With a flash-based BBT there is no reason to move the Factory Bad
Block Marker from the data area buffer (to where it is mapped by the
GPMI NAND controller) to the OOB buffer. Thus, make this feature
configurable via DT. This is required for the Ka-Ro electronics
platforms.
In the original code 'this->swap_block_mark' was synonymous with
'!GPMI_IS_MX23()', so use the latter at the relevant places.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Michael has been backing me up and helping will all aspects of
maintainership for a while now, let's make it official.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Power8 has a new register (MMCR2), which contains individual freeze bits
for each counter. This is an improvement on previous chips as it means
we can have multiple events on the PMU at the same time with different
exclude_{user,kernel,hv} settings. Previously we had to ensure all
events on the PMU had the same exclude settings.
The core of the patch is fairly simple. We use the 207S feature flag to
indicate that the PMU backend supports per-event excludes, if it's set
we skip the generic logic that enforces the equality of excludes between
events. We also use that flag to skip setting the freeze bits in MMCR0,
the PMU backend is expected to have handled setting them in MMCR2.
The complication arises with EBB. The FCxP bits in MMCR2 are accessible
R/W to a task using EBB. Which means a task using EBB will be able to
see that we are using MMCR2 for freezing, whereas the old logic which
used MMCR0 is not user visible.
The task can not see or affect exclude_kernel & exclude_hv, so we only
need to consider exclude_user.
The table below summarises the behaviour both before and after this
commit is applied:
exclude_user true false
------------------------------------
| User visible | N N
Before | Can freeze | Y Y
| Can unfreeze | N Y
------------------------------------
| User visible | Y Y
After | Can freeze | Y Y
| Can unfreeze | Y/N Y
------------------------------------
So firstly I assert that the simple visibility of the exclude_user
setting in MMCR2 is a non-issue. The event belongs to the task, and
was most likely created by the task. So the exclude_user setting is not
privileged information in any way.
Secondly, the behaviour in the exclude_user = false case is unchanged.
This is important as it is the case that is actually useful, ie. the
event is created with no exclude setting and the task uses MMCR2 to
implement exclusion manually.
For exclude_user = true there is no meaningful change to freezing the
event. Previously the task could use MMCR2 to freeze the event, though
it was already frozen with MMCR0. With the new code the task can use
MMCR2 to freeze the event, though it was already frozen with MMCR2.
The only real change is when exclude_user = true and the task tries to
use MMCR2 to unfreeze the event. Previously this had no effect, because
the event was already frozen in MMCR0. With the new code the task can
unfreeze the event in MMCR2, but at some indeterminate time in the
future the kernel will overwrite its setting and refreeze the event.
Therefore my final assertion is that any task using exclude_user = true
and also fiddling with MMCR2 was deeply confused before this change, and
remains so after it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To support per-event exclude settings on Power8 we need access to the
struct perf_events in compute_mmcr().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Because we reuse cpuhw->mmcr on each call to compute_mmcr() there's a
risk that we could forget to set one of the values and use whatever
value was in there previously.
Currently all the implementations are careful to set all the values, but
it's safer to clear them all before we call compute_mmcr().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Although we expect some small discrepancies for very large counts, we
seem to be able to count up to 64 billion instructions without too much
skew, so do so.
Also switch to using decimals for the instruction counts. This just
makes it easier to visually compare the expected vs actual values, as
well as the raw result from instructions.
Before:
instructions: result 68719476753 running/enabled 13101961654
cycles: result 38077343785 running/enabled 13101725752
Looped for 68719476736 instructions, overhead 17
Expected 68719476753
Actual 68719476753
Delta 0, 0.000000%
success: count_instructions
After:
instructions: result 64000000016 running/enabled 12197599964
cycles: result 35412471674 running/enabled 12197534110
Looped for 64000000000 instructions, overhead 16
Expected 64000000016
Actual 64000000016
Delta 0, 0.000000%
success: count_instructions
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Have a task eat some cpu while we are counting instructions to create
some scheduler pressure. The idea being to try and unearth any bugs we
have in counting that only appear when context switching is happening.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is at least one bug in core_busy_loop(), we use r0, but it's
not in the clobber list. We were getting away with this it seems but
that was luck.
