Update xgbe-phy-v2.c to make use of the auto-negotiation (AN) phy hooks
to improve the ability to successfully complete Clause 73 AN when running
at 10gbps. Hardware can sometimes have issues with CDR lock when the
AN DME page exchange is being performed.
The AN and KR training hooks are used as follows:
- The pre AN hook is used to disable CDR tracking in the PHY so that the
DME page exchange can be successfully and consistently completed.
- The post KR training hook is used to re-enable the CDR tracking so that
KR training can successfully complete.
- The post AN hook is used to check for an unsuccessful AN which will
increase a CDR tracking enablement delay (up to a maximum value).
Add two debugfs entries to allow control over use of the CDR tracking
workaround. The debugfs entries allow the CDR tracking workaround to
be disabled and determine whether to re-enable CDR tracking before or
after link training has been initiated.
Also, with these changes the receiver reset cycle that is performed during
the link status check can be performed less often.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hooks to the driver auto-negotiation (AN) flow to allow the different
phy implementations to perform any steps necessary to improve AN.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must validate sockaddr_len, otherwise userspace can pass fewer data
than we expect and we end up accessing invalid data.
Fixes: 224cf5ad14 ("ppp: Move the PPP drivers")
Reported-by: syzbot+4f03bdf92fdf9ef5ddab@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check sockaddr_len before dereferencing sp->sa_protocol, to ensure that
it actually points to valid data.
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Reported-by: syzbot+a70ac890b23b1bf29f5c@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 192dc405f3 ("selftests: net: add tcp_mmap program")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If WOL event happened once, the LED[2] interrupt pin will not be
cleared unless we read the CSISR register. If interrupts are in use,
the normal interrupt handling will clear the WOL event. Let's clear the
WOL event before enabling it if !phy_interrupt_is_valid().
Signed-off-by: Jingju Hou <Jingju.Hou@synaptics.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function dca_common_get_tag is local to the source and does not need to be
in global scope, so make it static.
Cleans up sparse warning:
drivers/dca/dca-core.c:273:4: warning: symbol 'dca_common_get_tag' was
not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NPU has a limited number of address translation shootdown (ATSD)
registers and the GPU has limited bandwidth to process ATSDs. This can
result in contention of ATSD registers leading to soft lockups on some
threads, particularly when invalidating a large address range in
pnv_npu2_mn_invalidate_range().
At some threshold it becomes more efficient to flush the entire GPU
TLB for the given MM context (PID) than individually flushing each
address in the range. This patch will result in ranges greater than
2MB being converted from 32+ ATSDs into a single ATSD which will flush
the TLB for the given PID on each GPU.
Fixes: 1ab66d1fba ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Tested-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is a single npu context per set of callback parameters. Callers
should be prevented from overwriting existing callback values so
instead return an error if different parameters are passed.
Fixes: 1ab66d1fba ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Mark Hairgrove <mhairgrove@nvidia.com>
Tested-by: Mark Hairgrove <mhairgrove@nvidia.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pnv_npu2_init_context() and pnv_npu2_destroy_context() functions
are used to allocate/free contexts to allow address translation and
shootdown by the NPU on a particular GPU. Context initialisation is
implicitly safe as it is protected by the requirement mmap_sem be held
in write mode, however pnv_npu2_destroy_context() does not require
mmap_sem to be held and it is not safe to call with a concurrent
initialisation for a different GPU.
It was assumed the driver would ensure destruction was not called
concurrently with initialisation. However the driver may be simplified
by allowing concurrent initialisation and destruction for different
GPUs. As npu context creation/destruction is not a performance
critical path and the critical section is not large a single spinlock
is used for simplicity.
Fixes: 1ab66d1fba ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Mark Hairgrove <mhairgrove@nvidia.com>
Tested-by: Mark Hairgrove <mhairgrove@nvidia.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Don't do this via custom code, instead now that we have support in the
arch hotplug/hotunplug code, rely on those routines to do the right
thing.
