Correct ordering of IEs in the mesh beacon while removing unneeded IEs
from mesh peering frames. Set privacy bit in capability info if security
is enabled. Add utility functions to aid in construction
of IEs and reduce code duplication.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to disable ext. PA lines for reading SPROM. It's disabled by
default, but this patch allows using bcma after loading wl, which leaves
workaround enabled.
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace "old" and "new" with number of the first firmware known to use
the given format.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As described at [1] some STAs (i.e. Intel 5100 Windows) can end up
correctly BlockAcking incoming frames without delivering them to user
space if a AMPDU subframe got lost and we don't flush the receipients
reorder buffer with a BlockAckReq. This in turn results in stuck
connections.
According to 802.11n-2009 it is not necessary to send a BAR to flush
the recepients RX reorder buffer but we still do that to be polite.
However, assume the following frame exchange:
AP -> STA, AMPDU (failed)
AP -> STA, BAR (failed)
The client in question then ends up in the same situation and won't
deliver frames to userspace anymore since we weren't able to flush
its reorder buffer.
This is not a hypothetical situation but I was able to observe this
exact behavior during a stress test between a rt2800pci AP and a Intel
5100 Windows client.
In order to work around this issue just tear down the BA session as
soon as a BAR failed to be TX'ed.
[1] http://comments.gmane.org/gmane.linux.kernel.wireless.general/66867
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While at it also fix the indention of the other IEEE80211_BAR_CTRL_ defines.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
b43_op_config and b43_op_bss_info_changed apply many settings by directly
writing to hardware registers. These settings are lost as soon as the core
is restarted and the initvals are reloaded. This was discovered because
restarting hostapd led to the beacon interval getting set to ~33s (see
https://dev.openwrt.org/ticket/8033 for more information).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable ASPM in pci ->probe on upstream (device) and downstream
(PCIe port) component. According to e1000e driver authors this is
required. I did not find that requirement in PCIe spec, but it seems
to be logical for me.
This need to be fixed for CONFIG_PCIEASPM, that will be done later ...
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move common checks into wrapper function. Since ASPM can be only enabled
on PCIe devices ->is_pciexpress check is unneeded.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We always call ->config_pci_powersave() with both restore and power_off
arguments equal to 0 or both equal to 1, so merge them into one
argument.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We'll either hit one of the case labels or the default in the switch
and in all cases do we then 'goto out' and we also have a 'goto out'
after the switch that is redundant. Change to just use break in the
case statements and leave the 'goto out' after the lop for everyone to
hit.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/tracing: Fix tracing config option properly
xen: Do not enable PV IPIs when vector callback not present
xen/x86: replace order-based range checking of M2P table by linear one
xen: xen-selfballoon.c needs more header files
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to some recent optimization done in the way the mac address
bytes are written into the OTP memory, some AR9485 chipsets were
forced to use the first byte from the eeprom template and the
remaining bytes are read from OTP.
AR9485 happens to use generic eeprom template which has 0x1 as
the first byte causes issues in bringing up the card.
So fixed the eeprom template accordingly to address the issue.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hibernating ->resume may not be called by usb core, but disconnect
and probe instead, so we do not increase the counter after decreasing
it in ->supend. As a result we free memory early, and get crash when
unplugging usb dongle.
BUG: unable to handle kernel paging request at 6b6b6b9f
IP: [<c06909b0>] driver_sysfs_remove+0x10/0x30
*pdpt = 0000000034f21001 *pde = 0000000000000000
Pid: 20, comm: khubd Not tainted 3.1.0-rc1-wl+ #20 LENOVO 6369CTO/6369CTO
EIP: 0060:[<c06909b0>] EFLAGS: 00010202 CPU: 1
EIP is at driver_sysfs_remove+0x10/0x30
EAX: 6b6b6b6b EBX: f52bba34 ECX: 00000000 EDX: 6b6b6b6b
ESI: 6b6b6b6b EDI: c0a0ea20 EBP: f61c9e68 ESP: f61c9e64
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process khubd (pid: 20, ti=f61c8000 task=f6138270 task.ti=f61c8000)
Call Trace:
[<c06909ef>] __device_release_driver+0x1f/0xa0
[<c0690b20>] device_release_driver+0x20/0x40
[<c068fd64>] bus_remove_device+0x84/0xe0
[<c068e12a>] ? device_remove_attrs+0x2a/0x80
[<c068e267>] device_del+0xe7/0x170
[<c06d93d4>] usb_disconnect+0xd4/0x180
[<c06d9d61>] hub_thread+0x691/0x1600
[<c0473260>] ? wake_up_bit+0x30/0x30
[<c0442a39>] ? complete+0x49/0x60
[<c06d96d0>] ? hub_disconnect+0xd0/0xd0
[<c06d96d0>] ? hub_disconnect+0xd0/0xd0
[<c0472eb4>] kthread+0x74/0x80
[<c0472e40>] ? kthread_worker_fn+0x150/0x150
[<c0809b3e>] kernel_thread_helper+0x6/0x10
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt status registers should be read in row to avoid invalid data.
