This adds ABI documentation for the new configfs attributes that come
with the MIPI SyS-T protocol driver.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for CLOCKSYNC SyS-T packets, that establish correlation
between the transport clock (STP timestamps) and SyS-T timestamps. These
packets are sent periodically to allow the decoder to keep both time
sources in sync.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for MIPI SyS-T protocol as specified in an open
standard [1]. In addition to marking message boundaries, it also
supports tagging messages with the source UUID, to provide better
distinction between trace sources, including payload length and
timestamp in the message's metadata.
This driver adds attributes to STP policy nodes to control/configure
these metadata features.
[1] https://www.mipi.org/specifications/sys-t
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the default framing protocol is factored out into its own driver,
switch over to using the driver for writing data. To that end, make the
policy code require a valid protocol name (or absence thereof, which is
equivalent to "p_basic").
Also, to make transition easier, make stm class request "p_basic" module
at initialization time.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The STP framing pattern that the stm class implicitly applies to the
data payload is, in fact, a protocol. This patch moves the relevant code
out of the stm core into its own driver module.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a helper to write a sequence of bytes as STP data packets. This
is used by protocol drivers to output their metadata, as well as the
actual data payload.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the moment, the stm class applies a certain STP framing pattern to
the data as it is written to the underlying STM device. In order to
allow different framing patterns (aka protocols), this patch introduces
the concept of STP protocol drivers, defines data structures and APIs
for the protocol drivers to use.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current naming of stp-policy root type and group ops is confusing,
rename them for better readability.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, if no matching policy node can be found for a trace source,
we'll try to use "default" policy node, then, if that doesn't exist,
we'll pick the first node, in order of creation. If that also fails,
we'll allocate M/C range from the beginning of the device's M/C range.
This makes it difficult to know which node (if any) was used in any
particular case.
In order to make things more deterministic, the new order is as follows:
* if they supply ID string, use that and nothing else,
* if they are a task, use their task name (comm),
* use "default", if it exists,
* return failure, to let them know there is no suitable rule.
This should provide enough convenience with the "default" catch-all node,
while not leaving *everything* to chance. As a side effect, this relaxes
the requirement of using ioctl() for identification with the possibility of
using task names as policy nodes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not obvious how the code prevents adding more than 31 elements to
the list and thus invoking undefined behaviour in the 1 << new_lbid
expression, and in practice causing ->lbid values to repeat every 32
elements.
But the definition of struct gb_loopback is local to loopback.c, and the
lbid field is entirely unused outside of this function, so it seems we
can just drop it entirely.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix for a style warning using the help without the
deprecated help included between dashes.
Reported by checkpatch.
Signed-off-by: Ioannis Valasakis <code@wizofe.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix Sparse warnings:
drivers/staging/vboxvideo/vbox_mode.c:309:6: warning:
symbol 'vbox_primary_atomic_disable' was not declared. Should it be static?
drivers/staging/vboxvideo/vbox_mode.c:452:6: warning:
symbol 'vbox_cursor_atomic_disable' was not declared. Should it be static?
Signed-off-by: Craig Kewley <craigkewley@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to unlock before returning on this error path.
Fixes: 35f3288c45 ("staging: vboxvideo: Atomic phase 1: convert cursor to universal plane")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zero pad private area, otherwise we expose private kernel pointer to
userspace. This patch also zeroes the tail area after the ->matchsize
and ->targetsize that results from XT_ALIGN().
Fixes: 0ca743a559 ("netfilter: nf_tables: add compatibility layer for x_tables")
Reported-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
checkentry(tee_tg_check) should initialize priv->oif from dev if possible.
But only netdevice notifier handler can set that.
Hence priv->oif is always -1 until notifier handler is called.
Fixes: 9e2f6c5d78 ("netfilter: Rework xt_TEE netdevice notifier")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
TEE netdevice notifier handler checks only interface name. however
each netns can have same interface name. hence other netns's interface
could be selected.
test commands:
%ip netns add vm1
%iptables -I INPUT -p icmp -j TEE --gateway 192.168.1.1 --oif enp2s0
%ip link set enp2s0 netns vm1
Above rule is in the root netns. but that rule could get enp2s0
ifindex of vm1 by notifier handler.
