The filename of am35x-phy-control.h is confusing. The header is used
by the am335x phy driver, but the filename refers to am35x. Even worse
there is indeed another device called am35x but it does not use this
header at all.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
From: Ryo Kodama <ryo.kodama.vz@renesas.com>
When period_ns is set to the same value of RCAR_PWM_MAX_CYCLE in
rcar_pwm_get_clock_division(), this function should allow such value
for improving accuracy of frequency division setting.
Signed-off-by: Ryo Kodama <ryo.kodama.vz@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Instead of silent acceptance of unsupported requested configuration
for PWM period and setting the boundary supported value, return
-ERANGE to a caller.
Duty period value equal to 0 or period is still accepted to allow
configuration by PWM sysfs interface, when it is set to 0 by default.
For reference this is a list of restrictions on period_ns == 1/freq:
| PWM parent clock | parent clock divisor | max freq | min freq |
+------------------+----------------------+----------+----------+
| HCLK == 13 MHz | 1 (min) | 50.7 KHz | 198.3 Hz |
| HCLK == 13 MHz | 15 (max) | 3.38 KHz | 13.22 Hz |
| RTC == 32.7 KHz | 1 (min) | 128 Hz | 0.5 Hz |
| RTC == 32.7 KHz | 15 (max) | 8.533 Hz | 0.033 Hz |
Note that PWM sysfs interface does not support setting of period more
than NSEC_PER_SEC / MAX_INT32 ~ 2 seconds, however this PWM controller
supports a period up to 30 seconds.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The change fixes a problem, if duty_ns is too small in comparison
to period_ns (as a valid corner case duty_ns is 0 ns), then due to
PWM_DUTY() macro applied on a value the result is overflowed over 8
bits, and instead of the highest bitfield duty cycle value 0xff the
invalid duty cycle bitfield value 0x00 is written.
For reference the LPC32xx spec defines PWMx_DUTY bitfield description
is this way and it seems to be correct:
[Low]/[High] = [PWM_DUTY]/[256-PWM_DUTY], where 0 < PWM_DUTY <= 255.
In addition according to my oscilloscope measurements LPC32xx PWM is
"tristate" in sense that it produces a wave with floating min/max
voltage levels for different duty cycle values, for corner cases:
PWM_DUTY == 0x01 => signal is in range from -1.05v to 0v
....
PWM_DUTY == 0x80 => signal is in range from -0.75v to +0.75v
....
PWM_DUTY == 0xff => signal is in range from 0v to +1.05v
PWM_DUTY == 0x00 => signal is around 0v, PWM is off
Due to this peculiarity on very long period ranges (less than 1KHz)
and odd pre-divider values PWM generated wave does not remind a
clock shape signal, but rather a heartbit shape signal with positive
and negative peaks, so I would recommend to use high-speed HCLK clock
as a PWM parent clock and avoid using RTC clock as a parent.
The change corrects PWM output in corner cases and prevents any
possible overflows in calculation of values for PWM_DUTY and
PWM_RELOADV bitfields, thus helper macro definitions may be removed.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
As a preparatory change for switching LPC32xx mach support to common
clock framework fix clk_enable/clk_disable calls without matching
clk_prepare/clk_unprepare.
The driver can not be used on a platform with common clock framework
until clk_prepare/clk_unprepare calls are added, otherwise clk_enable
calls will fail and a WARN is generated:
# echo 1 > /sys/bus/platform/drivers/lpc32xx-pwm/4005c000.pwm/pwm/pwmchip0/pwm0/enable
------------[ cut here ]------------
WARNING: CPU: 0 PID: 701 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
Modules linked in: sc16is7xx
CPU: 0 PID: 701 Comm: sh Tainted: G W 4.3.0-rc2+ #171
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (lpc32xx_pwm_enable+0x1c/0x40)
[<>] (lpc32xx_pwm_enable) from [<>] (pwm_enable+0x48/0x5c)
[<>] (pwm_enable) from [<>] (pwm_enable_store+0x5c/0x78)
[<>] (pwm_enable_store) from [<>] (dev_attr_store+0x20/0x2c)
[<>] (dev_attr_store) from [<>] (sysfs_kf_write+0x44/0x50)
[<>] (sysfs_kf_write) from [<>] (kernfs_fop_write+0x134/0x194)
[<>] (kernfs_fop_write) from [<>] (__vfs_write+0x34/0xdc)
[<>] (__vfs_write) from [<>] (vfs_write+0xb8/0x140)
[<>] (vfs_write) from [<>] (SyS_write+0x50/0x90)
[<>] (SyS_write) from [<>] (ret_fast_syscall+0x0/0x38)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
LPC32xx SoC has two independent PWM controllers, they have different
clock parents, clock gates and even slightly different controls, and
each of these two PWM controllers has one output channel. Due to
almost similar controls arranged in a row it is incorrectly set that
there is one PWM controller with two channels, fix this problem, which
at the moment prevents separate configuration of different clock
parents and gates for both PWM controllers.
