Remove the remainder of assert() in places where the condition is
already handled.
Signed-off-by: Martiros Shakhzadyan <vrzh@vrzh.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove assert() in places where the condition is already handled.
Signed-off-by: Martiros Shakhzadyan <vrzh@vrzh.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Align line break to match with the open parenthesis.
Issue detected by checkpatch.pl.
Signed-off-by: Aline Santana Cordeiro <alinesantanacordeiro@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Balance braces around conditional statements.
Issue detected by checkpatch.pl.
It happens in if-else statements where one of the commands
uses braces around a block of code and the other command
does not since it has just a single line of code.
Signed-off-by: Aline Santana Cordeiro <alinesantanacordeiro@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Balance braces around conditional statements.
Issue detected by checkpatch.pl.
It happens in if-else statements where one of the commands
uses braces around a block of code and the other command
does not since it has just a single line of code.
Signed-off-by: Aline Santana Cordeiro <alinesantanacordeiro@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Balance braces around conditional statements.
Issue detected by checkpatch.pl.
It happens in if-else statements where one of the commands
uses braces around a block of code and the other command
does not since it has just a single line of code.
Signed-off-by: Aline Santana Cordeiro <alinesantanacordeiro@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Balance braces around conditional statements.
Issue detected by checkpatch.pl.
It happens in if-else statements where one of the commands
uses braces around a block of code and the other command
does not since it has just a single line of code.
Signed-off-by: Aline Santana Cordeiro <alinesantanacordeiro@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When first-level page tables are used for IOVA translation, we use user
privilege by setting U/S bit in the page table entry. This is to make it
consistent with the second level translation, where the U/S enforcement
is not available. Clear the SRE (Supervisor Request Enable) field in the
pasid table entry of RID2PASID so that requests requesting the supervisor
privilege are blocked and treated as DMA remapping faults.
Fixes: b802d070a5 ("iommu/vt-d: Use iova over first level")
Suggested-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210512064426.3440915-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20210519015027.108468-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When instantiating a tiled object on an L-shaped memory machine, we mark
the object as unshrinkable to prevent the shrinker from trying to swap
out the pages. We have to do this as we do not know the swizzling on the
individual pages, and so the data will be scrambled across swap out/in.
Not only do we need to move the object off the shrinker list, we need to
mark the object with shrink_pin so that the counter is consistent across
calls to madvise.
v2: in the madvise ioctl we need to check if the object is currently
shrinkable/purgeable, not if the object type supports shrinking
Fixes: 0175969e48 ("drm/i915/gem: Use shrinkable status for unknown swizzle quirks")
References: https://gitlab.freedesktop.org/drm/intel/-/issues/3293
References: https://gitlab.freedesktop.org/drm/intel/-/issues/3450
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: <stable@vger.kernel.org> # v5.12+
Link: https://patchwork.freedesktop.org/patch/msgid/20210517084640.18862-1-matthew.auld@intel.com
(cherry picked from commit 8777d17b68)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The __nvmf_check_ready() routine used to bounce all filesystem io if the
controller state isn't LIVE. However, a later patch changed the logic so
that it rejection ends up being based on the Q live check. The FC
transport has a slightly different sequence from rdma and tcp for
shutting down queues/marking them non-live. FC marks its queue non-live
after aborting all ios and waiting for their termination, leaving a
rather large window for filesystem io to continue to hit the transport.
Unfortunately this resulted in filesystem I/O or applications seeing I/O
errors.
Change the FC transport to mark the queues non-live at the first sign of
teardown for the association (when I/O is initially terminated).
