reduces unnecessary code duplication. Also takes the sc_pcu_lock within
ath_reset instead of callsites, which makes it possible to always cancel
all queued work items before the reset, possibly fixing a few race
conditions (work items vs reset) along with it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes it much easier to add further rework to avoid race conditions
between reset and other work items.
Move other functions to make ath_reset static.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helps with making ath_reset static in the next commit
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we already have ah->{rx,tx}chainmask for the same purpose
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The assumption is that during the hw config, transmission was
already stopped by mac80211. Sometimes the AP can be switching
b/w the ht modes due to intolerant or etc where STA is in
the middle of transmission. In such scenario, buffer overflow
was observed at driver side. And also before updating the rate
control, the frames are continued to xmited with older rates.
This patch ensures that the frames are always xmitted with
updated rates and avoid buffer overflow.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tx flow control for non-mesh modes of operation only needs to act on the
net device queues: when the hardware queues are full we stop accepting
traffic from the net device. In mesh, however, we also need to stop
forwarding traffic. This patch checks the hardware queues before
attempting to forward a mesh frame.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To check whether a frame is in the RMC, we need access to the mesh
header. This header is encrypted in encrypted data frames, so make this
check after the frame has been decrypted.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To properly maintain the peer's block ack window, the driver needs to be
able to control the new starting sequence number that is sent along with
the BlockAckReq frame.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rule to copy this file doesn't have to be forced. However
lib1funcs.[So] have to be listed amongst the targets.
This prevents zImage from being recreated needlessly.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Some old bootloaders can't be updated to a device tree capable one,
yet they provide ATAGs with memory configuration, the ramdisk address,
the kernel cmdline string, etc. To allow a device tree enabled
kernel to be used with such bootloaders, it is necessary to convert those
ATAGs into FDT properties and fold them into the DTB appended to zImage.
Currently the following ATAGs are converted:
ATAG_CMDLINE
ATAG_MEM
ATAG_INITRD2
If the corresponding information already exists in the appended DTB, it
is replaced, otherwise the required node is created to hold it.
The code looks for ATAGs at the location pointed by the value of r2 upon
entry into the zImage code. If no ATAGs are found there, an attempt at
finding ATAGs at the typical 0x100 offset from start of RAM is made.
Otherwise the DTB is left unchanged.
Thisstarted from an older patch from John Bonesio <bones@secretlab.ca>,
with contributions from David Brown <davidb@codeaurora.org>.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
This is a small subset of string functions needed by commits to come.
Except for memcpy() which is unchanged from its original location, their
implementation is meant to be small, and -Os is enforced to prevent gcc
from doing pointless loop unrolling.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
The appended DTB gets relocated with the decompressor code to get out
of the way of the decompressed kernel. However the kernel's .bss section
may be larger than the relocated code and data, and then the DTB gets
overwritten. Let's make sure the relocation takes care of moving zImage
far enough so no such conflict with .bss occurs.
Thanks to Tony Lindgren <tony@atomide.com> for figuring out this issue.
While at it, let's clean up the code a bit so that the wont_overwrite
symbol is used while determining if a conflict exists, making the above
change more precise as well as eliminating some ARM/THUMB alternates.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
This patch provides the ability to boot using a device tree that is appended
to the raw binary zImage (e.g. cat zImage <filename>.dtb > zImage_w_dtb).
Signed-off-by: John Bonesio <bones@secretlab.ca>
[nico: ported to latest zImage changes plus additional cleanups/improvements]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Reorder functions to remove the need for a forward declaration
introduced by the last commit.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: linux-wireless@vger.kernel.org
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function wiphy_update_regulatory() uses the static variable
last_request and thus needs to be called with reg_mutex held.
This is the case for all users in reg.c, but the function was
exported for use by wiphy_register(), from where it is called
without the lock being held.
Fix this by making wiphy_update_regulatory() private and introducing
regulatory_update() as a wrapper that acquires and holds the lock.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: linux-wireless@vger.kernel.org
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the incorrect indentation in functions fb_try_mode() and fb_find_mode().
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This is needed for proper alignment when the DTB appending feature
is used.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
The array size of fifo_size array in the global dispc struct is currently
hardcoded to 3. Replace this with the MAX_DSS_OVERLAYS macro in dss_features.h,
use dss_features function to get the number of overlays instead of the
ARRAY_SIZE macro in dispc_read_plane_fifo_sizes().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Iterate over overlay id's to shorten _dispc_set_color_conv_coef()
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Iterate over manager and overlay id's to shorten dispc_save_context() and
dispc_restore_context().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Iterate over manager and overlay id's to shorten dispc_dump_regs().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Prepare dispc_dump_regs() to iterate over manager and overlay id's. Doing this
requires modifications of the macro "DUMPREG" which currently needs us to specify
the manager/overlay name to get the correct result. For example, in order to
print the register DISPC_TIMING_H(OMAP_DSS_CHANNEL_LCD), we can't iterate over
a varaible i and get the desired result through DUMPREG(DISPC_TIMING_H(i)).
Split the registers into 3 sections, the first with no arguments(common
registers), the second with one argument(manager/overlay id), and the third with
two arguments(overlay id and coefficient index), redefine DUMPREG macros for
each of these.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Make the debug message useful by printing the name of the device
that no associated driver could be found for.
Signed-off-by: Andy Doan <andy.doan@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's no guarantee that the error handler worker thread
will run while the dispc clocks are on. Explicitly enable/disable
them.
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If a manager is moved while attached to an enabled display, the DSS
system will be left in an inconsistent state. This will eventually cause
a kernel oops when the enabled display is disabled.
Fix this by not allowing the user to move a manager away from an enabled
display.
