This patch attempts to handle RTAS "busy" return codes in a more simple
and consistent manner. Typical callers of RTAS shouldn't have to
manage wait times and delay calls.
This patch also changes the kernel to use msleep() rather than udelay()
when a runtime delay is necessary. This will avoid CPU soft lockups
for extended delay conditions.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
From: Andrew Morton <akpm@osdl.org>
arch/powerpc/Kconfig:339:warning: leading whitespace ignored
arch/powerpc/Kconfig:347:warning: leading whitespace ignored
arch/powerpc/Kconfig:357:warning: leading whitespace ignored
arch/powerpc/Kconfig:373:warning: leading whitespace ignored
arch/powerpc/Kconfig:382:warning: leading whitespace ignored
arch/powerpc/Kconfig:394:warning: leading whitespace ignored
arch/powerpc/Kconfig:842:warning: leading whitespace ignored
arch/powerpc/Kconfig:847:warning: leading whitespace ignored
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 970MP cputable entry needs a num_pmcs entry for oprofile to work.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My js20 appears to lack the ibm,#dma- properties, and boot fails with a
"Kernel panic - not syncing: iommu_init_table: Can't allocate 0 bytes"
message.
This adds a fallback to the "#address-cells" property in case the
"#ibm,dma-address-cells" property is missing. Tested on js20 and
power5 lpar.
Unless there is a more elegant solution... :-)
Signed-off-by: Will Schmidt <willschm@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Our MMU hash management code would not set the "C" bit (changed bit) in
the hardware PTE when updating a RO PTE into a RW PTE. That would cause
the hardware to possibly to a write back to the hash table to set it on
the first store access, which in addition to being a performance issue,
might also hit a bug when running with native hash management (non-HV)
as our code is specifically optimized for the case where no write back
happens.
Thus there is a very small therocial window were a hash PTE can become
corrupted if that HPTE has just been upgraded to read write, a store
access happens on it, and that races with another processor evicting
that same slot. Since eviction (caused by an almost full hash) is
extremely rare, the bug is very unlikely to happen fortunately.
This fixes by allowing the updating of the protection bits in the native
hash handling to also set (but not clear) the "C" bit, and, in order to
also improve performances in the general case, by always setting that
bit on newly inserted hash PTE so that writeback really never happens.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch cleans up some locking & error handling in the ppc vdso and
moves the vdso base pointer from the thread struct to the mm context
where it more logically belongs. It brings the powerpc implementation
closer to Ingo's new x86 one and also adds an arch_vma_name() function
allowing to print [vsdo] in /proc/<pid>/maps if Ingo's x86 vdso patch is
also applied.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I have tested PPC_PTRACE_GETREGS and PPC_PTRACE_SETREGS on umview.
I do not understand why historically these tags has been defined as
PPC_PTRACE_GETREGS and PPC_PTRACE_SETREGS instead of simply
PTRACE_[GS]ETREGS. The other "originality" is that the address must be
put into the "addr" field instead of the "data" field as stated in the
manual.
Signed-off-by: renzo davoli <renzo@cs.unibo.it>
Signed-off-by: Paul Mackerras <paulus@samba.org>
getting decremented by 1. Since nused never reaches 0, the "if
(!free->hdr.nused)" check in xfs_dir2_leafn_remove() fails every time and
xfs_dir2_shrink_inode() doesn't get called when it should. This causes
extra blocks to be left on an empty directory and the directory in unable
to be converted back to inline extent mode.
SGI-PV: 951958
SGI-Modid: xfs-linux-melb:xfs-kern:211382a
Signed-off-by: Mandy Kirkconnell <alkirkco@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
This allows to configure every symbol list and info window separately via a
popup menu, these settings are also separately saved and restored. Cleanup
the ConfigSettings class a bit to reduce the number of #ifdef.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Implement a simple search request for xconfig. Currently the capabilities are
rather simple (the same as menuconfig).
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This makes it possible to change two options which were hardcoded sofar.
