- A correction on imx6dl gpu axi clock setting
- Fix a compilation error which comes after ARMv6K SMP build is allowed
- Fix a typo with pinctrl_esdhc1 in vf610-twr dts
- Correct i.MX6SX pad setting for UART in dts
- Fix i.MX53 VPU clock settings in dts
- Fix a suspend/resume failure seen on Cubox-i board, which is caused
by TLB missing of IOMUXC base address during suspend
- ARCH_HAS_OPP has been removed by commit 78c5e0bb14 (PM / OPP:
Remove ARCH_HAS_OPP), so we need to kill it for IMX
- A small fix on enet reset pin of edmqmx6 board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT80G9AAoJEFBXWFqHsHzOCWQH/0mMyczEhE4bejf7GW/P3+3q
CFsImryJv1PYYpGvzT/ez29Z7Ems4sftRK027BjvkCvYfRYSqEILrvI+UbhPYWHb
G7wR+uWpyb4uBacRDdFNCgcqnYlAhjprdwHbgOfwiiOvM+r3a1TGMg0cNnZA/Rfl
uWeW+2siUSeY+DK9qPLGeiJv5JzIMVQUowlnACQ8/NoYf9l+pjKQvPrLabJcygjC
XnbIDj/699RYKoZw+NKIv5kUSjJrzAEwAgPz78moL0MJANwce78PSlTSLbztC25W
3o1/ByUIaZkeg2a4SGgzXhHXIzQS26EgxZtIQbyZ1/QS+T/uxAiDo9HCARQ9SF4=
=+C4o
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 3.17" from Shawn Guo:
The i.MX fixes for 3.17:
- A correction on imx6dl gpu axi clock setting
- Fix a compilation error which comes after ARMv6K SMP build is allowed
- Fix a typo with pinctrl_esdhc1 in vf610-twr dts
- Correct i.MX6SX pad setting for UART in dts
- Fix i.MX53 VPU clock settings in dts
- Fix a suspend/resume failure seen on Cubox-i board, which is caused
by TLB missing of IOMUXC base address during suspend
- ARCH_HAS_OPP has been removed by commit 78c5e0bb14 (PM / OPP:
Remove ARCH_HAS_OPP), so we need to kill it for IMX
- A small fix on enet reset pin of edmqmx6 board
* tag 'imx-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx: fix the pad setting for uart CTS_B
ARM: dts: i.MX53: fix apparent bug in VPU clks
ARM: imx: correct gpu2d_axi and gpu3d_axi clock setting
ARM: dts: imx6: edmqmx6: change enet reset pin
ARM: dts: vf610-twr: Fix pinctrl_esdhc1 pin definitions.
ARM: imx: remove unnecessary ARCH_HAS_OPP select
ARM: imx: fix TLB missing of IOMUXC base address during suspend
ARM: imx6: fix SMP compilation again
Signed-off-by: Olof Johansson <olof@lixom.net>
This enables the netfilter NAT engine in first place, otherwise
you cannot ever select the nf_tables nat expression if iptables
is not selected.
Reported-by: Matteo Croce <technoboy85@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There's actually no good reason why we cannot use cgroup id 0,
so lets just remove this artificial barrier.
Reported-by: Alexey Perevalov <a.perevalov@samsung.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Tested-by: Alexey Perevalov <a.perevalov@samsung.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If the pending buffers in the queue could not be pushed to the udc
endpoint we have to cancel the uvc_queue. Otherwise the gadget will get
stuck on this error. This patch calls uvc_queue_cancel if usb_ep_queue
failed.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
All what these 'drivers' do is expose a single (non standard ABI) sysfs
attribute that when written to does a direct pass-through to spi_write(). This
is rather ugly and does not justify the existence of a driver as the same can
easily done by using the spidev interface.
The drivers will eventually be rewritten as proper IIO ABI compliant drivers
which do have the proper abstraction layers between userspace and the device.
But in the meantime these driver do not add any extra value and just clutter up
the staging area. So just remove them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add Michael and myself as the maintainer for the Analog Devices IIO drivers.
The entry matches on all files in drivers/staging/iio and drivers/iio/ starting
with the 'ad' prefix, except for 'adjd' as that one is used by Avago
Technologies.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Now that we support 48-bit physical addressing, update MAX_PHYSMEM_BITS
accordingly.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ganapatrao Kulkarni <ganapatrao.kulkarni@caviumnetworks.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
UEFI provides its own method for marking regions to reserve, via the
memory map which is also used to initialise memblock. So when using the
UEFI memory map, ignore any memreserve entries present in the DT.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add those persons who generally tend to review new IIO patches to the list of
designated reviewers to make sure that they are Cc'ed on new patches.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Meerwald <pmeerw@pmeerw.net>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The below patch improves the documentation for the gpio-property. Stephen
Warren has a good example here:
09789801
trackpad@4b {
compatible = "atmel,maxtouch";
reg = <0x4b>;
interrupt-parent = <&gpio>;
interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_LEVEL_LOW>;
linux,gpio-keymap = <0 0 0 BTN_LEFT>;
};
This maps BTN_LEFT to the 4th bit of the T19 message.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Change the comment type (from /** to /*) to prevent DocBook from
complaining about missing description for nand_sdr_timings fields.