Signed-off-by: Daniel Morsing <daniel.morsing@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
None of the DSS interface drivers check if an overlay manager is
connected to the display when the display is being enabled. This leads
to null pointer crash if the display has no manager.
This patch checks for the manager and returns an error if it is null.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix two problems in PicoDLP driver's error handling on
picodlp_panel_power_on:
- If omapdss_dpi_display_enable() failed, the its error value was not
returned
- If picodlp_i2c_init() failed, dssdev->state was erroneously set to
OMAP_DSS_DISPLAY_ACTIVE
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
PicoDLP is a micro projector from TI.
DLP used in OMAP4 is dpp2600 (DLP Pico Projector) The DLP requires
commands to be sent over i2c for configurations. To know more about
dpp2600 commands please visit:
https://focus.ti.com/myti/docs/extranet.tsp?sectionId=403
The picodlp module consists of a dss driver and an i2c_client.
To know more please visit:
http://www.omappedia.org/wiki/PicoDLP_projector_guide
Based on original design from Mythri P K <mythripk@ti.com>
Signed-off-by: Mayuresh Janorkar <mayur@ti.com>
Signed-off-by: Mythri P K <mythripk@ti.com>
[tomi.valkeinen@ti.com: squashed commits]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
No code altered at this point, simply preparing for upcoming
refactorizations.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move code from endpoint.c into a new file called stream.c and rename
functions so that their names actually reflect what they're doing.
This way, endpoint.c will be available to functions that hold all the
endpoint logic.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sort its entries in alphabetical order.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The endpoint usage field is described in the USB 2.0 specification,
chapter 9.6.6.
Also, move the sync type fields block down by some lines to reflect the
fact that these are also stuffed in bmAttributes.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without this patch it is possible to select the VIDEO_OMAP3
driver which then selects OMAP_IOVMM. But the omap iommu
driver is not compiled without IOMMU_SUPPORT enabled. Fix
that by forcing OMAP_IOMMU and OMAP_IOVMM are enabled before
VIDEO_OMAP3 can be selected.
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
There is a window in which the ioend that we call inode_dio_wake on
in xfs_end_io_direct_write is already free. Fix this by storing
the inode pointer in a local variable.
This is a fix for the regression introduced in 3.1-rc by
"fs: move inode_dio_done to the end_io handler".
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
del_timer_sync() can cause a deadlock when called in interrupt context.
It is used with on_each_cpu() in some parts for sysfs files like bank*,
check_interval, cmci_disabled and ignore_ce.
However, use of on_each_cpu() results in calling the function passed
as the argument in interrupt context. This causes a flood of nested
warnings from del_timer_sync() (it runs on each CPU) caused even by a
simple file access like:
$ echo 300 > /sys/devices/system/machinecheck/machinecheck0/check_interval
Fortunately, these MCE-specific files are rarely used and AFAIK only few
MCE geeks experience this warning.
To remove the warning, move timer deletion outside of the interrupt
context.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Start using the generic fault report mechanism, as provided by
the IOMMU core, and remove its now-redundant omap_iommu_set_isr API.
Currently we're only interested in letting upper layers know about the
fault, so in case the faulting device is a remote processor, they could
restart it.
Dynamic PTE/TLB loading is not supported.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Add iommu fault report mechanism to the IOMMU API, so implementations
could report about mmu faults (translation errors, hardware errors,
etc..).
Fault reports can be used in several ways:
- mere logging
- reset the device that accessed the faulting address (may be necessary
in case the device is a remote processor for example)
- implement dynamic PTE/TLB loading
A dedicated iommu_set_fault_handler() API has been added to allow
users, who are interested to receive such reports, to provide
their handler.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Apparently this doesn't always work reliably, e.g. at resume time.
Just initialize to 0, so the ring is considered empty.
Tested with hibernation on Sumo and Cayman cards.
Should fix https://bugs.launchpad.net/ubuntu/+source/linux/+bug/820746/ .
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes an information leak to userspace, we were handing out un-zeroed pages
for any newly created TTM_PL_TT buffer.
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Tested-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
For ipv6 link-local addresses, sunrpc do not compare those scope id.
This patch let sunrpc compares scope id only on link-local addresses.
Signed-off-by: Mi Jinlong <mijinlong@cn.fujitsu.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
For IPv6 local address, lockd can not callback to client for
missing scope id when binding address at inet6_bind:
324 if (addr_type & IPV6_ADDR_LINKLOCAL) {
325 if (addr_len >= sizeof(struct sockaddr_in6) &&
326 addr->sin6_scope_id) {
327 /* Override any existing binding, if another one
328 * is supplied by user.
329 */
330 sk->sk_bound_dev_if = addr->sin6_scope_id;
331 }
332
333 /* Binding to link-local address requires an interface */
334 if (!sk->sk_bound_dev_if) {
335 err = -EINVAL;
336 goto out_unlock;
337 }
Replacing svc_addr_u by sockaddr_storage, let rqstp->rq_daddr contains more info
besides address.
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Mi Jinlong <mijinlong@cn.fujitsu.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
This patch fixes "Surround Speaker Playback Volume" being cut off.
(Commit b4dabfc452 was probably meant to fix this, but it fixed
only the "Switch" name, not the "Volume" name.)
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are still some leftovers of commit f59ca058
[locking, lib/atomic64: Annotate atomic64_lock::lock as raw]
[ tglx: Seems I picked the wrong version of that patch :( ]
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Shan Hai <haishan.bai@gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Link: http://lkml.kernel.org/r/20110914074924.GA16096@zhy
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ttarget is initialized when the driver is loaded, but tmin is not.
As a result, tempX_max_hyst attributes read 0. Fix this.
Also use THERM_*_THRESHOLD* constants in these initializations instead
of hard-coding the constants.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "R, Durgadoss" <durgadoss.r@intel.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
