Prevent multiple registrations with transport layer for the same remote
port.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver uses shadow pointer instead of Mirror pointer for firmware dump
collection. Skip those entries for Mirror pointers for Request/Response
queue from firmware dump template reading.
Following messages are printed in log messages:
qla27xx_fwdt_entry_t268: unknown buffer 4
qla27xx_fwdt_entry_t268: unknown buffer 5
This patch fixes these error messages by adding skip_entry() to not read
them from template.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prevent user from sending commands through sysfs while firmware is not
running or reset is in progress.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qla2x00_reset_active only covers the window of turning the chip off. Add
check to cover turning chip on.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Login retry count was not properly decrementing which lead to endless
retry.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In case of N2N connect, sg_reset for bus/device/host was causing driver and
firmware state to go out of sync. This patch fixes this link instablity
when reconnect is attempted after link flap.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit d250bf4e776ff09d5("blk-mq: only iterate over inflight requests
in blk_mq_tagset_busy_iter") uses 'blk_mq_rq_state(rq) == MQ_RQ_IN_FLIGHT'
to replace 'blk_mq_request_started(req)', this way is wrong, and causes
lots of test system hang during booting.
Fix the issue by using blk_mq_request_started(req) inside bt_tags_iter().
Fixes: d250bf4e77 ("blk-mq: only iterate over inflight requests in blk_mq_tagset_busy_iter")
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Mark Brown <broonie@kernel.org>
Cc: Matt Hart <matthew.hart@linaro.org>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: John Garry <john.garry@huawei.com>
Cc: Hannes Reinecke <hare@suse.com>,
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>,
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: linux-scsi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Mark Brown <broonie@kernel.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This fix rounds the clock rate properly by using quotient and not
remainder in the calculation. This issue was found while testing HDMI
in the Juno platform.
Fixes: 6d6a1d82ea ("clk: add support for clocks provided by SCMI")
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The passed 'nr' from userspace represents the total depth, meantime
inside 'struct blk_mq_tags', 'nr_tags' stores the total tag depth,
and 'nr_reserved_tags' stores the reserved part.
There are two issues in blk_mq_tag_update_depth() now:
1) for growing tags, we should have used the passed 'nr', and keep the
number of reserved tags not changed.
2) the passed 'nr' should have been used for checking against
'tags->nr_tags', instead of number of the normal part.
This patch fixes the above two cases, and avoids kernel crash caused
by wrong resizing sbitmap queue.
Cc: "Ewan D. Milne" <emilne@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Omar Sandoval <osandov@fb.com>
Tested by: Marco Patalano <mpatalan@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Variables scriptb0 and dp_sgmin are being assigned but are never used
hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'scriptb0' set but not used [-Wunused-but-set-variable]
warning: variable 'dp_sgmin' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Updates csio_get_flash_params() to take care of ISSI, Macronix and
Winbond FLASH parts.
- Assume flash part size to be 4MB if it cannot be identified
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Right now, satellite tuner drivers specify frequencies in kHz,
while terrestrial/cable ones specify in Hz. That's confusing
for developers.
However, the main problem is that universal tuners capable
of handling both satellite and non-satelite delivery systems
are appearing. We end by needing to hack the drivers in
order to support such hybrid tuners.
So, convert everything to specify tuner frequencies in Hz.
Plese notice that a similar patch is also needed for frontends.
Tested-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The position calculation in iomap_bmap() shifts bno the wrong way,
so we don't progress properly and end up re-mapping block zero
over and over, yielding an unchanging physical block range as the
logical block advances:
# filefrag -Be file
ext: logical_offset: physical_offset: length: expected: flags:
0: 0.. 0: 21.. 21: 1: merged
1: 1.. 1: 21.. 21: 1: 22: merged
Discontinuity: Block 1 is at 21 (was 22)
2: 2.. 2: 21.. 21: 1: 22: merged
Discontinuity: Block 2 is at 21 (was 22)
3: 3.. 3: 21.. 21: 1: 22: merged
This breaks the FIBMAP interface for anyone using it (XFS), which
in turn breaks LILO, zipl, etc.
Bug-actually-spotted-by: Darrick J. Wong <darrick.wong@oracle.com>
Fixes: 89eb1906a9 ("iomap: add an iomap-based bmap implementation")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
A long time ago the unfortunate decision was taken to add a self-deletion
attribute to the sysfs SCSI device directory. That decision was unfortunate
because self-deletion is really tricky. We can't drop that attribute
because widely used user space software depends on it, namely the
rescan-scsi-bus.sh script. Hence this patch that avoids that writing into
that attribute triggers a deadlock. See also commit 7973cbd9fbd9 ("[PATCH]
add sysfs attributes to scan and delete scsi_devices").
