drv pointer should be "base + offset" instead of
"current + offset". This patch fixup this issue, otherwise
third and subsequent pointer will be broken
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There were some missing "ret = " assignments here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a device node for the Reduced Serial Bus (RSB)
controller and the defacto pinmux setting to the A80 dtsi.
Since there is only one possible pinmux setting for RSB, just
set it in the dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 Optimus board has a consumer IR receiver. Enable it in the DT.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A80 SoC has a consumer IR receiver, which is the same as
older SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 has a secondary pin controller. Add a device node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The main (24MHz) clock on the A80 is configurable via the PRCM address
space. The low power/speed (32kHz) clock is from an external chip, the
AC100.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds the supported PRCM clocks and reset controls to the A80 dtsi.
The DAUDIO module clocks are not supported yet.
Also update clock and reset phandles for r_uart.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The "cpus" clock is the clock for the embedded processor in the A80.
It is also part of the PRCM clock tree. This clock includes a pre-
divider on one of its inputs. For now we are using a custom clock
driver for it. In the future we may want to develop a generalized
driver for these types of clocks, which also includes the AHB clock
driver on sun[5678]i.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This file was left over from a cleanup of asm/gpio.h and has
not been used in a while. Let's just remove it now, so the
arch/arm/mach-mvebu/include/ directory can also disappear.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds support for the PRCM apbs clock gates found on the
Allwinner A80 SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When doing the initial setup both the hclk and the aclk need to be
enabled otherwise the board will simply hang. This only occurs when
building the vop driver as a module, when its built-in the initial setup
happens to run before the clock framework shuts of unused clocks
(including the aclk).
While there also switch to doing prepare and enable in one step rather
then separate steps to reduce the amount of code required.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Tested-by: Yakir Yang <ykk@rock-chips.com>
Tested-by: Romain Perier <romain.perier@gmail.com>
The group size for registers PADCFGLOCK, HOSTSW_OWN, GPI_IS,
GPI_IE, are not 24 for Broxton, Add a parameter to allow
different platform to set correct value.
Signed-off-by: Qi Zheng <qi.zheng@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When building for SH7734:
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:1: error: macro "_GP_DATA" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:2: error: '_GP_DATA' undeclared here (not in a function)
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:1: error: macro "_GP_DATA" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:1: error: macro "_GP_DATA" passed 5 arguments, but takes just 4
...
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:1: error: macro "_GP_INOUTSEL" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:53: error: '_GP_INOUTSEL' undeclared here (not in a function)
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:2: warning: initialization makes integer from pointer without a cast [enabled by default]
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:2: warning: (near initialization for '(anonymous)[0]') [enabled by default]
...
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:1: error: macro "_GP_INDT" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:47: error: '_GP_INDT' undeclared here (not in a function)
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:2: warning: initialization makes integer from pointer without a cast [enabled by default]
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:2: warning: (near initialization for '(anonymous)[0]') [enabled by default]
...
Add the missing "cfg" macro parameters to the sh7734-specific
_GP_DATA(), _GP_INOUTSEL(), and _GP_INDT() macros to fix this.
Fixes: 22768fc60a ("pinctrl: sh-pfc: Add macros defining GP ports with config flags")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The returned configs from pinconf_generic_parse_dt_config() is
duplicated from original. Make it clear it must be freed when no
longer necessary.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch implements the pte_accessible() macro, which can be used to
test whether or not a given pte is a candidate for allocation in the
TLB.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Callees of __create_mapping may decide to create section mappings if
sufficient low bits of the physical and virtual addresses they were
passed are zero. While __create_mapping rounds the virtual base address
down, it does not similarly round the physical base address down, and
hence non-zero bits in the physical address can prevent use of a section
mapping, even where a whole next-level table would be used instead.
Round down the physical base address in __create_mapping to enable all
callees to always create section mappings when such a mapping is
possible.
Cc: Laura Abbott <labbott@fedoraproject.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If a caller of __create_mapping provides a PA and VA which have
different sub-page offsets, it is not clear which offset they expect to
apply to the mapping, and is indicative of a bad caller.
In some cases, the region we wish to map may validly have a sub-page
offset in the physical and virtual addresses. For example, EFI runtime
regions have 4K granularity, yet may be mapped by a 64K page kernel. So
long as the physical and virtual offsets are the same, the region will
be mapped at the expected VAs.
Disallow calls with differing sub-page offsets, and WARN when they are
encountered, so that we can detect and fix such cases.
