Introduce the 'reset-gpios' property to describe the GPIO that connects
to the ADV7180 reset pin.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When compiling without CONFIG_SYSCTL, this warning appears:
net/ipv6/addrconf.c:99:12: error: 'ioam6_if_id_max' defined but not used [-Werror=unused-variable]
99 | static u32 ioam6_if_id_max = U16_MAX;
| ^~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Simply moving the declaration of this variable under ...
#ifdef CONFIG_SYSCTL
... with other similar variables fixes the issue.
Fixes: 9ee11f0fff ("ipv6: ioam: Data plane support for Pre-allocated Trace")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman says:
====================
nfp: flower: conntrack offload
Louis Peens says:
This series takes the preparation from previous two series
and finally creates the structures and control messages
to offload the conntrack flows to the card. First we
do a bit of refactoring in the existing functions
to make them re-usable for the conntrack implementation,
after which the control messages are compiled and
transmitted to the card. Lastly we add stats handling
for the conntrack flows.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The pre_aggregate callback isn't called in all cases before calling
aggregate. Add the missing calls so providers can rely on consistent
framework behavior.
Fixes: d3703b3e25 ("interconnect: Aggregate before setting initial bandwidth")
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20210721175432.2119-3-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Add in the logic to update flow stats. The flow stats from the nfp
is saved in the flow_pay struct, which is associated with the final
merged flow. This saves deltas however, so once read it needs to
be cleared. However the flow stats requests from the kernel is
from the other side of the chain, and a single tc flow from
the kernel can be merged into multiple other tc flows to form
multiple offloaded flows. This means that all linked flows
needs to be updated for each stats request.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the offload parts (ADD_FLOW/DEL_FLOW) calls to add and delete
the flows from the nfp.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compile the offload flow metadata and add flow_pay to the offload
table. Also add in the delete paths. This does not include actual
offloading to the card yet, this will follow soon.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combine the actions from the three different rules into one and
convert into the payload format expected by the nfp.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add in the code to compile match part of the payload that will be
sent to the firmware. This works similar to match.c does it, but
since three flows needs to be merged it iterates through all three
rules in a loop and combine the match fields to get the most strict
match as result.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This calculates the correct combined keylayers and key_layer_size
for the to-be-offloaded flow.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the action related offload functions to take in flow_rule *
as input instead of flow_cls_offload * as input. The flow_rule
parts of flow_cls_offload is the only part that is used in any
case, and this is required for more conntrack offload patches
which will follow later.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a small cleanup to pass in flow->rule to some of the compile
functions instead of extracting it every time. This is will also be
useful for conntrack patches later.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose and refactor the match compilation functions so that they
can be invoked externally. Also update the functions so they can
be called multiple times with the results OR'd together. This is
applicable for the flows-merging scenario, in which there could be
overlapped and non-conflicting match fields. This will be used
in upcoming conntrack patches. This is safe to do in the in the
single call case as well since both unmasked_data and mask_data
gets initialised to 0.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initial BW values may be used by providers to enforce floors. Zero
these values after sync-state so that providers know when to stop
enforcing them.
Fixes: b1d681d8d3 ("interconnect: Add sync state support")
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20210721175432.2119-2-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
This essentially reverts
commit 84a1074920
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Jan 24 11:36:08 2018 +0000
drm/i915: Shrink the GEM kmem_caches upon idling
mm/vmscan.c:do_shrink_slab() is a thing, if there's an issue with it
then we need to fix that there, not hand-roll our own slab shrinking
code in i915.
Also when this was added there was only one other caller of
kmem_cache_shrink (added 2005 to the acpi code). Now there's a 2nd one
outside of i915 code in a kunit test, which seems legit since that
wants to very carefully control what's in the kmem_cache. This out of
a total of over 500 calls to kmem_cache_create. This alone should have
been warning sign enough that we're doing something silly.
