The driver does not check for Wake-on-LAN modes specified by an user,
but will conditionally set the device as wake-up enabled or not based on
that, which could be a very confusing user experience.
Fixes: e0e474a83c ("smsc95xx: add wol magic packet support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not check for Wake-on-LAN modes specified by an user,
but will conditionally set the device as wake-up enabled or not based on
that, which could be a very confusing user experience.
Fixes: 6c63650326 ("smsc75xx: add wol magic packet support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not check for Wake-on-LAN modes specified by an user,
but will conditionally set the device as wake-up enabled or not based on
that, which could be a very confusing user experience.
Fixes: 21ff2e8976 ("r8152: support WOL")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently silently accepts unsupported Wake-on-LAN modes
(other than WAKE_PHY or WAKE_MAGIC) without reporting that to the user,
which is confusing.
Fixes: 19a38d8e0a ("USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver supports a fair amount of Wake-on-LAN modes, but is not
checking that the user specified one that is supported.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Woojung Huh <Woojung.Huh@Microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently silently accepts unsupported Wake-on-LAN modes
(other than WAKE_PHY or WAKE_MAGIC) without reporting that to the user,
which is confusing.
Fixes: e2ca90c276 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently silently accepts unsupported Wake-on-LAN modes
(other than WAKE_PHY or WAKE_MAGIC) without reporting that to the user,
which is confusing.
Fixes: 2e55cc7210 ("[PATCH] USB: usbnet (3/9) module for ASIX Ethernet adapters")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2018-09-28
An update from ieee802154 for your *net* tree.
Some cleanup patches throughout the drivers from the Huawei tag team
Yue Haibing and Zhong Jiang.
Xue is replacing some magic numbers with defines in his mcr20a driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=MDV3
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-fixes-20180928' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fixes
Here are some miscellaneous fixes for AF_RXRPC:
(1) Remove a duplicate variable initialisation.
(2) Fix one of the checks made when we decide to set up a new incoming
service call in which a flag is being checked in the wrong field of
the packet header. This check is abstracted out into helper
functions.
(3) Fix RTT gathering. The code has been trying to make use of socket
timestamps, but wasn't actually enabling them. The code has also been
recording a transmit time for the outgoing packet for which we're
going to measure the RTT after sending the message - but we can get
the incoming packet before we get to that and record a negative RTT.
(4) Fix the emission of BUSY packets (we are emitting ABORTs instead).
(5) Improve error checking on incoming packets.
(6) Try to fix a bug in new service call handling whereby a BUG we should
never be able to reach somehow got triggered. Do this by moving much
of the checking as early as possible and not repeating it later
(depends on (5) above).
(7) Fix the sockopts set on a UDP6 socket to include the ones set on a
UDP4 socket so that we receive UDP4 errors and packet-too-large
notifications too.
(8) Fix the distribution of errors so that we do it at the point of
receiving an error in the UDP callback rather than deferring it
thereby cutting short any transmissions that would otherwise occur in
the window.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy says:
====================
tipc: make connection setup more robust
In this series we make a few improvements to the connection setup and
probing mechanism, culminating in the last commit where we make it
possible for a client socket to make multiple setup attempts in case
it encounters receive buffer overflow at the listener socket.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Default socket receive buffer size for a listener socket is 2Mb. For
each arriving empty SYN, the linux kernel allocates a 768 bytes buffer.
This means that a listener socket can serve maximum 2700 simultaneous
empty connection setup requests before it hits a receive buffer
overflow, and much fewer if the SYN is carrying any significant
amount of data.
When this happens the setup request is rejected, and the client
receives an ECONNREFUSED error.
This commit mitigates this problem by letting the client socket try to
retransmit the SYN message multiple times when it sees it rejected with
the code TIPC_ERR_OVERLOAD. Retransmission is done at random intervals
in the range of [100 ms, setup_timeout / 4], as many times as there is
room for within the setup timeout limit.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Messages intended for intitating a connection are currently
indistinguishable from regular datagram messages. The TIPC
protocol specification defines bit 17 in word 0 as a SYN bit
to allow sanity check of such messages in the listening socket,
but this has so far never been implemented.
We do that in this commit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We refactor the function tipc_sk_filter_connect(), both to make it
more readable and as a preparation for the next commit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We refactor this function as a preparation for the coming commits in
the same series.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_msg_reverse() is reversing the header of a message
while reusing the original buffer. We have seen at several occasions
that this may have unfortunate side effects when the buffer to be
reversed is a clone.
