If bit-flips happen often, UBI prints to many messages. Lessen
the amount by only printing the messages when the PEB has been
scrubbed. Also, print torturing messages.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Quite useful ioctl which allows to make atomic system upgrades.
The idea belongs to Richard Titmuss <richard_titmuss@logitech.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The CFI_ADJUST_CFA_OFFSET dwarf2 annotation of a push/popf
pair in ret_from_fork wrongly used a value of 4. It should
have been 8. Fix that.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: heukelum@fastmail.fm
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Hch asked not to use "unit" for sub-systems, let it be so.
Also some other commentaries modifications.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Check that volume name is not shorter than 'name_len'.
No need to copy the trailing zero byte because whole array
was zeroed earlier.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
leb_read_unlock() may be called simultaniously by several tasks.
The would race at the following code:
up_read(&le->mutex);
if (free)
kfree(le);
And it is possible that one task frees 'le' before the other tasks
do 'up_read()'. Fix this by doing up_read and free inside the
'ubi->ltree' lock. Below it the oops we had because of this:
BUG: spinlock bad magic on CPU#0, integck/7504
BUG: unable to handle kernel paging request at 6b6b6c4f
IP: [<c0211221>] spin_bug+0x5c/0xdb
*pde = 00000000 Oops: 0000 [#1] PREEMPT SMP Modules linked in: ubifs ubi nandsim nand nand_ids nand_ecc video output
Pid: 7504, comm: integck Not tainted (2.6.26-rc3ubifs26 #8)
EIP: 0060:[<c0211221>] EFLAGS: 00010002 CPU: 0
EIP is at spin_bug+0x5c/0xdb
EAX: 00000032 EBX: 6b6b6b6b ECX: 6b6b6b6b EDX: f7f7ce30
ESI: f76491dc EDI: c044f51f EBP: e8a736cc ESP: e8a736a8
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process integck (pid: 7504, ti=e8a72000 task=f7f7ce30 task.ti=e8a72000)
Stack: c044f754 c044f51f 00000000 f7f7d024 00001d50 00000001 f76491dc 00000296 f6df50e0 e8a736d8 c02112f0 f76491dc e8a736e8 c039157a f7d9e830 f76491d8 e8a7370c c020b975 f76491dc 00000296 f76491f8 00000000 f76491d8 00000000 Call Trace:
[<c02112f0>] ? _raw_spin_unlock+0x50/0x7c
[<c039157a>] ? _spin_unlock_irqrestore+0x20/0x58
[<c020b975>] ? rwsem_wake+0x4b/0x122
[<c0390e0a>] ? call_rwsem_wake+0xa/0xc
[<c0139ee7>] ? up_read+0x28/0x31
[<f8873b3c>] ? leb_read_unlock+0x73/0x7b [ubi]
[<f88742a3>] ? ubi_eba_read_leb+0x195/0x2b0 [ubi]
[<f8872a04>] ? ubi_leb_read+0xaf/0xf8 [ubi]
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Normally UBI volumes are freed in the release function of
the struct device object. However, on error path they may
have to be freed before the struct device objects have been
initialized.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
UBI forgets to free internal volumes when detaching MTD device.
Fix this.
Pointed-out-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
ubi_free_volume() function sets ubi->volumes[] to NULL, so
ubi_eba_close() is useless, it does not free what has to be freed.
So zap it and free vol->eba_tbl at the volume release function.
Pointed-out-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
UBI already checks that @min io size is the power of 2 at io_init.
It is save to use bit operations then.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Instead of correctly pad the buffer wich we are writing to the
eraseblock during update, we used weird construct:
memset(buf + len, 0xFF, len - len);
Fix this.
Signed-off-by: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
It is not clear why we schedule PEB for scrubbing in case of
-EBADMSG. Elaborate.
Requested-by: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
ftrace requires certain low-level code, like spinlocks and timestamps,
to be compiled without -pg in order to avoid infinite recursion. This
patch splits out the core paravirt spinlocks and the Xen spinlocks
into separate files which can be compiled without -pg.