This patch avoids that self-removal triggers the following deadlock:
======================================================
WARNING: possible circular locking dependency detected
4.18.0-rc2-dbg+ #5 Not tainted
------------------------------------------------------
modprobe/6539 is trying to acquire lock:
000000008323c4cd (kn->count#202){++++}, at: kernfs_remove_by_name_ns+0x45/0x90
but task is already holding lock:
00000000a6ec2c69 (&shost->scan_mutex){+.+.}, at: scsi_remove_host+0x21/0x150 [scsi_mod]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&shost->scan_mutex){+.+.}:
__mutex_lock+0xfe/0xc70
mutex_lock_nested+0x1b/0x20
scsi_remove_device+0x26/0x40 [scsi_mod]
sdev_store_delete+0x27/0x30 [scsi_mod]
dev_attr_store+0x3e/0x50
sysfs_kf_write+0x87/0xa0
kernfs_fop_write+0x190/0x230
__vfs_write+0xd2/0x3b0
vfs_write+0x101/0x270
ksys_write+0xab/0x120
__x64_sys_write+0x43/0x50
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
-> #0 (kn->count#202){++++}:
lock_acquire+0xd2/0x260
__kernfs_remove+0x424/0x4a0
kernfs_remove_by_name_ns+0x45/0x90
remove_files.isra.1+0x3a/0x90
sysfs_remove_group+0x5c/0xc0
sysfs_remove_groups+0x39/0x60
device_remove_attrs+0x82/0xb0
device_del+0x251/0x580
__scsi_remove_device+0x19f/0x1d0 [scsi_mod]
scsi_forget_host+0x37/0xb0 [scsi_mod]
scsi_remove_host+0x9b/0x150 [scsi_mod]
sdebug_driver_remove+0x4b/0x150 [scsi_debug]
device_release_driver_internal+0x241/0x360
device_release_driver+0x12/0x20
bus_remove_device+0x1bc/0x290
device_del+0x259/0x580
device_unregister+0x1a/0x70
sdebug_remove_adapter+0x8b/0xf0 [scsi_debug]
scsi_debug_exit+0x76/0xe8 [scsi_debug]
__x64_sys_delete_module+0x1c1/0x280
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&shost->scan_mutex);
lock(kn->count#202);
lock(&shost->scan_mutex);
lock(kn->count#202);
*** DEADLOCK ***
2 locks held by modprobe/6539:
#0: 00000000efaf9298 (&dev->mutex){....}, at: device_release_driver_internal+0x68/0x360
#1: 00000000a6ec2c69 (&shost->scan_mutex){+.+.}, at: scsi_remove_host+0x21/0x150 [scsi_mod]
stack backtrace:
CPU: 10 PID: 6539 Comm: modprobe Not tainted 4.18.0-rc2-dbg+ #5
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.0.0-prebuilt.qemu-project.org 04/01/2014
Call Trace:
dump_stack+0xa4/0xf5
print_circular_bug.isra.34+0x213/0x221
__lock_acquire+0x1a7e/0x1b50
lock_acquire+0xd2/0x260
__kernfs_remove+0x424/0x4a0
kernfs_remove_by_name_ns+0x45/0x90
remove_files.isra.1+0x3a/0x90
sysfs_remove_group+0x5c/0xc0
sysfs_remove_groups+0x39/0x60
device_remove_attrs+0x82/0xb0
device_del+0x251/0x580
__scsi_remove_device+0x19f/0x1d0 [scsi_mod]
scsi_forget_host+0x37/0xb0 [scsi_mod]
scsi_remove_host+0x9b/0x150 [scsi_mod]
sdebug_driver_remove+0x4b/0x150 [scsi_debug]
device_release_driver_internal+0x241/0x360
device_release_driver+0x12/0x20
bus_remove_device+0x1bc/0x290
device_del+0x259/0x580
device_unregister+0x1a/0x70
sdebug_remove_adapter+0x8b/0xf0 [scsi_debug]
scsi_debug_exit+0x76/0xe8 [scsi_debug]
__x64_sys_delete_module+0x1c1/0x280
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
See also https://www.mail-archive.com/linux-scsi@vger.kernel.org/msg54525.html.