In one of the following commits we will again need to reverse cloned
buffers, so this is the right time to permanently eliminate this
problem. In this commit we let the said function always consume the
original buffer and replace it with a new one when applicable.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously TCP initial receive buffer is ~87KB by default and
the initial receive window is ~29KB (20 MSS). This patch changes
the two numbers to 128KB and ~64KB (rounding down to the multiples
of MSS) respectively. The patch also simplifies the calculations s.t.
the two numbers are directly controlled by sysctl tcp_rmem[1]:
1) Initial receiver buffer budget (sk_rcvbuf): while this should
be configured via sysctl tcp_rmem[1], previously tcp_fixup_rcvbuf()
always override and set a larger size when a new connection
establishes.
2) Initial receive window in SYN: previously it is set to 20
packets if MSS <= 1460. The number 20 was based on the initial
congestion window of 10: the receiver needs twice amount to
avoid being limited by the receive window upon out-of-order
delivery in the first window burst. But since this only
applies if the receiving MSS <= 1460, connection using large MTU
(e.g. to utilize receiver zero-copy) may be limited by the
receive window.
With this patch TCP memory configuration is more straight-forward and
more properly sized to modern high-speed networks by default. Several
popular stacks have been announcing 64KB rwin in SYNs as well.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c: In function ‘hclge_get_sset_count’:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:496:31: error: ‘HNAE3_REVISION_ID_21’ undeclared (first use in this function); did you mean ‘FADT2_REVISION_ID’?
if (hdev->pdev->revision >= HNAE3_REVISION_ID_21 ||
^~~~~~~~~~~~~~~~~~~~
FADT2_REVISION_ID
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c: In function ‘hns3_self_test’:
drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c:278:15: error: ‘HNS3_SELF_TEST_TYPE_NUM’ undeclared (first use in this function); did you mean ‘HNS3_SELF_TEST_TPYE_NUM’?
int st_param[HNS3_SELF_TEST_TYPE_NUM][2];
^~~~~~~~~~~~~~~~~~~~~~~
HNS3_SELF_TEST_TPYE_NUM
Signed-off-by: David S. Miller <davem@davemloft.net>
Bananapi released an updated revision of the H3/H5 based Bananapi M2+.
Version 1.2 enables voltage control for the CPU's regulator by using
a GPIO line to toggle a MOSFET that can change the effective resistance
value in the regulator's feedback network.
This patch adds a common .dtsi file for this new revision, which
includes the original common sunxi-bananapi-m2-plus.dtsi file, and
adds the GPIO-controlled regulator and a cpu-supply reference. H3
and H5 variant dts files are added as well.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This adds nodes for the Video Engine and the associated reserved memory
for the H3. Up to 96 MiB of memory are dedicated to the CMA pool.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Bananapi M2 Plus H5 is a variant of the original Bananapi M2 Plus,
with the H3 SoC replaced with an H5. Everything else is the same.
Add a stub device tree incorporating the shared bananapi-m2-plus dtsi
file.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Three more variants of the Bananapi M2 Plus have been introduced. One
with the H5 instead of the H3, another with the H2+ instead, and the
last with the H3 but with WiFi and eMMC removed.
All these variants use the same board. This patch splits out the
non-SoC-specific parts of the device tree, so that they can be shared
among all the variants. The original Bananapi M2 Plus has been renamed
to Bananapi M2 Plus H3.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The external RTL8211E RGMII Ethernet PHY is configured via external
resistors to use the address 0x1. The 0x0 address is a broadcast address
for this family of PHYs, and should not be used explicitly.
Fixes: 8c7ba536e7 ("ARM: sun8i: bananapi-m2-plus: Enable dwmac-sun8i")
Fixes: 4904337fe3 ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The size of the register should be the size of the whole memory block,
not just the registers, that are needed.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The H5 has a Mali-450 GPU with 4 Pixel Processor cores.
Interestingly, while the datasheet lists an interrupt line for the GPU's
PMU, the hardware block itself doesn't seem to have it. Reads from the
PMU address range all return zero, and writes are ignored.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Orangepi Zero Plus 2 is an open-source single-board computer, available in two
Allwinner SOC variants, H3 and H5. We add support for H3 variant here, as the
H5 is already supported by sun50i-h5-orangepi-zero-plus2.dts.