1. Any symbol can now take the role of CONFIG_MODULES
2. The more useful option is to change the list of default file names,
which kconfig uses to load the base configuration if .config isn't
available.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This adds the general framework to the parser to define options for config
symbols with a syntax like:
config FOO
option bar[="arg"]
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This moves the .kernelrelease file into include/config directory. Remove its
generation from the config step, if the config step doesn't leave a proper
.config behind, it triggers a call to silentoldconfig. Instead its generation
can be done via proper dependencies.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Now that kconfig can load multiple configurations, it becomes simple to
integrate the split config step, by simply comparing the new .config file with
the old auto.conf (and then saving the new auto.conf). A nice side effect is
that this saves a bit of disk space and cache, as no data needs to be read
from or saved into the splitted config files anymore (e.g. include/config is
now 648KB instead of 5.2MB).
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Extend conf_read_simple() so it can load multiple configurations.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Extend struct symbol to allow storing multiple default values, which can be
used to hold multiple configurations.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The SYMBOL_{YES,MOD,NO} are not really used anymore (they were more used be
the cml1 converter), so just remove them.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This fixes one of the worst kbuild warts left - the broken dependencies used
to check and regenerate the .config file. This was done via an indirect
dependency and the .config itself had an empty command, which can cause make
not to reread the changed .config file.
Instead of this we generate now a new file include/config/auto.conf from
.config, which is used for kbuild and has the proper dependencies. It's also
the main make target now for all files generated during this step (and thus
replaces include/linux/autoconf.h).
This also means we can now relax the syntax requirements for the .config file
and we don't have to rewrite it all the time, i.e. silentoldconfig only
writes .config now when it's necessary to keep it in sync with the Kconfig
files and even this can be suppressed by setting the environment variable
KCONFIG_NOSILENTUPDATE, so the update can (and must) be done manually.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
During loading special case the first common case (.config), be silent about
it and otherwise mark it as a change that requires saving. Instead output
that the file has been changed. IOW if conf does nothing (special), it's
silent.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
truncate down followed by delayed allocation (buffered writes) - worst
case scenario for the notorious NULL files problem. This reduces the
window where we are exposed to that problem significantly.
SGI-PV: 917976
SGI-Modid: xfs-linux-melb:xfs-kern:26100a
Signed-off-by: Nathan Scott <nathans@sgi.com>
init_rwsem() has no return value. This is not a problem if init_rwsem()
is a function, but it's a problem if it's a do { ... } while (0) macro.
(which lockdep introduces)
SGI-PV: 904196
SGI-Modid: xfs-linux-melb:xfs-kern:26082a
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Nathan Scott <nathans@sgi.com>
logged version of di_next_unlinked which is actually always stored in the
correct ondisk format. This was pointed out to us by Shailendra Tripathi.
And is evident in the xfs qa test of 121.
SGI-PV: 953263
SGI-Modid: xfs-linux-melb:xfs-kern:26044a
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
transaction completion from marking the inode dirty while it is being
cleaned up on it's way out of the system.
SGI-PV: 952967
SGI-Modid: xfs-linux-melb:xfs-kern:26040a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
64bit kernels allow recovery to handle both versions and do the necessary
decoding
SGI-PV: 952214
SGI-Modid: xfs-linux-melb:xfs-kern:26011a
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
transaction within each such operation may involve multiple locking of AGF
buffer. While the freeing extent function has sorted the extents based on
AGF number before entering into transaction, however, when the file system
space is very limited, the allocation of space would try every AGF to get
space allocated, this could potentially cause out-of-order locking, thus
deadlock could happen. This fix mitigates the scarce space for allocation
by setting aside a few blocks without reservation, and avoid deadlock by
maintaining ascending order of AGF locking.
SGI-PV: 947395
SGI-Modid: xfs-linux-melb:xfs-kern:210801a
Signed-off-by: Yingping Lu <yingping@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
ATTR_NOLOCK flag, but this was split off some time ago, as ATTR_DMI needed
to be used separately. Two asserts were added to guard correctness of the
code during the transition. These are no longer required.
SGI-PV: 952145
SGI-Modid: xfs-linux-melb:xfs-kern:209633a
Signed-off-by: Olaf Weber <olaf@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