Noticed while reviewing a patch set from Jason to fix up some issues
in our i915_init() and i915_exit() module load/cleanup code. Now that
i915_globals.c isn't any different than normal init/exit functions, we
should convert them over to one unified table and remove
i915_globals.[hc] entirely.
v2: Improve commit message (Jason)
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721183229.4136488-1-daniel.vetter@ffwll.ch
When these are not referenced, gcc prints a harmless warning:
drivers/phy/tegra/xusb.c:1286:12: error: 'tegra_xusb_padctl_resume_noirq' defined but not used [-Werror=unused-function]
1286 | static int tegra_xusb_padctl_resume_noirq(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/phy/tegra/xusb.c:1276:12: error: 'tegra_xusb_padctl_suspend_noirq' defined but not used [-Werror=unused-function]
1276 | static int tegra_xusb_padctl_suspend_noirq(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: c545a90567 ("phy: tegra: xusb: Add sleepwalk and suspend/resume")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210721152550.2976003-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A copy paste error was snuck into the patch going upstream that made the
SC8180x PCIe PHY use the SM8250 serdes table, but while this works
there's some differences in the tables (and the SC8180x was left
dangling). So correct the SC8180x definition to use the SC8180x serdes
table.
Fixes: f839f14e24 ("phy: qcom-qmp: Add sc8180x PCIe support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210721163029.2813497-1-bjorn.andersson@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Test if we actually can send/receive packets with MTU size. This kind of
issue was detected on ASIX HW with bogus EEPROM.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
asix_get_phyid() is used for two reasons here. To print debug message
with the PHY ID and to wait until the PHY is powered up.
After migrating to the phylib, we can read PHYID from sysfs. If polling
for the PHY is really needed, then we will need to handle it in the
phylib as well.
This change was tested with:
- ax88772a + internal PHY
- ax88772b + external PHY
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 4th parameter in tc_chain_notify() should be flags rather than seq.
Let's change it back correctly.
Fixes: 32a4f5ecd7 ("net: sched: introduce chain object to uapi")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly introduced switchdev_handle_fdb_{add,del}_to_device helpers
solved a problem but introduced another one. They have a severe design
bug: they do not propagate FDB events on foreign interfaces to us, i.e.
this use case:
br0
/ \
/ \
/ \
/ \
swp0 eno0
(switchdev) (foreign)
when an address is learned on eno0, what is supposed to happen is that
this event should also be propagated towards swp0. Somehow I managed to
convince myself that this did work correctly, but obviously it does not.
The trouble with foreign interfaces is that we must reach a switchdev
net_device pointer through a foreign net_device that has no direct
upper/lower relationship with it. So we need to do exploratory searching
through the lower interfaces of the foreign net_device's bridge upper
(to reach swp0 from eno0, we must check its upper, br0, for lower
interfaces that pass the check_cb and foreign_dev_check_cb). This is
something that the previous code did not do, it just assumed that "dev"
will become a switchdev interface at some point, somehow, probably by
magic.
With this patch, assisted address learning on the CPU port works again
in DSA:
ip link add br0 type bridge
ip link set swp0 master br0
ip link set eno0 master br0
ip link set br0 up
[ 46.708929] mscc_felix 0000:00:00.5 swp0: Adding FDB entry towards eno0, addr 00:04:9f:05:f4:ab vid 0 as host address
Fixes: 8ca07176ab ("net: switchdev: introduce a fanout helper for SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE")
Reported-by: Eric Woudstra <ericwouds@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These devices has two interfaces, but only the second interface
contains the capture endpoint, thus quirk is required to delay the
registration until the second interface appears.
Tested-by: Jakub Fišer <jakub@ufiseru.cz>
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210721235605.53741-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vladimir Oltean says:
====================
Let switchdev drivers offload and unoffload bridge ports at their own convenience
This series introduces an explicit API through which switchdev drivers
mark a bridge port as offloaded or not:
- switchdev_bridge_port_offload()
- switchdev_bridge_port_unoffload()
Currently, the bridge assumes that a port is offloaded if
dev_get_port_parent_id(dev, &ppid, recurse=true) returns something, but
that is just an assumption that breaks some use cases (like a
non-offloaded LAG interface on top of a switchdev port, bridged with
other switchdev ports).
Along with some consolidation of the bridge logic to assign a "switchdev
offloading mark" to a port (now better called a "hardware domain"), this
series allows the bridge driver side to no longer impose restrictions on
that configuration.