H3 Orangepi Zero Plus 2 has:
- Quad-core Cortex-A7
- 512MB DDR3
- microSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG + power supply
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The H5 SoC have a SID controller that looks like the one in A64, the
cells are in the same offset but doesn't contain the same data (thermal
sensor calibration for example).
Add a binding for it.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
There is currently a warning when building the Kryo cpufreq driver into
the kernel image:
WARNING: vmlinux.o(.text+0x8aa424): Section mismatch in reference from
the function qcom_cpufreq_kryo_probe() to the function
.init.text:qcom_cpufreq_kryo_get_msm_id()
The function qcom_cpufreq_kryo_probe() references
the function __init qcom_cpufreq_kryo_get_msm_id().
This is often because qcom_cpufreq_kryo_probe lacks a __init
annotation or the annotation of qcom_cpufreq_kryo_get_msm_id is wrong.
Remove the '__init' annotation from qcom_cpufreq_kryo_get_msm_id
so that there is no more mismatch warning.
Additionally, Nick noticed that the remove function was marked as
'__init' when it should really be marked as '__exit'.
Fixes: 46e2856b8e (cpufreq: Add Kryo CPU scaling driver)
Fixes: 5ad7346b4a (cpufreq: kryo: Add module remove and exit)
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.18+ <stable@vger.kernel.org> # 4.18+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Store fbhelper and afb struct directly in vbox_private and use
drm_fb_helper_fbdev_setup to replace vbox_fbdev_init, note we cannot use
drm_fb_helper_fbdev_teardown since we use a private framebuffer for the
fbdev.
And replace vbox_driver_lastclose with drm_fb_helper_lastclose.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vbox_mode_valid always returns MODE_OK, which is also the default if no
mode_valid callback is defined.
vbox_best_single_encoder chains to drm_encoder_find, the drm-core will
call drm_encoder_find itself if there is no best_encoder call back.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend our planes atomic_check callbacks to be more thorough by calling
the drm_atomic_helper_check_plane_state helper.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace vbox_crtc_commit and vbox_crtc_disable with
vbox_crtc_atomic_[en|dis]able which are the preferred callbacks for
these for atomic drivers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Atomic modesetting does not use the traditional dpms call backs, instead
we should check crtc_state->active.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restore page-flip support now that the atomic conversion is complete.
Since the mode parameter to vbox_crtc_set_base_and_mode() now never
is NULL call drm_atomic_crtc_needs_modeset() to check if we need to
check for input-mapping changes, to avoid doing unnecesarry work on
a flip. And hookup the drm_atomic_helper_page_flip helper to implement
the page_flip callback.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the state objects are wired up, we can:
1) Move to the final atomic handlers
2) Wire up atomic set_config helper
3) Switch to drm_mode_config_helper_suspend/resume for suspend/resume
4) Enable atomic modesetting ioctl
This is all done in one commit because doing this piecemeal leads to
an intermediate state which triggers WARN_ONs in the atomic code because
e.g. plane->fb is still being set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once we are fully atomic plane->fb will always be NULL and we also
should not access things like crtc->enabled and crt->[hw]mode.
Now that we've wired up the state object handlers, we always have a
plane_state and crtc_state so change the code referencing plane->fb and
crtc->* to use the data from the plane_state and crt_state instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wire up state object handlers for the crtc-s and the planes, call
drm_mode_config_reset() after creating all the crtc-s and encoders and
remove the legacy drm_helper_disable_unused_functions() call.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use drm_plane_helpers for the primary plane and replace our custom
mode_set callback with drm_helper_crtc_mode_set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for atomic conversion, let's use the transitional atomic
helpers drm_plane_helper_update/disable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When setting a mode we not only pass the mode to the hypervisor,
but also information on how to map / translate input coordinates
for the emulated USB tablet. This input-mapping may change when
the mode on *another* crtc changes.
This means that sometimes we must do a modeset on other crtc-s then
the one being changed to update the input-mapping. Including crtc-s
which may be disabled inside the guest (shown as a black window
on the host unless closed by the user).
With atomic modesetting the mode-info of disabled crtcs gets zeroed
yet we need it when updating the input-map to avoid resizing the
window as a side effect of a mode_set on another crtc.
This commit adds caching of the mode info into out private vbox_crtc
struct so that we always have the info at hand when we need it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm_mode_page_flip_ioctl() cannot deal with the in between phase of
the transitioning to atomic modeset support. Once we start using
drm_helper_crtc_mode_set(), we start setting plane->state on the primary
plane. But we are not fully atomic yet so then set both plane-state->fb
and plane->fb.