The existing flush doesn't work because it uses ppc64_caches.l1d.size
instead of ppc64_caches.l1d.line_size.
Fixes: 9d5171a8f2 ("powerpc/powernv: Enable removal of memory for in memory tracing")
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds support for flushing potentially dirty cache lines
when memory is hot-plugged/hot-un-plugged. The support is currently
limited to 64 bit systems.
The bug was exposed when mappings for a device were actually
hot-unplugged and plugged in back later. A similar issue was observed
during the development of memtrace, but memtrace does it's own
flushing of region via a custom routine.
These patches do a flush both on hotplug/unplug to clear any stale
data in the cache w.r.t mappings, there is a small race window where a
clean cache line may be created again just prior to tearing down the
mapping.
The patches were tested by disabling the flush routines in memtrace
and doing I/O on the trace file. The system immediately
checkstops (quite reliablly if prior to the hot-unplug of the memtrace
region, we memset the regions we are about to hot unplug). After these
patches no custom flushing is needed in the memtrace code.
Fixes: 9d5171a8f2 ("powerpc/powernv: Enable removal of memory for in memory tracing")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Acked-by: Reza Arbab <arbab@linux.ibm.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current mail address is rejected, last activity (with a different
address) in git-history is from 2012. Remove this.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes a spelling error found in Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove cite "Not sure what this does, but it is absolutely essential".
Extract initialization of trackstick part when touchpad is in passthrough
mode for v3 and v6 protocols into own function. Initialization for v3 is:
setscale11, setscale11, setscale11, nibble 0x9, nibble 0x4. Initialization
for v6 is: setscale11, setscale11, setscale11, setrate 0xC8, setrate 0x14.
Nibbles 0x9 and 0x4 for v3 protocol correspond to setrate 0xC8 and 0x14,
therefore these sequences are same.
When touchpad is in passthrough mode, then OS communicates with trackstick
and this sequence is some magic vendor PS/2 command to put trackstick into
"extended" mode. After that sequence trackstick starts reporting packets in
some vendor 4 bytes format (first byte is always 0xE8).
Next step after configuring trackstick to be in "extended" mode, is to
configure touchpad for v3 protocol to expect that trackstick reports data
in "extended" mode. For v3 protocol this is done by setting bit 1 in
register 0xC2C8 (offset 0x08 from base address 0xC2C0).
When both touchpad and trackstick are not configured for "extended" mode
then touchpad reports trackstick packets in different format, which is not
supported by psmouse/alps driver (yet).
In Cirque documentation GP-AN- 130823 INTERFACING TO GEN4 OVER I2C (PDF)
available at http://www.cirque.com/gen4-dev-resources is Logical Address
0xC2C8 named as PS2AuxControl and Bit Number 1 as ProcessAuxExtendedData
with description: Auxiliary device data is assumed to be extended data when
set.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
John Fastabend says:
====================
While testing sockmap with more programs (besides our test programs)
I found a couple issues.
The attached series fixes an issue where pinned maps were not
working correctly, blocking sockets returned zero, and an error
path that when the sock hit an out of memory case resulted in a
double page_put() while doing ingress redirects.
See individual patches for more details.
v2: Incorporated Daniel's feedback to use map ops for uref put op
which also fixed the build error discovered in v1.
v3: rename map_put_uref to map_release_uref
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In the case where the socket memory boundary is hit the redirect
path returns an ENOMEM error. However, before checking for this
condition the redirect scatterlist buffer is setup with a valid
page and length. This is never unwound so when the buffers are
released latter in the error path we do a put_page() and clear
the scatterlist fields. But, because the initial error happens
before completing the scatterlist buffer we end up with both the
original buffer and the redirect buffer pointing to the same page
resulting in duplicate put_page() calls.
To fix this simply move the initial configuration of the redirect
scatterlist buffer below the sock memory check.
Found this while running TCP_STREAM test with netperf using Cilium.
