Commit graph

1,044,825 commits

Author SHA1 Message Date
Lorenzo Bianconi
ffce39bfb6 mt76: mt7615: remove useless if condition in mt7615_add_interface()
Get rid of unnecessary if condition in mt7615_add_interface routine

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:46 +02:00
Shayne Chen
ae130bb8d4 mt76: mt7915: use mt7915_mcu_get_txpower_sku() to get per-rate txpower
Get per-rate txpower with mcu command. This is the preparation of
co-driver for the next chipset, which has different tmac power registers
but can share this same command.

Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:46 +02:00
Ryder Lee
accbcea4f3 mt76: mt7615: add .offset_tsf callback
It's much more accurate than .get_tsf + .set_tsf and switch to use
mt76_rmw to operate tsf registers.

Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:46 +02:00
Ryder Lee
1607313418 mt76: mt7915: add .offset_tsf callback
It's much more accurate than .get_tsf + .set_tsf, and switch to use
mt76_rmw to operate tsf registers.

Tested-by: Xing Song <xing.song@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:46 +02:00
Lorenzo Bianconi
01f7da4091 mt76: mt7921: reset wfsys during hw probe
This patch fixes a mcu hang during device probe on
Marvell ESPRESSObin after a hot reboot.

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:46 +02:00
Lorenzo Bianconi
d74c4b5667 mt76: mt7921: do not schedule hw reset if the device is not running
Do not schedule hw full reset if the device is not fully initialized
(e.g if the channel has not been configured yet). This patch fixes
the kernel crash reported below

[   44.440266] mt7921e 0000:01:00.0: chip reset failed
[   44.527575] Unable to handle kernel paging request at virtual address ffffffc02f3e0000
[   44.535771] Mem abort info:
[   44.538646]   ESR = 0x96000006
[   44.541792]   EC = 0x25: DABT (current EL), IL = 32 bits
[   44.547268]   SET = 0, FnV = 0
[   44.550413]   EA = 0, S1PTW = 0
[   44.553648] Data abort info:
[   44.556613]   ISV = 0, ISS = 0x00000006
[   44.560563]   CM = 0, WnR = 0
[   44.563619] swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000000955000
[   44.570530] [ffffffc02f3e0000] pgd=100000003ffff003, p4d=100000003ffff003, pud=100000003ffff003, pmd=0000000000000000
[   44.581489] Internal error: Oops: 96000006 [#1] SMP
[   44.606406] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G        W         5.13.0-rc1-espressobin-12875-g6dc7f82ebc26 #33
[   44.617264] Hardware name: Globalscale Marvell ESPRESSOBin Board (DT)
[   44.623905] pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO BTYPE=--)
[   44.630100] pc : __queue_work+0x1f0/0x500
[   44.634249] lr : __queue_work+0x1e8/0x500
[   44.638384] sp : ffffffc010003d70
[   44.641798] x29: ffffffc010003d70 x28: 0000000000000000 x27: ffffff8003989200
[   44.649166] x26: ffffffc010c08510 x25: 0000000000000002 x24: ffffffc010ad90b0
[   44.656533] x23: ffffffc010c08508 x22: 0000000000000012 x21: 0000000000000000
[   44.663899] x20: ffffff8006385238 x19: ffffffc02f3e0000 x18: 00000000000003c9
[   44.671266] x17: 0000000000000000 x16: 0000000000000000 x15: 000009b1a8a3bf90
[   44.678632] x14: 0098968000000000 x13: 0000000000000000 x12: 0000000000000325
[   44.685998] x11: ffffff803fda1928 x10: 0000000000000001 x9 : ffffffc010003e98
[   44.693365] x8 : 0000000000000032 x7 : fff8000000000000 x6 : 0000000000000035
[   44.700732] x5 : 0000000000000000 x4 : 0000000000000000 x3 : ffffffc010adf700
[   44.708098] x2 : ffffff8006385238 x1 : 000000007fffffff x0 : 0000000000000000
[   44.715465] Call trace:
[   44.717982]  __queue_work+0x1f0/0x500
[   44.721760]  delayed_work_timer_fn+0x18/0x20
[   44.726167]  call_timer_fn+0x2c/0x178
[   44.729947]  run_timer_softirq+0x488/0x5c8
[   44.734172]  _stext+0x11c/0x378
[   44.737411]  irq_exit+0x100/0x108
[   44.740830]  __handle_domain_irq+0x60/0xb0
[   44.745059]  gic_handle_irq+0x70/0x2b4
[   44.748929]  el1_irq+0xb8/0x13c
[   44.752167]  arch_cpu_idle+0x14/0x30
[   44.755858]  default_idle_call+0x38/0x168
[   44.759994]  do_idle+0x1fc/0x210
[   44.763325]  cpu_startup_entry+0x20/0x58
[   44.767372]  rest_init+0xb8/0xc8
[   44.770703]  arch_call_rest_init+0xc/0x14
[   44.774841]  start_kernel+0x408/0x424
[   44.778623] Code: aa1403e0 97fff54f aa0003f5 b5fff500 (f9400275)
[   44.784907] ---[ end trace be73c3142d8c36a9 ]---
[   44.789668] Kernel panic - not syncing: Oops: Fatal exception in interrupt