Right now, all switchdev drivers must be modified to use the explicit
API, but more and more logic can then be placed centrally in the bridge
and therefore ease the job of a switchdev driver writer in the future.
For example, the first thing we can hook into the explicit switchdev
offloading API calls are the switchdev object and FDB replay helpers.
So far, these have only been used by DSA in "pull" mode (where the
driver must ask for them). Adding the replay helpers to other drivers
involves a lot of repetition. But by moving the helpers inside the
bridge port offload/unoffload hook points, we can move the entire replay
process to "push" mode (where the bridge provides them automatically).
The explicit switchdev offloading API will see further extensions in the
future.
The patches were split from a larger series for easier review:
https://patchwork.kernel.org/project/netdevbpf/cover/20210718214434.3938850-1-vladimir.oltean@nxp.com/
Changes in v6:
- Make the switchdev replay helpers opt-in
- Opt out of the replay helpers for mlxsw, rocker, prestera, sparx5,
cpsw, am65-cpsw
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 4f2673b3a2 ("net: bridge: add helper to replay
port and host-joined mdb entries"), DSA has introduced some bridge
helpers that replay switchdev events (FDB/MDB/VLAN additions and
deletions) that can be lost by the switchdev drivers in a variety of
circumstances:
- an IP multicast group was host-joined on the bridge itself before any
switchdev port joined the bridge, leading to the host MDB entries
missing in the hardware database.
- during the bridge creation process, the MAC address of the bridge was
added to the FDB as an entry pointing towards the bridge device
itself, but with no switchdev ports being part of the bridge yet, this
local FDB entry would remain unknown to the switchdev hardware
database.
- a VLAN/FDB/MDB was added to a bridge port that is a LAG interface,
before any switchdev port joined that LAG, leading to the hardware
database missing those entries.
- a switchdev port left a LAG that is a bridge port, while the LAG
remained part of the bridge, and all FDB/MDB/VLAN entries remained
installed in the hardware database of the switchdev port.
Also, since commit 0d2cfbd41c ("net: bridge: ignore switchdev events
for LAG ports which didn't request replay"), DSA introduced a method,
based on a const void *ctx, to ensure that two switchdev ports under the
same LAG that is a bridge port do not see the same MDB/VLAN entry being
replayed twice by the bridge, once for every bridge port that joins the
LAG.
With so many ordering corner cases being possible, it seems unreasonable
to expect a switchdev driver writer to get it right from the first try.
Therefore, now that DSA has experimented with the bridge replay helpers
for a little bit, we can move the code to the bridge driver where it is
more readily available to all switchdev drivers.
To convert the switchdev object replay helpers from "pull mode" (where
the driver asks for them) to a "push mode" (where the bridge offers them
automatically), the biggest problem is that the bridge needs to be aware
when a switchdev port joins and leaves, even when the switchdev is only
indirectly a bridge port (for example when the bridge port is a LAG
upper of the switchdev).
Luckily, we already have a hook for that, in the form of the newly
introduced switchdev_bridge_port_offload() and
switchdev_bridge_port_unoffload() calls. These offer a natural place for
hooking the object addition and deletion replays.
Extend the above 2 functions with:
- pointers to the switchdev atomic notifier (for FDB replays) and the
blocking notifier (for MDB and VLAN replays).
- the "const void *ctx" argument required for drivers to be able to
disambiguate between which port is targeted, when multiple ports are
lowers of the same LAG that is a bridge port. Most of the drivers pass
NULL to this argument, except the ones that support LAG offload and have
the proper context check already in place in the switchdev blocking
notifier handler.
Also unexport the replay helpers, since nobody except the bridge calls
them directly now.
Note that:
(a) we abuse the terminology slightly, because FDB entries are not
"switchdev objects", but we count them as objects nonetheless.
With no direct way to prove it, I think they are not modeled as
switchdev objects because those can only be installed by the bridge
to the hardware (as opposed to FDB entries which can be propagated
in the other direction too). This is merely an abuse of terms, FDB
entries are replayed too, despite not being objects.