It's also fishy to be touching the stack, even if we do it below the
stack pointer. It seems we get away with it, but looking at the
generated code that may just be luck.
So move it into assembler, do all the stack handling by hand. We create
a stack frame to save the non-volatiles in, so we can muck around with
them.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
start and end should be unsigned long.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we ignore errors from our sub Makefiles. We inherited that
from the top-level selftests Makefile which aims to build and run as
many tests as possible and damn the torpedoes.
For the powerpc tests we'd instead like any errors to fail the build, so
we can automatically catch build failures.
We can achieve the best of both worlds by using -k, which tells make to
keep building when it hits an error, but still reports the error.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I spent ten minutes scratching my head, trying to work out where we
enabled relocation on interrupts for guest kernels. Expand the doco to
make it clear.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A lot of the code in platforms/pseries is using non-machine initcalls.
That means if a kernel built with pseries support runs on another
platform, for example powernv, the initcalls will still run.
Most of these cases are OK, though sometimes only due to luck. Some were
having more effect:
* hcall_inst_init
- Checking FW_FEATURE_LPAR which is set on ps3 & celleb.
* mobility_sysfs_init
- created sysfs files unconditionally
- but no effect due to ENOSYS from rtas_ibm_suspend_me()
* apo_pm_init
- created sysfs, allows write
- nothing checks the value written to though
* alloc_dispatch_log_kmem_cache
- creating kmem_cache on non-pseries machines
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A lot of the code in platforms/powernv is using non-machine initcalls.
That means if a kernel built with powernv support runs on another
platform, for example pseries, the initcalls will still run.
That is usually OK, because the initcalls will check for something in
the device tree or elsewhere before doing anything, so on other
platforms they will usually just return.
But it's fishy for powernv code to be running on other platforms, so
switch them all to be machine initcalls. If we want any of them to run
on other platforms in future they should move to sysdev.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
DISABLE_INTS has a long and storied history, but for some time now it
has not actually disabled interrupts.
For the open-coded exception handlers, just stop using it, instead call
RECONCILE_IRQ_STATE directly. This has the benefit of removing a level
of indirection, and making it clear that r10 & r11 are used at that
point.
For the addition case we still need a macro, so rename it to clarify
what it actually does.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The comment on TRACE_ENABLE_INTS is incorrect, and appears to have
always been incorrect since the code was merged. It probably came from
an original out-of-tree patch.
Replace it with something that's correct. Also propagate the message to
RECONCILE_IRQ_STATE(), because it's potentially subtle.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At the moment the allmodconfig build is failing because we run out of
space between altivec_assist() at 0x5700 and the fwnmi_data_area at
0x7000.
Fixing it permanently will take some more work, but a quick fix is to
move bad_stack() below the fwnmi_data_area. That gives us just enough
room with everything enabled.
bad_stack() is called from the common exception handlers, but it's a
non-conditional branch, so we have plenty of scope to move it further
way.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a strange #define in cputable.h called CLASSIC_PPC.
Although it is defined for 32 & 64bit, it's only used for 32bit and
it's basically a duplicate of CONFIG_PPC_BOOK3S_32, so let's use
the latter.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Although the name CONFIG_POWER4 suggests that it controls support for
power4 cpus, this symbol is actually misnamed.
It is a historical wart from the powermac code, which used to support
building a 32-bit kernel for power4. CONFIG_POWER4 was used in that
context to guard code that was 64-bit only.