Fixes: 0c1ce98846 ("mt76: mt7921: add wifi reset support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:46 +02:00
Lorenzo Bianconi
f5e3db3013 mt76: mt7921: return proper error value in mt7921_mac_init
Return possible error values in mt7921_mac_init routine

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:46 +02:00
YN Chen
b4b880b90c mt76: connac: add bss color support for sta mode
Add bss color support for sta mode

Signed-off-by: Jayden.Kuo <jayden.kuo@mediatek.com>
Signed-off-by: YN Chen <yn.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:45 +02:00
Lorenzo Bianconi
a2d3442e3d mt76: mt7921: enable runtime pm by default
mt7921 is mainly used in CE/IoT market so enable runtime-pm by default

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:45 +02:00
Sean Wang
213f87289e mt76: mt7921: fix OMAC idx usage
OMAC idx have to be same with BSS idx according to firmware usage.

Fixes: e0f9fdda81 ("mt76: mt7921: add ieee80211_ops")
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: YN Chen <yn.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:45 +02:00
Sean Wang
f86625ae0e mt76: mt7921: fix invalid register access in wake_work
Make sure mt7921_pm_wake_work wouldn't be scheduled after the driver is
in suspend mode to fix the following the kernel crash.

[ 3515.390012] mt7921e 0000:01:00.0: calling pci_pm_suspend+0x0/0x22c @ 2869, parent: 0000:00:00.0
[ 3515.390015] mt7921e 0000:01:00.0: mt7921_pci_suspend +
[ 3515.396395] anx7625 3-0058: anx7625_suspend+0x0/0x6c returned 0 after 0 usecs
[ 3515.405965] mt7921e 0000:01:00.0: mt7921_pci_suspend -
[ 3515.411336] usb 1-1.4: usb_dev_suspend+0x0/0x2c returned 0 after 1 usecs
[ 3515.411513] SError Interrupt on CPU7, code 0xbe000011 -- SError
[ 3515.411515] CPU: 7 PID: 2849 Comm: kworker/u16:27 Not tainted 5.4.114 #44
[ 3515.411516] Hardware name: MediaTek Asurada rev1 board (DT)
[ 3515.411517] Workqueue: mt76 mt7921_pm_wake_work [mt7921e]
[ 3515.411518] pstate: 80c00009 (Nzcv daif +PAN +UAO)
[ 3515.411519] pc : mt76_mmio_rr+0x30/0xf0 [mt76]
[ 3515.411520] lr : mt7921_rr+0x38/0x44 [mt7921e]
[ 3515.411520] sp : ffffffc015813c50
[ 3515.411521] x29: ffffffc015813c50 x28: 0000000000000402
[ 3515.411522] x27: ffffffe5a2012138 x26: ffffffe5a1eea018
[ 3515.411524] x25: 00000000328be505 x24: 00000000000a0002
[ 3515.411525] x23: 0000000000000006 x22: ffffffbd29b7a300
[ 3515.411527] x21: ffffffbd29b7a300 x20: 00000000000e0010
[ 3515.411528] x19: 00000000eac08f43 x18: 0000000000000000
[ 3515.411529] x17: 0000000000000000 x16: ffffffe5a16b2914
[ 3515.411531] x15: 0000000000000010 x14: 0000000000000010
[ 3515.411532] x13: 00000000003dd3a2 x12: 0000000000010000
[ 3515.411533] x11: ffffffe597abec14 x10: 0000000000000010
[ 3515.411535] x9 : ffffffe597abeba8 x8 : ffffffc013ce0010
[ 3515.411536] x7 : 000000b2b5593519 x6 : 0000000000300000
[ 3515.411537] x5 : 0000000000000000 x4 : 0000000000000032
[ 3515.411539] x3 : 0000000000000000 x2 : 0000000000000004
[ 3515.411540] x1 : 00000000000e0010 x0 : ffffffbd29b7a300