There is currently no need in documenting those fields because they are
fully described in the ONFI specification (which is pointed out in the
comment).
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It's a one-liner doing no magic and its name may be confusing because
it does not have to use JEDEC (e.g. when using alternative read_id).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix the bug in handling gpio flash read/write when offset + len
from MTD exceeds the window size
Signed-off-by: Aaron Wu <Aaron.wu@analog.com>
[Brian: made some commentary edits. Also note that the BUG_ON() was
provably false for all non-negative inputs (since x % y <= x), so we
dropped it.]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
drivers/mtd/nand/nand_timings.c:45: warning: integer constant is too large for ‘long’ type
[ Editorial note: This is a false warning. Looking at ISO draft N1124
(this is approximately C11, the first PDF I had lying around),
section 6.4.4.1 (statement 5):
"The type of an integer constant is the first of the
corresponding list in which its value can be represented."
So this should not be an overflow, and any toolchain that says so
(e.g., GCC 4.4) is buggy.
-Brian ]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When enable NFC sram write, it will failed the mtd_nandbiterrs.ko test.
As in driver's nfc_sram_write_page(), if ops->mode equal to MTD_OSP_RAW,
driver assumes the data buffer contains one page data and one oob data
followed. And driver will write the page data and oob data to nand.
But this is wrong implementation. Since the data buffer don't contains the
oob data to write. We should write the chip->oob_poi to nand's oob.
So this patch fix it by writing the oob data from chip->oob_poi.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
chip->pagebuf is a 32-bit type (int), so the shift will only be applied
as 32-bit. Fix this for 64-bit safety.
Caught by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The condition "if (irq_status == 0)" already ensures that one half of
the ternary ?: is dead. I think this should probably actually be a FAIL,
not a PASS.
Caught by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Jamie Iles <jamie@jamieiles.com>
These multiplications are done with 32-bit arithmetic, then converted to
64-bit. We should widen the integers first to prevent overflow. This
could be a problem for large (>4GB) MTD's.
Detected by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
MTD used to allow compiling out character device support. This was
dropped in the following commit, but some of the accompanying logic was
never dropped:
commit 660685d9d1
Author: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Date: Thu Mar 14 13:27:40 2013 +0200
mtd: merge mtdchar module with mtdcore
The weird logic was flagged by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
There is one theoretical case that could fall through to using an
uninitialized value as the return code. Let's give it a value of 0.
Untested.
Caught by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When checking the upper boundary (i.e., whether an address is higher
than the maximum size of the MTD), we should be doing an inclusive check
(greater or equal). For instance, an address of 16MB (0x1000000) on a
16MB device is invalid.
The strengthening of this bounds check is redundant for those which
already have a address+length check and ensure that the length is
non-zero, but let's just fix them all, for completeness.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The variable 'retries' is never modified, so if the reset operation
never is going to complete, we'll get stuck in an infinite loop.
It looks like the intention was to decrement 'retries' on every loop.
Untested.
Caught by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Do nand reset before write protect check.
If we want to check the WP# low or high through STATUS READ and check bit 7,
we must reset the device, other operation (eg.erase/program a locked block) can
also clear the bit 7 of status register.
As we know the status register can be refreshed, if we do some operation to trigger it,
for example if we do erase/program operation to one block that is locked, then READ STATUS,
the bit 7 of READ STATUS will be 0 indicate the device in write protect, then if we do
erase/program operation to another block that is unlocked, the bit 7 of READ STATUS will
be 1 indicate the device is not write protect.
Suppose we checked the bit 7 of READ STATUS is 0 then judge the WP# is low (write protect),
but in this case the WP# maybe high if we do erase/program operation to a locked block,
so we must reset the device if we want to check the WP# low or high through STATUS READ and
check bit 7.
Signed-off-by: White Ding <bpqw@micron.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fixed checkpatch warnings: "WARNING: Prefer seq_puts to seq_printf"
This patch is created with reference to the ongoing lkml thread
https://lkml.org/lkml/2014/7/15/646
where Andrew Morton wrote:
"
- puts is presumably faster
- puts doesn't go rogue if you accidentally pass it a "%".
- this patch would actually make compiled object files few bytes smaller.
Perhaps because seq_printf() is a varargs function, forcing the
caller to pass args on the stack instead of in registers.
"
Signed-off-by: Samarth Parikh <samarthp@ymail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
MAP10 command with '0x2000' data sets up a read-ahead/write access.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds the support in the spi-nor driver of the Micron
M25PX80 flash, a 8 Mbit SPI flash from Micron.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix kernel-doc warning in <linux/mtd/nand.h>:
Warning(..//include/linux/mtd/nand.h:795): No description found for parameter 'ecc'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
PMECC can support 512, 1k, 2k, 4k, 8k page size.
