Commit graph

304,089 commits

Author SHA1 Message Date
Ard Biesheuvel
27896c83fe r8169: default to 64-bit DMA on recent PCIe chips
The current logic around the 'use_dac' module parameter prevents the
r81969 driver from being loadable on 64-bit systems without any RAM
below 4 GB when the parameter is left at its default value.

So introduce a new default value -1 which indicates that 64-bit DMA
should be enabled on sufficiently recent PCIe chips, i.e., versions
RTL_GIGA_MAC_VER_18 or later. Explicit param values of 0 or 1 retain
the existing behavior of unconditionally enabling/disabling 64-bit DMA
on 64-bit architectures (i.e., regardless of the type and version of the
chip)

Since PCIe chips do not need to CPlusCmd Dual Address Cycle to be set,
make that conditional on the device type as well.

Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-17 14:31:09 -04:00
Alexander Graf
81003bc924 phy dp83867: Make rgmii parameters optional
If you compile without OF_MDIO support in an RGMII configuration, we fail
to configure the dp83867 phy today by writing garbage into its configuration
registers.

On the other hand if you do compile with OF_MDIO and the phy gets loaded via
device tree, you have to have the properties set in the device tree, otherwise
we fail to load the driver and don't even attach the generic phy driver to
the interface anymore.

To make things slightly more consistent, make the rgmii configuration properties
optional and allow a user to omit them in their device tree.

Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-17 14:31:09 -04:00
Alexander Graf
7f32541c2f phy dp83867: Fix compilation with CONFIG_OF_MDIO=m
When CONFIG_OF_MDIO is configured as module, the #define for it really
is CONFIG_OF_MDIO_MODULE, not CONFIG_OF_MDIO. So if we are compiling it
as module, the dp83867 doesn't see that OF_MDIO was selected and doesn't
read the dt rgmii parameters.

The fix is simple: Use IS_ENABLED(). It checks for both - module as well
as compiled in code.

Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-17 14:31:08 -04:00
David S. Miller
08a6ee5807 Merge tag 'qcom-soc-for-4.7-2' into net-next
This merges the Qualcomm SOC tree with the net-next, solving the
 merge conflict in the SMD API between the two.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJXNk3mAAoJEAsfOT8Nma3FJkEQAI/0hXy5cmACx37crT6Zishn
 +IjfnVFY0w+VWX6DdOVvAiNufMEBnvbo6jAGFxYALvZTRyt2kBxa4SgbQfgeDGp2
 UIXU5vYjYamggBALcDc9b6xBxxYEdIjGpqueIrGPyLzuAHxC74Ss4a1UYE8kC8R4
 lznB+BCuyv4WQL5GgWK2vTcFH6BD9Yw6FARLI2YJaR1oRrvl+3WCnPSKZUYPi31R
 vxvGYV5yiZ5YyOyZX4VHpn2vk1+dD7mhzXS/X1cGdV3Ysaqdw3bXqM0C31HW29F5
 qxnVNtbnoNMIpQQaFRMT00x7yx+12gCXXgb7Q1CDzvXFQXkGvQRlcHagmvi7dqI9
 YrttwbmS9LgezzEuaUTNfOJpMS9x7ghSayzHEmVLn9/7IMxdmqUiu5f9uKMjQHsW
 D3hWCTahVXf9Y+UWKOEtvnazyEcdQIuuBEzZQw05cl8OntGk1eWtHLikZVyW+zWO
 lgWX2n84Bc3BPz6o0Nu+tW4WbTlo5irnA8YLeBRJNUFgwlwlhm0Io2Q7aVhW27jZ
 rDPfil1KduOGgf0T2EMD9XdQf0tXMaJ7y7vzuGtaWy83kYaEDzYOmnLK39LQYlxm
 yYoU5Yo9fsoFXTvLyD/3FBD8Wqblv5C8ObIB4Lc3uhmrLBYA2mjFAmsxqDV2Giuz
 So/uZlqnJauYFnMBAHUu
 =UpGH
 -----END PGP SIGNATURE-----

Merge tag 'net-next-qcom-soc-4.7-2-merge' of git://github.com/andersson/kernel

Merge tag 'qcom-soc-for-4.7-2' into net-next

This merges the Qualcomm SOC tree with the net-next, solving the
merge conflict in the SMD API between the two.
2016-05-17 14:11:19 -04:00
John Stultz
cd9e2e5d3f asix: Fix offset calculation in asix_rx_fixup() causing slow transmissions
In testing with HiKey, we found that since
commit 3f30b158eb ("asix: On RX avoid creating bad Ethernet
frames"),
we're seeing lots of noise during network transfers:

[  239.027993] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[  239.037310] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x54ebb5ec, offset 4
[  239.045519] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xcdffe7a2, offset 4
[  239.275044] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[  239.284355] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x1d36f59d, offset 4
[  239.292541] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xaef3c1e9, offset 4
[  239.518996] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[  239.528300] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x2881912, offset 4
[  239.536413] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x5638f7e2, offset 4

And network throughput ends up being pretty bursty and slow with
a overall throughput of at best ~30kB/s (where as previously we
got 1.1MB/s with the slower USB1.1 "full speed" host).

We found the issue also was reproducible on a x86_64 system,
using a "high-speed" USB2.0 port but the throughput did not
measurably drop (possibly due to the scp transfer being cpu
bound on my slow test hardware).

After lots of debugging, I found the check added in the
problematic commit seems to be calculating the offset
incorrectly.

In the normal case, in the main loop of the function, we do:
(where offset is zero, or set to "offset += (copy_length + 1) &
0xfffe" in the previous loop)
    rx->header = get_unaligned_le32(skb->data +
                                    offset);
    offset += sizeof(u32);

But the problematic patch calculates:
    offset = ((rx->remaining + 1) & 0xfffe) + sizeof(u32);
    rx->header = get_unaligned_le32(skb->data + offset);

Adding some debug logic to check those offset calculation used
to find rx->header, the one in problematic code is always too
large by sizeof(u32).

Thus, this patch removes the incorrect " + sizeof(u32)" addition
in the problematic calculation, and resolves the issue.

Cc: Dean Jenkins <Dean_Jenkins@mentor.com>
Cc: "David B. Robins" <linux@davidrobins.net>
Cc: Mark Craske <Mark_Craske@mentor.com>
Cc: Emil Goode <emilgoode@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: stable <stable@vger.kernel.org> #4.4+
Reported-by: Yongqin Liu <yongqin.liu@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-17 14:02:33 -04:00
Jiri Pirko
da4ed55165 switchdev: pass pointer to fib_info instead of copy
The problem is that fib_info->nh is [0] so the struct fib_info
allocation size depends on number of nexthops. If we just copy fib_info,
we do not copy the nexthops info and driver accesses memory which is not
ours.

Given the fact that fib4 does not defer operations and therefore it does
not need copy, just pass the pointer down to drivers as it was done
before.

Fixes: 850d0cbc91 ("switchdev: remove pointers from switchdev objects")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-17 13:58:49 -04:00
Harvey Hunt
3274940bd3 drivers: net: Don't print unpopulated net_device name
For ethernet devices, net_device.name will be eth%d before
register_netdev() is called. Don't print the net_device name until
the format string is replaced.

Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: Marcel Ziswiler <marcel@ziswiler.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Barry Song <Baohua.Song@csr.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-17 12:30:19 -04:00
Sudarsana Reddy Kalluru
39651abd28 qed: add support for dcbx.
This patch adds the necessary driver support for Management Firmware to
configure the device/firmware with the dcbx results. Management Firmware
is responsible for communicating the DCBX and driving the negotiation,
but the driver has responsibility of receiving async notification and
configuring the results in hw/fw. This patch also adds the dcbx support for
future protocols (e.g., FCoE) as preparation to their imminent submission.

Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-17 12:29:34 -04:00
Geert Uytterhoeven
ccf928249c ravb: Add missing free_irq() calls to ravb_close()
When reopening the network device on ra7795/salvator-x, e.g. after a
DHCP timeout:

    IP-Config: Reopening network devices...
    genirq: Flags mismatch irq 139. 00000000 (eth0:ch0:rx_be) vs. 00000000 (ravb e6800000.ethernet eth0: cannot request IRQ eth0:ch0:rx_be
    IP-Config: Failed to open eth0
    IP-Config: No network devices available

The "mismatch" is due to requesting an IRQ that is already in use,
while IRQF_PROBE_SHARED wasn't set.

However, the real cause is that ravb_close() doesn't release any of the
R-Car Gen3-specific secondary IRQs.

Add the missing free_irq() calls to fix this.

Fixes: f51bdc236b ("ravb: Add dma queue interrupt support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-17 12:26:56 -04:00
Dan Carpenter
f82731b454 qed: Remove a stray tab
This line was indented more than it should be.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-17 12:23:37 -04:00
David S. Miller
2cc632dbc7 Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2016-05-16

This series contains 2 fixes to ixgbe only.