Cc: Laura Abbott <labbott@fedoraproject.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
CONFIG_PINCTRL_SPEAR is more suitable than CONFIG_PLAT_SPEAR
to guard the drivers/pinctrl/spear/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CONFIG_PINCTRL_MVEBU is more suitable than CONFIG_PLAT_ORION
to guard the drivers/pinctrl/mvebu/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CONFIG_PINCTRL_BERLIN is more suitable than CONFIG_ARCH_BERLIN
to guard the drivers/pinctrl/berlin/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a plan to support more pinctrl drivers for this SoC family.
Move the driver entries into a sub menu by using "menuconfig".
Also, add the missing dependency "depends on OF && MFD_SYSCON".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update the driver and binding for pm8994-mpp devices.
Cc: <devicetree@vger.kernel.org>
Cc: "Ivan T. Ivanov" <iivanov@mm-sol.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update the binding and driver for pm8994-gpio devices.
Cc: <devicetree@vger.kernel.org>
Cc: "Ivan T. Ivanov" <iivanov@mm-sol.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial pinctrl driver to support pin configuration with
pinctrl framework for msm8996.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Joonwoo Park <joonwoop@codeaurora.org>
[sboyd@codeaurora.org: Remove duplicate entries and enums]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There's currently two places where the gma500 fault handler relies
upon dev->struct_mutex:
- To protect r->mappping
- To make sure vm_insert_pfn isn't called concurrently (in which case
the 2nd thread would get an error code).
Everything else (specifically psb_gtt_pin) is already protected by
some other locks. Hence just create a new driver-private mmap_mutex
just for this function.
With this gma500 is complete dev->struct_mutex free!
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448271183-20523-21-git-send-email-daniel.vetter@ffwll.ch
Simply forgotten about this when I was doing my general cleansing of
simple gem mmap offset functions. There's nothing but core functions
called here, and they all have their own protection already.
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448271183-20523-20-git-send-email-daniel.vetter@ffwll.ch
This is init/teardown code, locking is just to appease locking checks.
And since gem create/free doesn't need this any more there's really no
reason for grabbing dev->struct_mutex.
Again important to switch obj_unref to _unlocked variants.
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1448271183-20523-19-git-send-email-daniel.vetter@ffwll.ch
It's either init code or already protected by other means. Note
that psb_gtt_pin/unpin has it's own lock, and that's really the
only piece of driver private state - all the modeset state is
protected with modeset locks already.
The only important bit is to switch all gem_obj_unref calls to the
_unlocked variant.
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1448271183-20523-18-git-send-email-daniel.vetter@ffwll.ch
This is called without dev->struct_mutex held, we need to use the
_unlocked variant.
Never caught in the wild since you'd need an evil userspace which
races a gem_close ioctl call with the in-progress open.
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1448271183-20523-17-git-send-email-daniel.vetter@ffwll.ch
The number of interrupts is always equal to the number of pins
provided by the PMIC gpio and MPP hardware blocks. Count the
number of irqs to figure out the number of pins instead of adding
more compatible strings or doing math on the reg property. This
should make the code more generic and ease the number of changes
we have to make to the driver for each new pmic revision.
Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Reviewed-by: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver doesn't report an error message if the ACPI tables are missing
the num-gpios property (which indicates how many GPIOs there are on this
SOC), and it didn't check to ensure that the mallocs didn't fail.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-IDI-48 family of PC/104 utility boards feature 48
individually optically isolated digital inputs. Enabled inputs feature
change-of-state detection capability; if change-of-state detection is
enabled, an interrupt is fired off if a change of input level
(low-to-high or high-to-low) is detected. Change-of-state IRQs are
enabled/disabled on 8-bit boundaries, for a total of six boundaries.
This driver provides GPIO and IRQ support for these 48 channels of
digital input. The base port address for the device may be configured
via the idi_48_base module parameter. The interrupt line number for the
device may be configured via the idi_48_irq module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have relied upon the sole caller (wait_ioctl) validating the timeout
argument. However, when waiting for multiple requests I forgot to ensure
that the timeout was still positive on the later requests. This is more
simply done inside __i915_wait_request.
Fixes regression introduced in
commit b47161858b
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Apr 27 13:41:17 2015 +0100
drm/i915: Implement inter-engine read-read optimisations
The impact of the regression is 1 jiffie for each extra active ring for
a wait_ioctl with a timeout -- I don't think anyone has noticed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1448544702-5594-1-git-send-email-chris@chris-wilson.co.uk
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Similar to
commit 37ca8d4ccd
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Oct 30 19:20:27 2015 +0200
drm/i915: Enable PCH FIFO underruns later on ILK/SNB/IVB
we can only enable fifo underrun reporting when using the fdi/lpt
after everything is set up and after a bit of waiting. The waiting
is required, enabling it right after enabling encoders will first trigger
an underrun on the pch and then, 1 frame later, an underrun on the
cpu. Two vblank waits after encoder enabling seems enough to curb it.