[ 3515.411542] Kernel panic - not syncing: Asynchronous SError Interrupt
[ 3515.411543] CPU: 7 PID: 2849 Comm: kworker/u16:27 Not tainted 5.4.114 #44
[ 3515.411544] Hardware name: MediaTek Asurada rev1 board (DT)
[ 3515.411544] Workqueue: mt76 mt7921_pm_wake_work [mt7921e]
[ 3515.411545] Call trace:
[ 3515.411546]  dump_backtrace+0x0/0x14c
[ 3515.411546]  show_stack+0x20/0x2c
[ 3515.411547]  dump_stack+0xa0/0xfc
[ 3515.411548]  panic+0x154/0x350
[ 3515.411548]  panic+0x0/0x350
[ 3515.411549]  arm64_serror_panic+0x78/0x84
[ 3515.411550]  do_serror+0x0/0x118
[ 3515.411550]  do_serror+0xa4/0x118
[ 3515.411551]  el1_error+0x84/0xf8
[ 3515.411552]  mt76_mmio_rr+0x30/0xf0 [mt76]
[ 3515.411552]  mt7921_rr+0x38/0x44 [mt7921e]
[ 3515.411553]  __mt76_poll_msec+0x5c/0x9c [mt76]
[ 3515.411554]  __mt7921_mcu_drv_pmctrl+0x50/0x94 [mt7921e]
[ 3515.411555]  mt7921_mcu_drv_pmctrl+0x38/0xb0 [mt7921e]
[ 3515.411555]  mt7921_pm_wake_work+0x34/0xd4 [mt7921e]
[ 3515.411556]  process_one_work+0x208/0x3c8
[ 3515.411557]  worker_thread+0x23c/0x3e8
[ 3515.411557]  kthread+0x144/0x178
[ 3515.411558]  ret_from_fork+0x10/0x18
[ 3515.418831] SMP: stopping secondary CPUs
[ 3515.418832] Kernel Offset: 0x2590c00000 from 0xffffffc010000000
[ 3515.418832] PHYS_OFFSET: 0xffffffc400000000
[ 3515.418833] CPU features: 0x080026,2a80aa18
[ 3515.418834] Memory Limit: none
[DL] 00000000 00000000 010701

Fixes: 1d8efc741d ("mt76: mt7921: introduce Runtime PM support")
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:45 +02:00
Sean Wang
f07ac384b4 mt76: mt7921: avoid unnecessary consecutive WiFi resets
Avoid unnecessary consecutive WiFi resets by dropping reset
request when reset work is working.

Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:45 +02:00
Deren Wu
f011c3691a mt76: connac: update BA win size in Rx direction
Update BA size used data transimission in the Rx direction to improve Rx
throughput.

Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: YN Chen <yn.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:45 +02:00
Ryder Lee
109e505ad9 mt76: mt7615: add thermal sensor device support
Similar to mt7915, switching to use standard hwmon sysfs.
For reading temperature, cat /sys/class/ieee80211/phy*/hwmon*/temp1_input

Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:45 +02:00
Ryder Lee
34b877d972 mt76: mt7915: add thermal cooling device support
Thermal cooling device support is added to control the temperature by
throttling the data transmission for the given duration. Throttling is
done by adjusting Tx period by given percentage of time. The thermal
device allows user to configure duty cycle.

Throttling can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder

To set duty cycle as 80%,
echo 80 > /sys/class/ieee80211/phy*/cooling_device/cur_state

Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:45 +02:00
Ryder Lee
33fe9c639c mt76: mt7915: add thermal sensor device support
This provides userspace with a unified interface, hwmon sysfs, to monitor
temperature in the hardware and can be adapted to system monitoring tools.