The driver currently only support 2k page size nand flash. So this patch
add support to 512, 1k, 4k and 8k page size nand flash.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some nand with 8k page size like Micron MT29F32G08ABAAAWP need more than 20us.
Signed-off-by: Raphaël Poggi <poggi.raph@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use NULL instead of 0 when returning an address. This fixes a
sparse warning.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We check "cs" for array overflows but we don't check for underflows and
it upsets the static checkers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Remove all the material related to AIC5 support: this interrupt controller
driver is now implemented in drivers/irqchip/atmel-aic.c.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Remove selection of OLD_IRQ_AT91 when selecting dt boards.
Select ATMEL_AIC_IRQ for sama5 SoCs (a kernel compiled for this SoC will
always use ATMEL_AIC_IRQ driver).
Select ATMEL_AIC_IRQ for at91rm9200 and at91sam9 SoCs only if OLD_IRQ_AT91
is not selected (which means we are compiling a pure DT kernel, without
any legacy board support).
Remove specific irq init code in all dt board files: this init procedure
is automatically handled in of_irq_init which is called by the arm irq core
code and is in charge of calling the appropriate aic init functions.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Enclose at91_aic_xx calls in IS_ENABLED(CONFIG_OLD_IRQ_AT91) blocks in
order to prepare migration to the new AIC driver.
In the new AIC driver the suspend/resume functions are called by the
generic irq framework and are no longer needed in the PM specific code.
Moreover, the new AIC driver no longer exposes the at91_aic_base variable
which is used by the at91_aic_read functions.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Introduce the OLD_IRQ_AT91 Kconfig option to prepare migration to the
new AIC driver.
Select this option for all at91 SoCs and all available boards so that we
can later move DT enabled boards to the new irq driver and keep the old
implementation when legacy boards are selected.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Currently when run on an APM platform the ARMv8 defconfig has no viable
options for rootfs other than ramdisk which is rather limiting. Since
we already have both SATA and the bits needed for NFS root enabled we just
need to enable the relevant drivers so do that, helping enable direct
testing of upstream.
If the configuration ends up becoming too big we can consider modularising
some of the drivers and asking people to use an initramfs but for now this
is not an issue.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When booting via UEFI, the kernel Image is loaded at a 4 kB boundary and
the embedded EFI stub is executed in place. The EFI stub relocates the
Image to reside TEXT_OFFSET bytes above a 2 MB boundary, and jumps into
the kernel proper.
In AArch64, PC relative symbol references are emitted using adrp/add or
adrp/ldr pairs, where the offset into a 4 kB page is resolved using a
separate :lo12: relocation. This implicitly assumes that the code will
always be executed at the same relative offset with respect to a 4 kB
boundary, or the references will point to the wrong address.
This means we should link the kernel at a 4 kB aligned base address in
order to remain compatible with the base address the UEFI loader uses
when doing the initial load of Image. So update the code that generates
TEXT_OFFSET to choose a multiple of 4 kB.
At the same time, update the code so it chooses from the interval [0..2MB)
as the author originally intended.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Vasily Averin says:
====================
cbq: incorrectly low bandwidth blocks limited traffic
v2: patch description changes
Fixes: f0f6ee1f70 ("cbq: incorrect processing of high limits")
Mainstream commit f0f6ee1f70 ("cbq: incorrect processing of high limits")
have side effect: if cbq bandwidth setting is less than real interface
throughput non-limited traffic can delay limited traffic for a very long time.
This happen because of q->now changes incorrectly in cbq_dequeue():
in described scenario L2T is much greater than real time delay,
and q->now gets an extra boost for each transmitted packet.
Accumulated boost prevents update q->now, and blocked class can wait
very long time until (q->now >= cl->undertime) will be true again.
More detailed problem description can be found here:
http://www.spinics.net/lists/netdev/msg292493.html
Following patches should fix the problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now q->now_rt is identical to q->now and is not required anymore.
Signed-off-by: Vasily Averin <vvs@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mainstream commit f0f6ee1f70 ("cbq: incorrect processing of high limits")
have side effect: if cbq bandwidth setting is less than real interface
throughput non-limited traffic can delay limited traffic for a very long time.
This happen because of q->now changes incorrectly in cbq_dequeue():
in described scenario L2T is much greater than real time delay,
and q->now gets an extra boost for each transmitted packet.
Accumulated boost prevents update q->now, and blocked class can wait
very long time until (q->now >= cl->undertime) will be true again.
To fix the problem the patch updates q->now on each cbq_update() call.
L2T-related pre-modification q->now was moved to cbq_update().
My testing confirmed that it fixes the problem and did not discover
any side-effects
Fixes: f0f6ee1f70 ("cbq: incorrect processing of high limits")
Signed-off-by: Vasily Averin <vvs@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