The change makes previous PWM device node description incompatible
with this update.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
NXP LPC32xx SoC has two separate PWM controller devices, update device
tree binding documentation to reflect this fact.
The change makes previous PWM device node description incompatible
with the new version.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The change removes '0x' from a device node address and uses lower case
hex chars.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Anjali Singhai Jain says:
====================
Add support for Geneve udp port offload
This patch series adds new ndo ops for Geneve add/del port, so as
to help offload Geneve tunnel functionalities such as RX checksum,
RSS, filters etc.
i40e driver has been tested with the changes to make sure the offloads
happen.
We do understand that this is not the ideal solution and most likely
will be redone with a more generic offload framework.
But this certainly will enable us to start seeing benefits of the
accelerations for Geneve tunnels.
As a side note, we did find an existing issue in i40e driver where a
service task can modify tunnel data structures with no locks held to
help linearize access. A separate patch will be taking care of that issue.
A question out to the community is regarding the driver Kconfig parameters
for VxLAN and Geneve, it would be ideal to drop those if there is a way
to help resolve vxlan/geneve_get_rx_port symbols while the tunnel modules
are not loaded.
Performance numbers:
With the offloads enable on X722 devices with remote checksum enabled
and no other tuning in terms of cpu governer etc on my test machine:
With offload
Throughput: 5527Mbits/sec with a single thread
%cpu: ~43% per core with 4 threads
Without offload
Throughput: 2364Mbits/sec with a single thread
%cpu: ~99% per core with 4 threads
These numbers will get better for X722 as it is being worked. But
this does bring out the delta in terms of when the stack is notified
with csum_level 1 and CHECKSUM_UNNECESSARY vs not without the RX offload.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a call to geneve_get_rx_port in i40e so that when it
comes up it can learn about the existing geneve tunnels.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an op that the drivers can call into to get existing
geneve ports.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the Kconfig file with dependency for supporting GENEVE tunnel
offloads.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds driver hooks to implement ndo_ops to add/del
udp port in the HW to identify GENEVE tunnels.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ndo_ops to add/del UDP ports to a device that supports geneve
offload.
v2: Comment fix.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we all know, the value of pf_retrans >= max_retrans_path can
disable pf state. The variables of pf_retrans and max_retrans_path
can be changed by the userspace application.
Sometimes the user expects to disable pf state while the 2
variables are changed to enable pf state. So it is necessary to
introduce a new variable to disable pf state.
According to the suggestions from Vlad Yasevich, extra1 and extra2
are removed. The initialization of pf_enable is added.
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Zhu Yanjun <zyjzyj2000@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A FTM PWM instance enables/disables three clocks: The bus clock, the
counter clock and the PWM clock. The bus clock gets enabled on
pwm_request, whereas the counter and PWM clocks will be enabled upon
pwm_enable.
The driver has three closesly related issues when enabling/disabling
clocks during suspend/resume:
- The three clocks are not treated differently in regards to the
individual PWM state enabled/requested. This can lead to clocks
getting disabled which have not been enabled in the first place
(a PWM channel which only has been requested going through
suspend/resume).
- When entering suspend, the current behavior relies on the
FTM_OUTMASK register: If a PWM output is unmasked, the driver
assumes the clocks are enabled. However, some PWM instances
have only 2 channels connected (e.g. Vybrid's FTM1). In that case,
the FTM_OUTMASK reads 0x3 if all channels are disabled, even if
the code wrote 0xff to it before. For those PWM instances, the
current approach to detect enabled PWM signals does not work.