Also do xen/time.c while we're about it. As a result, we can now use
ftrace within a Xen domain.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
LTP testing showed that Xen does not properly implement
sys_modify_ldt(). This patch does the final little bits needed to
make the ldt work properly.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When implementing sysexit32, don't let Xen use sysret to return to
userspace. That results in usermode register state being trashed.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Call early_cpu_init() at the same (early) point in setup_arch().
The x86_64 code was calling it relatively late, after when other arch
code need to do cpu-related setup which depends on it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
remove the :vim=ft=help tag from trace files.
I used them years ago to syntax-highlight traces and forgot about this hack.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Dump the "flows" number according to the number of active flows
instead of repeating the "limit".
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although mv643xx_eth has no hardware support for inserting a vlan
tag by twiddling some bits in the TX descriptor, it does support
hardware TX checksumming on packets where the IP header starts {a
limited set of values other than 14} bytes into the packet.
This patch sets mv643xx_eth's ->vlan_features to NETIF_F_SG |
NETIF_F_IP_CSUM, which prevents the stack from checksumming vlan'ed
packets in software, and if vlan tags are present on a transmitted
packet, notifies the hardware of this fact by toggling the right
bits in the TX descriptor.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
When there is a link status change (link or phy status interrupt),
print a message notifying the user of the new link status.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The mv643xx_eth hardware has a provision for polling the PHY's
MII management registers to obtain the (R)(G)MII interface speed
(10/100/1000) and duplex (half/full) and pause (off/symmetric)
settings to use to talk to the PHY.
The driver currently does not make use of this feature. Instead,
whenever there is a link status change event, it reads the current
link parameters from the PHY, and programs those parameters into
the mv643xx_eth MAC by hand.
This patch switches the mv643xx_eth driver to letting the MAC
auto-determine the (R)(G)MII link parameters by PHY polling, if there
is a PHY present. For PHYless ports (when e.g. the (R)(G)MII
interface is connected to a hardware switch), we keep hardcoding the
MII interface parameters.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Instead of hardcoding MII register addresses and values, use the
symbolic constants defined in linux/mii.h.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The mv643xx_eth driver is limiting DMA bursts to 32 bytes, while
using the largest burst size (128 bytes) gives a couple percentage
points performance improvement in throughput tests, and the docs
say that the 128 byte default should not need to be changed, so
use 128 byte bursts instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The recommended sequence for waiting for the transmit path to clear
after disabling all of the transmit queues is to wait for the
TX_FIFO_EMPTY bit in the Port Status register to become set as well
as the TX_IN_PROGRESS bit to clear.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The maximum receive packet size field in the Port Serial Control
register controls at what size received packets are flagged
overlength in the receive descriptor, but it doesn't prevent
overlength packets from being DMAd to memory and signaled to the
host like other received packets.
mv643xx_eth does not support receiving jumbo frames in 10/100 mode,
but setting the packet threshold to larger than 1522 bytes in 10/100
mode won't cause breakage by itself.
If we really want to enforce maximum packet size on the receiving
end instead of on the sending end where it should be done, we can
always just add a length check to the software receive handler
instead of relying on the hardware to do the comparison for us.
What's more, changing the maximum packet size field requires
temporarily disabling the RX/TX paths. So once the link comes
up in 10/100 Mb/s mode or 1000 Mb/s mode, we'd have to disable it
again just to set the right maximum packet size field (1522 in
10/100 Mb/s mode or 9700 in 1000 Mb/s mode), just so that we can
offload one comparison operation to hardware that we might as well
do in software, assuming that we'd want to do it at all.
Contrary to what the documentation suggests, there is no harm in
just setting a 9700 byte maximum packet size in 10/100 mode, so use
the maximum maximum packet size for all modes.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The mv643xx_eth driver allows doing transmit reclaim from within the
napi poll routine, but after doing reclaim, it would forget to check
the free transmit descriptor count and wake up the transmit queue if
the reclaim caused enough descriptors for a new packet to become
available. This would cause the netdev watchdog to occasionally kick
in during certain workloads with combined receive and transmit traffic.