(b) the bridge does not attempt to sync port attributes to newly joined
ports, just the countable stuff (the objects). The reason for this
is simple: no universal and symmetric way to sync and unsync them is
known. For example, VLAN filtering: what to do on unsync, disable or
leave it enabled? Similarly, STP state, ageing timer, etc etc. What
a switchdev port does when it becomes standalone again is not really
up to the bridge's competence, and the driver should deal with it.
On the other hand, replaying deletions of switchdev objects can be
seen a matter of cleanup and therefore be treated by the bridge,
hence this patch.
We make the replay helpers opt-in for drivers, because they might not
bring immediate benefits for them:
- nbp_vlan_init() is called _after_ netdev_master_upper_dev_link(),
so br_vlan_replay() should not do anything for the new drivers on
which we call it. The existing drivers where there was even a slight
possibility for there to exist a VLAN on a bridge port before they
join it are already guarded against this: mlxsw and prestera deny
joining LAG interfaces that are members of a bridge.
- br_fdb_replay() should now notify of local FDB entries, but I patched
all drivers except DSA to ignore these new entries in commit
2c4eca3ef7 ("net: bridge: switchdev: include local flag in FDB
notifications"). Driver authors can lift this restriction as they
wish, and when they do, they can also opt into the FDB replay
functionality.
- br_mdb_replay() should fix a real issue which is described in commit
4f2673b3a2 ("net: bridge: add helper to replay port and host-joined
mdb entries"). However most drivers do not offload the
SWITCHDEV_OBJ_ID_HOST_MDB to see this issue: only cpsw and am65_cpsw
offload this switchdev object, and I don't completely understand the
way in which they offload this switchdev object anyway. So I'll leave
it up to these drivers' respective maintainers to opt into
br_mdb_replay().
So most of the drivers pass NULL notifier blocks for the replay helpers,
except:
- dpaa2-switch which was already acked/regression-tested with the
helpers enabled (and there isn't much of a downside in having them)
- ocelot which already had replay logic in "pull" mode
- DSA which already had replay logic in "pull" mode
An important observation is that the drivers which don't currently
request bridge event replays don't even have the
switchdev_bridge_port_{offload,unoffload} calls placed in proper places
right now. This was done to avoid unnecessary rework for drivers which
might never even add support for this. For driver writers who wish to
add replay support, this can be used as a tentative placement guide:
https://patchwork.kernel.org/project/netdevbpf/patch/20210720134655.892334-11-vladimir.oltean@nxp.com/
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a desire to make the object and FDB replay helpers optional
when moving them inside the bridge driver. For example a certain driver
might not offload host MDBs and there is no case where the replay
helpers would be of immediate use to it.
So it would be nice if we could allow drivers to pass NULL pointers for
the atomic and blocking notifier blocks, and the replay helpers to do
nothing in that case.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On reception of an skb, the bridge checks if it was marked as 'already
forwarded in hardware' (checks if skb->offload_fwd_mark == 1), and if it
is, it assigns the source hardware domain of that skb based on the
hardware domain of the ingress port. Then during forwarding, it enforces
that the egress port must have a different hardware domain than the
ingress one (this is done in nbp_switchdev_allowed_egress).
Non-switchdev drivers don't report any physical switch id (neither
through devlink nor .ndo_get_port_parent_id), therefore the bridge
assigns them a hardware domain of 0, and packets coming from them will
always have skb->offload_fwd_mark = 0. So there aren't any restrictions.
Problems appear due to the fact that DSA would like to perform software
fallback for bonding and team interfaces that the physical switch cannot
offload.
+-- br0 ---+
/ / | \
/ / | \
/ | | bond0
/ | | / \
swp0 swp1 swp2 swp3 swp4
There, it is desirable that the presence of swp3 and swp4 under a
non-offloaded LAG does not preclude us from doing hardware bridging
beteen swp0, swp1 and swp2. The bandwidth of the CPU is often times high
enough that software bridging between {swp0,swp1,swp2} and bond0 is not
impractical.
But this creates an impossible paradox given the current way in which
port hardware domains are assigned. When the driver receives a packet
from swp0 (say, due to flooding), it must set skb->offload_fwd_mark to
something.