After this patch, TEE rule is added to the per-netns list.
Fixes: 9e2f6c5d78 ("netfilter: Rework xt_TEE netdevice notifier")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The nft_osf extension, like xt_osf, is not supported from the output
path.
Fixes: b96af92d6e ("netfilter: nf_tables: implement Passive OS fingerprint module in nft_osf")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Allow to find closest matching for the right side of an interval (end
flag set on) so we allow lookups in inner ranges, eg. 10-20 in 5-25.
Fixes: ba0e4d9917 ("netfilter: nf_tables: get set elements via netlink")
Reported-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
drm_dp_cec_register_connector() is called when registering each DP
connector in DRM, while sounds a good idea register CEC adapters as
earlier as possible, it causes some driver initialization delay
trying to do DPCD transactions in disconnected connectors.
This change will cause no regressions as drm_dp_cec_set_edid() will
still be called in further detection of connected connectors with a
valid edid parameter.
This change reduced the module load of i915 by average 0.5sec in a
machine with just one DP port disconnected while reducing more than
3sec in a machine with 4 DP ports disconnected.
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181011004439.4482-1-jose.souza@intel.com
Refresh the document:
- Remove unnecessary liguistic complexity and improve the clarity of the text
- Improve the explanations all around
- Remove unnecessary and stale version info
- Fix whitespace noise
- Make pseudo-code match kernel style
- Fix minor syntax errors in pseudo-code
- Use consistent denotation
- Mark multi-CPU sequences more explicitly
- Unbreak line breaks
- Use quotes to refer to 'struct completion'
- Use 'IRQ context' and 'IRQs' consistently
- Improve grammar
- etc.
Cc: John Garry <john.garry@huawei.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicholas Mc Guire <hofrat@osadl.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: corbet@lwn.net
Cc: linux-doc@vger.kernel.org
Link: http://lkml.kernel.org/r/1539183392-239389-1-git-send-email-john.garry@huawei.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch fixes a couple of punctuation nits which can make the document
more correct and readable.
Also missing "()" are added to some function references for consistency.
Signed-off-by: John Garry <john.garry@huawei.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: corbet@lwn.net
Cc: linux-doc@vger.kernel.org
Link: http://lkml.kernel.org/r/1539183392-239389-1-git-send-email-john.garry@huawei.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When test_flow_dissector.sh runs it complains that it can't find script
with_addr.sh:
./test_flow_dissector.sh: line 81: ./with_addr.sh: No such file or
directory
Rework so that with_addr.sh gets installed, add it to
TEST_PROGS_EXTENDED variable.
Fixes: 50b3ed57de ("selftests/bpf: test bpf flow dissection")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When test_lwt_seg6local.sh was added commit c99a84eac0
("selftests/bpf: test for seg6local End.BPF action") config fragment
wasn't added, and without CONFIG_LWTUNNEL enabled we see this:
Error: CONFIG_LWTUNNEL is not enabled in this kernel.
selftests: test_lwt_seg6local [FAILED]
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Adding EXTRA_LDFLAGS allowing user to specify extra flags
for LD_FLAGS variable. Also adding LDFLAGS to build command
line.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Adding EXTRA_CFLAGS allowing user to specify extra flags
for CFLAGS variable.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The XSKMAP update and delete functions called synchronize_net(), which
can sleep. It is not allowed to sleep during an RCU read section.
Instead we need to make sure that the sock sk_destruct (xsk_destruct)
function is asynchronously called after an RCU grace period. Setting
the SOCK_RCU_FREE flag for XDP sockets takes care of this.
Fixes: fbfc504a24 ("bpf: introduce new bpf AF_XDP map type BPF_MAP_TYPE_XSKMAP")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This tag adds changes for the Texas Instruments clock driver. Included
changes are:
- clkctrl driver changes switching the layout from CM based to clockdomain
based. Needed for ongoing hwmod transition towards sysc driver. Changed
SoCs for this include am3,am4,am5,dra7.
- RTC+DDR sleep mode support code for clock save/restore. The deep sleep
states will wipe the clock register space on the SoC, requiring save/
restore support so that the state can be retained over the sleep state.
