Driver does both wmb() and writel(). The latter already has a barrier
on some architectures like arm64. This ends up with CPU observing two
barriers back to back before executing the register write.
Drivers should generally assume that the barrier implied by writel() is
sufficient for ordering DMA. Remove the extraneous wmb() before it.
[mkp: Squashed Arnd's and Sinan's patches]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Generally target core and TCMUser seem to work fine for tape devices and
media changers. But there is at least one situation where TCMUser is not
able to support sequential access device emulation correctly.
The situation is when an initiator sends a SCSI READ CDB with a length that
is greater than the length of the tape block to read. We can distinguish
two subcases:
A) The initiator sent the READ CDB with the SILI bit being set.
In this case the sequential access device has to transfer the data from
the tape block (only the length of the tape block) and transmit a good
status. The current interface between TCMUser and the userspace does
not support reduction of the read data size by the userspace program.
The patch below fixes this subcase by allowing the userspace program to
specify a reduced data size in read direction.
B) The initiator sent the READ CDB with the SILI bit not being set.
In this case the sequential access device has to transfer the data from
the tape block as in A), but additionally has to transmit CHECK
CONDITION with the ILI bit set and NO SENSE in the sensebytes. The
information field in the sensebytes must contain the residual count.
With the below patch a user space program can specify the real read data
length and appropriate sensebytes. TCMUser then uses the se_cmd flag
SCF_TREAT_READ_AS_NORMAL, to force target core to transmit the real data
size and the sensebytes. Note: the flag SCF_TREAT_READ_AS_NORMAL is
introduced by Lee Duncan's patch "[PATCH v4] target: transport should
handle st FM/EOM/ILI reads" from Tue, 15 May 2018 18:25:24 -0700.
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Acked-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ctxdmas for cursors from all heads are setup in the core channel, and due
to us tracking allocated handles per-window, we were failing with -EEXIST
on multiple-head setups trying to allocate duplicate handles.
The cursor code is hardcoded to use the core channel vram ctxdma already,
so just skip ctxdma allocation for cursor fbs to fix the issue.
Fixes: 5bca1621c0 ("drm/nouveau/kms/nv50-: move fb ctxdma tracking into windows")
Reported-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Add mem mode suspend for i.MX6SLL, when linux
kernel suspend, SoC will enter STOP mode,
ARM core will be power gated and MMDC IO
will be set to low power mode.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add standby mode suspend for i.MX6SLL, when
linux kernel suspend, SoC will enter STOP mode
with ARM core power on.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch enables hotplug interrupts for DP over TBT output on TC
ports. The TBT interrupts are enabled and handled irrespective of the
actual output type which could be DP Alternate, DP over TBT, native DP
or native HDMI.
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180616000530.5357-3-paulo.r.zanoni@intel.com
The hotplug interrupts for the ports can be routed to either North
Display or South Display depending on the output mode. DP Alternate or
DP over TBT outputs will have hotplug interrupts routed to the North
Display while interrupts for legacy modes will be routed to the South
Display in PCH. This patch adds hotplug interrupt handling support for
DP Alternate mode.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
[Paulo: coding style changes]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180616000530.5357-2-paulo.r.zanoni@intel.com
The Graphics System Event(GSE) interrupt bit has a new location in the
GU_MISC_INTERRUPT_{IIR, ISR, IMR, IER} registers. Since GSE was the only
DE_MISC interrupt that was enabled, with this change we don't enable/handle
any of DE_MISC interrupts for gen11. Credits to Paulo for pointing out
the register change.
v2: from DK
raw_reg_[read/write], branch prediction hint and drop platform check (Mika)
v3: From DK
Early re-enable of master interrupt (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
[Paulo: bikesheds and rebases]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180616000530.5357-1-paulo.r.zanoni@intel.com
IPQ8074 has an integrated Hexagon dsp core q6v5 and a wireless lan
(Lithium) IP. An mdt type single image format is used for the
firmware. So the mdt_load function can be directly used to load
the firmware. Also add the relevant resets required for this core.
Acked-by: Rob Herring <robh@kernel.org> (bindings)
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
[bjorn: Rewrote as a separate driver, intead of extending q6v5_pil.c]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Migrate the MSS remoteproc driver to use the newly extracted helper
functions.
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Migrate the Hexagon V5 PAS (ADSP) driver to using the newly extracted
helper functions. The use of the handover callback does introduce latent
disabling of proxy resources. But apart from this there should be no
change in functionality.