- If we set it to 0, then the bridge will forward it towards swp1, swp2
and bond0. But the switch has already forwarded it towards swp1 and
swp2 (not to bond0, remember, that isn't offloaded, so as far as the
switch is concerned, ports swp3 and swp4 are not looking up the FDB,
and the entire bond0 is a destination that is strictly behind the
CPU). But we don't want duplicated traffic towards swp1 and swp2, so
it's not ok to set skb->offload_fwd_mark = 0.
- If we set it to 1, then the bridge will not forward the skb towards
the ports with the same switchdev mark, i.e. not to swp1, swp2 and
bond0. Towards swp1 and swp2 that's ok, but towards bond0? It should
have forwarded the skb there.
So the real issue is that bond0 will be assigned the same hardware
domain as {swp0,swp1,swp2}, because the function that assigns hardware
domains to bridge ports, nbp_switchdev_add(), recurses through bond0's
lower interfaces until it finds something that implements devlink (calls
dev_get_port_parent_id with bool recurse = true). This is a problem
because the fact that bond0 can be offloaded by swp3 and swp4 in our
example is merely an assumption.
A solution is to give the bridge explicit hints as to what hardware
domain it should use for each port.
Currently, the bridging offload is very 'silent': a driver registers a
netdevice notifier, which is put on the netns's notifier chain, and
which sniffs around for NETDEV_CHANGEUPPER events where the upper is a
bridge, and the lower is an interface it knows about (one registered by
this driver, normally). Then, from within that notifier, it does a bunch
of stuff behind the bridge's back, without the bridge necessarily
knowing that there's somebody offloading that port. It looks like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v
call_netdevice_notifiers
|
v
dsa_slave_netdevice_event
|
v
oh, hey! it's for me!
|
v
.port_bridge_join
What we do to solve the conundrum is to be less silent, and change the
switchdev drivers to present themselves to the bridge. Something like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | hardware domain for
v | this port, and zero
dsa_slave_netdevice_event | if I got nothing.
| |
v |
oh, hey! it's for me! |
| |
v |
.port_bridge_join |
| |
+------------------------+
switchdev_bridge_port_offload(swp0, swp0)
Then stacked interfaces (like bond0 on top of swp3/swp4) would be
treated differently in DSA, depending on whether we can or cannot
offload them.
The offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | switchdev mark for
v | bond0.
dsa_slave_netdevice_event | Coincidentally (or not),
| | bond0 and swp0, swp1, swp2
v | all have the same switchdev
hmm, it's not quite for me, | mark now, since the ASIC
but my driver has already | is able to forward towards
called .port_lag_join | all these ports in hw.
for it, because I have |
a port with dp->lag_dev == bond0. |
| |
v |
.port_bridge_join |
for swp3 and swp4 |
| |
+------------------------+
switchdev_bridge_port_offload(bond0, swp3)
switchdev_bridge_port_offload(bond0, swp4)
And the non-offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge waiting:
call_netdevice_notifiers ^ huh, switchdev_bridge_port_offload
| | wasn't called, okay, I'll use a
v | hwdom of zero for this one.
dsa_slave_netdevice_event : Then packets received on swp0 will
| : not be software-forwarded towards
v : swp1, but they will towards bond0.
it's not for me, but
bond0 is an upper of swp3
and swp4, but their dp->lag_dev
is NULL because they couldn't
offload it.
Basically we can draw the conclusion that the lowers of a bridge port
can come and go, so depending on the configuration of lowers for a
bridge port, it can dynamically toggle between offloaded and unoffloaded.
Therefore, we need an equivalent switchdev_bridge_port_unoffload too.
This patch changes the way any switchdev driver interacts with the
bridge. From now on, everybody needs to call switchdev_bridge_port_offload
and switchdev_bridge_port_unoffload, otherwise the bridge will treat the
port as non-offloaded and allow software flooding to other ports from
the same ASIC.
Note that these functions lay the ground for a more complex handshake
between switchdev drivers and the bridge in the future.