Fixes: ac0ece9174 ("scsi: use device_remove_file_self() instead of device_schedule_callback()")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce these two functions and export them such that the next patch
can add calls to these functions from the SCSI core.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 12.0.0.6
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enablement of the PBDE optimization brought out some incompatible behaviors
under error scenarios.
Best to disable and remove the PBDE optimization.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After memory allocation for the LCB response frame, the memory wasn't zero
initialized, and not all fields are set. Thus garbage shows up in the
payload.
Fix by zeroing the memory at allocation. Also properly set the Capability
field based on duration support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Performance is affected when target queue depth is tracked. An atomic
counter is incremented on the submission path which competes with it being
decremented on the completion path. In addition, multiple CPUs can
simultaniously be manipulating this counter for the same ndlp.
Reduce the overhead by only performing the target increment/decrement when
the target queue depth is less than the overall adapter depth, thus is
actually meaningful.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During remote port loss fault testing, the driver crashed with the
following trace:
general protection fault: 0000 [#1] SMP
RIP: ... lpfc_nvme_register_port+0x250/0x480 [lpfc]
Call Trace:
lpfc_nlp_state_cleanup+0x1b3/0x7a0 [lpfc]
lpfc_nlp_set_state+0xa6/0x1d0 [lpfc]
lpfc_cmpl_prli_prli_issue+0x213/0x440
lpfc_disc_state_machine+0x7e/0x1e0 [lpfc]
lpfc_cmpl_els_prli+0x18a/0x200 [lpfc]
lpfc_sli_sp_handle_rspiocb+0x3b5/0x6f0 [lpfc]
lpfc_sli_handle_slow_ring_event_s4+0x161/0x240 [lpfc]
lpfc_work_done+0x948/0x14c0 [lpfc]
lpfc_do_work+0x16f/0x180 [lpfc]
kthread+0xc9/0xe0
ret_from_fork+0x55/0x80
After registering a new remoteport, the driver is pulling an ndlp pointer
from the lpfc rport associated with the private area of a newly registered
remoteport. The private area is uninitialized, so it's garbage.
Correct by pulling the the lpfc rport pointer from the entering ndlp point,
then ndlp value from at rport. Note the entering ndlp may be replacing by
the rport->ndlp due to an address change swap.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enabling list_debug showed the drivers txcmplq was suffering list
corruption. The systems will eventually crash because the iocb free list
gets crossed linked with the prings txcmplq. Most systems will run for a
while after the corruption, but will eventually crash when a scsi eh reset
occurs and the txcmplq is attempted to be flushed. The flush gets stuck in
an endless loop.
The problem is the abort handler does not hold the sli4 ring lock while
validating the IO so the IO could complete while the driver is still
preping the abort. The erroneously generated abort, when it completes, has
pointers to the original IO that has already completed, and the IO
manipulation (for the second time) corrupts the list.
Correct by taking the ring lock early in the abort handler so the erroneous
abort won't be sent if the io has/is completing.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
CNA ports were showing speed as "unknown" even if the link is up.
Add speed decoding for FCOE-based adapters.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For ABORT_XRI_CN command, firmware identifies XRI to abort by IOTAG and RPI
combination. For ELS aborts, driver specifies IOTAG correctly but RPI is
not specified.
Fix by setting RPI in WQE.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the offset is larger or equal to both real file size and
max file size, then return -EFBIG.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
If the range is larger than both real file size and limit of
max file size, then return -EFBIG.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
In order to not bother to VFS and other specific filesystems,
we decided to do offset validation inside ceph kernel client,
so just simply set sb->s_maxbytes to MAX_LFS_FILESIZE so that
it can successfully pass VFS check. We add new field max_file_size
in ceph_fs_client to store real file size limit and doing proper
check based on it.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Avoid scribbling over memory if the received reply/challenge is larger
than the buffer supplied with the authorizer.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Derive the signature from the entire buffer (both AES cipher blocks)
instead of using just the first half of the first block, leaving out
data_crc entirely.
This addresses CVE-2018-1129.
Link: http://tracker.ceph.com/issues/24837
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
When a client authenticates with a service, an authorizer is sent with
a nonce to the service (ceph_x_authorize_[ab]) and the service responds
with a mutation of that nonce (ceph_x_authorize_reply). This lets the
client verify the service is who it says it is but it doesn't protect
against a replay: someone can trivially capture the exchange and reuse
the same authorizer to authenticate themselves.
Allow the service to reject an initial authorizer with a random
challenge (ceph_x_authorize_challenge). The client then has to respond
with an updated authorizer proving they are able to decrypt the
service's challenge and that the new authorizer was produced for this
specific connection instance.