Reviewed-by: Rohit kumar <rohitkr@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Shared between all Hexagon V5 based remoteprocs is the handling of the 5
interrupts and the SMP2P stop request, so break this out into a separate
function in order to allow these drivers to be cleaned up.
Reviewed-by: Rohit kumar <rohitkr@codeaurora.org>
Tested-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
qcom_mdt_load function loads the mdt type firmware and
initialises the secure memory as well. Make the initialisation only
when requested by the caller, so that the function can be used
by self-authenticating remoteproc as well.
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
-----BEGIN PGP SIGNATURE-----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=fEwn
-----END PGP SIGNATURE-----
Merge tag 'jfs-4.18' of git://github.com/kleikamp/linux-shaggy
Pull jfs fix from Dave Kleikamp:
"This fixes a too-small allocation in the xattr code"
* tag 'jfs-4.18' of git://github.com/kleikamp/linux-shaggy:
jfs: Fix inconsistency between memory allocation and ea_buf->max_size
Pull s390 updates from Martin Schwidefsky:
"common I/O layer
- Fix bit-fields crossing storage-unit boundaries in css_general_char
dasd driver
- Avoid a sparse warning in regard to the queue lock
- Allocate the struct dasd_ccw_req as per request data. Only for
internal I/O is the structure allocated separately
- Remove the unused function dasd_kmalloc_set_cda
- Save a few bytes in struct dasd_ccw_req by reordering fields
- Convert remaining users of dasd_kmalloc_request to
dasd_smalloc_request and remove the now unused function
vfio/ccw
- Refactor and improve pfn_array_alloc_pin/pfn_array_pin
- Add a new tracepoint for failed vfio/ccw requests
- Add a CCW translation improvement to accept more requests as valid
- Bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/dasd: only use preallocated requests
s390/dasd: reshuffle struct dasd_ccw_req
s390/dasd: remove dasd_kmalloc_set_cda
s390/dasd: move dasd_ccw_req to per request data
s390/dasd: simplify locking in process_final_queue
s390/cio: sanitize css_general_characteristics definition
vfio: ccw: add tracepoints for interesting error paths
vfio: ccw: set ccw->cda to NULL defensively
vfio: ccw: refactor and improve pfn_array_alloc_pin()
vfio: ccw: shorten kernel doc description for pfn_array_pin()
vfio: ccw: push down unsupported IDA check
vfio: ccw: fix error return in vfio_ccw_sch_event
s390/archrandom: Rework arch random implementation.
s390/net: add pnetid support
The patch fixed a W=1 warning but broke the ia64 build:
CC mm/memblock.o
mm/memblock.c:1340: error: redefinition of `memblock_virt_alloc_try_nid_raw'
./include/linux/bootmem.h:335: error: previous definition of `memblock_virt_alloc_try_nid_raw' was here
Because inlcude/linux/bootmem.h says
#if defined(CONFIG_HAVE_MEMBLOCK) && defined(CONFIG_NO_BOOTMEM)
whereas mm/Makefile says
obj-$(CONFIG_HAVE_MEMBLOCK) += memblock.o
So revert 26f09e9b3a ("mm/memblock: add missing include
<linux/bootmem.h>") while a full fix can be worked on.
Fixes: 26f09e9b3a ("mm/memblock: add missing include <linux/bootmem.h>")
Reported-by: Tony Luck <tony.luck@gmail.com>
Cc: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow the code which provides extensions to support direct assignment
of Intel IGD (GVT-d) to be compiled out of the kernel if desired. The
config option for this was previously automatically enabled on X86,
therefore the default remains Y. This simply provides the option to
disable it even for X86.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Since I'm touching the file I might as well fix this class of errors
since they are just a few. Also drive-by fix the styling of the
VLV_TURBO_SOC_OVERRIDE definitions instead of just the spaces before
the tabs.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612235654.7914-3-paulo.r.zanoni@intel.com
Because OCD.
Now seriously, commit 1aa920ea0e ("drm/i915: add register macro
definition style guide") has finally established a coding standard to
be followed by the rest of the file, and I've been trying to request
everybody to adhere to that since then. The problem is that when
someone adds a new line to a register that has the wrong style, these
people generally propagate the wrong style and I have to keep asking
them to drive-by fix the whole register, which is not something I like
to do and also creates extra work for them. Or I can ignore the
propagation of the wrong coding style and feel anxious about it. On
top of that, we now have our CI happily reminding us about these
problems, which makes everything worse.