For drivers that will request a replay of the switchdev objects when
they offload and unoffload a bridge port (DSA, dpaa2-switch, ocelot), we
place the call to switchdev_bridge_port_unoffload() strategically inside
the NETDEV_PRECHANGEUPPER notifier's code path, and not inside
NETDEV_CHANGEUPPER. This is because the switchdev object replay helpers
need the netdev adjacency lists to be valid, and that is only true in
NETDEV_PRECHANGEUPPER.
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch: regression
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> # ocelot-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hwdoms have only been used thus far for equality comparisons, the
bridge has used the simplest possible assignment policy; using a
counter to keep track of the last value handed out.
With the upcoming transmit offloading, we need to perform set
operations efficiently based on hwdoms, e.g. we want to answer
questions like "has this skb been forwarded to any port within this
hwdom?"
Move to a bitmap-based allocation scheme that recycles hwdoms once all
members leaves the bridge. This means that we can use a single
unsigned long to keep track of the hwdoms that have received an skb.
v1->v2: convert the typedef DECLARE_BITMAP(br_hwdom_map_t, BR_HWDOM_MAX)
into a plain unsigned long.
v2->v6: none
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change, four related - but distinct - concepts where named
offload_fwd_mark:
- skb->offload_fwd_mark: Set by the switchdev driver if the underlying
hardware has already forwarded this frame to the other ports in the
same hardware domain.
- nbp->offload_fwd_mark: An idetifier used to group ports that share
the same hardware forwarding domain.
- br->offload_fwd_mark: Counter used to make sure that unique IDs are
used in cases where a bridge contains ports from multiple hardware
domains.
- skb->cb->offload_fwd_mark: The hardware domain on which the frame
ingressed and was forwarded.
Introduce the term "hardware forwarding domain" ("hwdom") in the
bridge to denote a set of ports with the following property:
If an skb with skb->offload_fwd_mark set, is received on a port
belonging to hwdom N, that frame has already been forwarded to all
other ports in hwdom N.
By decoupling the name from "offload_fwd_mark", we can extend the
term's definition in the future - e.g. to add constraints that
describe expected egress behavior - without overloading the meaning of
"offload_fwd_mark".
- nbp->offload_fwd_mark thus becomes nbp->hwdom.
- br->offload_fwd_mark becomes br->last_hwdom.
- skb->cb->offload_fwd_mark becomes skb->cb->src_hwdom. The slight
change in naming here mandates a slight change in behavior of the
nbp_switchdev_frame_mark() function. Previously, it only set this
value in skb->cb for packets with skb->offload_fwd_mark true (ones
which were forwarded in hardware). Whereas now we always track the
incoming hwdom for all packets coming from a switchdev (even for the
packets which weren't forwarded in hardware, such as STP BPDUs, IGMP
reports etc). As all uses of skb->cb->offload_fwd_mark were already
gated behind checks of skb->offload_fwd_mark, this will not introduce
any functional change, but it paves the way for future changes where
the ingressing hwdom must be known for frames coming from a switchdev
regardless of whether they were forwarded in hardware or not
(basically, if the skb comes from a switchdev, skb->cb->src_hwdom now
always tracks which one).
A typical example where this is relevant: the switchdev has a fixed
configuration to trap STP BPDUs, but STP is not running on the bridge
and the group_fwd_mask allows them to be forwarded. Say we have this
setup:
br0
/ | \
/ | \
swp0 swp1 swp2
A BPDU comes in on swp0 and is trapped to the CPU; the driver does not
set skb->offload_fwd_mark. The bridge determines that the frame should
be forwarded to swp{1,2}. It is imperative that forward offloading is
_not_ allowed in this case, as the source hwdom is already "poisoned".
Recording the source hwdom allows this case to be handled properly.
v2->v3: added code comments
v3->v6: none
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make more room for some extra code in the NETDEV_PRECHANGEUPPER handler
by moving what already exists into a dedicated function.
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to propagate the extack argument for
dpaa2_switch_port_bridge_join to use it in a future patch, and it looks
like there is already an error message there which is currently printed
to the console. Move it over netlink so it is properly transmitted to
user space.
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broken interconnect providers might add the same node multiple times or
in multiple providers, which causes strange errors as the provider's
node list is later traversed.