For reading temperature, cat /sys/class/ieee80211/phy*/hwmon*/temp1_input

Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:45 +02:00
Sean Wang
10de032a31 mt76: mt7921: add back connection monitor support
Hw beacon cmd to the mt7921 firmware doesn't only filter out the beacon,
but also performs its own connection monitoring, including periodic
keep-alives to the AP and probing the AP on beacon loss. Will indicate
the host with the event when the firmware detects the connection is lost.

Fixes: 1d8efc741d ("mt76: mt7921: introduce Runtime PM support")
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: YN Chen <yn.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:44 +02:00
Sean Wang
edb5aebc1c mt76: mt7921: consider the invalid value for to_rssi
It is possible the RCPI from the certain antenna is an invalid value,
especially packets are receiving while the system is frequently entering
deep sleep mode, so consider calculating RSSI with the reasonable upper
bound to avoid report the wrong value to the mac80211 layer.

Fixes: 163f4d22c1 ("mt76: mt7921: add MAC support")
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:44 +02:00
YN Chen
193e5f22ee mt76: connac: fix WoW with disconnetion and bitmap pattern
Update MCU command usage to fix WoW configuration with disconnection
and bitmap pattern and to avoid magic number.

Fixes: ffa1bf9742 ("mt76: mt7921: introduce PM support")
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: YN Chen <yn.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:44 +02:00
Sean Wang
7bf0a71e83 mt76: mt7921: fix reset under the deep sleep is enabled
To fix possibly the race to access register between the WiFi reset
and the other context that is caused by explicitly cancelling ps_work
and wake_work to break PM_STATE consistency.

Deep sleep would cause the hardware into the inactive state,
so we forcely put device drv_own state before we start to reset.

The patch also ignore the reset request when the procedure is in
progress to avoid the consecutive WiFi resets.

localhost ~ # [ 2932.073966] SError Interrupt on CPU7, code 0xbe000011
[ 2932.073967] CPU: 7 PID: 8761 Comm: kworker/u16:2 Not tainted 5.4.112 #30
[ 2932.073968] Hardware name: MediaTek Asurada rev1 board (DT)
[ 2932.073968] Workqueue: phy0 ieee80211_reconfig_filter [mac80211]
[ 2932.073969] pstate: 80400089 (Nzcv daIf +PAN -UAO)
[ 2932.073969] pc : el1_irq+0x78/0x180
[ 2932.073970] lr : mt76_mmio_rmw+0x30/0x5c [mt76]
[ 2932.073970] sp : ffffffc01142bad0
[ 2932.073970] x29: ffffffc01142bc00 x28: ffffff8f96fb1e00
[ 2932.073971] x27: ffffffd2cdc12138 x26: ffffffd2cdaeb018
[ 2932.073972] x25: 0000000000000000 x24: ffffff8fa8e14c08
[ 2932.073973] x23: 0000000080c00009 x22: ffffffd2a5603918
[ 2932.073974] x21: ffffffc01142bc10 x20: 0000007fffffffff
[ 2932.073975] x19: 0000000000000000 x18: 0000000000000400
[ 2932.073975] x17: 0000000000000400 x16: ffffffd2cd2b87dc
[ 2932.073976] x15: 0000000000000000 x14: 0000000000000000
[ 2932.073977] x13: 0000000000000001 x12: 0000000000000001
[ 2932.073978] x11: 0000000000000001 x10: 000000000010e000
[ 2932.073978] x9 : 0000000000000000 x8 : ffffffc013921404
[ 2932.073979] x7 : 000000b2b5593519 x6 : 0000000000300000
[ 2932.073980] x5 : 0000000000000000 x4 : ffffffc01142bbc8
[ 2932.073980] x3 : 00000000000001f0 x2 : 0000000000000000
[ 2932.073981] x1 : 0000000000021404 x0 : ffffff8fa8e12300
[ 2932.073982] Kernel panic - not syncing: Asynchronous SError Interrupt
[ 2932.073983] CPU: 7 PID: 8761 Comm: kworker/u16:2 Not tainted 5.4.112 #30
[ 2932.073983] Hardware name: MediaTek Asurada rev1 board (DT)
[ 2932.073984] Workqueue: phy0 ieee80211_reconfig_filter [mac80211]
[ 2932.073984] Call trace:
[ 2932.073985]  dump_backtrace+0x0/0x14c
[ 2932.073985]  show_stack+0x20/0x2c
[ 2932.073985]  dump_stack+0xa0/0xf8
[ 2932.073986]  panic+0x154/0x360
[ 2932.073986]  test_taint+0x0/0x44
[ 2932.073986]  arm64_serror_panic+0x78/0x84
[ 2932.073987]  do_serror+0x0/0x118
[ 2932.073987]  do_serror+0xa4/0x118
[ 2932.073987]  el1_error+0x84/0xf8
[ 2932.073988]  el1_irq+0x78/0x180
[ 2932.073988]  mt76_mmio_rr+0x30/0xf0 [mt76]
[ 2932.073988]  mt76_mmio_rmw+0x30/0x5c [mt76]
[ 2932.073989]  mt7921_rmw+0x4c/0x5c [mt7921e]
[ 2932.073989]  mt7921_configure_filter+0x138/0x160 [mt7921e]
[ 2932.073990]  ieee80211_configure_filter+0x2f0/0x3e0 [mac80211]
[ 2932.073990]  ieee80211_reconfig_filter+0x1c/0x28 [mac80211]
[ 2932.073990]  process_one_work+0x208/0x3c8
[ 2932.073991]  worker_thread+0x23c/0x3e8
[ 2932.073991]  kthread+0x140/0x17c
[ 2932.073992]  ret_from_fork+0x10/0x18
[ 2932.074071] SMP: stopping secondary CPUs
[ 2932.074071] Kernel Offset: 0x12bc800000 from 0xffffffc010000000
[ 2932.074072] PHYS_OFFSET: 0xfffffff180000000
[ 2932.074072] CPU features: 0x080026,2a80aa18
[ 2932.074072] Memory Limit: none

Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:44 +02:00
Sean Wang
4bfa291251 mt76: connac: fw_own rely on all packet memory all being free
If the device is MMIO-based, we must ensure all TxD/TxP on the host
memory all being consumed by the device prior to safely switching to
fw_own state.

Fixes: ec7bd7b4a9 ("mt76: connac: check wake refcount in mcu_fw_pmctrl")
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:44 +02:00
Sean Wang
2c80c02a68 mt76: mt7921: Don't alter Rx path classifier
Keep Rx path classifier the mt7921 firmware prefers to allow frames pass
through MCU.

Fixes: 5c14a5f944 ("mt76: mt7921: introduce mt7921e support")
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:44 +02:00
Sean Wang
20eb83c749 mt76: mt7921: fix mt7921_wfsys_reset sequence
WiFi subsytem reset should control MT_WFSYS_SW_RST_B and then poll the
same register until the bit WFSYS_SW_INIT_DONE bit is set.

Fixes: 0c1ce98846 ("mt76: mt7921: add wifi reset support")
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:44 +02:00
Lorenzo Bianconi
54c31b9e65 mt76: mt7663: enable hw rx header translation
As already done for mt7615 and mt7915, enable rx header translation
offload for mt7663 in order to reduce cpu load in the rx path.

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:44 +02:00
Lorenzo Bianconi
2f83054342 mt76: mt7615: free irq if mt7615_mmio_probe fails
As already done for mt7915 and mt7921, free registered irq line if
mt7615_mmio_probe routine fails

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:44 +02:00
Lorenzo Bianconi
47cbf73cf9 mt76: mt76x0: use dev_debug instead of dev_err for hw_rf_ctrl
BIT(0) in MT_EE_NIC_CONF_1 is use to notify the driver if the radio RF
switch is controlled through a gpio. Use dev_debug instead of dev_err
to log this info.

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:44 +02:00
Lorenzo Bianconi
8d3cdc1bbb mt76: mt7615: fix NULL pointer dereference in tx_prepare_skb()
Fix theoretical NULL pointer dereference in mt7615_tx_prepare_skb and
mt7663_usb_sdio_tx_prepare_skb routines. This issue has been identified
by code analysis.

Fixes: 6aa4ed7927 ("mt76: mt7615: implement DMA support for MT7622")
Fixes: 4bb586bc33 ("mt76: mt7663u: sync probe sampling with rate configuration")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:43 +02:00
Lorenzo Bianconi
d7400a2f3e mt76: fix possible NULL pointer dereference in mt76_tx
Even if this is not a real issue since mt76_tx is never run with wcid set
to NULL, fix a theoretical NULL pointer dereference in mt76_tx routine

Fixes: db9f11d343 ("mt76: store wcid tx rate info in one u32 reduce locking")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:43 +02:00
Ryder Lee
76be6c076c mt76: mt7915: add .set_bitrate_mask() callback
Add runtime configuration for bitrate mask. This update firmware rate
control to add a boundary on top of table to limit the rate selection
for each peer, so when user set bitrates vht-mcs-5 1:9, which actually
means nss = 1 mcs = 0~9. This only applies to data frames as for other
mgmt, mcast, bcast still use legacy rates as it is.