Fixes: 73a5379937 ("nvme-fabrics: allow to queue requests for live queues")
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A possible race condition exists where the request to send data is
enqueued from nvme_tcp_handle_r2t()'s will not be observed by
nvme_tcp_send_all() if it happens to be running. The driver relies on
io_work to send the enqueued request when it is runs again, but the
concurrently running nvme_tcp_send_all() may not have released the
send_mutex at that time. If no future commands are enqueued to re-kick
the io_work, the request will timeout in the SEND_H2C state, resulting
in a timeout error like:
nvme nvme0: queue 1: timeout request 0x3 type 6
Ensure the io_work continues to run as long as the req_list is not empty.
Fixes: db5ad6b7f8 ("nvme-tcp: try to send request in queue_rq context")
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Commit db5ad6b7f8 ("nvme-tcp: try to send request in queue_rq
context") added a second context that may perform a network send.
This means that now RX and TX are not serialized in nvme_tcp_io_work
and can run concurrently.
While there is correct mutual exclusion in the TX path (where
the send_mutex protect the queue socket send activity) RX activity,
and more specifically request completion may run concurrently.
This means we must guarantee that any mutation of the request state
related to its lifetime, bytes sent must not be accessed when a completion
may have possibly arrived back (and processed).
The race may trigger when a request completion arrives, processed
_and_ reused as a fresh new request, exactly in the (relatively short)
window between the last data payload sent and before the request iov_iter
is advanced.
Consider the following race:
1. 16K write request is queued
2. The nvme command and the data is sent to the controller (in-capsule
or solicited by r2t)
3. After the last payload is sent but before the req.iter is advanced,
the controller sends back a completion.
4. The completion is processed, the request is completed, and reused
to transfer a new request (write or read)
5. The new request is queued, and the driver reset the request parameters
(nvme_tcp_setup_cmd_pdu).
6. Now context in (2) resumes execution and advances the req.iter
==> use-after-completion as this is already a new request.
Fix this by making sure the request is not advanced after the last
data payload send, knowing that a completion may have arrived already.
An alternative solution would have been to delay the request completion
or state change waiting for reference counting on the TX path, but besides
adding atomic operations to the hot-path, it may present challenges in
multi-stage R2T scenarios where a r2t handler needs to be deferred to
an async execution.
Reported-by: Narayan Ayalasomayajula <narayan.ayalasomayajula@wdc.com>
Tested-by: Anil Mishra <anil.mishra@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Cc: stable@vger.kernel.org # v5.8+
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When creating loop ctrl in nvme_loop_create_ctrl(), if nvme_init_ctrl()
fails, the loop ctrl should be freed before jumping to the "out" label.
Fixes: 3a85a5de29 ("nvme-loop: add a NVMe loopback host driver")
Signed-off-by: Wu Bo <wubo40@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When creating ctrl in nvmet_alloc_ctrl(), if the cntlid_min is larger
than cntlid_max of the subsystem, and jumps to the
"out_free_changed_ns_list" label, but the ctrl->sqs lack of be freed.
Fix this by jumping to the "out_free_sqs" label.
Fixes: 94a39d61f8 ("nvmet: make ctrl-id configurable")
Signed-off-by: Wu Bo <wubo40@huawei.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
It's not correct to call napi_schedule() in pure process
context. Because we use __raise_softirq_irqoff() we require
callers to be in a context which will eventually lead to
softirq handling (hardirq, bh disabled, etc.).
With code as is users will see:
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
Fixes: a8dd7ac12f ("net/mlx5e: Generalize RQ activation")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Termination tables are restricted to have the default miss action and
cannot be set to forward to another table in case of a miss.
If the fs prio of the termination table is not the last one in the
list, fs_core will attempt to attach it to another table.
Set the unmanaged ft flag when creating the termination table ft
and select the tc offload prio for it to prevent fs_core from selecting
the forwarding to next ft miss action and use the default one.
In addition, set the flow that forwards to the termination table to
ignore ft level restrictions since the ft level is not set by fs_core
for unamanged fts.