Fixes: fa246693a1 ("bpf: sockmap, BPF_F_INGRESS flag for BPF_SK_SKB_STREAM_VERDICT")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In the recvmsg handler we need to add a wait event to support the
blocking use cases. Without this we return zero and may confuse
user applications. In the wait event any data received on the
sk either via sk_receive_queue or the psock ingress list will
wake up the sock.
Fixes: fa246693a1 ("bpf: sockmap, BPF_F_INGRESS flag for BPF_SK_SKB_STREAM_VERDICT")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Relying on map_release hook to decrement the reference counts when a
map is removed only works if the map is not being pinned. In the
pinned case the ref is decremented immediately and the BPF programs
released. After this BPF programs may not be in-use which is not
what the user would expect.
This patch moves the release logic into bpf_map_put_uref() and brings
sockmap in-line with how a similar case is handled in prog array maps.
Fixes: 3d9e952697 ("bpf: sockmap, fix leaking maps with attached but not detached progs")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This adds a reference to the dts of the Raspberry Pi 3 B+
in arm, so don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Per Documentation/bpf/bpf_devel_QA.txt add the -target flag to the
sockmap Makefile. Relevant text quoted here,
Otherwise, you can use bpf target. Additionally, you _must_ use
bpf target when:
- Your program uses data structures with pointer or long / unsigned
long types that interface with BPF helpers or context data
structures. Access into these structures is verified by the BPF
verifier and may result in verification failures if the native
architecture is not aligned with the BPF architecture, e.g. 64-bit.
An example of this is BPF_PROG_TYPE_SK_MSG require '-target bpf'
Fixes: 69e8cc134b ("bpf: sockmap sample program")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
BPF_PROG_TYPE_SK_MSG programs use a 'void *' for both data and the
data_end pointers. Additionally, the verifier ensures that every
accesses into the values is a __u64 read. This correctly maps on
to the BPF 64-bit architecture.
However, to ensure that when building on 32bit architectures that
clang uses correct types the '-target bpf' option _must_ be
specified. To make this clear add a note to the Documentation.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Before [1], When MAC address of the netdevice is changed, default GID is
supposed to get deleted and added back which affects the node and/or port
GUID in below sequence.
netdevice_event()
-> NETDEV_CHANGEADDR
default_del_cmd()
del_netdev_default_ips()
bond_delete_netdev_default_gids()
ib_cache_gid_set_default_gid()
ib_cache_gid_del()
add_cmd()
[..]
However, ib_cache_gid_del() was not getting invoked in non bonding
scenarios because event_ndev and rdma_ndev are same.
Therefore, fix such condition to ignore checking upper device when event
ndev and rdma_dev are same; similar to bond_set_netdev_default_gids().
Which this fix ib_cache_gid_del() is invoked correctly; however
ib_cache_gid_del() doesn't find the default GID for deletion because
find_gid() was given default_gid = false with
GID_ATTR_FIND_MASK_DEFAULT set.
But it was getting overwritten by ib_cache_gid_set_default_gid() later
on as part of add_cmd().
Therefore, mac address change used to work for default GID.
With refactor series [1], this incorrect behavior is detected.
Therefore,
when deleting default GID, set default_gid and set MASK flag.
when deleting IP based GID, clear default_gid and set MASK flag.
[1] https://patchwork.kernel.org/patch/10319151/
Fixes: 238fdf48f2 ("IB/core: Add RoCE table bonding support")
Fixes: 598ff6bae6 ("IB/core: Refactor GID modify code for RoCE")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When IPv6 link local address is removed, if it matches with the default
GID, default GID(s)s gets removed which may not be a desired behavior.
This behavior is introduced by refactor work in Fixes tag.
When IPv6 link address is removed, removing its equivalent RoCEv2 GID
which exactly matches with default RoCEv2 GID, is right thing to do.