Note that driver does not support GI configuration.

Example:
iw dev wlan0 set bitrates vht-mcs-5 1:9 he-mcs-5 2:7
iw dev wlan0 set bitrates legacy-5 6 he-mcs-5 2:0-11

Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:43 +02:00
Ryder Lee
a441a77a73 mt76: mt7915: cleanup mt7915_mcu_sta_rate_ctrl_tlv()
Remove obsoleted codes. This is the preparation for .set_bitrate_mask().

Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:43 +02:00
Lorenzo Bianconi
0e75732764 mt76: mt7921: enable rx csum offload
As already done for mt7615 and mt7915, enable hw rx checksum offload.

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:43 +02:00
Lorenzo Bianconi
24299fc869 mt76: mt7921: enable rx header traslation offload
As already done for mt7615 and mt7915, enable rx header translation
offload for mt7921 in order to reduce cpu load in the rx path.

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:43 +02:00
Lorenzo Bianconi
868fe07ee6 mt76: connac: add missing configuration in mt76_connac_mcu_wtbl_hdr_trans_tlv
Add missing configuration parameters in mt76_connac_mcu_wtbl_hdr_trans_tlv
routine

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:43 +02:00
Lorenzo Bianconi
5b0b5c6a1c mt76: mt7921: enable rx hw de-amsdu
Enable hw rx-amsdu de-aggregation support available in 7921 devices.
This is a preliminary patch to enable rx checksum offload.

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:43 +02:00
Dan Carpenter
861fad474e mt76: mt7915: fix a signedness bug in mt7915_mcu_apply_tx_dpd()
"idx" needs to be signed for the error handling to work.

Fixes: 495184ac91 ("mt76: mt7915: add support for applying pre-calibration data")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:43 +02:00
Evelyn Tsai
64cf5ad3c2 mt76: mt7915: fix tssi indication field of DBDC NICs
Correct the bitfield which indicates TSSI on/off for MT7915D NIC.

Signed-off-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:42 +02:00
Lorenzo Bianconi
54b8fdebe4 mt76: move mt76_rates in mt76 module
Move mt76_rates array in mt76 module and remove duplicated code since it
is shared by all drivers

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 09:22:37 +02:00
David Abdurachmanov
7ede12b01b
riscv: dts: fu740: fix cache-controller interrupts
The order of interrupt numbers is incorrect.

The order for FU740 is: DirError, DataError, DataFail, DirFail

From SiFive FU740-C000 Manual:
19 - L2 Cache DirError
20 - L2 Cache DirFail
21 - L2 Cache DataError
22 - L2 Cache DataFail

Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
2021-06-19 00:11:53 -07:00
Geert Uytterhoeven
aaf3589966 dt-bindings: input: touchscreen: st1232: Convert to json-schema
Convert the Sitronix st1232/st1633 touchscreen controller Device Tree
binding documentation to json-schema.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Martin Kepplinger <martink@posteo.de>
Link: https://lore.kernel.org/r/fbba650cff07780c28ad6dd8dbef5cc1451b7762.1623418065.git.geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-06-18 21:28:23 -07:00
Tyson Moore
c2d7ed9d68 Input: i8042 - fix typos in comments
This trivial patch fixes two spelling typos in i8042.c:

- 'i8042_unlock_ship()' to 'i8042_unlock_chip()'
- 'i8042_controller init' to 'i8042_controller_init'

Signed-off-by: Tyson Moore <tyson@tyson.me>
Link: https://lore.kernel.org/r/20210612060753.28968-1-tyson@tyson.me
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-06-18 21:28:22 -07:00
Oleh Kravchenko
552e4047f3 Input: add SparkFun Qwiic Joystick driver
A simple analog joystick built on Low Power ATtiny85 Microcontroller.
Directional movements are measured with two 10 kΩ potentiometers
connected with a gimbal mechanism that separates the horizontal and
vertical movements. This joystick also has a select button that is actuated
when the joystick is pressed down.