So IMHO the best way to proceed is to fix the spacing issues in the
file once and for all. Contributors will stop propagating the bad
style when adding new bits to registers that already have bad style,
we will stop asking them to redo their patches and the CI emails will
become more relevant by having less semi-false errors.
Yes, there will be some pain involved for backporters, but at least
spacing issues like that are easy to spot and fix in the patch files.
This patch was generated by:
../../../../scripts/checkpatch.pl -f --strict --types SPACING \
--fix-inplace i915_reg.h
I manually checked the output and everything seems sane.
v2: Single conflict around the addition of DP_TP_CTL_LINK_TRAIN_PAT4.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618180943.894-1-paulo.r.zanoni@intel.com
memcpy() of mapped addresses is done twice in c4iw_create_listen(),
removing the duplicate memcpy().
Fixes: 170003c894 ("iw_cxgb4: remove port mapper related code")
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The erratum and workaround are described by BCM5300X-ES300-RDS.pdf as
below.
R10: PCIe Transactions Periodically Fail
Description: The BCM5300X PCIe does not maintain transaction ordering.
This may cause PCIe transaction failure.
Fix Comment: Add a dummy PCIe configuration read after a PCIe
configuration write to ensure PCIe configuration access
ordering. Set ES bit of CP0 configu7 register to enable
sync function so that the sync instruction is functional.
Resolution: hndpci.c: extpci_write_config()
hndmips.c: si_mips_init()
mipsinc.h CONF7_ES
This is fixed by the CFE MIPS bcmsi chipset driver also for BCM47XX.
Also the dummy PCIe configuration read is already implemented in the
Linux BCMA driver.
Enable ExternalSync in Config7 when CONFIG_BCMA_DRIVER_PCI_HOSTMODE=y
too so that the sync instruction is externalised.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/19461/
Signed-off-by: James Hogan <jhogan@kernel.org>
I used bad names in my clumsiness when rewriting many board
files to use GPIO descriptors instead of platform data. A few
had the platform_device ID set to -1 which would indeed give
the device name "i2c-gpio".
But several had it set to >=0 which gives the names
"i2c-gpio.0", "i2c-gpio.1" ...
Fix the one affected board in the MIPS tree. Sorry.
Fixes: b2e6355559 ("i2c: gpio: Convert to use descriptors")
Reported-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.15+
Patchwork: https://patchwork.linux-mips.org/patch/19387/
Signed-off-by: James Hogan <jhogan@kernel.org>
These files weren't covered by the MAINTAINERS file,
add them.
Reported-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for HE in mac80211 conforming with P802.11ax_D1.4.
Johannes: Fix another bug with the buf_size comparison in agg-rx.c.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bump the IEEE80211_MAX_AMPDU_BUF size to 0x100 for HE support
and - for now - use IEEE80211_MAX_AMPDU_BUF_HT everywhere.
This is derived from my internal patch, parts of which Luca
had sent upstream.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The SELinux code, security/selinux/, already has a MAINTAINERS entry
so exclude it from the security subsystem entry in an effort to better
reflect current practices.
Signed-off-by: Paul Moore <paul@paul-moore.com>
Expand the Maud/Naud table according to DP 1.4 spec to include entries for
810 MHz clock. This is required for audio to work with HBR3.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180607192013.25872-1-radhakrishna.sripada@intel.com
Now the dma_slave_map is available for PXA architecture, switch the SSP
device to it.
This specifically means that :
- for platform data based machines, the DMA requestor channels are
extracted from the slave map, where pxa-ssp-dai.<N> is a 1-1 match to
ssp.<N>, and the channels are either "rx" or "tx".
- for device tree platforms, the dma node should be hooked into the
pxa2xx-ac97 or pxa-ssp-dai node.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Daniel Mack <daniel@zonque.org>
As the last driver using the former mechanism to acquire the DMA
requestor line has be converted to the dma_slave_map, remove all these
resources from the PXA devices.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Add some documentation for the pxad_param structure, and describe the
contract behind the minimal required priority of a DMA channel.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vinod Koul <vkoul@kernel.org>
As the pxa architecture switched towards the dmaengine slave map, the
old compatibility mechanism to acquire the dma requestor line number and
priority are not needed anymore.
This patch simplifies the dma resource acquisition, using the more
generic function dma_request_slave_channel().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
As the pxa architecture switched towards the dmaengine slave map, the
old compatibility mechanism to acquire the dma requestor line number and
priority are not needed anymore.
This patch simplifies the dma resource acquisition, using the more
generic function dma_request_slave_channel().