Fixes: 249ccc3c95 ("net/mlx5e: Add support for offloading traffic from uplink to uplink")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
During driver probe of device that has dynamic MSI-X feature enabled,
the following error is printed in some FW flavour (not released yet).
mlx5_core 0000:06:00.0: firmware version: 4.7.4387
mlx5_core 0000:06:00.0: 126.016 Gb/s available PCIe bandwidth (8.0 GT/s PCIe x16 link)
mlx5_core 0000:06:00.0: mlx5_cmd_check:777:(pid 70599): SET_HCA_CAP(0x109) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x0)
mlx5_core 0000:06:00.0: set_hca_cap:622:(pid 70599): handle_hca_cap failed
mlx5_core 0000:06:00.0: mlx5_function_setup:1045:(pid 70599): set_hca_cap failed
mlx5_core 0000:06:00.0: probe_one:1465:(pid 70599): mlx5_init_one failed with error code -22
mlx5_core: probe of 0000:06:00.0 failed with error -22
In order to make the setting capability of MSI-X future proof, let's
query the current capabilities first.
Fixes: 604774add5 ("net/mlx5: Dynamically assign MSI-X vectors count")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
net/mlx5: Expose MPFS configuration API
MPFS is the multi physical function switch that bridges traffic between
the physical port and any physical functions associated with it. The
driver is required to add or remove MAC entries to properly forward
incoming traffic to the correct physical function.
We export the API to control MPFS so that other drivers, such as
mlx5_vdpa are able to add MAC addresses of their network interfaces.
The MAC address of the vdpa interface must be configured into the MPFS L2
address. Failing to do so could cause, in some NIC configurations, failure
to forward packets to the vdpa network device instance.
Fix this by adding calls to update the MPFS table.
CC: <mst@redhat.com>
CC: <jasowang@redhat.com>
CC: <virtualization@lists.linux-foundation.org>
Fixes: 1a86b377aa ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Avoid division by zero in the error flow. In the driver TC number can be
either 1 or 8. When TC count is set to 1, driver zero netdev->num_tc.
Hence, need to convert it back from 0 to 1 in the error flow.
Fixes: fa3748775b ("net/mlx5e: Handle errors from netif_set_real_num_{tx,rx}_queues")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Rules with MLX5_ESW_DEST_CHAIN_WITH_SRC_PORT_CHANGE dest flag are
translated to destination FT in eswitch. Currently it is not possible to
mirror such rules because firmware doesn't support mixing FT and Vport
destinations in single rule when one of them adds encapsulation. Since the
only use case for MLX5_ESW_DEST_CHAIN_WITH_SRC_PORT_CHANGE destination is
support for tunnel endpoints on VF and trying to offload such rule with
mirror action causes either crash in fs_core or firmware error with
syndrome 0xff6a1d, reject all such rules in mlx5 TC layer.
Fixes: 10742efc20 ("net/mlx5e: VF tunnel TX traffic offloading")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When handling FIB_EVENT_ENTRY_REPLACE event for a new multipath route,
lag activation can be missed if a stale (struct lag_mp)->mfi pointer
exists, which was associated with an older multipath route that had been
removed.
Normally, when a route is removed, it triggers mlx5_lag_fib_event(),
which handles FIB_EVENT_ENTRY_DEL and clears mfi pointer. But, if
mlx5_lag_check_prereq() condition isn't met, for example when eswitch is
in legacy mode, the fib event is skipped and mfi pointer becomes stale.
Fix by resetting mfi pointer to NULL every time mlx5_lag_mp_init() is
called.
Fixes: 544fe7c2e6 ("net/mlx5e: Activate HW multipath and handle port affinity based on FIB events")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
mlx5e_attach_netdev can be called prior to registering the netdevice:
Example stack:
ipoib_new_child_link ->
ipoib_intf_init->
rdma_init_netdev->
mlx5_rdma_setup_rn->
mlx5e_attach_netdev->
mlx5e_num_channels_changed ->
mlx5e_set_default_xps_cpumasks ->
netif_set_xps_queue ->
__netif_set_xps_queue -> kmalloc
If any later stage fails at any point after mlx5e_num_channels_changed()
returns, XPS allocated maps will never be freed as they
are only freed during netdev unregistration, which will never happen for
yet to be registered netdevs.