Input events polled over the I2C bus.

Product page:
https://www.sparkfun.com/products/15168
Firmware and hardware sources:
https://github.com/sparkfun/Qwiic_Joystick

Tested on RPi4B and O4-iMX-NANO boards.

Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Reviewed-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210608223130.16830-2-oleg@kaa.org.ua
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-06-18 21:28:20 -07:00
Oleh Kravchenko
9b2336965a dt-bindings: Add vendor prefix and bindings for Qwiic Joystick
Add vendor prefix for SparkFun Electronics.
Update trivial-devices.yaml with SparkFun Qwiic Joystick description.

Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210608223130.16830-1-oleg@kaa.org.ua
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-06-18 21:28:18 -07:00
Jisheng Zhang
3a02764c37
riscv: Ensure BPF_JIT_REGION_START aligned with PMD size
Andreas reported commit fc8504765e ("riscv: bpf: Avoid breaking W^X")
breaks booting with one kind of defconfig, I reproduced a kernel panic
with the defconfig:

[    0.138553] Unable to handle kernel paging request at virtual address ffffffff81201220
[    0.139159] Oops [#1]
[    0.139303] Modules linked in:
[    0.139601] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-rc5-default+ #1
[    0.139934] Hardware name: riscv-virtio,qemu (DT)
[    0.140193] epc : __memset+0xc4/0xfc
[    0.140416]  ra : skb_flow_dissector_init+0x1e/0x82
[    0.140609] epc : ffffffff8029806c ra : ffffffff8033be78 sp : ffffffe001647da0
[    0.140878]  gp : ffffffff81134b08 tp : ffffffe001654380 t0 : ffffffff81201158
[    0.141156]  t1 : 0000000000000002 t2 : 0000000000000154 s0 : ffffffe001647dd0
[    0.141424]  s1 : ffffffff80a43250 a0 : ffffffff81201220 a1 : 0000000000000000
[    0.141654]  a2 : 000000000000003c a3 : ffffffff81201258 a4 : 0000000000000064
[    0.141893]  a5 : ffffffff8029806c a6 : 0000000000000040 a7 : ffffffffffffffff
[    0.142126]  s2 : ffffffff81201220 s3 : 0000000000000009 s4 : ffffffff81135088
[    0.142353]  s5 : ffffffff81135038 s6 : ffffffff8080ce80 s7 : ffffffff80800438
[    0.142584]  s8 : ffffffff80bc6578 s9 : 0000000000000008 s10: ffffffff806000ac
[    0.142810]  s11: 0000000000000000 t3 : fffffffffffffffc t4 : 0000000000000000
[    0.143042]  t5 : 0000000000000155 t6 : 00000000000003ff
[    0.143220] status: 0000000000000120 badaddr: ffffffff81201220 cause: 000000000000000f
[    0.143560] [<ffffffff8029806c>] __memset+0xc4/0xfc
[    0.143859] [<ffffffff8061e984>] init_default_flow_dissectors+0x22/0x60
[    0.144092] [<ffffffff800010fc>] do_one_initcall+0x3e/0x168
[    0.144278] [<ffffffff80600df0>] kernel_init_freeable+0x1c8/0x224
[    0.144479] [<ffffffff804868a8>] kernel_init+0x12/0x110
[    0.144658] [<ffffffff800022de>] ret_from_exception+0x0/0xc
[    0.145124] ---[ end trace f1e9643daa46d591 ]---

After some investigation, I think I found the root cause: commit
2bfc6cd81b ("move kernel mapping outside of linear mapping") moves
BPF JIT region after the kernel:

| #define BPF_JIT_REGION_START	PFN_ALIGN((unsigned long)&_end)

The &_end is unlikely aligned with PMD size, so the front bpf jit
region sits with part of kernel .data section in one PMD size mapping.
But kernel is mapped in PMD SIZE, when bpf_jit_binary_lock_ro() is
called to make the first bpf jit prog ROX, we will make part of kernel
.data section RO too, so when we write to, for example memset the
.data section, MMU will trigger a store page fault.

To fix the issue, we need to ensure the BPF JIT region is PMD size
aligned. This patch acchieve this goal by restoring the BPF JIT region
to original position, I.E the 128MB before kernel .text section. The
modification to kasan_init.c is inspired by Alexandre.