-----BEGIN PGP SIGNATURE-----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=RWln
-----END PGP SIGNATURE-----
Merge tag 'clk-ti-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux into clk-ti
Pull TI clock driver updates from Tero Kristo:
This tag adds changes for the Texas Instruments clock driver. Included
changes are:
- clkctrl driver changes switching the layout from CM based to clockdomain
based. Needed for ongoing hwmod transition towards sysc driver. Changed
SoCs for this include am3,am4,am5,dra7.
- RTC+DDR sleep mode support code for clock save/restore. The deep sleep
states will wipe the clock register space on the SoC, requiring save/
restore support so that the state can be retained over the sleep state.
* tag 'clk-ti-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
clk: ti: Add functions to save/restore clk context
clk: clk: Add clk_gate_restore_context function
clk: Add functions to save/restore clock context en-masse
clk: ti: dra7: add new clkctrl data
clk: ti: dra7xx: rename existing clkctrl data as compat data
clk: ti: am43xx: add new clkctrl data for am43xx
clk: ti: am43xx: rename existing clkctrl data as compat data
clk: ti: am33xx: add new clkctrl data for am33xx
clk: ti: am33xx: rename existing clkctrl data as compat data
clk: ti: clkctrl: replace dashes from clkdm name with underscore
clk: ti: clkctrl: support multiple clkctrl nodes under a cm node
dt-bindings: clock: dra7xx: add clkctrl indices for new data layout
dt-bindings: clock: am43xx: add clkctrl indices for new data layout
dt-bindings: clock: am33xx: add clkctrl indices for new data layout
clk: ti: fix OF child-node lookup
Salil Mehta says:
====================
Adds support of RSS to HNS3 Driver for Rev 2(=0x21) H/W
This patch-set mainly adds new additions related to RSS for the new
hardware Revision 0x21. It also adds support to use RSS hash value
provided by the hardware along with descriptor.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds RSS tuple support for VF in revision
0x21.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds RSS key, hash algorithm configuration support
for VF in revision 0x21.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ETH_RSS_HASH_XOR hash algorithm supports, which
is supported by hw revision 0x21.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for Gemalto's Cinterion ALASxx WWAN interfaces
by adding QMI_FIXED_INTF with Cinterion's VID and PID.
Signed-off-by: Giacinto Cifelli <gciofono@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tipc_sk_filter_rcv(), when we detect protocol messages with error we
call tipc_sk_conn_proto_rcv() and let it reset the connection and notify
the socket by calling sk->sk_state_change().
However, tipc_sk_filter_rcv() may have been called from the function
tipc_backlog_rcv(), in which case the socket lock is held and the socket
already awake. This means that the sk_state_change() call is ignored and
the error notification lost. Now the receive queue will remain empty and
the socket sleeps forever.
In this commit, we convert the protocol message into a connection abort
message and enqueue it into the socket's receive queue. By this addition
to the above state change we cover all conditions.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the patch referred to below we added link tolerance as an additional
criteria for declaring broadcast transmission "stale" and resetting the
affected links.
However, the 'tolerance' field of the broadcast link is never set, and
remains at zero. This renders the whole commit without the intended
improving effect, but luckily also with no negative effect.
In this commit we add the missing initialization.
Fixes: a4dc70d46c ("tipc: extend link reset criteria for stale packet retransmission")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function syscon_node_to_regmap() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: 51f6b410fc ("phy: add driver for Microsemi Ocelot SerDes muxing")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: dsa: bcm_sf2: Couple of fixes
Here are two fixes for the bcm_sf2 driver that were found during testing
unbind and analysing another issue during system suspend/resume.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to open code what the switch setup function does, in
fact, because we just issued a switch reset, we would make all the
register get their default values, including for instance, having unused
port be enabled again and wasting power and leading to an inappropriate
switch core clock being selected.
Fixes: 8cfa94984c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The order in which we release resources is unfortunately leading to bus
errors while dismantling the port. This is because we set
priv->wol_ports_mask to 0 to tell bcm_sf2_sw_suspend() that it is now
permissible to clock gate the switch. Later on, when dsa_slave_destroy()
comes in from dsa_unregister_switch() and calls
dsa_switch_ops::port_disable, we perform the same dismantling again, and
this time we hit registers that are clock gated.