Emil fixes transmit hangs when enabling SRIOV by swapping the parameters
in GENMASK in order to generate the correct mask.

Alex fixes his previous patch b83e30104b ("ixgbe/ixgbevf: Add support
for GSO partial") where he somehow transposed the location of setting
the VLAN features in netdev->features and the configuration of the
vlan_features.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-17 12:18:27 -04:00
Philippe Reynes
b172542373 net: ethernet: fec-mpc52xx: use phy_ethtool_{get|set}_link_ksettings
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 22:20:06 -04:00
Philippe Reynes
a54d20f85a net: ethernet: fec-mpc52xx: use phydev from struct net_device
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 22:20:06 -04:00
Ezequiel Garcia
a8df35d458 stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is set
Commit f748be531d ("stmmac: support new GMAC4") reverted a previous fix
by mistake. This commit re-applies said fix:

  commit dec2165ff3
  Author: Sonic Zhang <sonic.zhang@analog.com>
  Date:   Thu Jan 22 14:55:57 2015 +0800
  stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is set

  Clear the TX COE bit when force_thresh_dma_mode is set even hardware
  dma capability says support.

  Tested on BF609.

  Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
  Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
  Signed-off-by: David S. Miller <davem@davemloft.net>

Tested on LPC4350 Hitex board.

Fixes: f748be531d ("stmmac: support new GMAC4")
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 22:17:45 -04:00
Philippe Reynes
73d9011c1f net: ethernet: fs-enet: use phy_ethtool_{get|set}_link_ksettings
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 22:16:32 -04:00
Philippe Reynes
c1c511a275 net: ethernet: fs-enet: use phydev from struct net_device
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 22:16:32 -04:00
Philippe Reynes
fd24d72ca9 net: ethernet: ftgmac100: use phy_ethtool_{get|set}_link_ksettings
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 21:51:41 -04:00
Philippe Reynes
b3c40adcc9 net: ethernet: ftgmac100: use phydev from struct net_device
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 21:51:41 -04:00
Philippe Reynes
cd5f9bb4be net: ethernet: gianfar: use phy_ethtool_{get|set}_link_ksettings
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 21:51:40 -04:00
Philippe Reynes
4c4a6b0e8f net: ethernet: gianfar: use phydev from struct net_device
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 21:51:40 -04:00
Alexander Duyck
5eee87cd51 ixgbe: Fix VLAN features error
It looks like at some point I somehow transposed the location of setting
the VLAN features in netdev->features and the configuration of the
vlan_features.  As a result the driver is now generating a warning about
vlan_features being setup incorrectly.

This patch corrects that by placing the update of netdev->features to
include the VLAN features so that it is after the point where we write
netdev->features into netdev->vlan_features.

Fixes: b83e30104b ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-05-16 16:56:38 -07:00
Emil Tantilov
11f2b494bc ixgbe: use correct mask when enabling sriov
Swap the parameters in GENMASK in order to generate the correct mask.

This change fixes Tx hangs when enabling SRIOV.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-05-16 16:49:36 -07:00
Yuval Mintz
416cdf0635 qed: VFs gracefully accept lack of PM
VF's probe might log that it has no PM capability in its PCI configuration
space. As this is a valid configuration, silence such prints.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:59:19 -04:00
Yuval Mintz
83f34bd436 qed: Allow more than 16 VFs
In multi-function modes, PFs are currently limited to using 16 VFs -
But that limitation would also currently apply in case there's a single
PCI function exposed, where no such restriction should have existed.

This lifts the restriction for the default mode; User should be able
to start the maximum number of VFs as appear in the PCI config space.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:59:19 -04:00
Manish Chopra
079d20a673 qed: Reset link on IOV disable
PF updates its VFs' bulletin boards with link configurations whenever
the physical carrier changes or whenever hyper-user explicitly requires
some setting of the VFs link via the hypervisor's PF.

Since the bulletin board is getting cleaned as part of the IOV disable
flow on the PF side, re-enabling sriov would lead to a VF that sees the
carrier as 'down', until an event causing the PF to re-fill the bulletin
with the link configuration would occur.

To fix this we simply refelect the link state during the flows, giving
the later VFs a default reflecting the PFs link state.

Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:59:19 -04:00
Yuval Mintz
b2b897eba6 qed: Improve VF interrupt reset
During FLR flow, need to make sure HW is no longer capable of writing to
host memory as part of its interrupt mechanisms.
While we're at it, unify the logic cleaning the driver's status-blocks
into using a single API function for both PFs and VFs.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:59:18 -04:00
Yuval Mintz
b0409fa094 qed: Correct PF-sanity check
Seems like something broke in commit 1408cc1fa4 ("qed: Introduce VFs")
and the function no longer verifies that the vf is indeed a valid one.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:59:18 -04:00
Tariq Toukan
2bb07e155b net/mlx4_core: Fix access to uninitialized index
Prevent using uninitialized or negative index when handling
steering entries.

Fixes: b12d93d63c ('mlx4: Add support for promiscuous mode in the new steering model.')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:58:01 -04:00
David S. Miller
2ffd7e0356 Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:

====================
pull request: bluetooth-next 2016-05-14

Here are two more Bluetooth patches for the 4.7 kernel which we wanted
to get into net-next before the merge window opens. Please let me know
if there are any issues pulling. Thanks.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:56:37 -04:00
Akinobu Mita
c3875ca7d9 net: w5100-spi: add support to specify MAC address by device tree
This adds support to specify the MAC address by 'mac-address' or
'local-mac-address' properties in the device tree.  These are common
properties for the Ethernet controller.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:55:49 -04:00
Akinobu Mita
7d6da453ef net: w5100: increase TX timeout period
This increases TX timeout period from one second to 5 seconds which is
the default value if the driver doesn't explicitly set
net_device->watchdog_timeo.

The one second timeout is too short for W5100 with SPI interface mode
which doesn't support burst READ/WRITE processing in the SPI transfer.
If the packet is transmitted while RX packets are being received at a
very high rate, the TX transmittion work in the workqueue is delayed
and the watchdog timer is expired.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:55:49 -04:00
Akinobu Mita
d41cd5f7e2 net: w5100: fix MAC filtering for W5500
W5500 has different bit position for MAC filter in Socket n mode
register from W5100 and W5200.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:55:48 -04:00
Akinobu Mita
e9f0cd94c1 net: w5100: remove unused is_w5200()
The is_w5200() function is not used anymore by the commit which adds
the W5500 support.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:55:48 -04:00
Sergei Shtylyov
c8396d84c7 lxt: simplify lxt970_config_init()
This function declares the 'err' local variable for no good reason, get rid
of it.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:53:20 -04:00
Sergei Shtylyov
04e6233d57 lxt: simplify lxt97[01]_config_intr()
Both these functions declare the 'err' local variables for no good reason,
get rid of them.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:53:19 -04:00
Vivien Didelot
553eb54444 net: dsa: mv88e6xxx: remove bridge work
Now that the bridge code defers the switchdev port state setting, there
is no need to defer the port STP state change within the mv88e6xxx code.
Thus get rid of the driver's bridge work code.

This also fixes a race condition where the DSA layer assumes that the
bridge code already set the unbridged port's STP state to Disabled
before restoring the Forwarding state.

As a consequence, this also fixes the FDB flush for the unbridged port
which now correctly occurs during the Forwarding to Disabled transition.

Fixes: 0bc05d585d ("switchdev: allow caller to explicitly request attr_set as deferred")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:46:24 -04:00
David Ahern
b0e95ccdd7 net: vrf: protect changes to private data with rcu
One cpu can be processing packets which includes using the cached route
entries in the vrf device's private data and on another cpu the device
gets deleted which releases the routes and sets the pointers in net_vrf
to NULL. This results in datapath dereferencing a NULL pointer.

Fix by protecting access to dst's with rcu.

Fixes: 193125dbd8 ("net: Introduce VRF device driver")
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:46:24 -04:00
Amir Vadai
aad7e08d39 net/mlx5e: Hardware offloaded flower filter statistics support
Introduce support in updating statistics of offloaded TC flower
classifiers. Currently only the DROP action is supported.

Signed-off-by: Amir Vadai <amirva@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:43:51 -04:00
Amir Vadai
43a335e055 net/mlx5_core: Flow counters infrastructure
If a counter has the aging flag set when created, it is added to a list
of counters that will be queried periodically from a workqueue.  query
result and last use timestamp are cached.
add/del counter must be very efficient since thousands of such
operations might be issued in a second.
There is only a single reference to counters without aging, therefore
no need for locks.
But, counters with aging enabled are stored in a list. In order to make
code as lockless as possible, all the list manipulation and access to
hardware is done from a single context - the periodic counters query
thread.