In the powermac code we can just use CONFIG_PPC64 instead, and in other
places it is a synonym for CONFIG_PPC_BOOK3S_64.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are still a few occurences where it remains, because it helps to
explain something that persists.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We no longer support these cpus, so we don't need oprofile support for
them either.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that we have dropped power3 support we can remove CONFIG_POWER3. The
usage in pgtable_32.c was already dead code as CONFIG_POWER3 was not
selectable on PPC32.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The previous patch left a bit of a wart in copy_process(). Clean it up a
bit by moving the logic out into a helper.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We now only support cpus that use an SLB, so we don't need an MMU
feature to indicate that.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Old cpus didn't have a Segment Lookaside Buffer (SLB), instead they had
a Segment Table (STAB). Now that we've dropped support for those cpus,
we can remove the STAB support entirely.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We inadvertently broke power3 support back in 3.4 with commit
f5339277eb "powerpc: Remove FW_FEATURE ISERIES from arch code".
No one noticed until at least 3.9.
By then we'd also broken it with the optimised memcpy, copy_to/from_user
and clear_user routines. We don't want to add any more complexity to
those just to support ancient cpus, so it seems like it's a good time to
drop support for power3 and earlier.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we have sys_sigpending and sys_old_getrlimit defined to use
COMPAT_SYS() in systbl.h, but then both are #defined to sys_ni_syscall
in systbl.S.
This seems to have been done when ppc and ppc64 were merged, in commit
9994a33 "Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S".
AFAICS there's no longer (or never was) any need for this, we can just
use SYSX() for both and remove the #defines to sys_ni_syscall.
The expansion before was:
#define COMPAT_SYS(func) .llong .sys_##func,.compat_sys_##func
#define sys_old_getrlimit sys_ni_syscall
COMPAT_SYS(old_getrlimit)
=>
.llong .sys_old_getrlimit,.compat_sys_old_getrlimit
=>
.llong .sys_ni_syscall,.compat_sys_old_getrlimit
After is:
#define SYSX(f, f3264, f32) .llong .f,.f3264
SYSX(sys_ni_syscall, compat_sys_old_getrlimit, sys_old_getrlimit)
=>
.llong .sys_ni_syscall,.compat_sys_old_getrlimit
ie. they are equivalent.
Finally both COMPAT_SYS() and SYSX() evaluate to sys_ni_syscall in the
Cell SPU code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we have to copy data we must drop i_data_sem because of
get_blocks() will be called inside mext_page_mkuptodate(), but later we must
reacquire it again because we are about to change extent's tree
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Inode's depth can be changed from here:
ext4_ext_try_to_merge() ->ext4_ext_try_to_merge_up()
We must use correct value.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Each caller of ext4_ext_dirty must hold i_data_sem,
The only exception is migration code, let's make it convenient.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
As the member fe_len defined in struct ext4_free_extent is expressed as
number of clusters, the variable "size" computation is wrong, we need to
first translate fe_len to block number, then to bytes.
Signed-off-by: Xiaoguang Wang <wangxg.fnst@cn.fujitsu.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Lukas Czerner <lczerner@redhat.com>
The function rtas_flash_firmware passes the address of a data structure,
flash_block_list, when making the update-flash-64-and-reboot rtas call.
While the endianness of the address is handled correctly, the endianness
of the data is not. This patch ensures that the data in flash_block_list
is big endian when passed to rtas on little endian hosts.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We can continue to read the error log (up to MAX size) even if
we get the elog size more than MAX size. Hence change BUG_ON to
WARN_ON.
Also updated error message.
Reported-by: Gopesh Kumar Chaudhary <gopchaud@in.ibm.com>
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
STDDEV_THRESH was once defined and used in menu governor. But now its no longer
used anywhere. So removing the define.
Signed-off-by: Mohammad Merajul Islam Molla <meraj.enigma@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-pm:
ACPI / PM: Use ACPI_COMPANION() instead of ACPI_HANDLE()
ACPI / PM: Always enable wakeup GPEs when enabling device wakeup
ACPI / PM: Revork the handling of ACPI device wakeup notifications
PM: Create PM workqueue if runtime PM is not configured too
* acpi-sleep:
ACPI / sleep: Do not save NVS for new machines to accelerate S3
* acpi-button:
ACPI / button: Do not propagate wakeup-from-suspend events