Fix this by adding a wakeup check identical to the one in the
interrupt handler to the napi poll routine.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
When the ethernet link goes down while mv643xx_eth is transmitting
data, transmit DMA can stop before all queued transmit descriptors
have been processed. But even the descriptors that _have_ been
processed might not be properly marked as done before the transmit
DMA unit shuts down.
Then when the link comes up again, the hardware transmit pointer
might have advanced while not all previous packet descriptors have
been marked as transmitted, causing software transmit reclaim to
hang waiting for the hardware to finish transmitting a descriptor
that it has already skipped.
This patch forcibly reclaims all packets on the transmit ring on a
link down interrupt, and then resyncs the hardware transmit pointer to
what the software's idea of the first free descriptor is. Also, we
need to prevent re-waking the transmit queue if we get a 'transmit
done' interrupt at the same time as a 'link down' interrupt, which
this patch does as well.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The previously merged TX hang erratum workaround ("mv643xx_eth:
work around TX hang hardware issue") assumes that TX_END interrupts
are delivered simultaneously with or after their corresponding TX
interrupts, but this is not always true in practise.
In particular, it appears that TX_END interrupts are issued as soon
as descriptor fetch returns an invalid descriptor, which may happen
before earlier descriptors have been fully transmitted and written
back to memory as being done.
This hardware behavior can lead to a situation where the current
driver code mistakenly assumes that the MAC has given up transmitting
before noticing the packets that it is in fact still currently working
on, causing the driver to re-kick the transmit queue, which will only
cause the MAC to re-fetch the invalid head descriptor, and generate
another TX_END interrupt, et cetera, until the packets in the pipe
finally finish transmitting and have their descriptors written back
to memory, which will then finally break the loop.
Fix this by having the erratum workaround not check the 'number of
unfinished descriptor', but instead, to compare the software's idea
of what the head descriptor pointer should be to the hardware's head
descriptor pointer (which is updated on the same conditions as the
TX_END interupt is generated on, i.e. possibly before all previous
descriptors have been transmitted and written back).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
* 'sched/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: hrtick_enabled() should use cpu_active()
sched, x86: clean up hrtick implementation
sched: fix build error, provide partition_sched_domains() unconditionally
sched: fix warning in inc_rt_tasks() to not declare variable 'rq' if it's not needed
cpu hotplug: Make cpu_active_map synchronization dependency clear
cpu hotplug, sched: Introduce cpu_active_map and redo sched domain managment (take 2)
sched: rework of "prioritize non-migratable tasks over migratable ones"
sched: reduce stack size in isolated_cpu_setup()
Revert parts of "ftrace: do not trace scheduler functions"
Fixed up conflicts in include/asm-x86/thread_info.h (due to the
TIF_SINGLESTEP unification vs TIF_HRTICK_RESCHED removal) and
kernel/sched_fair.c (due to cpu_active_map vs for_each_cpu_mask_nr()
introduction).
The AT91SAM9RL SoC integrates a Touchscreen Controller which
can trigger ADC conversion periodically.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Dan Liang <dan.liang@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
NR_CPUS: Replace NR_CPUS in speedstep-centrino.c
cpumask: Provide a generic set of CPUMASK_ALLOC macros, FIXUP
NR_CPUS: Replace NR_CPUS in cpufreq userspace routines
NR_CPUS: Replace per_cpu(..., smp_processor_id()) with __get_cpu_var
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genapic_flat_64.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genx2apic_uv_x.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/proc.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/mcheck/mce_64.c
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c, fix
cpumask: Use optimized CPUMASK_ALLOC macros in the centrino_target
cpumask: Provide a generic set of CPUMASK_ALLOC macros
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c
cpumask: Optimize cpumask_of_cpu in kernel/time/tick-common.c
cpumask: Optimize cpumask_of_cpu in drivers/misc/sgi-xp/xpc_main.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/ldt.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/io_apic_64.c
cpumask: Replace cpumask_of_cpu with cpumask_of_cpu_ptr
Revert "cpumask: introduce new APIs"
cpumask: make for_each_cpu_mask a bit smaller
net: Pass reference to cpumask variable in net/sunrpc/svc.c
...