Fixes: fc8504765e ("riscv: bpf: Avoid breaking W^X")
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
2021-06-18 21:10:05 -07:00
Jisheng Zhang
314b781706
riscv: kasan: Fix MODULES_VADDR evaluation due to local variables' name
commit 2bfc6cd81b ("riscv: Move kernel mapping outside of linear
mapping") makes use of MODULES_VADDR to populate kernel, BPF, modules
mapping. Currently, MODULES_VADDR is defined as below for RV64:

| #define MODULES_VADDR   (PFN_ALIGN((unsigned long)&_end) - SZ_2G)

But kasan_init() has two local variables which are also named as _start,
_end, so MODULES_VADDR is evaluated with the local variable _end
rather than the global "_end" as we expected. Fix this issue by
renaming the two local variables.

Fixes: 2bfc6cd81b ("riscv: Move kernel mapping outside of linear mapping")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
2021-06-18 21:09:56 -07:00
Kees Cook
041761f4a4 scsi: aha1740: Avoid over-read of sense buffer
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.

SCtmp->sense_buffer is 96 bytes, but ecbptr->sense is 14 bytes. Instead of
over-reading ecbptr->sense, copy only the actual contents and zero pad the
remaining bytes, avoiding potential over-reads.

Link: https://lore.kernel.org/r/20210616212437.1727088-1-keescook@chromium.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-06-18 23:27:04 -04:00
Kees Cook
86a6a0bdbe scsi: arcmsr: Avoid over-read of sense buffer
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.

pcmd->sense_buffer is 96 bytes, and was being manually zero-filled.
However, struct SENSE_DATA is 18 bytes, with ccb->arcmsr_cdb.SenseData only
being 15 bytes, resulting in a 3 byte over-read.

Copy only the contents of ccb->arcmsr_cdb.SenseData and zero fill the
remainder, avoiding potential over-reads.

Link: https://lore.kernel.org/r/20210616212428.1726958-1-keescook@chromium.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-06-18 23:26:33 -04:00
Kees Cook
4ab293c280 scsi: ips: Avoid over-read of sense buffer
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy() avoid intentionally reading across
neighboring array fields.

scb->scsi_cmd->sense_buffer is 96 bytes:
	#define SCSI_SENSE_BUFFERSIZE        96

tapeDCDB->sense_info is 56 bytes:
	typedef struct {
	   ...
	   uint8_t   sense_info[56];
	} IPS_DCDB_TABLE_TAPE, ...

scb->dcdb.sense_info is 64 bytes:
	typedef struct {
	   ...
	   uint8_t   sense_info[64];
	   ...
	} IPS_DCDB_TABLE, ...

Copying 96 bytes from either was copying beyond the end of the respective
buffers, leading to potential memory content exposures. Correctly copy the
actual buffer contents and zero pad the remaining bytes.

Link: https://lore.kernel.org/r/20210616212408.1726812-1-keescook@chromium.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-06-18 23:25:27 -04:00
Zou Wei
d8b34a32a4 scsi: ufs: ufs-mediatek: Add missing of_node_put() in ufs_mtk_probe()
The function is missing a of_node_put() on node. Fix this by adding the
call before returning.

Link: https://lore.kernel.org/r/1623929522-4389-1-git-send-email-zou_wei@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-06-18 23:01:04 -04:00
Dan Carpenter
7cca85dff2 scsi: elx: libefc: Fix IRQ restore in efc_domain_dispatch_frame()
Calling a nested spin_lock_irqsave() will overwrite the original "flags" so
that they can not be enabled again at the end.

Link: https://lore.kernel.org/r/YMyjH16k4M1yEmmU@mwanda
Fixes: 3146240f19 ("scsi: elx: libefc: FC Domain state machine interfaces")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-06-18 23:01:04 -04:00
Colin Ian King
99cf922692 scsi: elx: libefc: Fix less than zero comparison of a unsigned int
The comparison of the u32 variable rc to less than zero always false
because it is unsigned. Fix this by making it an int.

Link: https://lore.kernel.org/r/20210616170401.15831-1-colin.king@canonical.com
Fixes: 202bfdffae ("scsi: elx: libefc: FC node ELS and state handling")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unsigned compared against 0")
2021-06-18 23:01:04 -04:00