If both plane-state->fb and plane->fb are set drm_mode_page_flip_ioctl()
gets confused and stops calling drm_framebuffer_get() on the new fb while
still calling drm_framebuffer_put() on the old fb.
The current page_flip implementation expects drm_mode_page_flip_ioctl()
to take care of both and once we switch to drm_atomic_helper_page_flip()
that will expect neither to be done, taking care of both itself.
So for the transition we need to remove page_flip support and then after
the transition is complete and we set DRIVER_ATOMIC in our driver_features,
we can start using drm_atomic_helper_page_flip().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the encoder_helper_funcs are optional, and even setting the
drm_encoder_helper_funcs vtable itself is optional and may be left out
when not using any of the helper funcs, so lets drop all of this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This cleanups 2 things:
1) The first time we loop over the crtc-s, to compare framebuffers, fb1 may
get set to NULL by the fb1 = CRTC_FB(crtci); statement and then we call
to_vbox_framebuffer() on it. The result of this call is only used for
an address comparison, so we don't end up dereferencing the bad pointer,
but still it is better to not do this.
2) Since we already figure out the first crtc with a fb in the first loop
and store that in fb1, there is no need to loop over the crtc-s again just
to find the first crtc with a fb again.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The correct way to handle errors returned by regualtor_get() and friends is
to propagate the error since that means that an regulator was specified,
but something went wrong when requesting it.
For handling optional regulators, e.g. when the device has an internal
vref, regulator_get_optional() should be used to avoid getting the dummy
regulator that the regulator core otherwise provides.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Until now the "channel" number is identical to how the channel is
identified inside the (FIFO) registers. In our case we have eight
channels and the hardware also has eight inputs.
However, there are two special inputs:
- channel 6 can select between the SAR_ADC_CH6 pad and the chip's
internal temperature sensor
- channel 7 can select between SAR_ADC_CH7 and VSS, VDD / 4, VDD / 2,
VDD * 3 / 4 and VDD.
When programming the registers to read for example the temperature
sensor we have to select FIFO channel 6, set the correct bit which muxes
channel 6 to the temperature sensor and then start the ADC measurement
for channel 6 as usual.
When we add support for the temperature sensor the driver has to know
about that it has to use FIFO channel 6 to measure using the chip's
internal temperature sensor. However, in that case the iio_chan_spec
channel will not be 6 because this is already used for the SAR_ADC_CH6
pad input. Thus we use iio_chan_spec's address field to store the FIFO
channel number for each channel.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In the future we may support two different channel sets:
- one which includes the voltage pads and the temperature sensor output
(for Meson8, Meson8b and Meson8m2)
- one which only includes the voltage pads (GXBB, GXL, GXM and AXG)
Channel 7 has a special function on all of these platforms. However,
since we will have different channel array definitions we want our code
to always use whatever channels struct iio_dev uses.
No functional changes for now. This is the preparation for adding
temperature sensor support to this driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When channels are registered, the hardware channel number is not the
actual iio channel number.
This is because the driver is probed with a certain number of accessible
channels. Some pins are routed and some not, depending on the description of
the board in the DT.
Because of that, channels 0,1,2,3 can correspond to hardware channels
2,3,4,5 for example.
In the buffered triggered case, we need to do the translation accordingly.
Fixed the channel number to stop reading the wrong channel.
Fixes: 0e589d5fb ("ARM: AT91: IIO: Add AT91 ADC driver.")
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When doing simple conversions, the driver did not acknowledge the DRDY irq.
If this irq status is not acked, it will be left pending, and as soon as a
trigger is enabled, the irq handler will be called, it doesn't know why
this status has occurred because no channel is pending, and then it will go
int a irq loop and board will hang.
To avoid this situation, read the LCDR after a raw conversion is done.
Fixes: 0e589d5fb ("ARM: AT91: IIO: Add AT91 ADC driver.")
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 053ffe3c8c ("iio: adc: meson-saradc: squash and share the
common adc platform data") put all the data which is needed at runtime
from struct meson_sar_adc_data to a new struct meson_sar_adc_param so
we can re-use the platform specific configuration without having to
duplicate everything just to change the name.
The only place where struct meson_sar_adc_data is now needed is the
_probe function which has to pass the name to the iio_dev. All other
functions only need access to struct meson_sar_adc_param. This means we
can simplify struct meson_sar_adc_priv.
The goal of this patch is to make the code a bit easier to read since
this removes one level of nesting. No functional changes intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
