If the driver gets unloaded during reset recovery, it's possible
that it will attempt to free resources when they're already free.
Add a check to make sure that the Tx and Rx rings actually exist
before dereferencing them to free resources.
Change-ID: I4d2b7e9ede49f634d421a4c5deaa5446bc755eee
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When VFs are created, the MAC address defaults to all zeros, indicating
to the VF driver that it should use a random MAC address. However, the
PF driver was incorrectly adding this zero MAC to the filter table,
along with the VF's randomly generated MAC address.
Check for a good address before adding the default filter. While we're
at it, make the error message a bit more useful.
Change-ID: Ia100947d68140e0f73a19ba755cbffc3e79a8fcf
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The virtual channel interface was using incorrect semantics to remove
MAC addresses, which would leave incorrect filters active when using
VLANs. To correct this, add a new function that unconditionally removes
MAC addresses from all VLANs, and call this function when the VF
requests a MAC filter removal.
Change-ID: I69826908ae4f6c847f5bf9b32f11faa760189c74
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
BIT_ULL was used on a u32 or less where it can simply be BIT. This
fixes some trivial static analyzer warnings. Chomp, chomp.
Tested with objdump of binary before and after, no changes to code.
Change-ID: I6245e9abd447192dbde1669c747aeb2878126c7d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stop reporting KEY_SLEEP for a short key-press and report KEY_POWER instead
This change applies to both DA9063 and DA9062 ONKEY drivers.
A previous application used for testing by the developer required a
KEY_SLEEP and KEY_POWER input_report_key event to distinguish between a
short and long key-press of the power key. This is not the general
convention and the typical solution is for KEY_POWER to be used in both
cases: suspend and S/W power off.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that was
just added in 4.4, or that has been broken for many years without anyone
noticing.
at91/sama5d2
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin
- fix incorrect clock input for SDIO
exynos
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx
- Fix vf610 SAI clock configuration bug which is discovered by
the newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx
- fix prototypes for readl/writel functions
ls2080a
- use little-endian register access for GPIO and SDHCI
omap
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of
when MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa
- use PWM lookup table for all ezx machines
s3c24xx
- Remove incorrect __init annotation from s3c24xx cpufreq driver structures.
versatile
- fix PCI IRQ mapping on Versatile PB
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fgEd
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that
was just added in 4.4, or that has been broken for many years without
anyone noticing.
at91/sama5d2:
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin:
- fix incorrect clock input for SDIO
exynos:
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx:
- Fix vf610 SAI clock configuration bug which is discovered by the
newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx:
- fix prototypes for readl/writel functions
ls2080a:
- use little-endian register access for GPIO and SDHCI
omap:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of when
MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa:
- use PWM lookup table for all ezx machines
s3c24xx:
- Remove incorrect __init annotation from s3c24xx cpufreq driver
structures.
versatile:
- fix PCI IRQ mapping on Versatile PB"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ls2080a/dts: Add little endian property for GPIO IP block
dt-bindings: define little-endian property for QorIQ GPIO
ARM64: dts: ls2080a: fix eSDHC endianness
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: pxa: use PWM lookup table for all machines
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
ARM: ixp4xx: fix read{b,w,l} return types
irqchip/versatile-fpga: Fix PCI IRQ mapping on Versatile PB
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2015-12-12
This series contains updates to ixgbe only.
Alex Duyck provides almost off of the changes in this series. First, add a
check to make sure mac_table was actually allocated and is not NULL to
ensure we do not get a NULL pointer dereference further down the line.
Fixed SR-IOV VLAN pool configuration since the code for checking the PF bit
in ixgbe_set_vf_vlan_msg() was using the wrong offset. Cleanup/simplify
the logic for setting the VFTA register by removing the number of
conditional checks needed. Fixed a number of issues within the VLVF and
VLFB configuration by simplifying the code. Added support for bypassing
the VLVF entry creation when the PF is adding a new VLAN. Reduced the
complexity of the search function used for finding a VLVF entry associated
with a given VLAN ID. Added support for VLAN promiscuous with SR-IOV
enabled by setting all the bits in the VFTA and all of the VLVF bits
associated with teh pool belonging to the PF, in addition to cleaning up
those same bits in the event of promiscuous mode being disabled. Fixed
and issue where we ran the risk of leaking an address into pool 0 which
really belongs to VF 0 when SR-IOV is enabled.
