, and use it
in the relevant flows.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To better reflect real action performed, rename:
s/wil6210_disable_irq/wil_mask_irq/
s/wil6210_enable_irq/wil_unmask_irq/
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Expose firmware limit for the max_scan_ie_len;
also do actually set IE's for the probe request
max_scan_ie_len used to be 0, this blocks scan requests with non-zero IE's
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
re-use of wmi_ready for both FW ready event and for wmi_call was causing
false "FW not ready" indication in case wmi_call() was invoked while reset
took place.
add wmi_call completion variable instead of re-using wmi_ready.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HW supports upto 2304 packet size on the air.
HW is responsible for adding (Tx) or removing (Rx) the following headers:
802.11 hdr: 26B
SNAP: 8B
CRC: 4B
Security (optional): 24B
HW adds max 62B to the payload passed from driver. It means driver can use
max packet size of 2304-62 = 2242B
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