Fixes: 3909a12e79 ("net/mlx5e: Fix configuration of XPS cpumasks and netdev queues in corner cases")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
It could be the lag dev is null so stop processing the event.
In bond_enslave() the active/backup slave being set before setting the
upper dev so first event is without an upper dev.
After setting the upper dev with bond_master_upper_dev_link() there is
a second event and in that event we have an upper dev.
Fixes: 7e51891a23 ("net/mlx5e: Use netdev events to set/del egress acl forward-to-vport rule")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The result of __dev_get_by_index() is not checked for NULL, which then
passed to mlx5e_attach_encap() and gets dereferenced.
Also, in case of a successful lookup, the net_device reference count is
not incremented, which may result in net_device pointer becoming invalid
at any time during mlx5e_attach_encap() execution.
Fix by using dev_get_by_index(), which does proper reference counting on
the net_device pointer. Also, handle nullptr return value when mirred
device is not found.
It's safe to call dev_put() on the mirred net_device pointer, right
after mlx5e_attach_encap() call, because it's not being saved/copied
down the call chain.
Fixes: 3c37745ec6 ("net/mlx5e: Properly deal with encap flows add/del under neigh update")
Addresses-Coverity: ("Dereference null return value")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When a SF is inactivated and when it is in a TEARDOWN_REQUEST
state, driver still returns its state as active. This is incorrect.
Fix it by treating TEARDOWN_REQEUST as inactive state. When a SF
is still attached to the driver, on user request to reactivate EINVAL
error is returned. Inform user about it with better code EBUSY and
informative error message.
Fixes: 6a32732174 ("net/mlx5: SF, Port function state change support")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Fix print to print correct error code and not using IS_ERR() which
will just result in always printing 1.
Also return real err instead of always -EOPNOTSUPP.
Fixes: 10caabdaad ("net/mlx5e: Use termination table for VLAN push actions")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
For remote mirroring, after the tunnel packets are received, they are
decapsulated and sent to representor, then re-encapsulated and sent
out over another tunnel. So reformat action is set only when the
destination is required to do encapsulation.
Fixes: 249ccc3c95 ("net/mlx5e: Add support for offloading traffic from uplink to uplink")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The result of dev_get_by_index_rcu() is not checked for NULL and then
gets dereferenced immediately.
Also, the RCU lock must be held by the caller of dev_get_by_index_rcu(),
which isn't satisfied by the call stack.
Fix by handling nullptr return value when iflink device is not found.
Add RCU locking around dev_get_by_index_rcu() to avoid possible adverse
effects while iterating over the net_device's hlist.
It is safe not to increment reference count of the net_device pointer in
case of a successful lookup, because it's already handled by VLAN code
during VLAN device registration (see register_vlan_dev and
netdev_upper_dev_link).
Fixes: 278748a95a ("net/mlx5e: Offload TC e-switch rules with egress VLAN device")
Addresses-Coverity: ("Dereference null return value")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
mlx5_core_dev holds pointer to static profile, hence when the
log_max_qp of the profile is override by some device, then it
effect all other mlx5 devices that share the same profile.
Fix it by having a profile instance for every mlx5 device.
Fixes: 883371c453 ("net/mlx5: Check FW limitations on log_max_qp before setting it")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The PMI8994 has 4 multi-purpose-pins, add a compatible for this hardware
block to the MPP driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210429003751.224232-1-bjorn.andersson@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We've a lot of places where we have pairs of form (pointer to end
of buffer, amount of space left in front of that). These sit in pairs of
variables located next to each other and usually passed by reference.
Turn those into instances of new type (struct prepend_buffer) and pass
reference to the pair instead of pairs of references to its fields.