Emil fixes an issue with some X550 devices which can connect at 2.5Gbps,
but only with certain link partners during fail-over, so to avoid
confusion, we do not report it as supported.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for renaming and hard links to the fs. Most of this can be
implemented by using simple library operations under the same constraints
that we don't use a reserved name like elsewhere. Linking can be useful
to share/manage things like maps across subsystem users. It works within
the file system boundary, but is not allowed for directories.
Symbolic links are explicitly not implemented here, as it can be better
done already by doing bind mounts inside bpf fs to set up shared directories
f.e. useful when using volumes in docker containers that map a private
working directory into /sys/fs/bpf/ which contains itself a bind mounted
path from the host's /sys/fs/bpf/ mount that is shared among multiple
containers. For single maps instead of whole directory, hard links can
be easily used to do the same.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
adding the spi-loopback-test module to Kconfig and Makefile
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver is submitting lots of distinct spi-messages messages
with all kinds of alignments and length pattern.
Also distinct kinds of transfer pattern tests are implemented
(rx, tx, rx/tx, tx+tx, tx+rx,...)
Right now on a raspberry pi 752 distinct spi_messages are executed
in 13 different scenarios.
Configuration of additional test-pattern is easy, so that when
new bugs in drivers get detected the relevant transfer pattern can
also get added to the test framework, so that such situations are
detected in other drivers as well.
The idea behind this driver is to make it possible to also detect
regressions in spi_master implementations when changes occur.
Potentially these tests could get executed automatically in a
test-server-farm.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the spi_loopback_test driver there is the need to initialize
a spi_message that is filled with values from a static structure.
Applying spi_message_init to such a prefilled structure results in
all the settings getting reset to zero, which is not what we want.
Copying each field of spi_message separately instead always includes
the risk that some new fields have not been implemented in the copying
code.
So here we introduce a version of spi_message_init called
spi_message_init_no_memset that does not fill the structure
with zero first, but only initializes the relevant list_heads.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When setting aside capacity for struct page it must be aligned to the
largest mapping size that is to be made available via DAX. Make the
alignment configurable to enable support for 1GiB page-size mappings.
The offset for PFN_MODE_RAM may now be larger than SZ_8K, so fixup the
offset check in nvdimm_namespace_attach_pfn().
Reported-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add support for PA gpio pin for controlling an external amplifier as used
on some Allwinner boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename the codec dapm widgets and routes with a _codec prefix. This is
a preparation patch for adding card dapm widgets and routes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DPCM does not fully support symmetry attributes. soc_pcm_apply_symmetry()
is skipped in soc_pcm_open() for DPCM, without being applied elsewhere.
So HW parameters cannot be correctly limited, and user space can do
playback/capture at different rates while HW actually does not support it.
soc_pcm_params_symmetry() will return error and the second stream stops.
This patch adds soc_pcm_apply_symmetry() for FE, BE, and codec DAIs
in DPCM path that was skipped in soc_pcm_open().
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
davinci_spi_bufs() uses wait_for_completion_interruptible()
without bothering to handle -ERESTARTSYS. Due to this,
sometime, it returns prematurely when a signal is received.
Since the return value is never checked, userspace eventually
receives a spurious -EIO.
To fix this, use un-interruptible wait_for_completion_timeout().
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add code to unregister codec in probe function,
when the error occurs after the codec is registered.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add binding document for Pistachio Internal DAC
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Locking is currently missing from the DSP firmware controls, which can
lead to some race conditions if the controls are accessed as the DSP
powers up or down. This patch adds them to the new power lock.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should hold the DSP power lock whilst changing the firmware since we
need to check if it is running first.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most events around the DSP just need to be locked to ensure that the DSP
can't change power state whilst they are happening. This includes the
debugfs entries and this will make sorting the rest of the locking
simpler.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for Texas Instruments pcm3168a codec
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add binding document for Texas Instruments pcm3168a codec
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add SOC_DOUBLE_STS macro for read-only volatile status controls
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the register defaults are provided by the driver without the
number by mistake, it should just return an error with one promotion.
This should be as early as possible, then there is no need to verify
the register defaults' stride and the other code followed.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If there is no cache used for the drivers, the register defaults
or the register defaults raw are not need any more. This patch
will check this and print a warning.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This new code is unreachable. Presumably there was supposed to be a
case statement there similar to the earlier code.