Detect that a node already has an associated provider, complain and
reject the addition of the node, to aid the developer.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210625234903.1324755-1-bjorn.andersson@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The current probe/remove functions are implemented separately for each
target, but they are almost identical. Replace them with common
functions that can be used across all rpmh targets.
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210621214241.13521-1-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The Rockchip PX30 SoC has a Hantro VPU that features a decoder (VDPU2)
and an encoder (VEPU2).
Suggested-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The PX30 SoC includes both the VDPU2 and VEPU2 blocks which are similar
to the RK3399 (Hantro G1/H1 with shuffled registers).
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Given H.264 support for VDPU2 was just added, let's enable it.
For now, this is only enabled on platform that don't have
an RKVDEC core, such as RK3328.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rockchip VDPU2 core is present on RK3328, RK3326/PX30, RK3399
and others. It's similar to Hantro G1, but it's not compatible with it.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a hantro_h264_get_ref_nbr() helper function to get the reference
picture numbers. This will be used by the Rockchip VDPU2 H.264 driver.
This idea was originally proposed by Jonas Karlman in
"[RFC 09/12] media: hantro: Refactor G1 H264 code"
posted a while ago.
Link: https://lore.kernel.org/linux-media/HE1PR06MB401165F2BA0AD8A634FDFAF2ACBF0@HE1PR06MB4011.eurprd06.prod.outlook.com/
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In order to reuse these bitmaps, move this process to
struct hantro_h264_dec_hw_ctx. This will be used by
the Rockchip VDPU2 H.264 driver.
This idea was originally proposed by Jonas Karlman
in "[RFC 08/12] media: hantro: Fix H264 decoding of field encoded content"
which was posted a while ago.
Link: https://lore.kernel.org/linux-media/HE1PR06MB4011EA39133818A85768B91FACBF0@HE1PR06MB4011.eurprd06.prod.outlook.com/
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Getting the next src/dst buffer is relatively expensive
so avoid doing it multiple times.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The hantro_variant.init() function is there for platforms
to perform hardware-specific initialization, such as
clock rate bumping.
Not all platforms require it, so make it optional.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the VP8 decoders can't find a reference frame,
the driver falls back to the current output frame.
This will probably produce some undesirable results,
leading to frame corruption, but shouldn't cause
noisy warnings.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In dvb_usb_i2c_init, if i2c_add_adapter fails, it only prints an error
message, and then continues to set DVB_USB_STATE_I2C. This affects the
logic of dvb_usb_i2c_exit, which leads to that, the deletion of i2c_adap
even if the i2c_add_adapter fails.
Fix this by returning at the failure of i2c_add_adapter and then move
dvb_usb_i2c_exit out of the error handling code of dvb_usb_i2c_init.
Fixes: 13a79f14ab ("media: dvb-usb: Fix memory leak at error in dvb_usb_device_init()")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If vp702x_usb_in_op fails, the mac address is not initialized.
And vp702x_read_mac_addr does not handle this failure, which leads to
the uninit-value in dvb_usb_adapter_dvb_init.
Fix this by handling the failure of vp702x_usb_in_op.
Fixes: 786baecfe7 ("[media] dvb-usb: move it to drivers/media/usb/dvb-usb")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This has been tested by probing a module that contains each of the
flavors of branches we have.
Signed-off-by: Chen Lifu <chenlifu@huawei.com>
[Palmer: commit message, fix kconfig errors]
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
This has been tested by probing a module that contains an auipc
instruction.
Signed-off-by: Chen Lifu <chenlifu@huawei.com>
[Palmer: commit message]
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
If dibusb_read_eeprom_byte fails, the mac address is not initialized.
And nova_t_read_mac_address does not handle this failure, which leads to
the uninit-value in dvb_usb_adapter_dvb_init.
Fix this by handling the failure of dibusb_read_eeprom_byte.
Reported-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com
Fixes: 786baecfe7 ("[media] dvb-usb: move it to drivers/media/usb/dvb-usb")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The s_learning_mode() function is called in response to the ioctl
LIRC_SET_WIDEBAND_RECEIVER, so rename it to s_wideband_receiver().
Learning mode is when both the wideband receiver is turned on and
carrier reports are enabled.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>