- A third issue applies to the bus clock only, which can get enabled
multiple times (once for each PWM channel of a PWM chip). This is
fine, however when entering suspend mode, the clock only gets
disabled once.
This change introduces a different approach by relying on the enable
and prepared counters of the clock framework and using the frameworks
PWM signal states to address all three issues.
Clocks get disabled during suspend and back enabled on resume
regarding to the PWM channels individual state (requested/enabled).
Since we do not count the clock enables in the driver, this change no
longer clears the Status and Control registers Clock Source Selection
(FTM_SC[CLKS]). However, since we disable the selected clock anyway,
and we explicitly select the clock source on reenabling a PWM channel
this approach should not make a difference in practice.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Setting of PWM_SW_UPDATE is bit different in Intel Broxton compared to the
previous generation SoCs. Previously it was OK to set the bit many times
(from userspace via sysfs for example) before the PWM is actually enabled.
Starting from Intel Broxton it seems that we must set PWM_SW_UPDATE only
once before the PWM is enabled. Otherwise it is possible that the PWM does
not start properly.
Change the sequence of how PWM_SW_UPDATE is programmed so that we only set
it in pwm_lpss_config() when the PWM is already enabled. The initial
setting of PWM_SW_UPDATE will be done when PWM gets enabled. This should
make the driver work with the previous generation Intel SoCs and Broxton.
Add also small delay after the bit is set to let the hardware propagate it
properly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
We have two users of core part right now. Let them to select core part
automatically.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
For Broxton PWM controller, base unit is defined as 8-bit integer
and 14-bit fraction, so need to update base unit setting to output
wave with right frequency.
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
It's possible that the PWM clock becomes an orphan. So better check the
result of clk_get_rate() in order to prevent a division by zero.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Currently pwm-bcm2835 assumes a fixed clock rate and stores the
resulting scaler in the driver structure. But with the upcoming
PWM clock support for clk-bcm2835 the rate could change, so
calculate the scaler in the ->config() callback.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
William Hua <william.hua@canonical.com> wrote:
>
> I wasn't aware there was an enforced minimum size. I simply set the
> nelem_hint in the rhastable_params struct to 1, expecting it to grow as
> needed. This caused a segfault afterwards when trying to insert an
> element.
OK we're doing the size computation before we enforce the limit
on min_size.
---8<---
We need to do the initial hash table size computation after we
have obtained the correct min_size/max_size parameters. Otherwise
we may end up with a hash table whose size is outside the allowed
envelope.
Fixes: a998f712f7 ("rhashtable: Round up/down min/max_size to...")
Reported-by: William Hua <william.hua@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Proper source for MFC block is mout_user_aclk333 (in datasheet named
USER_MUX_ACLK_333), not the output of CLKDIV_ACLK_333 MUX.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Fix cpu clock configuration data for Exynos5422/5800 SoCs
(they use higher PCLK_DBG divider values than Exynos5420 and
support additional frequencies).
Based on Hardkernel's kernel for ODROID-XU3 board.
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
With the addition of the new Samsung specific cpu-clock type, the
arm clock can be represented as a cpu-clock type. Add the CPU clock
configuration data and instantiate the CPU clock type for Exynos5420.
Changes by Bartlomiej:
- split Exynos5420 support from the original patches
- moved E5420_[EGL,KFC]_DIV0() macros to clk-exynos5420.c
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds clocks, which are required for preserving parent clock
configuration on GSCL power domain on/off.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The LPSS PWM driver calls pwm_lpss_disable() when the PWM device is
released (for example unexported from sysfs). This in turn calls
pm_runtime_put() which makes runtime PM count to be unbalanced if the
device has not been enabled at this point.
This is easy to reproduce:
# cd /sys/class/pwm/pwmchip0
# echo 0 > export
# echo 0 > unexport
The count is unbalanced and prevents the PWM device from being powered on
next time.