Fix up trivial conflicts in drivers/cpufreq/cpufreq.c manually
* 'core/softlockup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
softlockup: fix invalid proc_handler for softlockup_panic
softlockup: fix watchdog task wakeup frequency
softlockup: fix watchdog task wakeup frequency
softlockup: show irqtrace
softlockup: print a module list on being stuck
softlockup: fix NMI hangs due to lock race - 2.6.26-rc regression
softlockup: fix false positives on nohz if CPU is 100% idle for more than 60 seconds
softlockup: fix softlockup_thresh fix
softlockup: fix softlockup_thresh unaligned access and disable detection at runtime
softlockup: allow panic on lockup
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (85 commits)
[ARM] pxa: add base support for PXA930 Handheld Platform (aka SAAR)
[ARM] pxa: add base support for PXA930 Evaluation Board (aka TavorEVB)
[ARM] pxa: add base support for PXA930 (aka Tavor-P)
[ARM] Update mach-types
[ARM] pxa: make littleton to use the new smc91x platform data
[ARM] pxa: make zylonite to use the new smc91x platform data
[ARM] pxa: make mainstone to use the new smc91x platform data
[ARM] pxa: make lubbock to use new smc91x platform data
[NET] smc91x: prepare SMC_USE_PXA_DMA to be specified in platform data
[NET] smc91x: prepare for SMC_IO_SHIFT to be a platform configurable variable
[NET] smc91x: add SMC91X_NOWAIT flag to platform data
[NET] smc91x: favor the use of SMC91X_USE_* instead of SMC_CAN_USE_*
[NET] smc91x: remove "irq_flags" from "struct smc91x_platdata"
[ARM] 5146/1: pxa2xx: convert all boards to call pxa2xx_transceiver_mode helper
Support for LCD on e740 e750 e400 and e800 e-series PDAs
E-series UDC support
PXA UDC - allow use of inverted GPIO for pullup
Add e350 support
Fix broken e-series build
E-series GPIO / IRQ definitions.
...
fs/cifs/cifssmb.c:3917:13: warning: incorrect type in assignment (different base types)
fs/cifs/cifssmb.c:3917:13: expected bool [unsigned] [usertype] is_unicode
fs/cifs/cifssmb.c:3917:13: got restricted __le16
The comment explains why __force is used here.
fs/cifs/connect.c:458:16: warning: cast to restricted __be32
fs/cifs/connect.c:458:16: warning: cast to restricted __be32
fs/cifs/connect.c:458:16: warning: cast to restricted __be32
fs/cifs/connect.c:458:16: warning: cast to restricted __be32
fs/cifs/connect.c:458:16: warning: cast to restricted __be32
fs/cifs/connect.c:458:16: warning: cast to restricted __be32
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
This patch adjusts the placement of a reference context from
a spu affinity chain. The reference context can now be placed
only on nodes that have enough spus not intended to be used by
another gang (already running on the node).
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
This adds fast paths for 32-bit syscall entry and exit when
TIF_SYSCALL_AUDIT is set, but no other kind of syscall tracing.
These paths does not need to save and restore all registers as
the general case of tracing does. Avoiding the iret return path
when syscall audit is enabled helps performance a lot.
Signed-off-by: Roland McGrath <roland@redhat.com>
Currenlt,, it is possible to lock aff_mutex and
cbe_spu_info[n].list_mutex in different orders, allowing a deadlock to
occur. With this change, aff_mutex is not taken within a list_mutex
critical section anymore.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
This adds fast paths for 32-bit syscall entry and exit when
TIF_SYSCALL_AUDIT is set, but no other kind of syscall tracing.
These paths does not need to save and restore all registers as
the general case of tracing does. Avoiding the iret return path
when syscall audit is enabled helps performance a lot.
Signed-off-by: Roland McGrath <roland@redhat.com>