The hardware supports multiple counters per FTE, however currently we
are using one counter for each FTE.

Signed-off-by: Amir Vadai <amirva@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:43:51 -04:00
Amir Vadai
bd5251dbf1 net/mlx5_core: Introduce flow steering destination of type counter
When adding a flow steering rule with a counter, need to supply a
destination of type MLX5_FLOW_DESTINATION_TYPE_COUNTER, with a pointer
to a struct mlx5_fc.
Also, MLX5_FLOW_CONTEXT_ACTION_COUNT bit should be set in the action.

Signed-off-by: Amir Vadai <amirva@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:43:51 -04:00
Amir Vadai
9dc0b289c4 net/mlx5_core: Firmware commands to support flow counters
Getting packet/byte statistics on flows is done through flow counters.
Implement the firmware commands to alloc, free and query flow counters.

Signed-off-by: Amir Vadai <amirva@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:43:51 -04:00
Amir Vadai
42ca502e17 net/mlx5_core: Use a macro in mlx5_command_str()
Use a macro instead of copying the OP name.

Signed-off-by: Amir Vadai <amirva@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:43:51 -04:00
Jisheng Zhang
b17d15592d net: pxa168_eth: Use dma_wmb/rmb where appropriate
Update the pxa168_eth driver to use the dma_rmb/wmb calls instead of the
full barriers in order to improve performance: reduced 97ns/39ns on
average in tx/rx path on Marvell BG4CT platform.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:39:49 -04:00
Jisheng Zhang
3ed687823c net: pxa168_eth: use {readl|writel}_relaxed instead of readl/writel
Since appropriate memory barriers are already there, use the relaxed
version to improve performance a bit.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:39:49 -04:00
Jiri Benc
8be0cfa4d3 vxlan: set mac_header correctly in GPE mode
For VXLAN-GPE, the interface is ARPHRD_NONE, thus we need to reset
mac_header after pulling the outer header.

v2: Put the code to the existing conditional block as suggested by
    Shmulik Ladkani.

Fixes: e1e5314de0 ("vxlan: implement GPE")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:37:10 -04:00
Paul Durrant
c2d09fde72 xen-netback: use hash value from the frontend
My recent patch to include/xen/interface/io/netif.h defines a new extra
info type that can be used to pass hash values between backend and guest
frontend.

This patch adds code to xen-netback to use the value in a hash extra
info fragment passed from the guest frontend in a transmit-side
(i.e. netback receive side) packet to set the skb hash accordingly.

Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:35:56 -04:00
Paul Durrant
f07f989338 xen-netback: pass hash value to the frontend
My recent patch to include/xen/interface/io/netif.h defines a new extra
info type that can be used to pass hash values between backend and guest
frontend.

This patch adds code to xen-netback to pass hash values calculated for
guest receive-side packets (i.e. netback transmit side) to the frontend.

Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:35:56 -04:00
Paul Durrant
40d8abdee8 xen-netback: add control protocol implementation
My recent patch to include/xen/interface/io/netif.h defines a new shared
ring (in addition to the rx and tx rings) for passing control messages
from a VM frontend driver to a backend driver.

A previous patch added the necessary boilerplate for mapping the control
ring from the frontend, should it be created. This patch adds
implementations for each of the defined protocol messages.

Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:35:56 -04:00
Paul Durrant
4e15ee2cb4 xen-netback: add control ring boilerplate
My recent patch to include/xen/interface/io/netif.h defines a new shared
ring (in addition to the rx and tx rings) for passing control messages
from a VM frontend driver to a backend driver.

This patch adds the necessary code to xen-netback to map this new shared
ring, should it be created by a frontend, but does not add implementations
for any of the defined protocol messages. These are added in a subsequent
patch for clarity.

Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:35:56 -04:00
Vitaly Kuznetsov
8809883482 hv_netvsc: set nvdev link after populating chn_table
Crash in netvsc_send() is observed when netvsc device is re-created on
mtu change/set channels. The crash is caused by dereferencing of NULL
channel pointer which comes from chn_table. The root cause is a mixture
of two facts:
- we set nvdev pointer in net_device_context in alloc_net_device()
  before we populate chn_table.
- we populate chn_table[0] only.

The issue could be papered over by checking channel != NULL in
netvsc_send() but populating the whole chn_table and writing the
nvdev pointer afterwards seems more appropriate.

Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16 13:26:01 -04:00