Alter "read" method for both bus options to allow reading several registers
in a row and make sure we read interrupt status registers properly.
Read sequence saves 50% of bus transactions compared to single register
reads. So use it also for the result registers, which are also located
in a row.
Also update copyright notice.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
spi_write() requires use of DMA-safe (cacheline aligned) buffers.
Also use the same buffers when reading data since to avoid extra
locking and potential memory allocation in spi_write_then_read().
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Allow driver to be used on Big Endian boxes.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch fixes belows:
1. Fix code style issue.
2. Fix incorrect functions name in comments.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Ian Campbell <Ian.Campbell@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
When do block-attach/block-detach test with below steps, umount hangs
in the guest. Furthermore shutdown ends up being stuck when umounting file-systems.
1. start guest.
2. attach new block device by xm block-attach in Dom0.
3. mount new disk in guest.
4. execute xm block-detach to detach the block device in dom0 until timeout
5. Any request to the disk will hung.
Root cause:
This issue is caused when setting backend device's state to
'XenbusStateClosing', which sends to the frontend the XenbusStateClosing
notification. When frontend receives the notification it tries to release
the disk in blkfront_closing(), but at that moment the disk is still in use
by guest, so frontend refuses to close. Specifically it sets the disk state to
XenbusStateClosing and sends the notification to backend - when backend receives the
event, it disconnects the vbd from real device, and sets the vbd device state to
XenbusStateClosing. The backend disconnects the real device/file, and any IO
requests to the disk in guest will end up in ether, leaving disk DEAD and set to
XenbusStateClosing. When the guest wants to disconnect the disk, umount will
hang on blkif_release()->xlvbd_release_gendisk() as it is unable to send any IO
to the disk, which prevents clean system shutdown.
Solution:
Don't disconnect backend until frontend state switched to XenbusStateClosed.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Cc: Daniel Stodden <daniel.stodden@citrix.com>
Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Annie Li <annie.li@oracle.com>
Cc: Ian Campbell <Ian.Campbell@eu.citrix.com>
[v1: Modified description a bit]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Steven Rostedt says we should use CONFIG_EVENT_TRACING.
Cc:Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Fix regression for HVM case on older (<4.1.1) hypervisors caused by
commit 99bbb3a84a
Author: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Date: Thu Dec 2 17:55:10 2010 +0000
xen: PV on HVM: support PV spinlocks and IPIs
This change replaced the SMP operations with event based handlers without
taking into account that this only works when the hypervisor supports
callback vectors. This causes unexplainable hangs early on boot for
HVM guests with more than one CPU.
BugLink: http://bugs.launchpad.net/bugs/791850
CC: stable@kernel.org
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Tested-and-Reported-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
I made some changes to the entry in the ARM Machine Registry after
submission which was the wrong thing to do.
This patch should help to fix this error.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since clients can have several flags on or off, this patches make them
appear in the local/global transtable output so that they can be checked
for debugging purposes.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
If a node has to send a packet issued by a WIFI client to another WIFI client,
the packet is dropped.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
When a node receives a unicast packet it checks if the source and the
destination client can communicate or not due to the AP isolation
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Clients connected through a 802.11 device are now marked with the
TT_CLIENT_WIFI flag. This flag is also advertised with the tt
announcement.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Several typos have been corrected and some sentences have been rephrased
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
hash_add() returns 0 on success while returns -1 either on error and on
entry already present. The caller could use such information to select
its behaviour. For this reason it is useful that hash_add() returns -1
in case on error and returns 1 in case of entry already present.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
In case we have a pending completion, for example due to a problem with
the input clock which got corrected after we timed out.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