And similar to
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Nov 20 22:09:18 2015 +0200
drm/i915: Suppress spurious CPU FIFO underruns on ILK-IVB
we also need to make sure cpu fifo underrun reporting is disabled when
enabling the fdi rx/tx and pch transcoder&port. But somehow this is
only needed when enabling, not also when disabling.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448705139-12534-1-git-send-email-daniel.vetter@ffwll.ch
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91578
Tested-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than using drm_match_cea_mode() to see if the EDID detailed
timings are supposed to represent one of the CEA/HDMI modes, add a
special version of that function that takes in an explicit clock
tolerance value (in kHz). When looking at the detailed timings specify
the tolerance as 5kHz due to the 10kHz clock resolution limit inherent
in detailed timings.
drm_match_cea_mode() uses the normal KHZ2PICOS() matching of clocks,
which only allows smaller errors for lower clocks (eg. for 25200 it
won't allow any error) and a bigger error for higher clocks (eg. for
297000 it actually matches 296913-297000). So it doesn't really match
what we want for the fixup. Using the explicit +-5kHz is much better
for this use case.
Not sure if we should change the normal mode matching to also use
something else besides KHZ2PICOS() since it allows a different
proportion of error depending on the clock. I believe VESA CVT
allows a maximum deviation of .5%, so using that for normal mode
matching might be a good idea?
Cc: Adam Jackson <ajax@redhat.com>
Tested-by: nathan.d.ciobanu@linux.intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92217
Fixes: fa3a7340ea ("drm/edid: Fix up clock for CEA/HDMI modes specified via detailed timings")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The sh73a0 has 4 MSIOF devices, located in the A3SP power area.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The 4 MSIOF clocks are MSTP clocks, and children of the SUB clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
CS2000 needs AUDIO_CLKOUT as master clock which is generated
by Renesas sound, and Renesas sound needs CS2000 as ADUIO_CLK_B.
Because of this relationship, it will be dead-lock when driver probe.
cs2000: clk_multiplier@4f {
...
clocks = <&rcar_sound 0>, <&x12_clk>;
...
};
&rcar_sound {
...
assigned-clocks = <&cs2000>;
...
};
This patch is using dummy audio_clkout to avoid this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The numbers aren't always linear, just like in the real world.
Correct to the right numbers stated in the datasheet (although we
can't trust the datasheet as well).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some of these were waiting for various code to hit during the merge
window - others have simply shown up recently.
* Dummy - fix a bug introduced recently that stops events actually
reaching userspace.
* Lidar - return -EINVAL on getting a report of an invalid reading from
the device. This could mean that nothing is in range, or something
else has gone wrong. Basically it tells us nothing useful beyond the
reading is bogus and should be ignored.
* apds9660 - make sure to call pm_runtime_mark_last_busy when reading
from the device to avoid a premature disabling of the power.
* core - fix up a few missues of the WARN macro.
* spmi-vadc - fix a missing of_node_put when breaking out of
a for_each_available_child_of_node loop.
The dummy driver is going to result in a slightly interesting
merge when this meets the togreg branch as that driver has graduated
from staging in the meantime. I'll send an email in reply to that
pull request highlighting this as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=MrHH
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.4b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.4 cycle.
Some of these were waiting for various code to hit during the merge
window - others have simply shown up recently.
* Dummy - fix a bug introduced recently that stops events actually
reaching userspace.
* Lidar - return -EINVAL on getting a report of an invalid reading from
the device. This could mean that nothing is in range, or something
else has gone wrong. Basically it tells us nothing useful beyond the
reading is bogus and should be ignored.
* apds9660 - make sure to call pm_runtime_mark_last_busy when reading
from the device to avoid a premature disabling of the power.
* core - fix up a few missues of the WARN macro.
* spmi-vadc - fix a missing of_node_put when breaking out of
a for_each_available_child_of_node loop.
The dummy driver is going to result in a slightly interesting
merge when this meets the togreg branch as that driver has graduated
from staging in the meantime. I'll send an email in reply to that
pull request highlighting this as well.
More consolidation of our MSR available bit handling.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a boot option that strictly manages the MSR unavailable bits.
This catches kernel uses of FP/Altivec/SPE that would otherwise
corrupt user state.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The enable_kernel_*() functions leave the relevant MSR bits enabled
until we exit the kernel sometime later. Create disable versions
that wrap the kernel use of FP, Altivec VSX or SPE.
While we don't want to disable it normally for performance reasons
(MSR writes are slow), it will be used for a debug boot option that
does this and catches bad uses in other areas of the kernel.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Create helper functions to set and clear MSR bits after first
checking if they are already set. Grouping them will make it
easy to avoid the MSR writes in a subsequent optimisation.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