Fixes: afcc00b91f ('regmap: add 64-bit mode support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should cast these to 64bit so that we don't truncate away the high
bits.
Fixes: afcc00b91f ('regmap: add 64-bit mode support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These were supposed to be bitwise AND instead of logical. Also kernel
style is for the operator to be on the first line and I removed some
extra parenthesis.
Fixes: c90456e36d ('regulator: pv88090: new regulator driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_request_threaded_irq to ensure the irq is freed when unload the
module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSPI instances in Vybrid have a different amount of chip selects
and CTARs (Clock and transfer Attributes Register). In case of
DSPI1 we only have 2 CTAR registers and 4 CS. In present driver
implementation CTAR offset is derived from CS instance which will
lead to out of bound access if chip select instance is greater than
CTAR register instance, hence use single CTAR0 register for all CS
instances. Since we write the CTAR register anyway before each access,
there is no value in using the additional CTAR registers. Also one
should not program a value in CTAS for a CTAR register that is not
present, hence configure CTAS to use CTAR0.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
Explicitly set the transmit data level on the transceiver to 16 samples
rather then the default 0. This matches both the level set in the vendor
kernel and the (seemingly very similar) i2s engine. This fixes audio
glitches when playing back at 192k rate.
At the same time, fix a trivial typo in the TDL mask definition
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Attempting to use this codec driver triggers a BUG() in regcache_sync()
since no cache type is set. The register map of this device is fairly
small and has few holes so a flat cache is suitable.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
There is a need of a broadcast timer in this case to ensure proper
wakeup when the cpus are in sleep mode and a timer expires.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
These are all off by one; the playback and bypass switches are the top
two bits of the registers, which are at shifts 7 and 6 not 8 and 7.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- opal-irqchip: Fix double endian conversion from Alistair Popple
- cxl: Set endianess of kernel contexts from Frederic Barrat
- sbc8641: drop bogus PHY IRQ entries from DTS file from Paul Gortmaker
- Revert "powerpc/eeh: Don't unfreeze PHB PE after reset" from Andrew Donnellan
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bYj2
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- opal-irqchip: Fix double endian conversion from Alistair Popple
- cxl: Set endianess of kernel contexts from Frederic Barrat
- sbc8641: drop bogus PHY IRQ entries from DTS file from Paul Gortmaker
- Revert "powerpc/eeh: Don't unfreeze PHB PE after reset" from Andrew
Donnellan
* tag 'powerpc-4.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
Revert "powerpc/eeh: Don't unfreeze PHB PE after reset"
powerpc/sbc8641: drop bogus PHY IRQ entries from DTS file
cxl: Set endianess of kernel contexts
powerpc/opal-irqchip: Fix double endian conversion
Reference the newly added efuse clock-ids in the clock-tree.
Signed-off-by: ZhengShunQian <zhengsq@rock-chips.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the clock tree definition for the new rk3228 SoC.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the devicetree binding for the cru on the rk3228 which quite similar
structured as previous clock controllers.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add clock-ids for the two efuse blocks of the rk3288.
Signed-off-by: ZhengShunQian <zhengsq@rock-chips.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Merge misc fixes from Andrew Morton:
"17 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MIPS: fix DMA contiguous allocation
sh64: fix __NR_fgetxattr
ocfs2: fix SGID not inherited issue
mm/oom_kill.c: avoid attempting to kill init sharing same memory
drivers/base/memory.c: prohibit offlining of memory blocks with missing sections
tmpfs: fix shmem_evict_inode() warnings on i_blocks
mm/hugetlb.c: fix resv map memory leak for placeholder entries
mm: hugetlb: call huge_pte_alloc() only if ptep is null
kernel: remove stop_machine() Kconfig dependency
mm: kmemleak: mark kmemleak_init prototype as __init
mm: fix kerneldoc on mem_cgroup_replace_page
osd fs: __r4w_get_page rely on PageUptodate for uptodate
MAINTAINERS: make Vladimir co-maintainer of the memory controller
mm, vmstat: allow WQ concurrency to discover memory reclaim doesn't make any progress
mm: fix swapped Movable and Reclaimable in /proc/pagetypeinfo
memcg: fix memory.high target
mm: hugetlb: fix hugepage memory leak caused by wrong reserve count