However achieving it correctly requires lot more changes, likely in
roce_gid_mgmt.c and core/cache.c. This should be done as independent
patch.
Therefore, this patch preserves behavior of not deleteing default GIDs.
This is done by providing explicit hint to consider default GID property
using mask and default_gid; similar to add_gid().
Fixes: 598ff6bae6 ("IB/core: Refactor GID modify code for RoCE")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Default GIDs are marked reserved at the start of the GID table at index
0 and 1 by gid_table_reserve_default(). Currently when default GID is
requested, it can still allocates an empty slot which was not marked as
RESERVED for default GID, which is incorrect.
At least in current code flow of roce_gid_mgmt.c, in theory we can
still request to allocate more than one/two default GIDs depending
on how upper devices are setup.
Therefore, it is better for cache layer to only allow our reserved slots
to be used by default GID allocation requests.
Fixes: 598ff6bae6 ("IB/core: Refactor GID modify code for RoCE")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Running bpf programs requires disabled preemption,
however at least some* of the BPF_PROG_RUN_ARRAY users
do not follow this rule.
To fix this bug, and also to make it not happen in the future,
let's add explicit preemption disabling/re-enabling
to the __BPF_PROG_RUN_ARRAY code.
* for example:
[ 17.624472] RIP: 0010:__cgroup_bpf_run_filter_sk+0x1c4/0x1d0
...
[ 17.640890] inet6_create+0x3eb/0x520
[ 17.641405] __sock_create+0x242/0x340
[ 17.641939] __sys_socket+0x57/0xe0
[ 17.642370] ? trace_hardirqs_off_thunk+0x1a/0x1c
[ 17.642944] SyS_socket+0xa/0x10
[ 17.643357] do_syscall_64+0x79/0x220
[ 17.643879] entry_SYSCALL_64_after_hwframe+0x42/0xb7
Signed-off-by: Roman Gushchin <guro@fb.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
It's called v4l2_fwnode_endpoint_parse, not v4l2_fwnode_parse_endpoint.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Raspberry Pi 3 B+ has a Microchip LAN7515 (connect via USB) and
a Cypress CYW43455 (connect via UART). This patch enables the necessary
drivers.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
The Raspberry Pi 3 B+ has a Microchip LAN7515 (connect via USB) and
a Cypress CYW43455 (connect via UART). This patch enables the necessary
drivers.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
In order to gain more test coverage (e.g. Kernel CI) enable
the VCHIQ driver.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch enables the necessary driver for Raspberry Pi 3 B+,
which has a LAN7515 chip.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:
1) Fix SIP conntrack with phones sending session descriptions for different
media types but same port numbers, from Florian Westphal.
2) Fix incorrect rtnl_lock mutex logic from IPVS sync thread, from Julian
Anastasov.
3) Skip compat array allocation in ebtables if there is no entries, also
from Florian.
4) Do not lose left/right bits when shifting marks from xt_connmark, from
Jack Ma.
5) Silence false positive memleak in conntrack extensions, from Cong Wang.
6) Fix CONFIG_NF_REJECT_IPV6=m link problems, from Arnd Bergmann.
7) Cannot kfree rule that is already in list in nf_tables, switch order
so this error handling is not required, from Florian Westphal.
8) Release set name in error path, from Florian.
9) include kmemleak.h in nf_conntrack_extend.c, from Stepheh Rothwell.
10) NAT chain and extensions depend on NF_TABLES.
11) Out of bound access when renaming chains, from Taehee Yoo.
12) Incorrect casting in xt_connmark leads to wrong bitshifting.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net/ipv6: couple of fixes for rcu change to from
So many details... I am thankful for all the robots running the
permutations and tools.
Two bug fixes from the rcu change to rt->from:
1. missing rcu lock in ip6_negative_advice
2. rcu dereferences in 2 sites
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild test robot reported 2 uses of rt->from not properly accessed
using rcu_dereference:
1. add rcu_dereference_protected to rt6_remove_exception_rt and make
sure it is always called with rcu lock held.