Fix this by removing ->free() callback. There are no resources to be
released anyway.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The GIC has no such thing as interrupt 1020: the last valid ID is
1019, and the range 1020-1023 is reserved - 1023 indicating that
no interrupt is pending. So let's make sure we don't try to handle
this ID.
This bug has been in since the initial GIC code was introduced in
8ad68bbf7a ("[ARM] Add support for ARM RealView board").
Reported-by: Eric Auger <eric.auger@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On the error path, the v2m drivers drops the refcount on the parent
node instead of doing it on the node that generated the error.
Humph...
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Instead of having the irqchip being a static struct, make it part
of the per-instance data so we can assign it a dynamic name. This
has the usable side effect of displaying the GIC with an instance
number as GIC0, GIC1 ... GICn in /proc/interrupts, which is helpful
when debugging cascaded GICs, such as on the ARM PB11MPCore.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The ARM RealView PB11MPCore reference design has some special
bits in a system controller register to set up the GIC in one
of three modes: legacy, new with DCC, new without DCC. The
register is also used to enable FIQ.
Since the platform will not boot unless this register is set
up to "new with DCC" mode, we need a special quirk to be
compiled-in for the RealView platforms.
If we find the right compatible string on the GIC TestChip,
we enable this quirk by looking up the system controller and
enabling the special bits.
We depend on the CONFIG_REALVIEW_DT Kconfig symbol as the old
boardfile code has the same fix hardcoded, and this is only
needed for the attempts to modernize the RealView code using
device tree.
After fixing this, the PB11MPCore boots with device tree
only.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The GIC bindings for the ARM11MPCore need to differentiate between
the GIC on the Test Chip and the one on the evaluation baseboard.
Split the binding in two and define new compatible-strings.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We almost have all the needed bits requiredable to create a irq domain
on top of a MSI domain.
For this, we enable a few things:
- the virq is stored in the msi_desc
- device, msi_alloc_info and domain-specific data
are stored in the platform_priv_data structure
- we introduce a new API for platform-msi:
/* Create a MSI-based domain */
struct irq_domain *
platform_msi_create_device_domain(struct device *dev,
unsigned int nvec,
irq_write_msi_msg_t write_msi_msg,
const struct irq_domain_ops *ops,
void *host_data);
/* Allocate MSIs in an MSI domain */
int platform_msi_domain_alloc(struct irq_domain *domain,
unsigned int virq,
unsigned int nr_irqs);
/* Free MSIs from an MSI domain */
void platform_msi_domain_free(struct irq_domain *domain,
unsigned int virq,
unsigned int nvec);
/* Obtain the host data passed to platform_msi_create_device_domain */
void *platform_msi_get_host_data(struct irq_domain *domain);
platform_msi_create_device_domain() is a hybrid of irqdomain creation
and interrupt allocation, creating a domain backed by the MSIs associated
to a device. IRQs can then be allocated in that domain using
platform_msi_domain_alloc().
This now allows a wired irq to MSI bridge to be created.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
To be able to allocate interrupts from the MSI layer down,
add a new msi_domain_populate_irqs entry point.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The .prepare callbacks are so far only called from msi_domain_alloc_irqs.
In order to reuse that code, split that code and create a
msi_domain_prepare_irqs function that the existing code can call into.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We are soon going to need the MSI layer to call into the domain
allocators. Instead of open coding this, make the standard
irq_domain_alloc_irqs_recursive function available to the MSI
layer.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we're going to have multiple paths to allocate/free the
platform-msi private data, factor this out into separate
utility functions.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
MSIs for a given device are normally all allocated in one go.
Make sure the internal code can allocate them one at a time
if required.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Updated the registers' values to enhance SATA performance and
reliability on ls1021a soc.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The PTC[RXWM] sets the watermark value for Rx FIFO. The default
value 0x20 might be insufficient for some hard drives. If the
watermark value is too small, a single-cycle overflow may occur
and is reported as a CRC or internal error in the PxSERR register.
Updated the value to 0x29 according to the validation test.
All LS platforms are affected.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Updated the registers' values to enhance SATA performance and
reliability.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Document that 'width' and 'height' are measured in millimeters.
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Kyocera TCG121XGLP panel is an XGA LCD TFT panel connected through
LVDS, which can be supported by the simple panel driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