Declared and initialized by DECLARE_BUFFER(name, buf, buflen).
extract_string(prepend_buffer) returns the buffer contents if
no overflow has happened, ERR_PTR(ENAMETOOLONG) otherwise.
All places where we used to have that boilerplate converted to use
of that helper.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Kernel test robot throws below warning ->
drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c:2705: warning: This comment
starts with '/**', but isn't a kernel-doc comment. Refer
Documentation/doc-guide/kernel-doc.rst
drivers/pinctrl/aspeed/pinctrl-aspeed-g6.c:2614: warning: This comment
starts with '/**', but isn't a kernel-doc comment. Refer
Documentation/doc-guide/kernel-doc.rst
drivers/pinctrl/aspeed/pinctrl-aspeed.c:111: warning: This comment
starts with '/**', but isn't a kernel-doc comment. Refer
Documentation/doc-guide/kernel-doc.rst
drivers/pinctrl/aspeed/pinmux-aspeed.c:24: warning: This comment starts
with '/**', but isn't a kernel-doc comment. Refer
Documentation/doc-guide/kernel-doc.rst
Fix minor documentation error.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/1619353584-8196-1-git-send-email-jrdr.linux@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It returns only 0 or -ENAMETOOLONG and both callers only check if
the result is negative. Might as well return true on success and
false on failure...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The only negative value ever returned by prepend_path() is -ENAMETOOLONG
and callers can recognize that situation (overflow) by looking at the
sign of buflen. Lift that into the callers; we already have the
same logics (buf if buflen is non-negative, ERR_PTR(-ENAMETOOLONG) otherwise)
in several places and that'll become a new primitive several commits down
the road.
Make prepend_path() return 0 instead of -ENAMETOOLONG. That makes for
saner calling conventions (0/1/2/3/-ENAMETOOLONG is obnoxious) and
callers actually get simpler, especially once the aforementioned
primitive gets added.
In prepend_path() itself we switch prepending the / (in case of
empty path) to use of prepend() - no need to open-code that, compiler
will do the right thing. It's exactly the same logics as in
__dentry_path().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Only simple_dname() checks it, and there we can simply do those
calls and check for overflow (by looking of negative buflen)
in the end.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The only negative value that might get returned by prepend_path() is
-ENAMETOOLONG, and that happens only on overflow. The same goes for
prepend_unreachable(). Overflow is detectable by observing negative
buflen, so we can simplify the control flow around the prepend_path()
call. Expand prepend_unreachable(), while we are at it - that's the
only caller.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
expand in the sole caller; transform the initial prepends similar to
what we'd done in dentry_path() (prepend_path() will fail the right
way if we call it with negative buflen, same as __dentry_path() does).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
All path-forming primitives boil down to sequence of prepend_name()
on dentries encountered along the way toward root. Each time we prepend
/ + dentry name to the buffer. Normally that does exactly what we want,
but there's a corner case when we don't call prepend_name() at all (in case
of __dentry_path() that happens if we are given root dentry). We obviously
want to end up with "/", rather than "", so this corner case needs to be
handled.
__dentry_path() used to manually put '/' in the end of buffer before
doing anything else, to be overwritten by the first call of prepend_name()
if one happens and to be left in place if we don't call prepend_name() at
all. That required manually checking that we had space in the buffer
(prepend_name() and prepend() take care of such checks themselves) and lead
to clumsy keeping track of return value.
A better approach is to check if the main loop has added anything
into the buffer and prepend "/" if it hasn't. A side benefit of using prepend()
is that it does the right thing if we'd already run out of buffer, making
the overflow-handling logics simpler.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Important: this change converts the binding as it is. It includes
dependency on undocumented CRU that must be refactored. CRU must get
documented and offset property has to be reworked.
Above can (and will be) be handled once every CRU MFD subdevice gets
documented properly (including the pinmux).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210421182041.22636-1-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>