2. change rt6_do_redirect to take a reference on 'from' when accessed
the first time so it can be used the sceond time outside of the lock
Fixes: a68886a691 ("net/ipv6: Make from in rt6_info rcu protected")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Raspberry Pi 3 B+ has the following major differences compared
to the model 3 B:
* Microchip LAN7515 (Gigabit Ethernet with integrated USB 2.0 HUB)
* Cypress CYW43455 (802.11n/ac and BT 4.2)
We need to add the USB LAN chip so the bootloader can add the MAC address.
This is necessary because there ain't an EEPROM or a valid OTP.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
This adds the root properties for the Raspberry Pi 3 B+
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
After commit a98d90e7d5 ("gpio: raspberrypi-exp: Driver for RPi3 GPIO
expander via mailbox service") we are able to control the rest of the
GPIOs of the RPi 3. So add all the missing parts (ACT LED,
Wifi & BT control, HDMI detect) to the DT.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
All RPi 1 and 2 boards used the PWM (audio out) on pin 40 and 45.
So it was easy to define them in bcm2835-rpi.dtsi. Starting with RPi 3
this wont work anymore, because it uses pin 40 and 41. Furthermore the
Zero variants doesn't have audio out.
This patch fixes this pin conflict by moving the PWM node to the board-level.
Change summary:
RPi 3 B: PWM1 45 -> 41
Zero, Zero W: PWM disabled
all other: no functional change
Reported-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
The current Cadence QSPI driver caused a kernel panic when loading
a Root Filesystem from QSPI. The problem was caused by reading more
bytes than needed because the QSPI operated on 4 bytes at a time.
<snip>
[ 7.947754] spi_nor_read[1048]:from 0x037cad74, len 1 [bfe07fff]
[ 7.956247] cqspi_read[910]:offset 0x58502516, buffer=bfe07fff
[ 7.956247]
[ 7.966046] Unable to handle kernel paging request at virtual
address bfe08002
[ 7.973239] pgd = eebfc000
[ 7.975931] [bfe08002] *pgd=2fffb811, *pte=00000000, *ppte=00000000
</snip>
Notice above how only 1 byte needed to be read but by reading 4 bytes
into the end of a mapped page, an unrecoverable page fault occurred.
This patch uses a temporary buffer to hold the 4 bytes read and then
copies only the bytes required into the buffer. A min() function is
used to limit the length to prevent buffer overflows.
Request testing of this patch on other platforms. This was tested
on the Intel Arria10 SoCFPGA DevKit.
Fixes: 0cf1725676 ("mtd: spi-nor: cqspi: Fix build on arches missing readsl/writesl")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This patch initialize stack variables which are used in
frag_lowpan_compare_key to zero. In my case there are padding bytes in the
structures ieee802154_addr as well in frag_lowpan_compare_key. Otherwise
the key variable contains random bytes. The result is that a compare of
two keys by memcmp works incorrect.
Fixes: 648700f76b ("inet: frags: use rhashtables for reassembly units")
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Reported-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
We already allocated the device and platform data at this
point. Instead of simply return from the probe function we
need to cleanup the resources first.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Xue Liu <liuxuenetmail@gmail.com>
atusb_probe() is never called in atomic context.
This function is only set as ".probe" in struct usb_driver.
Despite never getting called from atomic context,
atusb_probe() calls usb_alloc_urb() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
The hardware has a single block for applying a CTM prior to gamma lut.
It can be fed with pixels from one of our CRTC at a time and uses a
matrix with S0.9 scalars. Use private atomic state to reject attempts
from userland to apply CTM for more than one CRTC at a time and reject
matrices with scalars that we can't approximate without integer bits.
Signed-off-by: Stefan Schake <stschake@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/218067/
Assigning subdev flags in probe() after v4l2_i2c_subdev_init() clears the
I2C flag set by that function. Fix this by using bitwise or instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>