The accepting side requires this challenge and response unconditionally
if the client side advertises they have CEPHX_V2 feature bit.
This addresses CVE-2018-1128.
Link: http://tracker.ceph.com/issues/24836
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Will be used for encrypting both the initial and updated authorizers.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Will be used for decrypting the server challenge which is only preceded
by ceph_x_encrypt_header.
Drop struct_v check to allow for extending ceph_x_encrypt_header in the
future.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Will be used for sending ceph_msg_connect with an updated authorizer,
after the server challenges the initial authorizer.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
We already copy authorizer_reply_buf and authorizer_reply_buf_len into
ceph_connection. Factoring out __prepare_write_connect() requires two
more: authorizer_buf and authorizer_buf_len. Store the pointer to the
handshake in con->auth rather than piling on.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Remove blank lines at end of file and trailing whitespace.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Use new return type vm_fault_t for page_mkwrite
and fault handler.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The ceph_mds_request stamp still uses the deprecated timespec structure,
this converts it over as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The request mtime field is used all over ceph, and is currently
represented as a 'timespec' structure in Linux. This changes it to
timespec64 to allow times beyond 2038, modifying all users at the
same time.
[ Remove now redundant ts variable in writepage_nounlock(). ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
When receiving a LOGO request we forget to clear the FC_RP_STARTED flag
before starting the rport delete routine.
As the started flag was not cleared, we're not deleting the rport but
waiting for a restart and thus are keeping the reference count of the rdata
object at 1.
This leads to the following kmemleak report:
unreferenced object 0xffff88006542aa00 (size 512):
comm "kworker/0:2", pid 24, jiffies 4294899222 (age 226.880s)
hex dump (first 32 bytes):
68 96 fe 65 00 88 ff ff 00 00 00 00 00 00 00 00 h..e............
01 00 00 00 08 00 00 00 02 c5 45 24 ac b8 00 10 ..........E$....
backtrace:
[<(____ptrval____)>] fcoe_ctlr_vn_add.isra.5+0x7f/0x770 [libfcoe]
[<(____ptrval____)>] fcoe_ctlr_vn_recv+0x12af/0x27f0 [libfcoe]
[<(____ptrval____)>] fcoe_ctlr_recv_work+0xd01/0x32f0 [libfcoe]
[<(____ptrval____)>] process_one_work+0x7ff/0x1420
[<(____ptrval____)>] worker_thread+0x87/0xef0
[<(____ptrval____)>] kthread+0x2db/0x390
[<(____ptrval____)>] ret_from_fork+0x35/0x40
[<(____ptrval____)>] 0xffffffffffffffff
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: ard <ard@kwaak.net>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
KASAN reports a use-after-free in fcoe_ctlr_els_send() when we're sending a
LOGO and have FIP debugging enabled. This is because we're first freeing
the skb and then printing the frame's DID. But the DID is a member of the
FC frame header which in turn is the skb's payload.
Exchange the debug print and kfree_skb() calls so we're not touching the
freed data.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This converts drivers that were only calling transport_deregister_session
to use target_remove_session. The calling of
transport_deregister_session_configfs via target_remove_session for these
types of drivers is ok, because they were not exporting info from fields
like sess_acl_list, sess->se_tpg and sess->fabric_sess_ptr from configfs
accessible functions, so they will see no difference.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This converts tcm_fc to use target_remove_session
tcm_fc was calling transport_deregister_session_configfs then calling
transport_deregister_session when commands have completed. It should be ok
for it to call transport_deregister_session_configfs later via
target_remove_session because transport_deregister_session_configfs only
prevents access from configfs via tpg removal and its call to the
close_session callback for that driver, and this is already protected by
the ft_lport_lock and its port lookup handling.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This converts the drivers that called transport_deregister_session_configfs
and then immediately called transport_deregister_session to use
target_remove_session.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Chris Boot <bootc@bootc.net>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: <qla2xxx-upstream@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This adds a function to remove a session which should be used by drivers
that use target_setup_session. The next patches will convert the target
drivers to use this new function.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Chris Boot <bootc@bootc.net>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename target_alloc_session to target_setup_session to avoid confusion with
the other transport session allocation function that only allocates the
session and because the target_alloc_session does so much more. It
allocates the session, sets up the nacl and registers the session.
The next patch will then add a remove function to match the setup in this
one, so it should make sense for all drivers, except iscsi, to just call
those 2 functions to setup and remove a session.
iscsi will continue to be the odd driver.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Chris Boot <bootc@bootc.net>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