Make sure that dsa_unregister_switch() is the first thing that happens,
which takes care of releasing all user visible resources, then proceed
with clock gating hardware. We still need to set priv->wol_ports_mask to
0 to make sure that an enabled port properly gets disabled in case it
was previously used as part of Wake-on-LAN.
Fixes: d9338023fb ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While noop_qdisc.gso_skb and noop_qdisc.skb_bad_txq are not used
in other places, it seems not correct to overwrite their fields
in dev_init_scheduler_queue().
noop_qdisc is essentially a shared and read-only object, even if
it is not marked as const because of some implementation detail.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without CONFIG_INET enabled compiles fail with:
net/mpls/af_mpls.o: In function `mpls_dump_routes':
af_mpls.c:(.text+0xed0): undefined reference to `ip_valid_fib_dump_req'
The preference is for MPLS to use the same handler as ipv4 and ipv6
to allow consistency when doing a dump for AF_UNSPEC which walks
all address families invoking the route dump handler. If INET is
disabled then fallback to an MPLS version which can be tighter on
the data checks.
Fixes: e8ba330ac0 ("rtnetlink: Update fib dumps for strict data checking")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca says:
====================
net: ipv4: fixes for PMTU when link MTU changes
The first patch adapts the changes that commit e9fa1495d7 ("ipv6:
Reflect MTU changes on PMTU of exceptions for MTU-less routes") did in
IPv6 to IPv4: lower PMTU when the first hop's MTU drops below it, and
raise PMTU when the first hop was limiting PMTU discovery and its MTU
is increased.
The second patch fixes bugs introduced in commit d52e5a7e7c ("ipv4:
lock mtu in fnhe when received PMTU < net.ipv4.route.min_pmtu") that
only appear once the first patch is applied.
Selftests for these cases were introduced in net-next commit
e44e428f59 ("selftests: pmtu: add basic IPv4 and IPv6 PMTU tests")
v2: add cover letter, and fix a few small things in patch 1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When an MTU update with PMTU smaller than net.ipv4.route.min_pmtu is
received, we must clamp its value. However, we can receive a PMTU
exception with PMTU < old_mtu < ip_rt_min_pmtu, which would lead to an
increase in PMTU.
To fix this, take the smallest of the old MTU and ip_rt_min_pmtu.
Before this patch, in case of an update, the exception's MTU would
always change. Now, an exception can have only its lock flag updated,
but not the MTU, so we need to add a check on locking to the following
"is this exception getting updated, or close to expiring?" test.
Fixes: d52e5a7e7c ("ipv4: lock mtu in fnhe when received PMTU < net.ipv4.route.min_pmtu")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 5aad1de5ea ("ipv4: use separate genid for next hop
exceptions"), exceptions get deprecated separately from cached
routes. In particular, administrative changes don't clear PMTU anymore.
As Stefano described in commit e9fa1495d7 ("ipv6: Reflect MTU changes
on PMTU of exceptions for MTU-less routes"), the PMTU discovered before
the local MTU change can become stale:
- if the local MTU is now lower than the PMTU, that PMTU is now
incorrect
- if the local MTU was the lowest value in the path, and is increased,
we might discover a higher PMTU
Similarly to what commit e9fa1495d7 did for IPv6, update PMTU in those
cases.
If the exception was locked, the discovered PMTU was smaller than the
minimal accepted PMTU. In that case, if the new local MTU is smaller
than the current PMTU, let PMTU discovery figure out if locking of the
exception is still needed.
To do this, we need to know the old link MTU in the NETDEV_CHANGEMTU
notifier. By the time the notifier is called, dev->mtu has been
changed. This patch adds the old MTU as additional information in the
notifier structure, and a new call_netdevice_notifiers_u32() function.
Fixes: 5aad1de5ea ("ipv4: use separate genid for next hop exceptions")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib6_info_alloc() function allocates percpu memory to hold per CPU
pointers to rt6_info, but this memory is never freed. Fix it.
Fixes: a64efe142f ("net/ipv6: introduce fib6_info struct and helpers")
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Hellwig says:
====================
fore200e DMA cleanups and fixes
The fore200e driver came up during some dma-related audits, so
here is the fallout. Compile tested (x86 & sparc) only.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was lacking any handling for failures from the DMA mapping
routines. With an iommu or swiotlb this can be fatal.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