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
As the pxa architecture switched towards the dmaengine slave map, the
old compatibility mechanism to acquire the dma requestor line number and
priority are not needed anymore.
This patch simplifies the dma resource acquisition, using the more
generic function dma_request_slave_channel().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As the pxa architecture switched towards the dmaengine slave map, the
old compatibility mechanism to acquire the dma requestor line number and
priority are not needed anymore.
This patch simplifies the dma resource acquisition, using the more
generic function dma_request_slave_channel().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
As what former drcmr -1 value meant, add a this as a default to each
channel, ie. that by default no requestor line is used.
This is specifically used for network drivers smc91x and smc911x, and
needed for their port to slave maps.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vinod Koul <vkoul@kernel.org>
In order to remove the specific knowledge of the dma mapping from PXA
drivers, add a default slave map for pxa architectures.
This is the first step, and once all drivers are converted,
pxad_filter_fn() will be made static, and the DMA resources removed from
device.c.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reported-by: Arnd Bergmann <arnd@arndb.de>
In order to remove the specific knowledge of the dma mapping from PXA
drivers, add a default slave map for pxa architectures.
This won't impact MMP architecture, but is aimed only at all PXA boards.
This is the first step, and once all drivers are converted,
pxad_filter_fn() will be made static, and the DMA resources removed from
device.c.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
This patch replaces the ib_device_attr.max_sge with max_send_sge and
max_recv_sge. It allows ulps to take advantage of devices that have very
different send and recv sge depths. For example cxgb4 has a max_recv_sge
of 4, yet a max_send_sge of 16. Splitting out these attributes allows
much more efficient use of the SQ for cxgb4 with ulps that use the RDMA_RW
API. Consider a large RDMA WRITE that has 16 scattergather entries.
With max_sge of 4, the ulp would send 4 WRITE WRs, but with max_sge of
16, it can be done with 1 WRITE WR.
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Selvin Xavier <selvin.xavier@broadcom.com>
Acked-by: Shiraz Saleem <shiraz.saleem@intel.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Before goto err2, the variable qp is checked. So it is not necessary
to check qp in label err2.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Set the vlan flag and vlan_id field in the wc for rdma_listen()
to work over VLAN. This is required by ib_init_ah_attr_from_wc()
which is called by the CM REQ handler.
Signed-off-by: Vijay Immanuel <vijayi@attalasystems.com>
Reviewed-by: Yonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Increase the max MR limit to support more I/O queues
for NVMe over Fabrics hosts.
Signed-off-by: Vijay Immanuel <vijayi@attalasystems.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Fixes the following sparse warning:
drivers/ata/ahci_mvebu.c:85:5: warning:
symbol 'ahci_mvebu_stop_engine' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently smatch warns of possible Spectre-V1 issue in ahci_led_store():
drivers/ata/libahci.c:1150 ahci_led_store() warn: potential spectre issue 'pp->em_priv' (local cap)
Userspace controls @pmp from following callchain:
em_message->store()
->ata_scsi_em_message_store()
-->ap->ops->em_store()
--->ahci_led_store()
After the mask+shift @pmp is effectively an 8b value, which is used to
index into an array of length 8, so sanitize the array index.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
A number of resources remain powered to support hotplug. On platforms
I've worked with, allowing the ahci_platform to suspend saves about
150mW. This patch enables rpm and allows the device to be auto-suspended
through sysfs.
Signed-off-by: Samuel Morris <samorris@lexmark.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This change balances out the final ahci_port_resume in port_start to
ensure reference counts are correct after port stop.
Signed-off-by: Samuel Morris <samorris@lexmark.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Amber Lake uses the same gen graphics as Kaby Lake, including a id
that were previously marked as reserved on Kaby Lake, but that
now is moved to AML page.
So, let's just move it to AML macro that will feed into KBL macro
just to keep it better organized to make easier future code review
but it will be handled as a KBL.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614233720.30517-2-jose.souza@intel.com
Whiskey Lake uses the same gen graphics as Coffe Lake, including some
ids that were previously marked as reserved on Coffe Lake, but that
now are moved to WHL page.
So, let's just move them to WHL macros that will feed into CFL macro
just to keep it better organized to make easier future code review
but it will be handled as a CFL.
v2:
Fixing GT level of some ids
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614233720.30517-1-jose.souza@intel.com
Run the completer task to post a work completion after processing
a memory registration or invalidate work request. This covers the
case where the memory registration or invalidate was the last work
request posted to the qp.
Signed-off-by: Vijay Immanuel <vijayi@attalasystems.com>
Reviewed-by: Yonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>